Search Documents

By D. C. Hilty, W. Crafts

J. Chipman—It has been my privilege to discuss this work with the authors on several occasions and to observe at first hand the experimental methods employed. I wish, therefore, to emphasize certain points which they have mentioned only briefly with regard to the experimental techniques. The rotating induction furnace as here employed interposes liquid metal between slag and refractory thus preventing the two nonmetallic parts of the system from reaching equilibrium with one another. It is therefore impossible for the metallic phase to be completely in equilibrium with both the slag and the crucible. The metal also acts as a partially permeable membrane allowing certain components, including oxygen, to diffuse from slag to crucible. This transfer results in building up on the face of the crucible a layer of material whose composition is in part dependent on that of the bath. Reactions between the layer and the solid refractory are slow, as evidenced by the rather good life of the crucible. Hence it seems probable that the layer is more nearly in equilibrium with the metal than with the underlying crucible material and that, once it is established under a bath of a given composition, its further reactions with that bath are slow. Additions to slag or bath may be followed by changes in the layer; and time must be allowed for virtual completion of such changes, before it can be assumed that slag and metal are in equilibrium. We may judge from the results reported that, in general, this was the case and that the data represent at least quite close approximations to slag-metal equilibrium. Data on deoxidation and on oxygen solubility are no better than the analytical methods employed. The vacuum fusion method as used by the authors seems entirely adequate for the samples analyzed. I have had frequent occasion to compare results with their laboratory, always with very satisfactory agreement. The determination of aluminum at very low concentrations is perhaps an even more difficult procedure. Here also the colorimetric method used has been worked out with great care and is undoubtedly the most dependable method available. The discrepancy between observed and calculated deoxidation or solubility lines is not to be explained as the result of experimental errors, either in the sampling or analysis of the metal. Nor is it to be blamed upon inaccuracies in the several kinds of indirect data upon which the calculated results were based. It is true that both the observed and the calculated lines admit of some uncertainty as to their exact locations, but the uncertainties are small compared to the wide gap which separates the two lines. The authors have pointed out the real cause of the discrepancy. In all of their experiments the solid phase was not Al2O3 but a mixed oxide containing iron and aluminum. This suggests an extension of the calculated values to include equilibrium with the spinel FeO . A12O3. The free energies of FeO and A12O3 are known, that of the spinel is not. However, it cannot differ greatly from that of its component oxides for even in the more stable spinel, chromite, the free energy of formation from the oxides is less than 10,000 cal. For purposes of calculation we shall call this free energy X and solve for values of X lying between zero and 10,000 cal. The other data required are taken from the forthcoming revision of "Basic Open Hearth Steelmaking" and are given in the following equations in which underlined symbols indicate elements dissolved in liquid steel and the standard concentrations are 1 pct. ?F° at 1600°C, cal ?LA = 2 Al + 3 O; + 107,200 FeO = Fe + 0; + 5,460 FeO + A12O3 = Fe + 2A1 + 4 0; + 112,660 — X The corresponding equilibrium concentrations are shown in fig. 21. The line marked A12O3 corresponds to the first equation, those marked FeO . AL2O3 correspond to the last, with X = 0, 5000 and 10,000 cal, respectively. The two upper lines represent the data of Hilty and Crafts and of Wentrup and Hieber. The points are the observations of Hilty and Crafts in the presence of 0.50 pct Mn.

Jan 1, 1951

What is a conflict, as it is understood by men of the extractive industries? And what are the circumstances out of which these conflicts arise? A start can be made with the notion of economic conflict, which can be defined as rivalry over the use of economic resources. Such rivalry is a central part of all economizing activity. It is present within the individual, within the family, and within the business firm. In each of these units there are multiple goals competing for use of a limited income. And economic rivalry is present among individuals and firms who are competing with one another for use of the limited quantity of economic resources available to us as a society.

Jan 7, 1961

By Vernon A. Mrak

The Powder River Basin of northeast Wyoming was the first area in the state to receive attention during the early days of uranium exploration. Although the uranium occurrences are many and widespread, most of the known ore deposits are quite small and difficult to mine. As a result of this, detailed regional exploration in the Powder River Basin has been neglected. The uranium ore deposits occur in that part of the Wasatch Formation that is of earliest Eocene age, and they are scattered over an area of about 400 square miles. All uranium ore deposits are associated with red beds or altered sandstones within the Wasatch Formation. Uranium ore was first shipped from the region in 1953. Total production through June of 1965 is 506,257 tons of uranium ore containing 1,922,527 pounds of U3O8. The average grade of ore is about 0.19 per cent U3O8. The major producing area of the Powder River Basin is the Monument Hill district where about 91 per cent of the basin's total uranium ore has been mined. The source of uranium is presumed to have been the Oligocene, Miocene, and perhaps Pliocene tuffaceous rocks that once overlay the area. Joints, fractures, and permeable beds or zones were the passageways for the migration of uraniferous waters from the overlying beds to the Eocene host rocks.

Jan 1, 1968

By R. M. Waterstrat, E. C. van Reuth

BINARY- alloy phases having the A15-type crystal structure have been described as occurring at a simple and more or less invariant stoichiometric composition (A3B) which corresponds to the relative number of atoms occupying each of the two crystallographi lattice sites in this structure.1,2 It is frequently assumed, therefore, that each crystallographic site is occupied exclusively by one kind of atom. In most cases, however, there have been insufficient experimental data to establish whether atomic ordering is, in fact, complete. Recent studies have shown that binary A15-type phases are sometimes stable over an appreciable composition range3''* and, occasionally, the composition range of stability does not even include the "ideal" A3B stoichiometric composition.5-7 We have observed the existence of nonstoichiometric A15-type phases in the binary systems Cr-Pt and Cr-Os. This has not been reported in previous work on these alloy systems.1,8-11 A series of alloys, each weighing approximately 30 g, was prepared by are-melting in an Ar-He atmosphere using 99.999 pct Cr, 99.999 pct Os, and 99.99 pct Pt as starting materials. Each alloy was melted four times with a total weight loss of less than 1 pct. The stoichiometric (A3B) alloys were sealed in evacuated quartz tubes and annealed at 1200°C for periods of time ranging from 3 days to 2 months. Examination of the alloy microstructures revealed that little change had occurred over this time interval and it was therefore assumed that the microstructures were fairly representative of equilibrium conditions. No evidence of contamination was observed although there was apparently some loss of chromium which was confined to a thin layer at the surface of the specimens. The quartz tubes were quenched from the annealing temperature into cold water. X-ray diffraction and metallographic examination of the stoichiometric alloys revealed an estimated 10 to 30 pct of second phases which were tentatively identified as phases previously reported in these binary-alloy systems.8-11 A second series of alloys was prepared by mixing -325 mesh metal powders having a nominal purity of 99.9 pct and compressing these mixed powders in a cylindrical die at a pressure of 43,000 psi. These alloys, each weighing 15 g, and some of the arc-melted alloys were annealed in a high-temperature vacuum furnace heated by tantalum strips at a pressure of 10-8 Torr and were rapidly cooled by turning off the furnace power. X-ray and metallographic examination of both series of alloys served to establish the composition ranges of the A15-type phases. Although some chromium losses occurred during the vacuum annealing, they were largely confined to a thin layer on the outer surfaces of the samples. It was established that the A15 phases occur in the Cr-Pt system at 21 ± 1 at. pct Pt after 1 week at 1200°C and in the Cr-Os system at 28 ± 1 at. pctOs after 1 day at 1400°C (see Table I). We also observed that an arc-melted stoichiometric (A3B) alloy in the Cr-Ir system was single-phase (A15-type) in the "as-cast" condition in agreement with previous work.8,13 In addition we obtained a sample of the Cr-Os A15-type phase from Argonne National Laboratory. This alloy contained less than 1 pct second phase12 and was submitted to a density measurement. The density measurement yielded a value of 11.14 g per cu cm in comparison to a theoretical value of 11.25 g per cu cm calculated using the observed lattice constant (4.6806Å) of this alloy. The uncertainty in measurement was 0.1 pct but the sample may have contained some cracks or minor imperfections which could account for the low experimental value. We have also studied the atomic ordering in these phases by means of integrated line intensity measurements using thick, flat, rotating powder samples and CuK a radiation in an X-ray diffractometer. We have obtained order parameters of 0.90 for the Cr-Pt phase, 0.89 for the Cr-Ir phase, and 0.64 for the Cr-Os phase using the formula: where s is the usual Bragg and Williams order parameter, ra is the fraction of chromium atoms in A sites, and FA is the fraction of chromium atoms in the alloy. The values obtained are estimated to be accurate within ±4 pct. If the unusually small value for the order parameter of the Cr-Os A15 phase were due to the existence of lattice vacancies on the "B-atom" sites, then a density of 10.04 g per cu cm would be expected in contrast to the observed value of 11.14 g per cu cm. We, therefore. conclude that the fraction of lattice vacan-

Jan 1, 1967

By C. L. HUNTZINGER

THE mine here described is in the Witbank district, a coal area of the Transvaal, about 100 miles north- east of Johannesburg. and is owned by the Witbank Colliery, Ltd. The plant has a capacity of 4000 tons per eight hours, and prepares five sizes of coal. The coal seam lies at a depth of about 200 ft. below the surface, and is reached by an inclined shaft sunk at an angle of 18° with the horizontal. Although the thickness of the coal seam varies from 10 to 14 ft. or more, only about a 7-ft. bench is mined. Mining is by the hord and pillar system. Bords are driven 18 ft. wide, with pillars measuring 18 ft. square. The mine is laid out into four sections, each sewed by a main haulage way from the shaft. Arc-wall machines are used for cutting the coal. but all loading is done by hand. Native labor is employed under the supervision of white miners, who do the required blasting. The workings are practically free from gas and water, and very little timber is needed.

Jan 1, 1931

By J. P. Zannaras

Referring to the article by R. J. Charles and P. L. de Bruyn, let us assume that W = weight of glass bar; P = weight of hammer; e = total deformation; E = unit of deformation; K = potential stress energy; E = modulus of elasticity; L = length of the bar; 7, = coefficient of inertia; h = height, ft; V = velocity, fps; and a = cross section area. The portion of kinetic energy which is effective in producing stress energy in a fixed bar struck horizontally is given by the formula [ ]

Nov 1, 1956

By AIME AIME

FEW indeed are the sections of the country where trained or partly trained workers have not already been hired by a war industry plant or will be within the near future. Yet right in the midst of the heavily industrialized East lies the anthracite area, home of a million people, whose productive power has persistently been by-passed either by private industry or by the Government Plant Site Board. The chief reason given for not locating war plants in the area is that it is not within the strategic zone, but in numerous instances elsewhere this rule has been waived. Furthermore, the anthracite region is well protected on all sides by mountains and is at all points more than 100 miles inland. Continued depression in the anthracite industry and a crippling blow dealt by the war emergency to the production of silk and rayon goods, the chief manufacturing activity of the area, have resulted in a heavy migration, particularly of trained young workers, into near-by industrial areas. At least 50,000 people are currently unemployed, with the likelihood of an increase in coming months, and as many families are on relief.

Jan 1, 1942

By Charles W. Perry

The options of enhanced oil recovery, coal syncrude, and shale syncrude are compared by approximately equivalent economics. The physical constraints for the major enhanced oil recovery processes are described, followed by new estimates of cost. The range for all three options in terms of light syncrude equivalent are $22 to $40 per barrel in 1980 dollars.

Jan 1, 1982

By R. L. Brown, A. C. Fieldner

Committee it supports pioneering research on the development of a coal-burning gas turbine and through the Mining Development Committee it promotes research on a new type of continuous mining machine that operates without using explosives. Other organizations have contributed major publications on fundamental and applied coal research in the last two decades, including the Minerals Industries Experiment Station of Pennsylvania State College, the Illinois Geological Survey and University of Illinois, the University of West Virginia, the University of Michigan, the University of Alabama, the University of North Dakota, the Massachusetts Institute of Technology, the Koppers Company, the U. S. Bureau of Mines, and, in recent years, the Institute of Gas Technology. Engineering development work, which is included in the overall estimate of $20,000,000, is conducted largely by manufacturers of equipment, and this portion of the estimate is difficult to gage. It represents a large proportion of the estimate and probably is too small rather than too large. For example, the development of mobile coal-loading machines and continuous mining machines, outstanding in recent mining research, undoubtedly involved a high cost. Coal Mining From an economic point of view, the greatest research development in the coal industry obviously has been the growing degree of mechanization in mining. The percentage of underground-mined bituminous-coal output mechanically loaded has risen from 3 pct in 1926 to 67 pct in 1949. Coal operators and equipment , manufacturers have united in designing machinery. Loading machines of large capacity and astonishing flexibility are in common use. Shaking conveyors transport coal from producing faces to transfer points from which it may be carried long distances underground and on the surface; and in many mines rubber-tired shuttle cars carry the coal from the loader to the

Jan 1, 1952

By Kenneth R. Hancock

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after it has been pulverized to pigmentary size. The current world production of iron oxide pig¬ments is estimated by the author to be between 450,000 and 550,000 tons based on 1969 data. The fact that highly colored natural deposits of iron ore are found throughout the world ac¬counts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test fence which now has some 20,000 years of exposure. In addition to abundance, constituting about 7 % of the earth's crust, iron oxides have the advantages of low cost, permanency, and are not toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when coloring was desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments pro¬duced from natural iron ores in uniformity, color quality, and chemical purity. In the United States alone, the combined production of natural and synthetic iron oxides produced sales of over $28,000,000 in 1970 (Stipp, 1970). Nomenclature With the increasing importance of the syn¬thetic iron oxides it is necessary to make a distinction between the natural or mineral pig¬ments and the synthetic pigments. Natural pigments are those products which are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a com¬mercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pig¬ments. Natural pigment ore sources are se¬lected for their special physical-chemical prop¬erties and can command a premium price. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pig¬mentary sized particles are produced as opposed to comminution, the major procedure common to all natural iron oxide pigments.

Jan 1, 1975

By J. W. Ristori, V. R. Garfias

ONE of the most serious problems now confronting Gel- many-and one that will affect Italy even more seriously if she goes to war against England and France -is that of supplying her navy, mechanized army, and air force as well as her industrial and other needs with the necessary and related products. This problem, serious even now, will become vital should hostilities on a large scale develop.

Jan 1, 1939

By A. W. Ashbrook

The process of solvent extraction.(or liquid-liquid extraction) is a separation technique involving mass transfer across a phase boundary, and as such is not limited to metal transfer from an aqueous to a non-aqueous phase, or, vice versa. We shall here, however, restrict ourselves to the application of the solvent extraction technique to metallurgical processing. Basically, the process of solvent extraction as applied to metals separation and purification requires only that a specific metal be transferred from, initially, an aqueous phase to a non-aqueous phase, followed by a reversal of this transfer. Such a process can be defined simply by the following equation: [M + E ME]

Jan 1, 1978

By Herbert Hoover

YOUR committee asks that I speak today on the relations of the engineering profession to public affairs. That takes in a lot of ground. This being a cheerful occasion, I will assume that I should exclude the engineer's function as a taxpayer. This being a nonpartisan occasion, I will assume that I should not refer to his voting emotions in 1940. Perhaps what was in the minds of your committee was the application of engineering thought to the confusions of the times. That is also a lot of ground. I fear, however, its boundaries disappear in mirages and rainbows on all sides. Now any entry of the engineer into public affairs involves his breaking into the fields of the sociologists, the economists, and the politicians. However I don't know why, seeing the difficulties these professions are having, they should not welcome a little help.

Jan 1, 1939

By R. D. Parks

DESPITE the handicap of reduced production in many districts, the mining industry in 1938 forged steadily ahead toward solution of its minor technical problems and has of-defected major advances in several fields. In California hydraulic mining for gold, shut down for forty years, will shortly be resumed following revision of restrictive laws. Disposal of hydraulicked ground is to be regulated by settling dams so as not to interfere with agriculture. Gold mining has been aided also by the development of a new high-efficiency dry amalgamator which applies the Ramsay mercury separator to the original de Phily process. Based on the principle that crushed ore will follow a rod into a mercury bath, this simple device is primarily adapted to dry areas and is to be available in small, multiple units suitable

Jan 1, 1939

By T. A. Rickard

MILLING is one of the metallurgical arts whereby the extraction of the largest possible proportion of the value in an ore is effected at the least possible expense. Stamp-milling* is that particular process in which a heavy body of iron is caused to fall upon the ore so as to disintegrate it and thereby induce a separation between what is valuable and what is worthless. The latter is usually less in specific gravity, and is therefore, by the further aid of water, removed from the former, which is then collected by the use of mercury. Several similes have been employed to describe this process. The stamp has been likened to a hammer of which the stem is the handle and the die the anvil. The ore upon which the stamp falls has been compared to a nut awaiting the descent of the hammer whose blow is to separate the valueless shell, the quartz, from the valuable kernel, the gold. When we begin to pursue our inquiries, however, we find that the analogy is just sufficiently true to emphasize the departures from it. The hammer falls, the anvil is fixed; so with the stamps and the mortar. The anvil is made of softer metal than the hammer; so also the die is often, and should be always, of steel or iron less hard and more tough than that of the shoe. The movement of the hammer and the drop of the stamp are both intermittent. In regard to their intermittent action, as in many other respects, stamp-mills arrange themselves under two types, which, though apparently contradictory, have both been evolved from a common original, and are united by a great variety of intermediate modifications. The slow speed and the high drop of the mills of Gilpin county Colorado, appear to have very little in common with the fast speed and short drop of those of the main gold belt of California; yet the practice of the one was largely derived from that of the other,

Jan 1, 1894

By G. Nabi, W-K. Lu

Cylindrical specimens of natural dense hematite were reduced to magnetite at atmospheric pressure in H2-H2O mixtures of known composition over the temperature range 1084° to 1284°K. The rate of reduction was measured by the rate of movement of the interface between hematite and magnetite. The diffusion of gases through the gaseous boundary layer, the magnetite layer, and the interfacial chemical reaction were all considered in the interpretation of experimental data. The mass transfer coefficient through the boundary layer was calculated using accepted correlations. Values of the chemical reaction rate constant and the diffusivity of hydrogen in the magnetite phase were determined. THE present investigation is concerned with the reduction kinetics of natural hematite to magnetite by H2-H2O mixtures in the temperature range 1084" to 1284°K at atmospheric pressure. This reaction is the first step in the series of topochemical reactions in the process of reducing hematite to iron. Kinetic information of the simple steps such as hematite-magnetite transformation is necessary in order to have a better understanding of the complex processes of hematite reduction in iron-making. It also has direct industrial significance because magnetic roasting is one of the most important methods in benefication of lean ore.&apos; Although many technical papers have been published on the process of magnetic roasting and iron oxide reduction, very little information is available in the literature concerning the fundamental nature of hematite reduction to magnetite by reducing gases. Hansen et al.2 reduced the dense synthetic pellets of high-purity oxide in CO-CO2 mixtures and determined the reaction rate by weight-loss method. They were able to interpret most of their results by applying the interfacial area control theory developed by Mckewan.3 In contrast, Wilhelm and St. Pierre,4 who studied reduction of hematite to magnetite in H2-H2O mixtures by weight-loss method, stressed that the resistance of the porous magnetite layer to the diffusion of gases cannot be neglected in consideration of the overall reaction rate. In the present study the contributions of interfacial chemical reaction, diffusion of gases through the magnetite phase, and the gaseous boundary layer to the overall reaction rate will be considered. APPARATUS AND PROCEDURE Hematite Specimens Preparation. Natural hematite ore from Vermillon range of Northern Minnesota was selected for the present investigation because of its high purity and thermal stability. Chemical analysis of five samples gave the following average values: 67.52 pct total iron (96.62 pct Fe2O3, 0.28 pct FeO, 0.03 pct metallic iron), 2.53 pct SiO2, <0.07 pct MgO, 0.03 pct CaO, 0.05 pct combined mixture, 0.07 pct loss on ignition, and 0.34 pct other. Cylindrical specimens of 0.93 cm in diam and 2.7 cm in length were drilled from slabs of ore with a water-cooled diamond core drill. These specimens were heated to 1000°C and furnace-cooled. Specimens with silica pockets developed large cracks. The uncracked specimens were heated a second time, and their surfaces were carefully examined with a microscope. Those with hairline cracks or surface inhomoaenitv-- were rejected. Preparation of H2-H2O Mixtures. H2-H2O mixtures were prepared by the combustion of H2-O2, mixtures in a pyrex glass chamber in the presence of a catalyst. Alumina pellets coated with palladium, supplied by Englehard Industries, were used as the catalyst. Purified grades of hydrogen and oxygen were used which were repurified by usual techniques. Hydrogen before entering the combustion chamber was passed through an activated alumina H2O absorption bulb, with copper turning at the top. The cover of this bulb was not made pressure-tight so that any pressure development in the hydrogen line would cause the cover to blow off and also the copper turnings would act as a flame arrester in the case of a flashback from the combustion flame. Oxygen flow rates were measured with a bubble flow meter after purification with 1 pct accuracy. Hydrogen flow rates were measured by "precision wet test meter" and the amount of unburnt hydrogen was accurately measured by a bubble flow meter, after condensing water vapor in the gaseous stream. The Pyrex glass bulb contained concentric Vycor glass tubes as shown in Fig. 1. Oxygen was prevented from diffusing into the hydrogen line by threading platinum wire through pores at the combustion end of gas inlet tube. The glass bulb was heated with a Kanthal heating wire pasted in asbestos paper. The surface temperature of the bulb was measured with a thermocouple and adjusted to remain at approximately 350°C. The gaseous reaction chamber also served as a preheater for gases to avoid thermal segregation. The following sequence of operation was adopted. 1) Nitrogen was passed through the outer concentric tube to purge the catalyst bulb of oxygen. 2) Hydrogen was introduced through the inner tube until a steady flow was obtained. 3) Oxygen was then introduced into the nitrogen stream passing through the outer tube. 4) When combustion had commenced and a flame was visible over the platinum wire, the N2 was turned off.

Jan 1, 1969

By Paul M. Tyler

THE winning of metals from Nature has been advanced to a degree of efficiency that commands admiration even in this Machine Age. Economy of human effort underground, in surface plants, and in treatment works, and better means of performing all manner of operations have cut costs and im¬proved products to an extent that seems far beyond the wildest imagin¬ings of those that labored in the days of hand mining and muscular metallurgy. Principles and methods borrowed from other professions and sciences - mechanical engineering, chemistry, and physics-all have con¬tributed to the rapid development of ore production and treatment, but no small part of the achievements must be credited to the free exchange of ideas within the industry itself and mass attack upon problems of mutual concern. The esprit de corps or class consciousness that has contributed so effectively to the progress of the metal industries has been less apparent among nonmetallic mineral producers. As a class they have been handicapped by inadequate contact with the metal-mining fraternity as well as among themselves.

Jan 1, 1935

Discussions of the paper of Mr. Gayley read by title at the Lake Superior hieeting, but first presented at the New York meeting of the Iron and Steel Institute, October, 1904 (see p. 746). With the exception of Mr. Pourcel&apos;s discussion (p. 1038), these papers are here published under a mutual agreement between the Councils of the two Institutes, and will also be found, with others, in the Journal of the Iron and Steel In-slitute for the pear 1904, Mr. E. Windsor Richards, Past-President,&apos; said that in 1799 Mr. Dawson, of Low Moor, read a paper before a scientific society in York pointing out the great diff&apos;erence in the moisture of the air going into the blast-furnace in the hot months of the year and in the winter months. A cold blast-furnace was a very sensitive instrument, and showed this very clearly, for in June, July and August the furnace did not drive so well; it did not make the quality of iron and required more fuel; so that Mr. Gayley was on the right road to effect an enormous improvement in this direction. He considered that Mr. Gayley was on the way to great success, and hoped that the apparatus would not be a very expensive one. He supposed it mas too early for Mr. Gayley to let them know what the saviug was

Jan 1, 1905

By John G. McLain

OF all the zinc that the world consumed in 1936-&apos;38 the United States took about 31 per cent, and almost 14 per cent of the world&apos;s zinc supply in that period was used for galvanizing purposes in the United States. Further examination of the statistics shows that about 71/2 per cent (147,500 tons in 1939) of the world zinc consumption goes into the galvanizing of sheets in the United States, which is what I am going to talk about in this paper. There is nothing especially new about galvanizing; in every year since 1921 somewhere between 41 and 49 per cent of the country&apos;s zinc consumption has been used for this purpose, and yet few people not specialists in its manufacture know much about how it is made. You take an iron or steel sheet and dip it in molten zinc and there you have a galvanized sheet-that about epitomizes popular knowledge of the subject even among engineers.

Jan 1, 1941

By Roscoe W. Stensrud

Marcona Mining Company operations are located 500 kilometers south of Lima, Peru, on the Pacific Coast, at approximately 15º-22&apos; latitude south and 75º-11&apos; longitude west. The terrain is sandy rolling hills ranging from sea level at the coast and rising sharply (escarpment) to an elevation of 800 meters at the mine area. The climate is arid and windy with a moderate year-round temperature, ideal for a year-round mining operation. San Juan, a new and modern community of 14,000 inhabitants and developed by Marcona, houses the working forces and their families.

Jan 11, 1968