Search Documents

By Courtney Young, Jerome Downey

"The various technologies developed for treating spent potlining (SPL) from primary aluminum smelters have been reviewed on several occasions. The technologies generally involve physical, chemical, and thermal processes, either individually or in combination, with the primary objective of total recycle, waste minimization, or complete disposal. In general, those technologies geared for recycling involve separations and are therefore subject to recovery inefficiencies that are attributed to several factors. However, the inefficiencies could be reduced or possibly eliminated if the pots were designed for recyclability. This concept is applied to SPLASH, a recently developed SPL management technology.IntroductionAluminum is produced by molten salt electrolysis via the Hall-Héroult process. The process is conducted in an electrolytic “pot,” which is comprised of a steel frame first lined with insulating refractory brick, and then conductive graphite blocks, which serves as the carbon cathode [1, 2]. These materials are collectively referred to as “potlining.” Anodes comprised of petroleum coke/pitch are suspended above the pot and extend down into the molten cryolite (Na3AlF6) electrolyte. The electrolyte temperature is maintained at approximately 980 °C by resistance heating as low voltage (4-5 volts) and high current (50,000-300,000 amps) are applied across the two electrodes.High purity alumina is added to the cryolite bath, where it dissolves and becomes amenable to aluminum reduction at the cathode:"

Jan 1, 2008

By Yu Hu, Gabriella Tranell, Song Zhang, Eivind Johannes Øvrelid

"In the present research, recycling feedstock of silicon for Photovoltic (PV) application is investigated. Whether these recycling feedstocks are reliable in the future use is discussed in this work to assess the properties of the crystal silicon ingot, which is commercially pulled from top-cuts of casted multicrystalline ingot via one kind of Czochralski method - FerroTech. Dopant is the acceptor type Boron (B) and growth direction was <100>. Crystal diameter and the length were 190mm and about 1700mm, which were controlled by the temperature and the pulling speed, then cut to 156mm * 156mm wafers with 2000um and 200um thickness. Resistivity measurements of these wafers by Four Point Probe (FPP) are in good agreement to the calibrated profile after Rapid Thermal Process (RTP). In this work, the Minority Carrier Lifetime MCI, shown by Carrier Density Image (CDI) and Quasi Steady State Photo Conductance (QSSPC), gives the mapping results on the cross section and the relationship to the injection level, increases in an arrange from 40us to 90us along the ingot height, which is abnormal distribution compared to the standard ingot. Then Oxygen and other metal impurities distributions, measured by Flourier Transform Infra - Red (FTIR) respectively, account for the novel phenomenon of the continuously increased MCI. Various types of heat treatments were performed on these wafers (different ingot and different positions) in N 2 and 0 2 mixture atmosphere. Before and after heat treatment, micro-defects were revealed by copper decoration and etching work. Solar cells are fabricated by Energy Research Center of the Netherlands from the experimental ingot, and processed under an industrial standard line. Compared to results of the reference mono-crystalline and multi-crystalline silicon solar cells, the performances of experimental ones show excellent efficiency values up to 18.5%, and Jsc values up to 37mA/cm2.IntroductionThe PV industry has gone through rapid development, with a high growth rate resulting in an increasing demand for silicon feedstock. In addition, costs in production need to be reduced such that solar energy can compete other conventional and renewable energy. Searching low cost, reliable and efficient feedstock is one promoting way to improve and enhance the competitiveness of the PVindustry.More and more researchers start searching new raw materials for PV application [1]-[4]. The key to make full use of low cost raw materials is to control the distribution and effect of impurities, such as Carbon, Nitrogen, and other metal contamination [5]."

Jan 1, 2013

By E. W. Lithgow

Commercial volumes of nickeliferous laterite ores overlie part of a 90 km long belt of peridotites in central Dominican Republic. Protores are serpentinized harzburgites and dunites, with lesser serpentinite. The ore mineralogy consists mostly of goethite, serpentine-group minerals, quartz and poorly crystallized, x- ray amorphous materials. Minor constituents are hematite, gibbsite, olivine and enstatite. In the Ore Dressing plant the mine feed is subjected initially to proper sizing and blending to produce a homogenized mix. Subsequent drying and upgrading, by selective crushing and screening of rock fragments through a Barmac circuit, complete preparation of the ore for pyrometallurgical processing.

Jan 1, 1993

By L. Deininger

The QSL plant in the existing "Betzelius" Stolberg GmbH lead smelter in StolberglGermany was commissioned in August, 1990. Following some modifications to the process and equipment which had become necessary in line with the implementation of this new techno- logy, conclusive operating results are now available. These will be reported together with a short description of the plant design. In May 1992, raw material feeding to the QSL reactor in the new lead smelter of Korea Zinc Co. in OnsanlKorea was started. As all the experience gained up to that point in time in the Stolberg plant had already been incorporated in this plant prior to start-up, it reached stable, satisfactory operating conditions in a short period of time. After an introductory description of the plant important operating results will be reported. The operating experience gained in the two plants fully confirms the correctness of the in- ventors&apos; creative ideas in the 70s. The QSL process meets all demands made on modern, ecologically compatible and energy-saving lead production technology. The paper ends with suggestions on how the QSL process will be optimized further in the future.

Jan 1, 1994

By Oszkar Bíró, Peter Mittag, Bernhard Aigner, Stefan Pirkeri, Philipp Glttleri

"This paper considers CFD modeling of processing and melting of small metallic particles by means of electrical heating. The particles fall continuously onto a liquid metal bath which is heated by an electric arc. After melting of the particles liquid metal is tapped.The charging behavior of the particles in the supply unit as well as in the reactor freeboard is studied by means of Euler-Euler granular simulations. The flow situation in the metal bath due to gas injection and magnetic fields is calculated by combining Navier-Stokes and Maxwell solvers. The macroscopic melting process occurring during the continuous charging of the particles is studied by kinetic laws for melting reactions. The temperature field is evaluated by balancing heat sources due to Joule's heating and heat losses due to latent heat of melting as well as convection and radiation.As a result of these simulations the fully three-dimensional flow fields of particles and gas in the atmosphere is obtained. Furthermore the flow field as well as the magnetic field in the metal bath can be studied. As a main result the three-dimensional concentration field of the still unsolved particles in the liquid metal can be evaluated.IntroductionIn this paper a metallurgical process for melting small iron particles is investigated by means of CFD-simulations. In a first process step the preheated and already mostly reduced iron particles fall continuously into the reactor through a vertical tube mounted at the lid of the furnace. In a second step the particles are melted in the liquid metal bath. Meanwhile the melt is heated by electric arcs to provide the heat needed for melting the incoming particles.In Figure I a sketch of the geometry setup considered in this paper is provided. The particles fall from a height of approximately 12 meters onto the bath surface in the center of the furnace. The melt is heated by electric arcs that are placed symmetrically around the center axis."

Jan 1, 2001

By Fuxing Yin, Akira Sato, Yoshiaki Ohsawa, Kohji Kawaharai

"INCRAMUTE alloy (nominally 45Mn-53Cu-2Al wt. %) has a specific damping capacity as high as 0.4, through a solid-solution and aging treatment. The damping behavior of the alloy is highly temperature-dependent and shows a peak near room temperature. The inadequate strength in the high damping condition restrains the practical application of the alloy, as structural components. Ferromagnetic MnB particles are dispersed in the alloy during induction remelting the matrix alloy in an argon atmosphere. Surface modification of the MnB particles by mechanical alloying (MA) and suitable control of the addition process cause a homogeneous distribution of MnB particles in the alloy. In the composite containing 2 wt. % MnB particles, temperature dependence of damping capacity is improved, and higher damping capacity is still retained in the temperatures over 60 °C. Meanwhile, the Young's modulus and tensile strength were also increased by about 20%. The roles of the MnB particles in improving both damping behavior and mechanical properties were also discussed.IntroductionMany viscoelastic materials, such as rubbers, polymers and plastics, have the superior ability to damp vibration and noise. However, in the applications as structural materials the high damping capacities of materials are pursued upon the satisfactory mechanical properties, especially those at elevated temperatures. Damping alloys are finding more and more applications in structures where noise and vibration ·should be ·eliminated. Specific damping capacity (SDC), defined as the ratio of the energy dissipated to the maximum vibration energy stored per cycle, is usually used to evaluate the damping capacity of alloys. INCRAMUTE damping alloy, developed by the International Copper Research Association, Inc., has a nominal composition of 45Mn-53Cu-2Al in weight percent. The high damping· microstructure of this alloy is obtained through the solution treatment at 820 °C followed by a water quench and aging at 400°C for 10 hours followed by cooling to room temperature [1]. With the heat treatment, a SDC peak ·vs. temperature of as high as 0.4 was observed in the alloy at the strain amplitude of about 10-3 while a tensile strength of about 500MPa was sustained."

Jan 1, 2000

By Peter K. Eriksson

Nanofiltration is very efficient in separating heavy metals from water solutions, even if they contain strong acids. Desalination System, Inc., has many years of experience in this area, and this paper deals with three different such cases. The first case deals with concentrating the heavy metals in the pregnant leach solution from a copper dump leaching site with a surplus water problem. The increased copper concentration in the pregnant leach solution increases the capacity of the following copper extraction stage. The nanofIltration permeate is polished with a biomass adsorption column to remove the small amounts of remaining heavy metals, before being discharged. This method eliminates sludge handling and disposal, which are quite costly with the alternative precipitation process. In the second case, a complicated precipitation method was used to remove heavy metals from the waste stream of a specialty metals manufacturer. Nanofiltration was installed to increase the metals concentration four times, which greatly simplified the precipitation process. The chemical consumption and sludge production decreased by more than 80 percent, and the labor cost decreased by 66 percent. In the third case, nanofiltration was used to purify waste sulfuric acid solutions containing heavy metals, to meet the specifications for technical grade acid. Sulfuric acid concentrations above 30 weight percent were successfully purified in a multiple pass membrane system.

Jan 1, 1996

By Kotaro Ogura

"The electrolysis process in which CO2 is selectively reduced to C2H4 at a three-phase(gas/solution/metal) interface on a copper-mesh electrode has been developed in a concentrated solution of potassium halide. At open-circuit potential, CO2 is captured on the electrode by being inserted into the double-layer consisting of halide anions specifically adsorbed and potassium cations which are located in the Helmholtz inner and outer layers, respectively. CO2 thus activated is subjected to the electrochemical reduction. In the early stage of reduction, CO2 is converted to formate radicals that are adsorbed on the electrode by taking the place of halide anions. The reductive coupling of these radicals results in the formation of intermediates such as -CH2C(O)- and CH2=CH-, and C2H4 is finally produced. The catalytic activity of the electrode process involving the insertion of CO2 into the double layer is not deteriorated at all during the electrolysis, and the continuous reduction of CO2 to C2H4 is possible with the addition of inorganic acid under the assistance of natural energy.Carbon dioxide is a serious pollutant released from fossil fuel power station, internal combustion and many industrial operations. The easy release of CO2 to the air has caused the global warming, and the technique which intends to curtail CO2 by pushing it back into the ground has been suggested. However, this problem should be greatly mitigated if CO2 can be converted to innocuous substances. Especially, the reuse of CO2 as fuels and chemicals is extremely effective not only for the mitigation of the global warming but also against the depletion of the fossil fuel reserves. Several processes for converting CO2 to valuable compounds have been proposed including hydrogenation over heterogeneous catalyst at high temperature and electrochemical and photochemical reduction. In the conversion and cutback processes of CO2, however, it is of importance that the process is feasible under mild conditions, because the secondary generation of CO2 is feared if high energy is required and supplied with a fossil fuel. In this meaning, the electrochemical reduction of CO2 taking place at room temperature, which is similar to photosynthesis, is promising. From the practical point of view, it is further necessary that the conversion rate is high enough and the product is satisfactorily valuable."

Jan 1, 2008

By J. R. Parga

A shortage of landfill space and growing environmental concerns in Mexico are renewing interest in the recyclability of scrap from automobiles. This work describes a pyroumetallurgical process for the recovery of metallic lead from waste lead paste. Argentopyrite concentrate is commingled with lead paste residue and smelted in a fuming process thereby transferring the precious metals into lead bullion. The process consists of smelting lead paste and argentopyrite, sodium carbonate, and metallic iron at smelting temperatures of about 1100 T. The reaction products are slag and molten lead bullion enriched with precious metals. A major feature of this process is the removal of precious metals from the bullion by means of zinc, whereby a silver-zinc intermetallic compound is formed and floats out of the lead. The recoveries of precious metals are about 98%.

Jan 1, 1996

By Gunnar Eriksson

Computer simulation has become an everyday practice in thennodynamic and materials research. Advanced thennochemical algorithms take into account heat transfer effects and salient reaction kinetics when applied for process models. In particular, the combination of mass transfer or overall reaction rates with multi-component Gibbs energy minimisation provides an effective tool for simulation of industrial thennochemical processes and processing of materials. In this work the combination of rate factors with the Gibbs energy technique was studied by using the novel program ChemSheet, which operates through Microsoft&apos;s Excel® spreadsheets. Such processes as, for example, CVD of pure silicon production, titania pigment manufacturing, vapour pressure of Mercury in amalgams (in Hg-Iamp manufacturing) and melting behaviour of low-temperature alloys have been modelled. Provided that the thennochemical data is available simulations can be performed with any thennodynamic system. The calculation can be performed as an affinity study without a particular reactor model or with a specific reactor scheme.

Jan 1, 2001

By H. Hirayama, T. Okura, O. Kato

"Saganoseki Smelter & Refinery, one of the largest copper smelters in the world, has the annual capacity of 300,000 metric tons in copper content with two flash furnaces, six Pierce-Smith type converters, two anode furnaces, four acid plants, three tank houses and perfect pollution control system.Coping with the many severe conditions surrounding the copper industry in the last decade, Saganoseki Smelter has kept performing the stable operation, while enhancing the smelting capacity and developing new technologies such as the hydrometallurgical treating of converter dust recovered at electric precipitators. Especially in the operation of flash furnaces, which are of Nippon Mining's conversion type using hot air in a temperature of l,000ºC some technological improvements and complete operation control factors have approved the concentrate feed rate to reach to 2,200 tons a day for a flash furnace.Reported in this paper are the production control design for copper smelting process, and the operation control scheme of the flash furnace following the brief review of the characteristic of Saganoseki Smelter's process and some improvements. Copper Smelting ProcessDescriptions of major unit operations and general specifications of the copper smelting facilities are summarized in Table 1, and the present flowsheet of the copper smelting is described in Figure 1 (1,2).Outputs and raw materials treated in the last five years are shown in Table 2, in which concentrate includes powder copper scrap which amounts to 3 to 4% of concentrate.A full operation was performed for a period of one month, for both one flash furnace operation and for two flash furnace operation. With one furnace operation, 19,200 tons of copper were produced. With the two furnace operation, 84,000 tons of concentrates were charged and 33,500 tons of anode (net 28,600 tons of copper) were produced.The actual production level, however, has been kept at 80 to 90% of the full capacity because of low copper price, tight market of copper concentrate or fall of net demand in Japan."

Jan 1, 1989

By W. John Rankin

The finite and non-renewable nature of mineral resources poses unique challenges for sustainability: How can mineral and material needs of society be satisfied indefinitely? How can the benefits of exploitation of minerals best be captured for present and future generations? How can the environmental problems caused by large scale mining and processing best be ameliorated? These issues are rarely addressed, or if so only incidentally, in traditional courses in geology, mining, metallurgy and materials yet addressing them will increasingly be a major role for professionals in the minerals and materials industry and related sectors and agencies. This paper describes a framework for examining these and other sustainability issues related to meeting future material needs from non-renewable resources. The framework may be useful for educational purposes, either as the basis of a dedicated subject or by including the elements of it throughout a traditional course in relevant subjects.

Jan 1, 2014

By Mark Cross, Hadi Abou-Chakra, Nicholas Christakis, Mayur K. Patel, John Baxter, Ugur Tiizful

"In recent years significant effort has been put into using continuum mechanics for the description of granular flows. Although these models are partially successful in capturing some flow characteristics, they lack essential information on material properties, which are needed to account for the interactions between different particles. Thus, they are incomplete and can not be used to describe processes such as hopper filling/emptying and pneumatic conveying, where particle-particle interactions can lead to phenomena such as segregation, degradation and agglomeration. In this paper, a 3-D unstructured finite-volume framework is presented, which employs interface tracking techniques to solve for the individual material components of the granular mixture in the bulk and thus, determine the material-air interface. Various transport processes, arising from the micro-mechanical properties of the different particle species in the granular mixture, can be obtained through kinetic theory. The transport coefficients of each of the individual species can be determined and analysed in a micro-mechanical framework and the transport process parametrised in the form of constitutive models. These models provide the continuum theory with information on the micro-mechanics.This work describes the continuum framework and the micro-mechanical parametrisations, which are used to describe the processes and interactions at the microscopic level. Numerical simulations and comparisons with experimental data are then presented for the case of binary granular mixtures and conclusions are drawn on the capability of the model to realistically predict and quantify the main characteristics of granular flows."

Jan 1, 2001

By Emil B. Milosavljevic, Ljiljana Solujic

Cyanide is exceptionally reactive, and in typical gold/silver processing liquors, cyanide may be transformed into various species and forms depending on the mineralogy of the ore and chemical make-up of the process water. The exact speciation and relative concentrations depend on the Eh and pH values, as well as the free CN concentration in the system. Very good cyanide balances can be achieved by the judicious selection of the analytical techniques used. The choices an analyst has to make (which analytical methods to use and which ones to avoid) in order to gain better understanding of cyanide speciation and balances in a particular system under investigation will be discussed. Examples of cyanide balances obtained for the laboratory scale tests (agitated leach and column tests) will be presented and discussed.

Jan 1, 1999

By Hong-ying Xia, Bao-bao Wang, Jin-hui Peng, Bing-guo Liu, Li-bo Zhang, Zhi-qiang Li

Based on optimization using response surface methodology designed by Box- Behnken, to study the interaction of wet industrial salt with moisture drying temperature (50-90 ); duration (10-50s); and the weight of the materials (20-60g). The results show that: the experimental parameter conforms to the quadratic equation model to influence the moisture content and the dehydration speed., in analyzing the significance and the interaction of various factors, the optimum by the Design Expert software conditions for drying with microwave radiation include temperature of 90 , duration of 10s, and sample mass of 26g. Verified by experiment, the moisture content after drying is less than 0.25% and the dehydration rate reached 1.37g/min, between the predicted value and the actual value confirmed good fitting degree.

Jan 1, 2015

By Hong Yong Sohn

A novel flash ironmaking technology is under development at the University of Utah under the support of U.S. Department of Energy (DOE) and American Iron and Steel Institute (AISI). The history of the development from the conception of the idea to the current status will be discussed. The flash ironmaking process produces iron directly from fine iron ore concentrates without requiring cokemaking and pelletization/sintering, which will enable the technology to significantly reduce energy consumption and carbon dioxide emissions compared with blast furnace ironmaking. Unlike other gas-based ironmaking processes, this technology will not suffer from the problems of solid sticking and fusion. Current work is focused on the method of supplying the energy required to maintain the necessary temperature, as an intermediate step to determine the scalability for larger, industrial-scale pilot trials.

Jan 1, 2014

By Olga Frank-Kamenetskaya

The experimental results of study of atmospheric corrosion processes on Saint-Petersburg bronze monuments surface, received in situ and by means of simulating experiments, have been discussed. Influence of the time factor on corrosion film (patina) mineral composition has been analyzed. Direct dependence between patina mineral composition and environmental conditions has been proved. The sequence of patina phases crystallization has been established. Effect of the chemical composition and heterogeneity of artistic bronze and also monument surface structure on the rate of corrosion process has been regarded. The time variations of mass of the crystallized in the hydrochloric acid vapor phases have been investigated. The kinetic laws of their development at the initial stage of formation, indicating simple (non chain) reactions, have been revealed.

Jan 1, 2006

By Howard K. Worner

"In a rewarding career spanning nearly two thirds of a century, the author has worked at the frontier of such diverse fields as the creep of metals, structure properties and production of novel dental and surgical materials, molten salt electrolysis for titanium production, greatly improving the productivity of large iron blast furnaces and of oxygen steelmaking. While each of these has given great satisfaction, special thrills have derived from the development of new methods for the continuous production or refining of both ferrous and non ferrous metals. A rewarding segment was the evolution of various aspects of WORCRA technology. Unfortunately, several of these inventions have been ""ahead of their time"". Introduction""I am greatly honoured by the convening of this meeting to recognise my contributions to pyrometallurgy. My appreciation is the greater because this is the third Howard Worner Symposium; the first took place in the University of Newcastle in 1988, close to my 75th birthday. It was arranged by the local branch of The Australasian Institute of Mining and Metallurgy with the theme, ""Frontiers in Pyrometallurgy"". The second was organised by the University of Wollongong in conjunction with the Australian Academy of Science and the Australian Academy of Technological Sciences and Engineering; it celebrated my 80th birthday and, at my request, covered a broad range of topics under the heading of ""Recent Advances in Science and Technology"". Now, this very international meeting on ""Injection in Pyrometallurgy"" has been convened by the G K Williams Co-operative Research Centre for Extractive Metallurgy in my alma mater. I am both delighted and honoured that the cosponsors are the TMS (USA) and ISIJ (Japan).Dr Madhu Nilmani consulted me about the field to be covered and I readily concurred because ""injection"" has been of keen interest to me since the beginning of the 1960s when I began my pioneering work on sequential oxygen (or air) injection into flowing streams for both refining of blast furnace hot metal to steel and for the continuous smelting-converting of copper and nickel."

Jan 1, 1996

By Tim B. Vander Wood

Standard methods of determining clay mineral powder aspect ratios involve manual scanning electron microscopy analyses of shadowed particles in order to measure both platelet thickness and diameter. We present a method whereby the diameters of platelets are quickly determined by automated scanning electron microscopy and their images are recorded and digitally transferred to a transmission electron microscope equipped for parallel electron energy loss spectroscopy. Thickness&apos; of platelets whose diameters are known from the previous analyses are determined by measurement of the ratio of scattered and unscattered electrons in the beam after it has been transmitted through the platelet.

Jan 1, 1995

By Matthew Tunnicliffe, Akram Alfantazi, Paul Nesbitt, Farzad Mohammadi

"Lead and its alloys are proper candidates for anodes in electrowinning processes mainly because they are insoluble in the leach solutions and relatively cheap. However, the annual cost of corrosion problems associated with these anodes is millions of dollars. In this study lead-silver and lead-calcium anodes were tested under typical nickel electrowinning conditions and the effect of chloride on the corrosion performance of the anode materials was investigated. Corrosion rates of the anodes were calculated using the discharge plateau (reduction of lead dioxide to lead sulfate) after galvanostatic experiments. It was found that lead calcium anodes have the highest corrosion rate both in the presence and absence of chloride. Surface morphology of the electrodes was studied using SEM and the corrosion products were characterized using XRD.IntroductionLead (Pb) is usually the preferred material for commercial anodes since it is insoluble in the leach solution and the costs are manageable. One advantage of using an insoluble material as an anode is the higher purity of the cathodic deposits and better quality of the end product. During nickel electrowinning, metallic nickel is deposited on the cathode while oxygen evolution reaction (OER) takes place on the anode. In practice, relatively high potentials are necessary for the reaction to proceed at the desired rate because of the high overpotential of OER on lead. Lead anodes get oxidized in typical electrowinning conditions and usually have two to three years of lifetime. Although the price of each anode is insignificant, the overall cost of corrosion of these anodes is considerable, which is due to the large number of anodes used in a plant, typically two to three thousand. Therefore, corrosion is a significant problem associated with lead anodes in commercial nickel electrowinning plants and industries show interest in addressing this problem. Corrosion of lead electrodes in acidic environments has been previously the subject of many research studies [I-7]. It has been reported that, during the anodic polarization of lead, several phases may be present on the surface, depending on the potential range that is being studied [8]. Lander showed that lead is oxidized at potentials higher than 0.252 YsHE with tetragonal lead monoxide being the main reaction product [9]. At 0.666 YsHE lead can transform to lead dioxide; however, it is not stable and transforms to lead sulfate and lead oxide. At potentials higher than 1.684 YsHE, lead dioxide is eventually a stable phase and forms a protective layer on the surface [I 0, 11]. Under conditions of a typical nickel electrowinning plant, usually a 200 A/m2 current density is passed through the electrodes."

Jan 1, 2012