Search Documents

By Soumendra Basu, Uday Pal, Yang Yu, Srikanth Gopalan, Karl Ludwig, Deniz Cetin, Jacob Davis

"A limiting factor for Solid Oxide Fuel Cell (SOFC) performance is the oxygen reduction reaction (ORR) at the cathode surface. Changes in the surface composition and structure on annealing at 800°C has been studied, since these can influence the ORR. Idealized single crystals of cathode materials La0.8Sr0.2MnO3 (LSM) and La1-xSrxCoyFe1-yO3 (LSCF) were grown as heteroepitaxial thin films on lattice matched single crystal substrates. Changes upon heating the films to operating temperature and pressures were characterized using various synchrotron x-ray techniques. Total Reflection X-ray Fluorescence (TXRF) measurements, which probe compositional changes, were made at high temperature in real time. The LSM surfaces were found to develop manganese enrichment when heated. Highly strontium doped LSCF were found to develop strontium-rich surfaces. HArd X-ray PhotoElectron Spectroscopy (HAXPES) was used to investigate the electronic structure of the materials. Highly strontium doped LSCF precipitates a surface strontium phase that contains both oxide and carbonate contributions.IntroductionSolid oxide fuel cells (SOFCs) are chemical to electrical energy conversion devices that could potentially reshape how energy demands are fulfilled. SOFCs have a potential efficiency over 70%, fuel flexibility, low emissions, and low degradation over long time scales. Commonly, SOFCs are operated at high temperatures (above 800°C). At these temperatures expensive housing is needed to contain an operating stack as well as coatings to contain the oxidation of the metallic interconnects. Lowering the temperature of an operating device would allow for more conventional materials to be used, thus lowering overall cost. Understanding the reaction kinetics of the oxygen reduction reaction at the surface of the cathode is vital to designing a system that will perform well at lower temperatures. A commercialization goal is to reduce operating temperatures without sacrificing performance.In order to exploit the advantages of SOFCs, an understanding is needed of the surface chemical states of cations on the surface of the cathode and how this relates to the oxygen reduction reaction (ORR):"

Jan 1, 2014

By Pinakin C. Chaubal

An industry ? university consortium was set up to develop advanced tools necessary to understanding of the various phenomena occurring in the hearth of the modern iron making blast furnace. The major driver for this work was to provide the technological support required to extend campaign life of blast furnaces, which, by current agreement is tied to the life of the furnace hearth. The hearth wear is significantly affected by the hot metal velocity, temperature distribution and refractory temperatures. Due to the difficulty in making measurements inside the hearth, novel approaches to gain a fundamental understanding of the detailed physical and chemical processes in the hearth must be developed. The approach used in this project was to develop a 3-D CFD (Computational Fluid Dynamics) model coupled with extensive validation efforts. The CFD model is being utilized (1) to understand the phenomena in the hearth, (2) to understand the impact of changes in the internal conditions of the hearth on wear patterns; and (3) to design a monitoring/controlling system for prolonging campaign. In this paper, the results will be reviewed.

Jan 1, 2006

By R. W. Adams

A new process has been developed for leaching zinc sulphide concentrates at atmospheric pressure using air or oxygen plus nitrogen dioxide in dissolved or gaseous form as? an oxygen carrier. The process is flexible and can cope with variations in the degrees of retention and regeneration of dissolved nitrogen dioxide in the leaching phase. By controlled addition of concentrate a leach solution with low residual nitrate concentration can be produced. Following separation by filtration of unleached solids and elementa1 sulphur and conventional oxidation/precipitation of dissolved iron, the leach liquor can be treated with metallic zinc to remove the remaining nitrate and other meta111c impurities such as copper, cadmium and cobalt to provide a solution suitable for electrolytic recovery of zinc. Pilot scale testing of the process .has given zinc recoveries in the high nlnet1es, production of a hi.gh grade jarosite-free Pb/Ag residue (50% Pb.) and a saleable high grade of elemental sulphur. .A wide range of concentrates can be treated containing substantial levels of lead and copper as well as zinc. Indicative cost estimates suggest that the new process is competitive with alternative procedures such as pressure leaching.

Jan 1, 1990

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for four years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace's hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1997

By S. C. Grund

In secondary copper smelting as it is performed at Hüttenwerke Kayser plant in Lünen, tin-and lead-containing flue dusts are produced as intermediate products. These flue dusts are further processed in a hearth furnace. Followed by certain refining operations a saleable tin-lead-alloy is produced. Even though the hearth furnace technology has been in use for this purpose for a long time still its performance undergoes changes in search for optimum processing conditions regarding to the increasing complexity of the raw materials and tightening economical and ecological boundaries. The use of modern statistical tools for the calculation of accurate mass balances is demonstrated for the tin-lead hearth furnace. These reliable mass balances are the basis for any further modelling of the process with the aim of optimization. Incorporating metallurgical knowledge and experience as well as different mathematical modelling techniques, further studies are planned in which the recoveries of valuable and minor elements and their dependency from various process parameters are examined. The aim of this modelling is to optimize the recoveries of the valuable elements, to minimize the energy consumption and the processing costs and thus to keep the process competitive in a harsher economical and ecological surrounding. The modelling principles are transferable to other metallurgical operations and are especially suited for ill-defined pyrometallurgical processes.

Jan 1, 1999

By Ruiqing Li

It is possible to purify some liquid metals by exploiting the difference between the vapour pressure of the bulk metal and the minor constituents or impurities. The rates of purification can be improved by carrying out the process under reduced pressure, that is, so called, vacuum. Some commercial examples of vacuum refining are the purification of molten tin to eliminate trace amounts of lead and the refining of cobalt, also to remove lead. The objective of this paper is to review the basic theory behind vacuum refining technology in order to show how the feasibility of vacuum refining can be determined simply for a particular system by evaluating Olette's Volatility Refining Criteriont.

Jan 1, 1991

By J. W. Lyman

The U.S. Department of the Interior, Bureau of Mines, investigated methods to recover valuable rare-earth materials from NdFeB magnet scrap. Although several processing techniques were evaluated" the best separation of rare earths from the NdFeB magnet ,scrap was obtained by sulfuric acid dissolution followed by precipitation of recyclable rare-earth salts. Both sodium and ammonium intermediate double-salt precipitates' that can be converted to a variety of useful neodymium products were investigated. The sodium system showed a neodymium recovery of 98 pct, while the ammonium system yielded 70 pct during double-salt precipitation. The iron-rich effluent following the rare-earth recovery was treated to produce sodium and ammonium iron jarosites that can be disposed of or converted to hematite. By following this new procedure, many materials handling and economic disadvantages found with fluoride or oxalate direct precipitation were avoided.

Jan 1, 1992

By A. Barba, M. P. Gómez, F. Puertas, M. Palacios, M. F. Gazulla, S. Martínez-Ramírez, I. García-Díaz

"The present study explores the reactivity and burnability of cement raw mixes containing fired red or white ceramic tile wastes or combinations of the two as alternative raw materials. The results showed that the new raw mixes containing these wastes are technically viable. The reactivity and burnability of the new raw mixes have been evaluated; confirming very good results when the particle size of wastes was less than 90 µm. The chemical and mineralogical compositions of the new clinkers were comparable to clinker manufactured with conventional raw materials. The mix of red and white ceramic tile waste was found to perform as well or better than each type of waste separately, a promising indication that separation of the two would be unnecessary for these purposes.IntroductionPortland cement clinker production consumes large amounts of energy (850 kcal/kg clinker) and has a considerable environmental impact. This involves massive quarrying for raw materials (limestone, clay etc), as it takes 1.7 tonnes to produce one tonne of clinker, as well as the emission of greenhouse and other gases (NOx, SO2, CO2) into the atmosphere. Around 850 kg of CO2 are emitted per tonne of clinker produced.The cement industry is looking for solutions to these problems, to attain sustainability and comply with the Kyoto Protocol commitments [1,2]. For that reason, experimental ways are being explored to develop cements whose manufacture is less energy-intensive, less damaging to the surrounding environment and with lower tendency to emit polluting gas. One of the reach this objective is the use of industrial waste and by-products as alternative materials for cement manufacture. Such alternative materials may partially replace fuel [3,4], conventional raw materials [5-8] or clinker in the final composition of the cement [9]."

Jan 1, 2008

By W. L. Dalmijn

The processing of scrap and scrap cars starts with size reduction by a hammermill, or shredder. After the liberation the magnetic fraction is removed. The remaining non¬magnetic fraction mixed with other materials is screened and each fraction is processed separately. The increased use of plastic has a negative effect on the recovery of metals and waste production. At Huron Valley, Belleville Michigen, USA, the non-ferrous fraction from 5 million obsolete cars per year, containing 200,000 tons of non-ferrous metal, is processed. Aluminium Is recovered with a heavy medium separation process and concentrated with eddy current separators. The remaining heavy non-ferrous fraction is concentrated by a new combination of eddy current separation and image processing. After this separation process the zinc fraction is melted and refined and the copper, brass, stainless steel and other high-quality concentrates are sold to the secondary industries. The recycling of car scrap has become an important source of metals and materials for the secondary. materials processing industry.

Jan 1, 1995

By Thomas J. Keefe, O&apos

Results of metal electrodeposition experiments conducted at the University of Brussels and University of Missouri-Rolla over the past few years are reviewed in terms of the relationship and impact on industrial processes. Examples are cited from common electrowinning, electrorefining, or electroplating operations for copper, zinc, nickel, cobalt and silver. The following topics are considered : metallographic structure, crystallographic texture, surface morphology, nucleation and growth, additive monitoring and effects, high current density, substrate related properties including adhesion. The studies were conducted on a variety of scales from laboratory beaker tests to full sized pilot and industrial operating plants.

Jan 1, 1993

Arsenic occurs naturally in rocks and soils, water, air, plants and animals. It can be further released into the environment through natural activities such as volcanic action, erosion of rocks and through human actions. Higher levels of arsenic tend to be found more in ground water sources than in surface water sources of drinking water. Compared to the rest of USA, western states have more systems with arsenic levels greater than 10 parts per billion (ppb). The US Environmental Protection Agency (EPA) has historically regulated arsenic in drinking water at 50 ppb, but the agency has lowered the maximum contaminant level (MCL) for arsenic to 10 ppb-to be in compliance by January 2006.This paper reviews briefly a) aqueous arsenic chemistry and removal mechanisms and b) the available treatment processes to attain the drinking water standard of 10 ppb by 2006. The combining of an appropriate removal method with an existing system depends on several factors such as nature of arsenic, the water source, existing plant equipment and processes site conditions etc. The paper also includes one or two case studies from the State of Arizona. Key words: Arsenic, Drinking water, Treatment Technologies

Jan 1, 2005

By Mohamed Y. Bakr, Aly M. Abdel-Rehim

The present work is related with mechanical activation of processing of Egyptian wolframite by simultaneous ball-milling and pressure alkaline leaching, to improve the recovery of tungsten from wolframite. The results show a total recovery of tungsten from wolframite (97.8- 98.7%) by simultaneous ball–milling and alkaline leaching at temperature 175-200oC. It is concluded that processing of wolframite by simultaneous ball- milling and leaching is mechanically activated and accelerated as a result of the grinding action of steel balls that caused the immediate rupture by continuous removing the product layer of the reaction ( sodium tungstate and iron and manganese hydroxides ) from reacting particle surfaces. This leads to the exposing of fresh and activated wolframite particle surfaces to alkaline leach solution and consequently the acceleration of the reaction of wolframite leaching .The results of the kinetic study 0f alkaline processing of wolframite and its mechanical activation show that the system is under kinetic control.

Jan 1, 2015

By James D. O, DeLa&apos

Multicomponent materials are common in nearly all areas of materials science and technology, yet the use of phase diagrams to represent these complex systems is hampered by the requirement of three or more dimensions for explicit graphical representation. In the present work, the "solid-modeling" capabilities of a computer aided design (CAD) system have been applied to the representation of three-dimensional phase diagrams. Relevant phase diagrams for a hypothetical quaternary eutectic system were constructed and used to demonstrate the capabilities of the technique. These capabilities lead to relative ease of phase diagram construction and improved access to qualitative and quantitative information. Results of this work are contrasted and compared to previous efforts toward computer ,representation of phase diagrams. It is concluded that solid-modeling of three-dimensional phase diagrams can be used to advantage in both education and research.

Jan 1, 1991

By A. M. Blount

In 1983, a final ruling of the U.S. Occupational Health and Safety Administration (OSHA) specified that chemicals containing >0.1 % of a carcinogenic substance or > 1 % of a substance hazardous to health must be labelled. Amphiboles of the fibrous or asbestos-type must be quantified at levels of 0. I % whereas the status of non-fibrous types is not finally determined at this time. Tremolite and actinolite can possibly be measured to 0.1 % by XRD, but anthophyllite cannot be so measured. Recently the International Agency for Cancer Research (IARC) has designated quartz as a suspected carcinogen, and its quantity must be measured to the 0.1 % level. Thus, it has become Increasingly important to be able to detect and quantify minerals in bulk samples down to low or "trace" levels. It has been found that minerals needing to be quantified can often be concentrated by microcentrifuge and counted by means of polarized-light microscopy. For example, amphiboles in talc samples can be separated by using a heavy liquid (thallium formate-malonate) of density 2.810. Talc floats, and amphiboles sink. After centrifuging, the denser particles are removed from the bottom with a Pasteur pipette and placed in a clean centrifuge tube. Distilled water is added to the tube containing the denser minerals and the tube centrifuged again. After several washings with distilled water, the sample is removed along with a drop of water to a clean glass slide. A drop of 1 .584 refractive index liquid and a cover glass are placed over the dried sample. The slide is scanned for particles greater than 5 um in length and having an aspect ratio greater than 1:3. These are checked for refractive index, sign of elongation and extinction angle to differentiate them from talc particles on edge and other minerals. Amphiboles have all indices greater than 1.584, and talc has all indices equal to or lower than this value. Alternately the heavies at the bottom of the centrifuge tube can be filtered through a nucleopore filter. After the filter has been washed with distilled water and dried, a 1.584 refractive index liquid renders the filter transparent in two of the four extinction positions so that a count of amphibole particles can be made directly on the filter. The refractive index-density method which is so useful for talc powders should be equally useful for other nonsoluble industrial minerals.

Jan 1, 1989

By T. W. Turk

In May 1984, Davy McKee Corporation was awarded a contract for engineering design, procurement assistance, project management and startup services for two gold recovery plants? in the People's, Republic of China (PRC). The basic design of these two projects was to be accomplished by a combined effort of the Chinese and Davy McKee Corporation (DMC). The, design goals were to provide a state-of-the art plant while maintaining Chinese standards and design practices whenever possible. Chinese-manufactured equipment was to be used as much as possible. This paper discusses the project organization and procedures developed to accomplish the design goals, the process selection and design, and the selection and procurement of equipment outside of the PRC. Design development for grinding, leaching and carbon adsorption, and gold recovery are discussed in detail. The major goal of process selection and design was to provide common criteria for both plants. Equipment .sizing and selection was identical for carbon-in-leach adsorption, gold recovery, acid washing, and carboo regeneration for both plants. Of special importance is the design of the wastewater treatment system. Due to the cl0se proximity of a major population area, slurry discharging from these mines must be treated to meet drinking water standards. The process development and design of this system is also discussed in detail.

Jan 1, 1989

The oxidation of zinc vapour plays a very important part in the operation of the Imperial Smelting Process. The kinetics of the reoxidation of zinc vapour by carbon dioxide and water vapour onto quartz and zinc oxide substrates is qualitatively understood and this pertains to the conditions found as the gases are being transferred from the furnace to the splash condenser. However, re-oxidation also occurs in the shaft of the furnace where the solid substrates are sinter and metallurgical coke. It was found that there was a threefold increase in the rate of oxidation on sinter, compared to quartz and a 30 to 300 increase in rate on the coke. This was attributed to the high surface area offered by these materials.

Jan 1, 2003

The oxidation of zinc vapour plays a very important part in the operation of the Imperial Smelting Process. The kinetics of the reoxidation of zinc vapour by carbon dioxide and water vapour onto quartz and zinc oxide substrates is qualitatively understood and this pertains to the conditions found as the gases are being transferred from the furnace to the splash condenser. However, re-oxidation also occurs in the shaft of the furnace where the solid substrates are sinter and metallurgical coke. It was found that there was a threefold increase in the rate of oxidation on sinter, compared to quartz and a 30 to 300 increase in rate on the coke. This was attributed to the high surface area offered by these materials.

Jan 1, 2003

By A. Jakobsson

Studies of the rate of interdissolution in oxide systems in the solid state are of importance in materials processing through the powder-metallurgical route. As there is a need for following the rate of the such reactions continuously, a new method based on high temperature X-ray diffraction was developed. Mechanical mixtures of the oxides were placed in a high-temperature X-ray diffraction unit and the changes in the intensity and position of the peaks with highest intensity for both the components were followed as functions of time. A suitable theoretical model has been developed in order to interpret the experimental data and evaluate the diffusion coefficients. The method was applied in the case of the system MgO-NiO. The results obtained are compared with those obtained by another new method, based on solid-state galvanic cell technique with calcia stabilized zirconia electrolyte, developed in the Department of Theoretical Metallurgy. The advantage of the present techniques to monitor the progress of the reaction continuously make them suitable for computer control of such processes.

Jan 1, 1995

By K. Osseo-Asare

Third phase formation, the separation of a solvent extraction organic phase into two liquids, is generally attributed to the limited solubility of the extracted complexes in the hydrocarbon diluents. Much of the research on third phase fomiation, therefore, emphasizes experiments designed to establish the stoichiometry of the species responsible for the limited solubility. This work offers a different approach, based on the recognition that the solvent extraction third phase, in fact, corresponds to the middle phase in a microemulsion fluid system. Using the tri-n-butylphosphate (TBP)-diluent-water-electrolyte system as a model system, current concepts of microemulsion phase behavior are utilized to develop a general framework for interpreting and predicting the patterns of phase behavior in solvent extraction systems.

Jan 1, 1999

By QinGuo, Shenghui Guo, Lei Li, Jinhui Peng, Linqing Dai, Libo Zhang

The ferrous removal process after carbothermic reduction of chromite fines with microwave heating combined with leaching was investigated. Under the following conditions: Reaction temperature: 1150 , Reaction time : 40min, Semi coke ratio: 12% , the iron content of the reduction product : 13.05% . Metallization achieved was 52.7%. Reduced chromite was leached with 8% of H2SO4 and FeCl3 aqueous solution. The results show that: the recovery rate of chromium can reach 88.06%, the mass ratio of chromium to iron is 3.5:1 for leaching 30 minutes with 8% of H2SO4; the recovery rate of chromium can reach 88.91%, the mass ratio of chromium and iron is 2.56:1 for leaching 4h at room temperature with FeCl3 aqueous solution (100g/L). The leaching time of latter is longer but can realize the circulation effectively and reduce the waste liquid processing problem.1

Jan 1, 2016