Search Documents

By James B. Fletcher

The Miami mine is located near the town of Miami, Gila County, Arizona. The Miami mine started mining in 1910 and finished in July, 1959. The orebody was divided and mined as follows: Tons High Grade 24,400,000 - Top slicing, sub-level caving, etc. Low Grade 105,100,000 - Block caving Mixed ore 9,800,000 - " Low Grade #2 13,100,000 - " Total Mining 152,400,000 GEOLOGY Ore minerals are largely in pre-Cambrian Pinal schist intruded by tertiary Schultz granite porphyry and covered to some extent by Quarternary Gila conglomerate. The structures are highly faulted and shattered. The Miami fault on the east cuts off the ore and the Pinto fault on the southwest caused re-oxidation of enriched sulphides producing mixed ore. MINERALOGY The chief mineral is chalcocite, with chalcopyrite, bornite, covellite, malachite, azurite, chrysocola, cuprite, native copper, and molybdenite as minor minerals. The ore minerals occur in seams, veinlets and disseminated particles. In block caving there is always some dilution, and drawing of ore stops when the grade drops past an economical point. This results in a small amount of copper left in the stopes below the capping. There is some copper in the capping, probably below 0.03% or less than 0.6 lbs. per ton. Over the low grade #2 orebody and portions of the high grade there was an oxide capping which was not mined. The crushed pilars are another source of copper. The leaching at Miami is an attempt to recover this last remaining copper of a worked-out mine. The enrichment at the Miami mine had gone more nearly to completion than most ore bodies in the southwest. There is practically no pyrite in the capping and very little in the ore.

Jan 1, 1971

By Barry Voight

The law [ ] where [ ] is a measurable quantity such as strain and A and cu are empirical constants, describes the behavior of materials in terminal stages of failure under conditions of approximately constant stress and temperature. Applicable to intact rock and rock masses, the relation may be extended to conditions of variable stress and cyclic stress, and may be used to predict time to failure. Applications in rock mechanics include slope and excavation stability and various topics in ground control.

Jan 1, 1989

By David Gatto, Nicolas A. Willig-Friedrich, Jeff A. Segar

"With the increasing demand for electricity, and requirements to generate this power cleanly, more producers are turning towards hydroelectric power. A project in Iowa currently under construction will retrofit an existing Army Corps of Engineers Dam with a hydroelectric generating facility. The design of the intake structure requires the construction of a diaphragm retaining wall. The T-shaped diaphragm wall elements retain an unbalanced fill height up to 21.3 meters (70 feet). The design required a single production element be constructed, tested, and instrumented prior to beginning construction of the rest of the elements. The testing included extensive concrete mix design development, coring, and Cross Hole Sonic Logging. Installed in the other production elements are 10 inclinometers, 4 pressure cells, 4 piezometers, and multiple survey monuments. Some of these instruments require manual readings while most are monitored by an automatic data acquisition system and instantly transferred to a website providing real-time graphical display of the data. This paper will discuss the construction of the diaphragm wall from the contractor’s perspective when working on a site only large enough for two service cranes and a Hydromill excavation unit, without any storage area on the construction pad, describe the testing performed and the quality control procedures employed, and investigate the information gained from the automated instruments providing real time measurement readings.INTRODUCTIONIn 1964 the US Army Corps of Engineers (USACE) constructed a dam by raising the surface grade approximately 34.7 meters (114 feet) above the natural ground line using a combination of fill types. This earthen dam stretched slightly longer than a mile intersecting the flow of the existing Des Moines River. The center of the dam is a concrete spillway consisting of 12 monolith sections. On each end, three of the sections extend 42.6 meters (140 feet) from the spillway to transition from the concrete dam sections to the earthen dam section. Adjacent to these three sections on the East end is where the contractor is actively working, for a private developer under a lease agreement with USACE, on this site to convert it to a Hydroelectric facility licensed for an output of 36.4 megawatts, enough power to meet the needs of about 18,000 homes. To create this, a powerhouse structure, housing two vertical Kaplan turbines is being added to the downstream side of the existing dam. From the power house, two penstock pipes will be cored through the existing concrete monolith sections and connect to the Intake structure on the upstream side of the dam. Protecting and reinforcing the dam adjacent to the intake structure is a new diaphragm wall. This wall is constructed using T-shaped diaphragm elements, acting as a cantilever retaining wall for the intake platform. Figure 1 shows a diagram of the upstream features of the construction."

Jan 1, 2016

By J. Kempken, T. A. Schreiter, R. Degel, H. Schmieden

Keywords: Pyrometallurgy, SMS Demag, Germany, submerged arc furnace, ferro alloys, non-ferrous, FeCr, FeNi, FeMn, copper, cobalt, slag cleaning, PGM, rectangular furnace After a short summary of the SMS Metallurgy part of the SMS group, the paper will focus on Submerged Arc furnace technology. After general aspects of furnace design, the focus will shift to different applications and their specific furnace requirements. Finally, a state-of-the-art design tool as well as a new invention to improve slag-cleaning technology will be featured.

Jan 1, 2006

By I. M. London, G. P. Hatch

The Canadian Rare Earth Elements Network (CREEN) was formally launched at the Rare Earth Symposium at The Metallurgy and Materials Society of CIM (MetSoc) Conference of Metallurgists in October 2013. CREEN is an industry-led, multi-stakeholder network focused on providing collaborative solutions that will advance Canada’s REE sector to produce a significant proportion of the global production of separated critical rare earth products by 2018. The Network is industry driven by companies with REE projects under development and supported by universities, engineering firms, national and commercial laboratories, and government. CREEN aims to accelerate the development and delivery of timely solutions to technical and economic issues specifically facing Canada’s emerging rare earth sector. It will facilitate partnerships with other national and international organizations to leverage existing research initiatives. It will also support training and education to ensure that the needed qualified human resources are available to achieve the sector’s goals. CREEN membership spans the full rare earth supply chain and technical support organizations, from prospective producers, advanced project developers, national and commercial laboratories, engineering consultants, university researchers, and other innovators. This paper provides an update on CREEN's developing networking and project develop

Jan 1, 2014

By G. Bee, Z. Gavelan, R. Espinel, Y. Roditis, X. Ochoa

In August 1996 Barrick Gold Corporation acquired the Pierina property, an advanced stage exploration project, high in the Andean Cordillera of Peru and in November 1998, in a record time of just over two years, poured the first gold. After more than three years of a very successful operation at some of the lowest operating costs in the world, this presentation serves to briefly describe the project through design, construction and start-up and in particular to spotlight some of the challenges that have been overcome in valley heap leaching in a high rainfall, alpine setting.

Jan 1, 2002

The Gippsland Basin, southeastern Australia, has an Upper Cainozoic history of episodic change of hydrology and the related environment, reflected in the geomorphology and surficial deposits of the onshore basin and the hydrodynamically controlled accumulations of petroleum of the offshore basin. Succeeding this episodic pattern, man through a number of activities, has had a sudden and major impact on the hydrology and the related environment. Activities include those directly affecting the groundwater system, such as extraction of fossil fuels with the consequent threat of land subsidence; irrigation and clearing of vegetation and the consequent effect of salinisation; change of land use and installation of septic tanks with resulting nitrate pollution; damming of streams and the consequent reduction in the frequency of floods with degradation of the biological Environment; de-snagging streams and construction of cutoffs with increased stream erosion, modifying wetlands including drainage, with the consequent degradation of their ecosystems; and increase in phosphate and nitrate inputs to the coastal lakes with the risk of their eutrophication.

Jan 1, 1992

By Joshua Taylor Drake

This report answers specific questions concerning underwater blasting considerations, and blasting safety. The blasting considerations discussed consist of basic blasting principles, and new variables to be accounted for. Blasting safety will include the safety of personnel and structures. The environmental considerations will also be discussed with mitigation methods. To be most effective, this document requires the reader to be familiar with key fundamentals of explosive engineering. In order for a blasting professional to benefit from this report, the following questions will be asked:

Jan 1, 2015

By B Stump

Reliable particle size analysis in minerals processing plants is a critical factor to the economic return of a plant. As recovery of valuable minerals is compromised for particles outside the optimal size range, effective and reliable particle size analysis is more crucial than ever, particularly in the current upswing of the global commodities market. Inefficient particle size analysis can lead to excessive over-grinding, thereby significantly increasing energy consumption and reagent costs, whilst negatively affecting process operation, thickening capacity, water recovery and tailings disposal.Australia’s first installation of a particle size analyser in Iron Ore has been monitored with great interest by the industry. Previously, manual size sampling at Rio Tinto’s Paraburdoo fines processing plant involved off-site sample analysis, with a turnaround measured in days. The Outotec PSI® 500 particle size indicator, commissioned in July 2009, takes approximately three minutes per line at site.The paper will include details on the following:• plant description,• sampling design,• PSI® 500 analyser functionality description, and• key learnings from site.

Jul 11, 2011

By Hannan J. C

In New South Wales, development applications for major coal mining proposals are determined by the Minister for Planning and Environment and applications for mining leases and other mineral titles are dealt with by the Minister for Mineral Resources. The environmental conditions placed on the development consent, the coal mining lease and the approvals and licences under the pollution control legislation, amount to a substantial component of any new project's planning and commissioning considerations.An outline is presented of the framework within which various approvals are granted and conditions for environmental management are imposed upon mining projects. The principles and concerns, as perceived by the regulatory authorities, on which the majority of approval conditions are based are also outlined.No attempt has been made to analyse the extent to which these principles or standards are achieved in practice, nor to discuss the degree to which some of the conditions are achievable with the current status of technology and economics in the coal industry.

Jan 1, 1987

By C. Kenneth Eilerts

A method is described for controlling instability in finite-difference computations of liquid saturation near the borehole of a recovery well. Differences of pressure-and saturation-dependent variables are indexed offcenter, upstream and downstream alternately, to provide a stabilizing average. It was found that size of the time step could be increased by a factor of 4 without loss of numerical stability. Finite differences of the variables occur in a variety of relative numerical sizes and combinations. Those relationships of the differences that contribute to instability may be identified by the computing program in which they occur and modified to assist convergence of the computations and execution of the partial differential equations of liquid and gas flow.

Jan 1, 1971

By M. B. Kime

"Discrete-element method (DEM) modelling is a powerful tool for studying particulate systems within the mineral processing industry. DEM simulations were conducted to investigate the power draw, load behaviour, and impact energy profile of an experimental ball mill under different milling conditions. The variables considered were mill rotational speed (percent critical speed), ball size, and lifter face angle. The simulation results indicated that the grinding efficiency would be enhanced by using 80% critical speed, 30 mm ball diameter, and 45° lifter face angle. These findings can be useful in guiding actual ball milling tests involving an ore sample.RÉSUMÉ La modélisation par méthode des éléments distincts (MED) est un outil puissant qui permet d’étudier les systèmes particulaires au sein de l’industrie de traitement des minerais. Des simulations par MED ont été menées de façon à étudier le profil de la consommation énergétique, du comportement de la charge et de l’énergie de rupture d’un broyeur à boulets expérimental dans diverses conditions de broyage. Parmi les variables prises en compte figuraient la vitesse de rotation du broyeur (vitesse critique en pourcentage), la taille des boulets et l’angle de coupe de la cornière élévatrice. D’après les résultats de la simulation, on pourrait améliorer l’efficacité de broyage en utilisant une vitesse critique de 80 %, un diamètre de boulet de 30 mm et un angle de coupe de 45 ° de la cornière élévatrice. Ces résultats peuvent se révéler utiles pour les essais concrets de broyage à boulets impliquant un échantillon de minerai.INTRODUCTIONComminution is a very energy intensive process. It consumes approximately 5% of the electricity produced worldwide and more than 50% of the total energy used in mineral processing plants (Pokrajcic, 2010). Among all the comminution stages, ball milling is one of the most energy intensive processes. In ball mills, rotational movement provides the rise of the load and the media that are projected and impact on the mill shell at lower angular displacement, resulting in particle breakage. Ball mills are able to reduce particle size over a relatively wide range of particle sizes. This explains their wide applicability in research laboratories and the mineral processing industry."

Jan 1, 2017

By Emad Farouz, Ehab S. Shatnawi

"The increasing demand for small deformations and high-capacity drilled shafts without enlarging drilledshaft diameters has motivated the development and increasing use of a base grouting (BG) technique. This technique has been demonstrated to improve drilled-shaft capacity, especially for shafts tipped into loose cohesionless soils. Nevertheless, there remains considerable uncertainty in predicting the performance of base-grouted shafts, particularly for shafts tipped into cohesive soils. To date, there are only two documented design methods for estimating the axial geotechnical resistance of base-grouted shafts: Tip Capacity Multiplier (TCM) and Axial Capacity Multiplier (ACM) methods. A comprehensive test program was carried out during the design phase of the Wisconsin Zoo Interchange project to help optimize the flyover ramp’s foundation design. The test program included installing and testing one base grouted shaft and one ungrouted shaft at two sites with different ground conditions. Based on test results, it was concluded that prediction of the TCM method is well correlated with the measured values for both cohesive and granular soils; however, both methods tend to underestimate the axial resistance. Results also highlighted the importance of the base-grouting criteria in taking full advantage of the base grouting.INTRODUCTIONBase-grouted drilled shafts (BGDS), also known as post-grouted drilled shafts, consist of conventionally installed drilled shafts that contain access grout tubes placed within the shaft during construction. After installing the drilled shaft and achieving the pre-established concrete strength, grout is injected at the shaft tip through the access grout tubes to improve soil behavior around the drilled-shaft base. The tip grout injection improves the overall shaft capacity and reduces settlement through Densifying the in situ soils, compressing any debris left by the drilling process, preloading the soil beneath the tip to mobilize the shaft base resistance within service limits, increasing the tip area, and increasing the side resistance in the lower portion of the shaft."

Jan 1, 2016

By Reinhard Gertl, Maximilian Weithaler, Harald Kammerer, Juan Pablo Muñoz, Juan-Carlos Rueda

The Guillermo Gaviria Echeverri tunnel and its access roads project in Antioquia, Colombia is a mega infrastructure project that includes a road network with the longest tunnel in Latin America and several short tunnels, the latter being the focus of this study. The design of the project required careful consideration of several special factors, such as the tunnels’ steep slopes of up to 5%, high fire load of 100 MW, bidirectional operation, and short lengths that make it difficult to place ventilation equipment. The combination of all these parameters cause a challenging design problem for the ventilation systems and smoke control of the short tunnels. To address this challenge, a risk assessment study was conducted to support the design of a new and innovative ventilation strategy that deviates from relevant guidelines and standards, like the Austrian RVS [1][5][6] or the German EABT [8] in order to provide a customized solution for this particular project. This strategy resulted a cost-effective solution, that allowed a reduction in the number of required jet fans and at the same time reaches or reduces the risk level compared to traditional ventilation strategies.

Jun 13, 2023

By A. R. Hollbach

This paper presents a succinct overview of the Canadian coal situation. The topics treated specifically are: the rates of growth of coal supply and demand; the relationship between the coal and electricity generation industries which form its dominant market; the unique impact of nuclear generation on coal demand in Canada; and finally, a view of the developing technologies which will create opportunities for growth in the coal industry of the future. Resources The most important element of coal supply is the resource. The disposition of Canada's coal resources has a marked effect on their utilization, since industry in Canada has not generally developed around coal-fields. The distance from the major industrial centres of Ontario and Quebec to the major region of coal supply in Alberta and British Columbia has crested an economic barrier to the expansion of the use of domestic coal.

Jan 1, 1985

By T. R. Jolley

This publication describes the control of fires in inactive coal deposits in the Western United States, including Alaska by the Bureau of Mines. Material presented should contribute to a better understanding of the purpose, process, and benefits of the program. Forty fires were extinguished or controlled in the Western United States and Alaska from 1948 to 1958 under a national program directed by the Bureau's Health and Safety activity. Thirty-five fires were controlled by smothering; three were controlled by the isolation method; and two were extinguished by removing the burning coal, smothering it with incombustible material, and backfilling the fire zone. The fire-control projects were distributed as follows: Alaska 2, Arizona 1, Colorado 9, Montana 9, New Mexico 4, Utah 2, and Wyoming 13. The total cost of the 40 fires extinguished or controlled was $1,203,957. Of this cost, 12.8 percent was engineering and administrative and 87.2 percent was contractual services.

Jan 1, 1959

By S Vink, A Wolhuter

Increasingly the community and government regulators are calling for æzero dischargeÆ mines. Some mining companies are beginning to explore ways in which they can transition to zero discharge. When striving to attain zero discharge, mines must consider multiple variables in addition to water quantity. These include climate regime, water quality and regional water budgets. This paper explores the drivers behind the concept of zero discharge mines and will use examples to illustrate the feasibility of attaining this goal.CITATION:Wolhuter, A and Vink, S, 2013. Is zero discharge a viable or useful concept in mine water management?, in Proceedings Water in Mining 2013 , pp 329-334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By T. H. Chan

As the University of Hong Kong and their advisors planned their new Centennial Campus it became clear that they would have to re-provide existing water reservoirs on an adjacent site with new salt water reservoirs located underground in two new caverns. The existing reservoirs are owned by the Water Supplies Department who provide salt water for sanitary flushing and a separate potable water supply for regular use. Although underground reservoirs had not previously been adopted locally, the planning has been completed to a tight schedule and the construction is well advanced. The need to preserve historic buildings imposed constraints, as did the requirement to minimise potential construction nuisance for the local community and environment. This paper presents the background to the project and the work carried out to develop an innovative, sustainable and environmental acceptable solution. Construction progress to date is also presented.

By Reza Kamali, Mohsen Bashiri, Hadi Fanisalek

"Half of the input energy to aluminum reduction cell will be lost as waste heat which could be studied for possible recovery. Since price of energy is increasing and the main production cost in primary aluminum industry is energy, so waste heat recovery consideration will be interesting. One of the possible choices for recovering is from aluminum exhaust gases that needs minimum modifications for reduction cell and has no influence on cell heat balance which is vital for the operation. By using heat exchangers with in-line and staggered tube arrangements which placed before fume treatment plant (FTP) we will be able to recover enough amount of heat. The main challenging problem which is necessary to overcome will be the heat exchanger material and its design because of corrosive and dusty exhaust gases from potroom. In this paper, a desalination system with six effects of evaporator is proposed for producing distilled water by using recovered heat from hot exhaust gases. The calculated amount of produced distilled water is around 27,000 / in this specific suggested desalination plant. The suggested desalination plant is based on Hormozgan Aluminum Company data (Hormozal) in Bandar Abbas, Iran which is constructed by the Persian Gulf.IntroductionWaste heat losses arise both from equipment inefficiencies and from thermodynamic limitations on processes. The exact quantity of industrial waste heat is poorly quantified, but various studies have estimated that as much as 20 to 50% of industrial energy consumption is ultimately discharged as waste heat [1]. In order to achieve a final decision for establishing the waste heat recovery plant in any type of industry, a strong feasibility study is mandatory. Also, we need to remember that the possible amounts of energy and suggested process plant for recovery have to be investigated before starting any feasibility study. This kind of study which is important to be finished before moving to feasibility step is mainly a theoretical study, and was done for the Hormozgan Aluminum Company (Hormozal). In addition to the exhaust gases from the potroom, the exhaust gases from anode baking plant appear to have a better potential for waste heat recovery compared to potroom exhaust gases. The average temperature of exhaust gases from anode baking kiln is 120°C higher than the exhaust gases temperature in the potroom. This needs further investigation in a different study, because this study is just focusing on potroom exhaust gases."

Jan 1, 2011

By Joseph M. Pugliese

The U.S. Bureau of Mines has produced a generic in situ copper mine design manual, which contains a computerized cost model for in situ copper oxide mining. The model specifies (1) site-specific parameters, which must be quantified for mine design, (2) a method for minesite design based on those parameters, and (3) a procedure for assessing economic viability for the mine design. The menu-driven computer program performs calculations for developing commercial mine design specifications, as well as capital and operating costs. The default values are based on 1986 dollars, and indices for updating costs are included. The program also provides discounted-cash-flow rate of return (DCFROR) and allows for sensitivity analyses for an in situ mining operation at any specific undisturbed copper oxide deposit. This report is to be used with the 1990 version of the computer program, which has been made user friendly. It describes the flies, tutorial, input phase, help function, and monitor display of all calculated values and of the DCFROR table. The monitor-displayed discounted initial value of investment and annual operating costs are defined. The dual rate-of-return situation and sensitivity analyses are also briefly discussed. Information is provided on obtaining the computer program on diskette.

Jan 1, 1991