Search Documents

By George S. Dulikravich

An advanced semi-stochastic algorithm for constrained multi-objective optimization has been adapted and combined with experimental testing and verification to determine optimum concentrations of aJ10ying elements in heat-resistant and corrosion-resistant H-Series austenitic stainless steel alloys. The objective was to simultaneously maximize a number of alloy's mechanical properties. This research will result in a rigorous tool for the design of high-strength H-Series steels and other types of alloys unattainable by any means existing at the present time. Such a material-by-design tool will also be able to reduce or minimize the need for the addition of expensive elements such as Cr, Ni, Co, Nb, Ti, V, etc. and still obtain the optimum properties of an aJ1oy.

Jan 1, 2003

By R. J. Gunderman

Redesigns of the operator compartments on a continuous miner and on a face haulage vehicle are described. The objective was to optimize the compartments within limitations of existing equipment and functional configurations. Both safety and production should be improved through more comfort for the operator and more natural placement of controls. Design guidelines supplied by the Bureau from a previous contract were used along with human factors analyses to determine requirements. Mock-ups were fabricated from layouts and used to refine design details. The new compartments were implemented and the machines evaluated underground. Comments and reactions to both machines were favorable.

Jan 1, 1978

"There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, so, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the elements, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of adhearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco.Magnesite cement stucco should be applied in two coats, each 1/4"" thick on various surfaces such as wood lath, metal lath, sheathing board, brick, hollow tile, or stone; care being taken as regards the presence of lime, unless the same has been rendered, or become inert as with very old, walls. The first coat made up to a consistency that works easily under the trowel is applied in the usual manner. No water should be added to the liquid chloride as it would alter its density, and injure the work. The second or finishing coat is then applied. The aggregates are different in each, and no other dry material should be added to them as they come to the trade. The cement may be applied in zero weather without damage. Setting is quite slow under such conditions, but the cement ultimately becomes hard. It should always be applied to a dry surface excepting that under certain conditions it is desirable to apply a solution of magnesium chloride before using the stucco."

Dec 1, 1919

By Chris M. Healey

"Abstract- The Jasper Gold mine in northern Saskatchewan produced a total mill feed of 140 127 tonnes at an average grade of 19.0 g/t Au. Both diamond drilling and chip samples from under­ ground workings returned extremely high values, up to 12 851 g/t (375 oz/I) Au over 0.10 meter from a chip sample. In the presence of such extremely high grades, the accurate estimation of reserves is a major problem.ln the first part of this study, production data from the mine were used to evaluate the results of a variety of reserve estimation techniques in this environment. In two out of three cases studied, indicator kriging with assays cut to 342.9 g/t (10 oz/I) gave extremely good results. In the third case, however , indicator kriging gave unacceptable results. Instead, lognormal kriging of uncut data gave the best results.Secondly, from the same database, a number of drill-hole spacings were simulated, and reserves estimated from the simulations. As may be expected, the results of this analysis show increasingly better results with tighter drill-hole spacing. However, even with a 5 m by 5 m spacing the variation from actual grade was quite large. This is not a systematic under- or over-estimation of grade, rather a random scatter of results .The results of this study show very clearly the problems of deriving good estimates of reserves when extremely high-grade samples are encountered. There is a high degree of randomness to this database, so reserve estimation in this situation will remain a high-risk operation."

Jan 1, 1993

By A. R. MacLean

This mine is situated at Point Aconi, Cape Breton , Nova Scotia, and is a replacement for the 100-year-old Princess Collie ry. It is a slope mine which is the continuation of a s trip mine operation. There are fives lopes from the surface driven with Dosco Dintheaders - this marks the first time these machines were used in North America. There are four room -and-pillar sections, each equipped with a Lee Norse HH106 continuous miner, a "Top Dog" roof bolter and two Wagner diesel Teletrams. There are also two Eimco 913 diesel LHD's , which are used for clean-up in the mines. This paper describes the mining operations of this 800,000-tpy mine which, in less than a year and a half , has been developed to the stage where four sections are producing coal at the desired rate.

Jan 1, 1978

By P. J. Yttrup

Small diameter timber piles are used in Australia to solve foundation problems in soft or filled ground and expansive soil. The paper describes the results of pile load tests to develop simple methods for bearing capacity determination and observation of the performance of piles in expansive soil.

Jan 1, 1989

By H M. Ahmed, W S. Dunbar

Construction of cave mining systems requires significant capital expenditure and long-term commitment of human, equipment and material resources before production commences. Risks and uncertainties of these large-scale mining projects are significantly higher than for small-scale projects. This is due to the complexity and interactions of the construction schedule components and the large scale and uniqueness of such projects. One way to successfully manage construction uncertainties that would lead to schedule delays is to include a reasonable cost contingency in the budget estimation. A real options approach based on the least-squares Monte Carlo (LSM) method is used to estimate cost contingency associated with schedule uncertainty in mass mining projects. Cost contingency is estimated as the cost of potential project crashing (acceleration) decisions, which pays for not extending the schedule. While such a significant undertaking is expected to be subject to some delays, these can have an enormous impact on the economic value of such projects. The value of the crashing option was explicitly formalised into the process of valuation, as it is assumed to be a single option being considered in the valuation at every decision point prior to the construction completion date. As a part of the proposed method, a stochastic function for the percentage of remaining scope of work for the remaining duration of the entire project was integrated into a framework of numerical simulations. This ensured that this function can implicitly account for sources of schedule uncertainties for projects represented by multiple and overlapping work packages. The LSM method was applied to a real case scenario in an operating block cave mine, with modified scale and features. The results yielded by the LSM method indicated that significant changes in capital budget allocation stem from variation in a contractor’s risk perception and confidence level of estimated delays.CITATION:Ahmed, H M and Dunbar, W S, 2016. Budget estimation and contingency allocation of block cave construction using least-squares Monte Carlo real options, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Graham Davis

The future of the world's minerals industries is often painted as bleak. Peter Drucker has repeatedly proposed that the demand for minerals has become "uncoupled" from world economic growth.' This implies that, while mineral demand was in the past linked to the growing demand for and consumption of goods and services, further world development will not require substantial mineral inputs. Lester Thurow noted that for these reasons the US minerals industry is diminishing in scale and economic importance.2 There is some documented evidence of such uncoupling, and the demand for minerals may indeed diminish in the future. But such announcements are, to this point, no more than speculation. For instance, is it not just as likely that renewed environmental concerns will cause increased demand for the relatively innocuous environmental properties of metals, replacing plastics? And even if the prophesied demand decreases do occur, a sufficient fall in metal prices due to technological advances could increase the quantity of minerals demanded above current levels, in spite of leftward shifting demand curves. Thus, worldwide mineral production activity may increase or decrease in the future and no one can say whether more or fewer of the earth's citizens will become involved in the extraction and processing of minerals.

Jan 1, 1994

By Kelly E. G

NZ Steel's flushing slag typically contains 1.2 per cent V203. Extraction of vanadium from powdered slag using a salt (NaCI or Na2CO3) roast/leach process was investigated. With NaCl, optimum extraction conditions were a charge containing 10 per cent NaCI, roasting in air at 875°C for 4 hours, followed by leaching in dilute H2SO4. Extractions were typically 30-50 per cent. NaCI roasting did not chemically attack the slag; the phase transformations that occurred were due to high temperature oxidation. Slag particle size had a significant effect on extraction.Optimum conditions for extracting vanadium by Na2C03 roasting were 20 per cent Na2CO3 in the charge and roasting in air for 3-4 hours at 850-875°C followed by water leaching.Na2CO3 roasting involved chemical attack that resulted in the formation of perovskite (CaTiO3) and carnegieite (NaAISiO4).The extent of vanadium extraction depended on the amount of Na2CO3 added and the original slag SiO2 content.Compared to the separate roasting treatments, simultaneous treatment with NaCI and Na2CO3 gave lower vanadium extraction, while requiring considerably higher roasting times and temperatures.

Jan 1, 1982

By Donald F. Reed

The bauxite deposits of Tippah and Benton Counties in northeastern Mississippi were developed by drilling as a part of the investigation by the Bureau of Mines of the domestic sources of supply of aluminum. The primary purpose of investigations of this nature was to provide essential information to the war agencies of the United States Government and to assist owners and operators of mining properties in the production of minerals vital to the prosecution of the war. These reports are based upon the field work of the Bureau of Mines and upon data made available to the Department from other

Jan 1, 1948

By W. H. Bassett, C. H. Davis

The late J. P. Sparrow, chief operating engineer of the New York Edison CO., carried out a series of practical tests on condenser tubes of several copper alloys and reported on the results to the Association of Edison Illuminating Companies at its meeting in September, 1913. In the preparation of these tubes the senior author had the pleasure of cooperating. Copper-zinc alloys in the proportions of 60-40,70-30,80-20, 90-10, and Admiralty metal, which is in effect 70-30 with 1 per cent. of tin, were tried. Monel metal and several copper-nickel alloys, and 8, 5, and 3 per cent. aluminum bronze were also tried. At the time of this report, the aluminum bronze had been in service for 4 1/2 years and seemed to be giving especially good results but later it began to fail and showed no substantial improvement over Admiralty metal. Monel metal was unsatisfactory and the nickel alloys apparently did not give better service than the Admiralty alloy. Previous to the publication of the report, and after considerable discussion, it was agreed that a test where tubes of different kinds could be under laboratory observation would be advisable, so the apparatus described here was set up in The American Brass Co.'s Waterbury Laboratory. This was fitted with tubes of copper, brass, bronze, nickel silver, cupro-nickel and other alloys, and the test started on Oct. 11, 1912. Salt water from East River, New York harbor, was barrelled and transported to the laboratory for the test. A fresh supply, completely replacing the water in service, was obtained at the end of each six months period. Plan of Procedure In general, the procedure was to inspect the tubes at short intervals and to remove those that had begun to leak. The tubes removed were carefully examined and a photographic and microscopic record of the

Jan 1, 1925

By A. J. Thompson

The Metropolitan Transportation Authority (MTA) East Side Access project (ESA) will, when it is complete, provide a new link to the east side of Manhattan from Long Island, NY that, linked with the Second Ave. Subway currently under construction, will assist in relieving overcrowding at Penn Station as well as the Lexington Ave. subway. ESA will bring Long Island Railroad (LIRR) directly from Long Island into a new station located 37 m (120 ft) beneath the existing Grand Central Terminal (GCT) located in the heart of Manhattan. It will connect the LIRR?s mainline tracks in Queens, via the existing 63rd Street Tunnel under the East River, to a new terminal constructed within, and beneath, the historic Grand Central Terminal.

Jan 1, 2012

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant, it was critical to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. Various compaction parameters were verified and established on a small laboratory-scale compaction machine to obtain a coal cake of acceptable stability. These parameters include cake density, cake surface moisture, transverse strength (force applied perpendicular to the original compacted coal cake layers), and applied force to the coal cake. This work determined the behavioural characteristics of the coal while being compacted either with a full-sized or a 1/3-sized compaction plate in a 9 kg capacity mould. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.The target wet cake density of 1 100 kg/m3 (79% of 1 400 kg/m3 relative density) was achieved for Waterberg sscc, with a particle size d50 varying between 0.6 mm and 1 mm, utilizing the 1/3-sized compaction plate in the laboratory-scale set-up, with 11.6% surface moisture and 92.2 t/m2 commercial equivalent applied force. For Oaky North hard coking coal, a wet cake density of 1 189 kg/m3 (85% of 1 400 kg/m3 relative density) was achieved at a surface moisture content of 12.3% and at a lower applied force than that for Waterberg sscc, i.e. 78.5 t/m2.Coal cakes of acceptable strength, and therefore sufficient stability for further processing, were obtained for all materials evaluated during this study.Further studies should be conducted to determine the effect of zeta potential during the compaction of coals.IntroductionExxaro Resources has successfully installed and commissioned a world-class stamp-charging horizontal 1 t electrically-heated pilot-scale coke oven at its Metallurgy Services facility. Prior to operating the coke non-recovery pilot plant, it is essential to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. The design of Exxaro’s pilot plant is such that the coal cake is pushed inside the oven by means of a pusher plate, rather than through a ‘spoon’ feed mechanism, such as is found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength during loading into the oven, owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability, various compaction parameters needed to be verified and established on a small laboratory-scale compaction machine."

Apr 1, 2019

During the past three years Lurgi's Circulating Fluid Bed (CFB) technology has been successfully applied to roasting of refractory gold ores and con- centrates. In comparison with the so-called Stationary Fluid Bed roasting systems, a considerable improvement of gold recovery, to around 95 per cent, has been demonstrated and achieved on many occasions in pilot CFB units and in commercial CFB roasting plants as well. The major reason for such improved gold recoveries is the excellent controllability of the roasting process in the CFB reactor system. Here, temperature, gas atmosphere and solids residence time are more precisely controllable at optimal values during roasting operation in order to achieve the highest possible gold recovery in the subsequent leaching process step. Further dominant benefits of CFB roasting systems are their flexibility with regard to feed material, throughput capacity, dry or slurry feed, almost unlimited oxygen enrichment, direct fuel addition and in situ capture of SO2 in the presence of limestone and dolomite. The system will accept 50 per cent turndown ratio, large variations in feed composition and particle size, as well as a variety of different fuel types. The commercial applications of CFB roasting systems for gold con- centrates have been realized so far at Fimiston, Kalgoorlie/Westem Australia and for whole ores at Cortez, Nevada/USA.

Jan 1, 1991

By Donald A. Bruce

The paper reviews aspects of the construction and performance of prestressed ground anchors installed in soils and weak rocks. Attention is focused on good practice for drilling, tendon fabrication and handling, grouting, stressing and testing. Regional variations - not always logically justified - are described. The performance of anchors in a variety of geological conditions is illustrated with reference to recent full scale test programs. 1. Introduction In the United States there has been steady growth in the use of prestressed anchors in materials other than competent or hard rock, in the years since their introduction in the late 1960's. This expansion has to a large extent been driven by specialty geotechnical contractors who both imported foreign developments and conducted their own basic researches, in locally prevailing conditions. With such data and experience, these engineers have had the confidence to promote "alternative solutions" for difficult earth support problems to receptive designers and owners. In turn, being engaged in the details of design and performance monitoring has given these parties the close exposure necessary for the real transfer and understanding of the technological concepts, and this knowledge has generated positive feedback for the contractors.

Jan 1, 1991

By Matt Bilson, Ritesh Mahajan, Antoni Kuras, Wataru Okada

The Waterview Tunnel comprises twin 2.4 km long 13.1 m internal diameter three lane road tunnels in Auckland, New Zealand. The City Rail Link (CRL) is a 3.45 km long, 6.24 m internal diameter twin rail tunnel underneath Auckland’s city center. This paper presents an overview of the tunnel geometry, segmental lining congurations, geometric constraints, performance criteria and functional reuirements for the large diameter Waterview Tunnels and smaller diameter CRL tunnels. Other key aspects, which include sustainability, innovations, construction performance and practical aspects are discussed and compared. Lessons learnt from these mega tunnelling projects are also presented.

Jun 23, 2024

By G J. Fleming

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within theAndaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra. Miwah mineralisation is associated with variably dipping structurally and lithologically controlled argillic and advanced argillic alteration. An oxidised supergene leached zone and a recent, thin, unaltered tuff blanket partly overlie the mineralisation. Mineralised zones are commonly brecciated and veined, and display quartz, quartz-alunite, quartz-alunite¦pyrophyllite¦kaolinite replacement assemblages, surrounded by more weakly mineralised, often vugghy quartzalunite¦pyrophyllite¦kaolinite advanced argillic, and argillic zones of quartz-kaolinite, quartz¦pyrophyllite¦kaolinite and smectite-illite-quartz. Propylitic assemblages are marginal to more intensely altered zones. Hypogene copper mineralisation is typified by enargite, luzonite, and covellite. The host mineral to gold is uncertain at present. Rare barite, native sulfur, and ?telluride also occur. Bornite and chalcopyrite have been observed in transported altered rocks in faults. Generally the mineralisation is anomalous in precious metals, locally enriched in Cu, erratic in Pb, and depleted in Zn, with a good correlation between Cu-As-Ag.

Jan 1, 1995

By M. C. Manderson

Phosphate rock is a naturally occurring mineral which, in upgraded form, is important to both agriculture and industry. Phosphate rock normally must be upgraded before it can be assimilated and used. Most of this upgrading is now carried out by chemical means, largely through the reaction of a strong inorganic acid (primarily sulfuric acid) with the phosphate rock to remove major impurities and to produce soluble phosphate. A less important but yet still commercially significant conversion method involves the thermal reduction of phosphate rock at high temperature in an electric furnace to produce elemental phosphorus. The elemental phosphorus is then converted to usable end products. This conversion route is a more costly method than the chemical route, but it has the advantage of being able to produce chemically pure phosphorus derivatives. On the other hand, the use of phosphate rock for agricultural application-primarily for use as a plant nutrient ingredient for fertilizer -does not require the same level of purity. As a consequence, the chemical method of phosphate rock upgrading is the predominant technique for producing phosphatic fertilizers.

Jan 1, 1977

By Luis Martín Tejada

Para la evaluación de la estabilidad de taludes en minería superficial se utilizan diferentes métodos de modelamiento y planeamiento como el de simulación numérica. En ese sentido, el presente texto describe el método de tensión-deformación, cuyo base se encuentra en el método numérico de elementos finitos, y así localizar la probable superficie de ruptura. También se describe los mecanismos de ruptura en taludes altos, el cálculo del FS y algunas características del programa de elementos finitos PLAXIS.

Sep 9, 2007

By W Farnworth

The Huntly West Mine has undergone significant changes in the last two years, which will affect the remainder of the mine's life. The paper describes the evolvement of plans and an overview of the technical considerations made in planning for and implementing the first New Zealand longwall operation. The technical investigations involve the longwall equipment, exploration, ventilation and strata control. The focus on these areas was to ensure that unacceptable project risks were addressed. Implementation of longwall mining at West Mine is planned in three phases, Development, Panel One extraction trial, and Full Longwall operation.   At present the development phase is complete, longwall installation is in progress and production start-up is planned for the end of August, 1991.

Jan 1, 1991