Search Documents

By J. A. Berger, R. J. Towner

The pjPocesses of polygonization and subgrain growth were followed in slightly stretched 99.99 pct A1 single crystals heated for cumulative times at 400°, 500°, and 600°C. Changes in sub-grain size and boundary angle were determined from measurements on X-ray micrographs. CAHN1, 2 studied polygonization in stretched and heated aluminum single crystals of 99.99 pct A1 using various techniques, including etch pits, Laue patterns, and a slight restretching of heated specimens to reveal small changes in lattice orientation by the direction of new slip lines. He found that kink bands, which had well-defined boundaries lying in a plane perpendicular to the slip direction (at least in the early stages of deformation), formed during stretching. Also, he noted that bending occurred about the <211> axis lying in the (111) slip plane perpendicular to the <110> slip direction. His studies of polygonization were largely confined to the kink bands rather than to the weakly bent matrix regions between bands. The minimum temperature required to bring about polygonization was established at about 450 "C. Guinier and Tenevin used a focusing Laue X-ray diffraction technique to study polygonization in aluminum single-crystal specimens of 99.99 pct purity. Stretching the crystals 5 pct in tension caused a widening of the focused Laue spots. After heating for 4 hr at 450°C, their method revealed no change in the specimen. Above 450°C polygonization was detected and further annealing near 600°C led to subgrain growth. They concluded that the orientation of the crystal relative to the axis of deformation had no marked effect on polygonization. Gay and Honey-combe4 using an X-ray microbeam technique found that polygonization did not occur in a stretched aluminum crystal heated at 250oC, although some decrease in the yield strength occurred. When the temperature was raised to 475oC, the asterism became broken up as a result of polygonization. Honeycombe5 noted that reflections on X-ray mi-

Jan 1, 1961

By E. C. Olsen

This paper describes the unusual hazardous conditions encountered in mining thick, inclined coal beds under heavy cover in Carbon County, Utah. This description includes heavy roof conditions, sloughing ribs, steep pitches, and severe bouncing experience. Emphasis is placed on the top bench system of mining and development in the top half of a 16-ft seam, under the roof rock, which is bolted, and the recovery of the bottom coal on retreat; success of bolted roof and ribs; and shuttle car haulage on pitches up to 25%. The use of protective cages for operators of face equipment, the guarding of belt conveyor systems to prevent injury associated with deliberate entry, and the positive lockout of electrical equipment is described and illustrated. Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that in- fluence mining. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined conditions are met in the coal mines of the Columbia-Geneva Steel Div. of the United States Steel Corp., in southeastern Utah. This coal bed measures up to 16 ft in thickness, the pitch is as much as 25% and mining is under a cover approaching 3000 ft. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colo. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest. It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development. MINING PRACTICES Mining has generally been confined to the Lower Sunnyside Seam which measures from 7 to 16 ft in

Jan 1, 1963

By L. J. Health

Synthetic rock with predictable porosity and permeability has been Prepared from mixtures of sand, cement and water. Three series of mixes were investigated primarily for the relation between porosity and permeability for certain grain sizes and proportions. Synthetic rock prepared of 65 per cent large grains, 27 per cent small grains and 8 per cent Portland cement, gave measurable results ranging in porosity from 22.5 to 40 per cent and in permeability from 0.1 darcies to 6 darcies. This variation in porosity and permeability was caused by varying the amount of blending water. Drainage-cycle relative permeability characteristics of the synthetic rock were similar to those of natural reservoir rock. INTRODUCTION The fundamental behavior characteristics of fluids flowing through porous media have been described in the literature. Practical application of these flow characteristics to field conditions is too complicated except where assumptions are overly simplified. The use of dimensionally scaled models to simulate oil reservoirs has been described in the literature. 1-3 These and other papers have presented the theoretical and experimental justification for model design. Others have presented elements of model construction and their operation. In most investigations the porous media have consisted of either u ncon soli da ted sand, glass beads, broken glass or plastic-impregnated granular substances—materials in which the flow behavior is not identical to that in natural reservoir rock. The relative permeability curves for unconsoli-dated sands differ from those for consolidated sandstone. The effect of saturation history on relative permeability measurements is discussed by Geffen, et a1.4 Wyga15 has shown quite conclusively that a process of artificial cementation can be used to render un consolidated packs into synthetic sandstones having properties similar to those of natural rock. Many theoretical and experimental studies have been made in attempts to determine the structure and properties of unconsolidated sand, the most notable being by Naar and Wygal.6 Others have theorized and experimented with the fundamental characteristics of reservoir rocks. This study was conducted to determine if some general relationship could be established between the size of sand grains and the porosity and permeability in consolidated binary packs. This paper presents the results obtained by changing some of the factors which affect the porosity and permeability of synthetically prepared sandstone. In addition, drainage relative permeability curves are presented. EXPERIMENTAL PROCEDURE Mixtures of Portland cement with water and aggregate generally are designed to have certain characteristics, but essentially all are planned to be impervious to water or other liquids. Synthetic sandstone simulating oil reservoir rock, however, must be designed to have a given permeability (sometimes several darcies), a porosity which is primarily the effective porosity but quantitatively similar to natural rock, and other characteristics comparable to reservoir rock, such as wettability, pore geometry, tortuosity, etc. Unconsolidated ternary mixtures of spheres gave both a theoretically computed and an experimentally observed minimum porosity of about 25 per cent.7 By using a particle-distribution system, one-size particle packs had reproducible porosities in the reproducible range of 35 to 37 per cent.6 For model reservoir studies of the prototype system, a synthetic rock having a porosity of 25 per cent or less and a permeability of 2 darcies was required. The rock had to be uniform and competent enough to handle. Synthetic sandstone cores were prepared utilizing the technique developed by Wygal.5 Some slight variations in the procedure were incorporated. The sand was sieved through U. S. Standard sieves. A 18-20 sand denotes that the sand passed the Number

Jan 1, 1966

By H. David Swain

On Bougainville Island in Papua New Guinea, Bougainville Copper Ltd. (BCL) has successfully applied electronic data processing (EDP) techniques to pit operations and mine planning. Though the EDP program is not complete, BCL has realized significant improvements in short and long range mine planning, and equipment and manpower utilization. About 80% of BCL&apos;s 4000 employees are Papua New Guinea nationals, and most have little education or training. The operational characteristics of the computer equipment, however, have been quickly adapted by users with low educational standards.

Jan 3, 1979

By H. J. de Haan, L. Schenk

Scope for Thermal Recovery in Shell&apos;s Heavy Oil Fields in Venezuela The main heavy oil reservoirs on the East coast of Lake Maracaibo (Fig. I), known as "Bolivar Coast", initially contained some 20 billion bbl of oil in place with gravities in the range of 10 to 15° API. The current total production rate is about 400,000 B/D. Since the recovery to date is on an average only 12.5 percent of the initial oil in place, these fields offer a vast potential for secondary recovery methods. The reservoirs are characterized by moderate depth (generally 1,000 to 3,000 ft; maximum 5,000 ft), good formation properties such as net oil sand thickness (50 to 300 ft), high porosity (30 to 40 percent) permeability (1 to 3 darcies) and oil saturation (initially about 80 percent) and high oil viscosity (100 to 10,000 cp in situ), all of which are favorable for the application of thermal recovery processes. Since 1957, steam drive, steam "soak" and underground combustion have been tested or are being tested in this area.1-3 This paper deals with a major steam drive test in the Tia Juana field. The test was commenced in Sept., 1961, on the basis of encouraging results of laboratory experiments and pilot field tests, which will be discussed briefly. Early Laboratory Investigation of the Steam Drive Process In 1956 a series of model experiments was carried out in the Koninklijke/Shell Laboratorium, Amster- dam, to investigate the displacement of heavy oil by steam.&apos; The prototype studied was a horizontal, un-consolidated heavy oil reservoir, subjected to a linear steam drive. The model, representing a slab from this reservoir along the main flow direction, consisted of a steel tube filled with oil-saturated sand, provided with layers of rock at the top and bottom to simulate conductive heat losses to cap and base rock. Lateral heat losses, perpendicular to the main flow direction, were minimized by insulating the sides of the model. Heat flow and viscosity and gravity forces were scaled by taking the steam injection rate and sand permeability inversely proportional to the geometric reduction factor of the model, and using materials (oil, steam, cap rock, etc.) identical with those of the prototype. The main feature of the process was a frontal displacement mechanism that was observed within wide ranges of injection pressure and rate, oil viscosity, initial oil saturation and sand permeability. The high stability of this front can be attributed to the high volumetric steam flow rates, combined with the reduction in oil viscosity. High recoveries were obtained due to the low residual oil saturation of about 15 percent in the zone swept by steam. The latter value pertains to the specific test conditions (heavy oil, uncon-solidated sand) and may be lower for light oil, due to the effects of steam distillation. The applicability of this experimental approach is limited, as it does not take into account the fact that

Jan 1, 1970

By R. A. Wattenbarger, H. J. Ramey

The trend in gas well testing has been to rely more on the early-time flow data of drawdown and buildup tests than on stabilized flow tests. The stabilized testing methods often are not adequate for complicated modern gas reservoirs because many of these reservoirs have extremely low permeabilities and the transient flow period of a well test can last for days or weeks. It has become common to augment the flow capacity of gas wells by hydraulically fracturing their producing formations. In deep reservoirs the induced fractures are generally vertical and tend to follow a single plane of weakness. The presence of a vertical fracture at the wellbore complicates the transient flow behavior of a low permeability gas well. The flow is further complicated when turbulence occurs near the wellbore. Russell and Truittl published transient drawdown solutions for vertically-fractured liquid wells. They developed methods of drawdown and buildup testing utilizing these solutions, which were based on numerical simulation. Clark2 applied the basic Russell-Truitt solutions to analyze fractured water injection wells by falloff tests. Field examples were given to substantiate the method of analysis. The Russell-Truitt solutions and well testing methods can be extended to gas well flow. Millheim and Cichowicz3 presented the drawdown equations for *Now with Scientific Software Corp., Denver. ideal gas flow, including the effects of formation damage and turbulence. Two actual field cases were presented, both of which exhibited extensive fractures and turbulent flow. For the pressure range of these well tests, the use of ideal gas equations was acceptable. These field cases were significant in being the first published data showing the occurrence of turbulence in fractured gas wells. We, also, observed such cases in practice. Our purpose here is to extend the theory of fractured gas well testing to the flow of real gases. To determine the effects of wellbore storage and turbulence on well test interpretation, we developed a finite-difference model to simulate well test conditions. Since gas wells usually are widely spaced and have high compressibility, the emphasis has been put on the early transient behavior before the effects of the outer boundary are noticeable at the wellbore. The Mathematical Model The geometry of our mathematical model is similar to that used by Prats.4 The well is centered in a circular uniform reservoir. A vertical fracture of infinite flow capacity penetrates the formation and passes through the wellbore. The wellbore itself is not important. Fig. 1 shows a sketch of the problem. Fig. 2 shows the idealized model. The equation for the flow of real gas in a porous medium with uniform porosity, permeability and thickness is5-7

Jan 1, 1970

By Johannes Moeljono, Werner Wenzel, Heinrich Wilhelm Gudenhau

As an important mechanism for increasing production of the suction-draft-sinter process, it has been shown that gas permeability through the sinter layer plays an important role. Methods to increase production rates have been indicated and suggestions for carrying out the process have been made to improve the rate of production, reduce the fuel consumption, and at the same time obtain a uniform sinter. Laboratory experiments were conducted at the Institute for Ferrous Metallurgy of the Technical University at Aachen to illustrate these methods. Methods of Increasing Gas Penetration Through Sinter Layers The following are of fundamental importance in determining the process cycle during the sintering of iron ores: 1) Generation of maximum temperature, since its form and range determine sinter quality. 2) Propagation velocity of the temperature maximum which controls the attainable output. 3) The convective heat transfer which influences the velocity of travel of the temperature maximum.

Jan 1, 1974

By T. H. Oxnam

INTRODUCTION. THE predominating value of the ores now being treated by the Palmarejo and Mexican Gold Fields, Ltd., is silver, although some gold is also carried. The present method of treatment consists of wet-crushing and concentrating, followed by the cyanidation of the unroasted sands and slimes. The sands are treated by leaching and the so-called accumulated slimes by a system of agitation and decantation. It is only within very recent years that the cyanidation of unroasted silver-ores has been commercially successful. In fact, at the time operations were begun at the cyanide-plant at Chinipas, February, 1902, I knew of no other leaching-plant treating similar ores successfully. The cyanide treatment of the Palmarejo ores differs but little from the ordinary practice in cyaniding gold-ores; and perhaps but little, if any, new information concerning the metallurgy of silver is to be gleaned from it. PALMAREJO MINE. The Palmarejo mines are located in the southwestern part of the State of Chihuahua, Mexico, on the foothills of the Sierra Madre mountains, at an elevation of 3,200 feet. The mills, 12. miles distant, are situated on the Chinipas river, near the town of Chinipas, which is about 150 miles northeast of Agiabampo, on the Gulf of California. Supplies are shipped via this port as this route is the best and most direct to the property. The ore-bodies in the Palmarejo mines have been deposited. along a series of rock-fractures, caused by an intrusion of eruptive rock. The most important of these fractures or fissures, both in width and value, are the Prieta and Blanca veins, which.

Jul 1, 1905

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1939

By C. G. Dunn

James, Jones, and Leak (JJL) conclude that growth-rate and orientation-distribution data obtained in a steep thermal gradient should be used with caution to account for isothermally produced recrystallization textures. I agree. However, it is not clear whether they conclude a) that the orientation dependence of rate of growth of secondaries in (commercial) silicon iron depends on both temperature and a temperature gradient or b) that, in applying rate data obtained in a steep thermal gradient, the isothermal annealing temperature must be close to the temperature for which the rate data apply. Also, it is not clear what tem-

Jan 1, 1967

By Maxwell Gensamer

Jan 1, 1960

By E. C. Stephens

The eastern Washington— Idaho clay region stretches along the northeast margin of the Columbia basin for 150 mil es. The three better known and developed clay areas are Clayton, Wash., (2 miles north of Spokane); Mica, Wash., (10 miles southeast of Spokane); and Moscow-Deary-Bovill, Latah County, Idaho (about 80 to 90 miles southeast of Spokane) see Fig. 1. Clays from the eastern Washington— Idaho clay area have been mined for more than 50 years. At present Mica, Washington deposits are used by the Gladding—McBean & Co. to make a variety of bricks and ceramic products and Latah County, Idaho clays are used by the A. P. Green Fire Brick Co. to make refractories. The Anaconda Co. made an intensive investigation of the clay deposits in the northeastern Washington-!daho area in 1919 to determine the existence of a supply of raw materials from which alumina could be made. The greater part of the work, which included systematic drilling and shaft sinking, was concentrated at Mica, Wash. This was part of a research project carrted on by the Anaconda Metallurgical Research Dept. under the direction of Frederick Laist and F. Frick and it was terminated in 4920. V. D. Perry, Vice President and Chief Geologist for The Anaconda Co., in 1952 assigned the writer to make a preliminary study of clay and other potential sources of alumina ore in the Pacific Northwest with particular emphasis on those deposits which might be of future importance to The Anaconda Co9s. then new aluminurri plant at Columbia Falls, Mont.

Jan 1, 1961

By D. R. Parrish, F. F. Craig

In some respects, forward combustion (alias: fie-flooding, underground combustion, in-situ combustion, dry combustion) is an efficient oil recovery method. For example, its displacement efficiency (as much as 95 percent in reservoirs with high porosity and high oil saturation) is good. In its use of heat, however, forward combustion is grossly inefficient. Most of the heat generated during forward combustion is wasted. About one-fifth of the heat is picked up by the incoming air and re-used (regenerated); the remainder is left behind the combustion zone and ultimately is lost. Compressed air is expensive, and heat generated from compressed air via underground combustion is too valuable to be thrown away. Improvement is needed. Since the early 1950&apos;s, improvements in forward combustion by addition of water injection have been discussed, particularly in the patent literature, with increasing frequency.&apos;-&apos;&apos; These concepts are based on the fact that relatively inexpensive water can be used to pick up much of the heat that is ordinarily wasted during forward combustion, and transport it forward to a more useful place, thereby reducing the amount of air required to move a heat front through the reservoir. Several approaches have been proposed. Merriam and Squires1 taught that a combustible (fuel) gas should be injected along with the air and water. This, however, would give at least a tendency toward reverse combustion instead of forward combustion, and would reduce the velocity of the heat bank, defeating the primary purpose of the water injection. Pelzer2 described primarily a batchwise method of forward combustion and water flooding. He advocated burning part way through a reservoir with forward combustion, then switching from air to water injection alone to push the heat toward the producing wells. Though possible, this method has serious disadvantages, the major one being that, by the time water injection is started, much of the heat has been irretrievably lost to the overlying and underlying formations. We have described what is considered a practical Combination Of Forward Combustion And Water-flooding (COFCAW).3,4 Air and water are injected simultaneously (or alternately) after a small heat bank has been formed by forward combustion. Some of the injected fluid fills up the region behind the heat bank; the rest enters the heat bank. Upon encountering heated rock, the water is converted into steam, which then flows ahead of the combustion zone and displaces much of the oil in place. Only enough air is injected to provide heat for vaporization of the water and to compensate for reservoir heat losses. Since the size of the heat bank is minimized, heat losses also are minimized. Because of more efficient oil displacement ahead of the combustion zone, fuel consumption is reduced. Too, unlike a forward combustion zone that cannot move until all fuel at a point has been consumed, COFCAW leaves some

Jan 1, 1970

By Ivan Simon, R. K. McConnell

Anticipating the availability of tiltmeters suitable for use in boreholes, this article proposes a method of using one or more of these meters to determine in situ stress distribution before and after mining operations. Several ways of using relief techniques to measure in situ stresses in rocks have been developed. These techniques, summarized by Merrill,1 involve measuring deformations which take place when a specimen of rock is wholly or partially isolated from the stress field in the surrounding rock. Measurements of rock deformation caused by stress relief from mining operations can, in principle, also be used to estimate in situ stress distributions. Müller2 has mentioned experiments being carried on in Austria with a "deformation indicator" to determine the tilting of holes drilled before a mine opening is made. Similar work using borehole extensometers has been reported by Potts? and Duvall4 has called attention to the possible use of tiltmeters in making these measurements. Considerable attention is now being paid to the use of tiltmeters in detecting rock deformation associated with fault movements, earthquakes, earth tides, etc. The instruments used for these measurements have usually been of the mercury tube, water tube, or quartz fiber type, but because of their large size, and/or fragile nature, such instruments would not be suitable for use in mining stress measurements. Recent instrumentation developments, however, give promise that rugged, sensitive tiltmeters small enough for use in boreholes may soon be available.&apos; In anticipation of these developments, this article presents a number of calculations of the possibility of using one or more tiltmeters emplaced in a drill hole prior to mining operations to determine the in situ stress distribution both before and after a mining operation. Consider point p (x, z) near a tunnel of radius a

Jan 1, 1969

[Chairman ZAY JEFFRIES, Vice-chairman S. SKOWRONSKI, Chairman WILLIAM M, CORSE, Secretary Executive Committee J. R. FREEMAN, JR., Local Section G. E. JOHNSON R. S. ARCHER, Non-ferrous Data Sheets P. D. MERICA EDGAR C. BAIN, Journal Committee L. W. SPRING SAM TOUR, Papers Committee F. L. WOLF H. C. JENNISON, Membership Committee Local Section Committee J. R. FREEMAN, JR., Chairman R. J. ANDERSON, Cincinnati R L. DOWDELL, Minneapolis R. S. WILLIAMS, Boston G. H. CLAMER, Philadelphia W. A. SCHEUCH, Chicago R. F, Woon, New York Papers Committee S. SKOWRONSKI, Chairman F. H. DIx, JR.-Aluminum E. R. DARBY-Bronze C. S. WITH ERELL-Copper H. A. BEDWORTH-Brass W. K. FRANK-BRONZE F. W. HARRIS-Copper R. L. SUHL-Nickel H. M. ST. JOHN--Foundry Metallurgy R. S. DEAN-Theoretical Metallurgy]

Jan 1, 1928

Jan 1, 1970

By William H. Bassett

RECENTLY it has become the custom of retiring presidents to talk of the relations of the Institute to its membership and its constituency- and it seems a good precedent to follow. Past-president Smith reviewed our relations to materials and to society in general. Mr. Bradley spoke of the value and use of our publications and of our educational duties. My message will be in regard to the coordination of our various groups of member interests and of service to industry. This Institute has, within its organization, four divisions and fourteen technical committees--each interested in a separate put very definite subject, and each covering a phase of mining engineering interest. These vary from geology and the geophysical methods of prospecting, to the physics of the structure of metals, truly "from the mine to the consumer"-from the preparation for mining to the final use of that which has been mined.

Jan 1, 1931

By J. E. Warren, J. H. Hartsock

An asymptotic solution to the equation that describes the flow of a slightly compressible fluid in an infinite porous medium has been used to estimate the interaction between two adjacent wells producing from a common reservoir. A direct method for approximating the interference time defined by Stevens and Thodosl has been suggested. An alternative definition for the time of interference, based on the minimum pressure change in the interference region, has been proposed; also, a direct method of determination has been prescribed. Examples have been employed to illustrate the use of both methods.

By Robert Stefanko

With passage of the Clean Streams Act of the Commonwealth of Pennsylvania and its impact on the coal industry, considerable research has been conducted to explore various approaches to the problem, including deep-well disposal. Available drillhole data from gas and oil wells were used to develop cross -sectional maps for various portions of the state and potential disposal zones were evaluated. Bethlehem Mines Corp., faced with a severe water problem at its Marianna operation in Washington County, cooperated with the Dept. of Mining at The Pennsylvania State University in establishing a 1500-ft well into the Salt Sands for the purpose of determining the feasibility of mine water disposal. The thickness, porosity, and permeability of the formation at the well site proved to be below what had been anticipated from drillhole data. Further, subsequent hydraulic fracturing did not improve the flow characteristics of the well; pumping pressures remained in the range of 1800-2000 psig for disposing of water at the rate of 150 gpm. The legal problems of disposal at the site were very formidable. When the Salt Sands proved to be less than satisfactory, permission could not be obtained to dispose in other promising formations. The paper details many of the problems associated with the experimental well and makes an assessment of the potential for deep-well disposal of mine water. The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given e1sewhere.l,2 The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania. Enactment of more restrictive clean-water legislation in Pennsylvania recently had a great impact on the coal industry. Among its provisions was the reclassifica-tion of most mine water as industrial waste whose dis-posal is prohibited in any stream of the Commonwealth. This had the effect of accelerating research in a variety of areas, although treatment methods still retained primary interest. When a feasibility study of deep-well disposal was proposed to the Pennsylvania Dept. of Mines and Mineral Industries, the Coal Research Board (CRB) approved it. This paper summarizes the efforts on this project. Acid mine water is a chemically complex liquid. having no definite quantitative relationship among its constituents. However, it is the iron disulfide (FeS2) associated with practically all coal seams that produces the objectionable products present in acid mine water when combined with air and water. The principal contaminants are sulfuric acid (H2SO,) and ferric hydroxide (Fe(OH)2. Ferric hydroxide is a rust-colored gelatinous precipitate that coats stream bottoms and destroys aquatic life. However, other ions and bacteria are present in acid mine water in varying amounts.

Jan 1, 1971

Jan 1, 1963