Search Documents

ARIZONA Phoenix Arizona Mining Journal. B Carnegie Public Library. B Tucson University of Arizona, Mining Engineering Society. B CALIFORNIA Berkeley University of California, Mining Asso. B University of California, Library. B & T Los Angeles Chamber of Mines and Oil. B Public Library. B & T Oakland Oakland Free Library. T Sacramento California State Library. B. San Francisco Bureau of Mines Experiment Station. 13 California State Mining Bureau. T Mechanic's Mercantile Library. B Mining and Scientific Press. B Stanford University Stanford University Geological and Mining Society. B San Diego Public Library. B

Jan 1, 1923

By Pol Duwez, Spencer R. Baen

A LTHOUGH the practical importance of Fe-Cr--iV Mo alloys has long been recognized, constitution studies have been limited to a few alloys within rather narrow ranges of composition. The purpose of the present study was to establish the phase boundaries in the ternary diagram at a temperature of 1200°F (650°C).* The identification of phases and the determination of phase boundaries were based primarily on X-ray diffraction measurements and occasionally on microscopic observation. The methods used for locating the phase boundaries were essentially those described in detail by Andersen and Jette,' and by others.', The compositions of 180 alloys, prepared by powder metallurgy techniques, are shown in Fig. 1. The chemical analysis and mesh size of the powders which were used for the preparation of the alloys are given in Table I. The powders were mixed for 48 hr or longer, then compacted under 80,000 psi in a %-in. diam steel die. Each specimen weighed approximately 5 g. The compacts were sintered for 4 hr at 2500°F (1371°C) in an atmosphere of pure dry hydrogen (dew point near the temperature of liquid nitrogen). An open tray of chromium powder was placed upstream of the compacts to act as a "getter" for the last traces of oxygen or water vapor. In many cases this chromium powder was bright after sintering. Occasionally the upstream side of the powder was slightly greenish, but in all cases the downstream side was metallic. Some of the alloys contracted during sintering and some expanded as much as 20 pct. The latter alloys, which in all cases were brittle, were crushed in a tool steel mortar, repressed, and resintered for 4 hr at 2500°F. After sintering, the alloys were aged for ten days at 1200°F (650°C) in evacuated (105 mm Hg or better) fused silica tubes and were cooled rapidly to room temperature following the aging treatment. The use of the powder metallurgy technique in preparing alloys for structural investigation offers a simple method 'of avoiding contamination or non-homogeniety which could result from a melting operation. It is very often possible to dispense with chemical analysis of the alloys which have been prepared by the powder metallurgy method. In lieu of chemical analysis, it is necessary to determine the weight of the compact before and after sintering. The chemical composition of the alloy may be considered as that of the green compact, within the limits of accuracy determined by the loss of weight during sintering. In phase-diagram studies it is important to achieve homogeniety in structure, whether the alloys are prepared by powder metallurgy or by melting. Homogeniety means complete diffusion during the sintering of the alloys which are prepared by powder metallurgy. It has been found from experience that the best criterion for establishing the completeness of diffusion is the sharpness of the X-ray diffraction patterns. This criterion has been used throughout the present study. The X-ray diffraction data were obtained using powder cameras of either 214.86 or 71.62 mm diam. Copper, cobalt, or chromium Ka. radiation was used, the choice being based on the alloy composition. The powder samples were obtained by filing or crushing, depending on whether the alloy was ductile or brittle. In some cases, the powder was annealed for 4 to 6 hr at 1200°F in vacuum. The measurements were corrected for film shrinkage and absorption. The large camera, in which the film is mounted

Jan 1, 1952

By Leonard Grimshaw

THE idea of bonding two dissimilar ferrous metals, and making use of both, is an old one. Tips have been brazed onto tool shanks for many years. The bonding of larger pieces to form whole bars and sheets has also been accomplished, but has received little attention in the technical literature, although a number of patents have been issued covering various methods for its accomplishment. There are three main motives behind the manufacture of composite steels. One is that the physical properties of one steel may supplement those of another; a useful, but at the same time, hard, brittle steel may be backed by a soft ductile one, or a stainless steel may be backed by a steel possessing greater strength. Another motive is direct lowering of cost; an expensive steel may be backed by a less expensive one, bringing down the cost of the piece as a whole. The third motive is an indirect lowering of cost, as when a useful steel is backed by a steel that is easier to machine, so that machining cost on a finished product is lowered considerably. Often more than one of these motives lead to a decision to use a com-posite steel.

Jan 1, 1936

By J. F. Tavernelli, L. F. Coffin

The deformation and fracture characteristics of eight metals subjected to fully reversed cyclic strain ranging from 0.2 to 50 pct were investigated at room temperature. Strain-hardening characteristics unique to the interna1 structure of a particular metal were found. Complete removal of the strain-hardening effects resulting from prior deformation was brought about by subsequent cyclic strain. Further support for the validity of the inverse relationship between the plastic strain range and the square root of the number of cycles for failure is given. THE resistance of materials to cyclic plastic strain is of interest both from a fundamental and practical point of view. It is now a well-accepted fact that fatigue failure in metals is a consequence of the localized slip deformation which occurs within the individual crystals of metal.'-' Hence the failure process should be strongly dependent upon the magnitude of the gross cyclic plastic deformation of the metal under conditions where this is a measurable quantity. Therefore, an experimental investigation of metals in which the cyclic plastic strain is the independent variable should shed new light on some of the basic aspects of the problem. From the practical point of view, there are many uses for information relating to the cyclic strain resistance of metals. One is the case of thermal stress fatigue where fatigue failure can occur as a consequence of a com- paratively few cycles of thermally induced mechanical deformation. Another is the mechanical working of metals where large cyclic strains are employed. In recent years several publications have appeared relating to the cyclic-strain resistance of metals,8-11 dealing mostly with the fracture aspects where the temperature is cycled simultaneously with the mechanical strain. Some work has been reported on the cyclic-strain resistance of metals at constant temperature, again oriented more toward the fracture aspects of the problem than the deformation aspects. 12-16 The present research investigation was undertaken to obtain information regarding the deformation characteristics of several metals whose structure-property relationships were simple and straightforward under conditions of both cyclic and monotonic strain. It has been shown for example that under cyclic-strain conditions some materials will strain harden, while other materials, particularly cold-worked structures, strain soften and these effects required further clarification.8,17-19 It was also de-

Jan 1, 1960

By ALFRED D. FLIWN

ENGINEERING COUNCIL is not "about to die," as some persons are saying. Through a natural and foreseen reorganization, Council is entering a new stage of existence with enlarged power for usefulness. Its early constituents have made it possible for many more of their fellow engineers and men of other technical vocations -to take a- share in its activities, responsibilities and support. A new organization is being set up, but it is really a new embodiment of the same spirit of service. Another step is being taken toward the full acceptance by the technical professions of their obligation to the public and to one another for those services which can -be rendered only through effective organization. A brief retrospect is timely. Engineering Council was established in the spring of 1917, as a department of United Engineering Society in response to requests of its Founder Societies. .It followed various attempts of these societies to deal through joint committees with public questions affect¬ing engineers -and with inter-society affairs. These attempts had very limited results. In the new by-laws adopted by United Engineering Society, the purposes and-powers d-powers of Engineering Council were thus defined: "To provide for convenient cooperation between the four Founder Societies, for the proper consideration of questions- of general interest to engineers and to the public, and to provide the means for united , action upon questions of common-concern to engineers.

Jan 1, 1920

By J. Chipman, N. J. Grant, J. C. Fulton

This paper contains data on the distribution of silicon between liquid iron-silicon-carbon alloys saturated with respect to graphite and CaO-SiO2-Al2O3 slags under 1 atm of CO at 1600°C. The ranges of slag compositions studied were extended from the dicalcium silicate saturated liquidus composition up to silica concentrations at which Sic appeared as a stable phase. IN blast furnace operation it is not to be expected that slag and metal reach equilibrium with one another. Nevertheless, the silicon content of the metal varies with slag composition and with temperature in a manner which would be predicted from equilibrium considerations. Similarly, the distribution of sulphur between slag and metal does not attain an equilibrium state, yet the influence of slag composition is strongly analogous to its effect on the distribution equilibrium. The desulphurizing power of metallurgical slags has been shown to be highly dependent upon the FeO content of the slag. Moreover, the rate of removal of sulphur from slags is influenced by the oxygen potential of the slag-metal system. Thus it was shown by Grant, Kalling, and Chipman1 that the presence of MnO in slags which are low in FeO causes a marked slowing down of the transfer of sulphur from metal to slag. This led to the hypothesis that the slow removal of sulphur by blast furnace slags of more acid composition might be due in part to the effect of SiO2 on the oxygen potential of the system. This was verified in the work of Grant, Troili, and Chipman,' who found that the desulphurizing power of the more acid blast furnace slags could be markedly improved by an increase in the silicon content of the underlying metal. Their explanation of this improvement was that the higher silicon content of the metal decreased the rate of transfer of more silicon and, along with it, of oxygen from the slag to the metal. The slowness of the transfer of sulphur from metal to slag was the result of the slow reduction of SiO2 from slag to metal. Attempts to study the rate of sulphur removal had in the past resulted in very slow rates corresponding to the rates of silica reduction. It has become evident on the basis of these studies that further experimental studies on the rate of removal of sulphur must take these factors into consideration if there is to be a clear understanding of the rate of sulphur transfer under conditions simulating those existing in the blast furnace. It will be necessary, at least in a part of such study, to employ combinations of slag and metal in which the disturbing effect of silica reduction has been eliminated; in other words, to employ slag-metal combinations which are already in equilibrium with respect to the transfer of silicon. In preparation for such studies of desulphuriza-tion, a preliminary program of research on the distribution of silicon between slag and metal has been undertaken. This will ultimately include a comprehensive survey of the effects of temperature and slag composition on the equilibrium distribution of silicon between slag and metal. The present paper is a report on experimental methods employed and on

Jan 1, 1954

By Charles Maier

IT has long been supposed that when crystalline materials are com-minuted the energy used in the production of increasingly smaller grain sizes is not entirely dissipated as heat but that a certain portion is "stored" as a part of the internal energy of the material. This portion usually has been called the "surface energy" of the particles. The practical interest of the Bureau of Mines in this subject in connection with the energy requirements of crushing processes has led to the author's attempt to measure the "stored" energy in finely divided calcite by heat-of-solution methods1. The experiments on calcite showed that "storage" of energy could not be proved for this material, because fine grinding caused a lack of chem-ical homogeneity evidenced by loss of carbon dioxide and subsequent adsorption of water on the surfaces of the calcite particles. When thermochemical correction was made for composition changes the cor-rected heat of solution was less for fine material than for coarse. Con-tinuation of the experimental work into the problem of comparing work and heat in the deformation of metallic crystals, where the calorimetric difficulties were less, showed, however, that in the case of copper and aluminum a real discrepancy between work and heat could be shown. similar results had previously been obtained by Farren and Taylor2 and Hort3 and more or less simultaneously with the author's work by

Jan 1, 1936

Discussion of the paper of George K. Burgess, J. J. Crowe, H. S. Rawdon, and R. G. Waltenberg, Finishing Temperatures and Properties of Rails. By Albert Sauveur, R. Trimble, William R. Webster, P. H. Dudley, George B. Waterhouse, M. H. Wickhorst, James Aston, E. F. Kenney, A. W. Gibbs, W. A. Aiken, and G. K. Burgess . . 767 Discussion of the paper of Albert Sauveur, Manganese Steel and the Allotropic Theory. By G. K. Burgess and J. E. Stead 787 Discussion of the paper of J. V. Emmons, The Surface Decarbonization of Tool Steel. By Albert Sauveur, Bradley Stoughton, E. G. Spilsbury, Oliver W. Storey, H. O. Hofman, and J. V..Emmons 790 Discussion of the paper of Richard H. Rice, Turbo Blowers for Blast-Furnace Blowing. By S. G. Valentine, W. McA. Johnson, L. Iversen, J. E. Johnson, Jr., Karl Nibecker, W. Trinks, Otto Banner, H. S. Braman, Arthur G. McKee, and Richard H. Rice . . . 794 Discussion of the paper of J. K. Furst, The Plant of the Duplex Process for Making Steel. By W. McA. Johnson, Arthur G. McKee, Henry D. Hubard, and Bradley Stoughton . . 810 Discussion of the paper of E. C. Harder, The Iron Industry in Brazil. By I. C. White and E. C. Harder 813

Jan 4, 1915

By Charles Austin

IT has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent C0 and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their pro-portional limits and yield points are rela-tively low. Published data1 for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the results shown in the lower section of Fig. I. TABLE I.-Analysis of Material I Percentages Constituent Sample Sample Sample 3125 3124 3123 Si 0.25 0.51 o.6o Fe 4.15 10.70 13.17 Ti I.15 3.58 4.70 Mn 0.30 0.41 0.42 Co (by difference)^ 94.15 84.80 81.71 The cobalt from all three samples, united and tested for nickel, gave 0.54 per cent Ni based on the weight of cobalt. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deforma- tion characteristics in moderately long-time tests at 600°, 700° and 800°C. after quenching from various solution tempera-tures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain in- FIG. 1.-EFFECT OF VARYING AMOUNTS OF FERROTITANIUM (FE2TI) ON PHYSICAL PROPER-TIES OF COMMERCIAL COBALT. (C. R. Austin.1) Upper section. Tested at 600°C. after water-quenching from 950°C. Lower section. Tested at 600°C. after water-quenching from 950°C. and aging 72 hr. at 650°C. FIG. 2.-PORTION OF QUASI-BINARY DIAGRAM COBALT-FE2TI AS DETERMINED METALLOGRAPH-ICALLY. formation on the quasi-binary system Cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufac-turing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table I. The alloys, when originally made up,1 were based upon an iron-titanium com-pound, Fe3Ti, as indicated by the work of

Jan 1, 1940

AMONG the features that make Inspiration of outstanding A interest, particularly to the engineer, is the fact that at various times it has used, as a major method of production, three more or less distinct methods of mining and three distinct methods of treating its ores. The following chronology is of interest : Major Mining Methods: 1915-194 7 Underground block-caving, exclusively 1948-1952 Underground block-caving and opencut mining 1953-1954 Underground block-caving, opencut mining, and "glory-hole caved-block transfer" mining 1955 on Opencut mining and "glory-hole caved-block transfer" mining. Major Ore Treatment Methods: 1915-1925 Flotation concentration exclusively 1926-1930 Flotation concentration and ferric sulphate leaching 1931-1955 Ferric sulphate leaching (the so-called "Dual Process" was used for eleven months in 1937 when demand for copper was phenomenal; and the "leach-float" process was used for 24 months in 1942-44 as an expedient to help meet war demands for copper). 1956 on "Dual Process" combining a sulphuric acid leach followed by fine grinding and flotation of the residue from the leaching vats.

Jan 1, 1957

By M. Deighton, R. N. Parkins

The metals Cd, ,Wg-, Sn, TI, Zn, and Zr reach a peak hardness after a criticfir1 deformation by rolling- and then soften with fwther rolling-, thereby exhibiting wovk softening. Optical metallography on Cd, Mg, and Zn shows that work softening is accompanied by a change in grain size occurring during deformation. The creep of zinc from -1l° to +60°C at stresses in the range of 7.9 to 17.3 kg per sq mm is given by € = e0 -t- Bt + Kt +at6. The third and second rate constcints are related by the equation a = K~ K6 and their stress and temperature dependence can be represented by the equations K = A, . exp - (u, - Bu)/kT. A model based upon the stress activated glide of sub-boundaries is proposed which qualitatively accounts for the metallog-raphic observations. Expressions, which are in reasonable quantitative agreement with the ex-pe~inzental observations, are derived for the creep of zinc. THE term "work softening" has been used previously by Polakowski1 and by Cottrell and stokes2 to describe phenomena where further strain of a deformed material leads to a decrease in flow stress. In both cases, however, the conditions were changed for the second straining. Here, the term "work softening" is intended to refer to a decrease in flow stress after continued straining in the same direction at the same temperature: work softening is the antithesis of "work hardening". Work softening of zinc was reported by chadwick3 and in discussion of that paper Jenkins4 indicated that cadmium also work softens. More recently work softening has been reported5 in two magnesium alloys, -99.5 pct Mg. Chadwick found that the hardness, 0.2 pct Proof Stress and the UTS of electrolytic zinc all increased with progressive cold reductions up to 30 pct and then progressively decreased with further rolling. Gay and Kelly6 used a back-reflection X-ray technique to study the effect of cold rolling zinc and found that although deformations greater than 2 to 5 pct reduction in thickness produced some recrystallized grains, deformations greater than 40 pct caused com-plete spontaneous recrystallization. At deformations greater than 60 pct the material was found to consist solely of recrystallized grains, -20 pm diam, the size of which decreased with increasing reduction and was much less than the initial grain size of the annealed material (-300 pm diam). Similar results were also reported for cadmium, tin, and lead.6 Gay, Hirsch, and Kelly' suggest that these experiments indicate recrys-tallization takes place when the dislocation density exceeds a certain value. However, no measurements of MATERIALS AND EXPERIMENTAL PROCEDURE The purity of the metals used in this work is indicated by the following figures: Zn (99.99); Cd (99.94); Mg (99.95); T1 (99.99). The zirconium was iodide crys tal bar with a probable purity of about 98 pct. The metals were obtained in the form of 0.25 in. thick strip or 0.425 in. diam rod by various fabrication methods and then annealed to ensure complete re-crystallization. Hardness-deformation curves were obtained at room temperature by rolling 4 in. thick strip under conditions which left a surface adequate for diamond pyramid hardness tests immediately after rolling. The hardness was taken as the niean of five impressions made using a 5 kg load and the time elapsing between rolling and making the last impression never exceeded 5 min. The zinc specimens for creep testing were from 3 by 3 by 4 in. cast slabs which were rolled to 0.10 in. thickness starting at 350°C and finishing cold. The resulting strip was cut into pieces 1 in. wide and annealed in batches. With suitable choices of annealing temperature between 100" arid 400°C five different grain sizes varying from 4.54 x 10' to 3.03 x l05 grains per sq cm (530 to 20 um diam) were obtained. Creep tests were done in compression using a sub-press, based on a design after Ford,8 in which the strip is compressed between dies 0.100 in. wide under conditions of plane strain. Since there is no lateral spread of the material, the area of contact between the dies and strip remains constant throughout the test and the application of a constant load, using the load maintaining device of a hydraulic testing machine, resulted in a constant stress. Covering the dies with strips of P.T.F.E. reduced frictional effects to a minimum. The creep strain was obtained by measuring the travel of the crosshead of the testing machine to a sensitivity of 0.1 pct reduction in thickness. The complete subpress assembly was contained in a steel box and for tests above the ambient this was filled with liquid paraffin and heated electrically. Temperatures below the ambient were obtained with a cooling mixture of acetone and solid carbon dioxide in the box. The liquids were stirred and the temperature of the specimen, which was controlled to ±0.5"C dur-ing a test, was measured by a thermocouple placed near the dies. Compression testing of cylindrical specimens was also carried out in the subpress using hardened flat discs separated from the test material by P.T.F.E. sheets which obviated barrelling of the specimens. Various initial strain rates were supplied by the hydraulic testing machine, and the deformation was measured by a clock dial gage resting on the cross-

Jan 1, 1970

By H. Carroll Weed

By caving a block into the workings of its open pit and using the block as an ore transfer, the lnspiration Consolidated Copper Co. has solved a transportation and sizing problem, making possible a great expansion of open-pit methods as applied to Inspiration ore-bodies. FROM 1915 to 1948 the entire production of Inspiration Consolidated Copper Co. was supplied from underground mining. The sole method used was block caving. Underground haulage and hoisting facilities were designed and geared to large-scale production. Beginning in 1948 open-pit mining was substituted for block caving in a portion of Inspiration's Live Oak orebody. The idea proved so attractive that before the Live Oak pit had come into production, another pit on the Colorado orebody (now the Thornton pit) had been laid out and stripping started. It should be noted that these orebodies were not new and the entire program was one of changed methods of mining. Since part of these orebodies had already been mined by block caving methods, it must be recognized that haulage levels had been established under the area or adjacent to it. The orebodies lay on the south side of Inspiration Ridge, while the shafts, crushers, and treatment plants are all on the north side of this ridge. The existing main crushing plant was designed to take a maximum of 12-in. material, and all ore was sized to this dimension by passing through grizzlies in the stopes. In the original planning for open-pit work much thought was given to the transfer of ore to existing underground levels for haulage and hoisting from the regular shafts. If this could be done the necessity of crossing the ridge could be eliminated. Final decision called for cutting a road through the ridge, installation of a primary crusher at an elevation of 3968 ft on the north side of the ridge, and railroad haulage with existing facilities to the main coarse crusher. This decision was brought about by the difficulties of properly sizing and transferring to underground haulage large tonnages of coarse breaking oxide which lay on the upper benches of the proposed pit. Trucking over the ridge on a 7 pct grade would give a cheaper and more flexible operation in handling this material. The benches in the pits are laid out at 50-ft inter-vals and designated according to elevation above sea level. The lowest bench in the original pit was laid out at 3500-ft elvation. All haulage roads are on a 7 pct grade and a vertical lift of 468 ft was considered about the maximum economically possible from a cost standpoint. After 2 years' operation the advantages of pit mining, both from the standpoint of costs and flexibility of operation, became more and more apparent. Studies were then started to develop the extension of open-pit mining to more of the ore reserve than had been planned originally. The idea of transfer raises was again explored. Obviously, as elevation of the pit was lowered, shorter transfer raises would be needed to reach the main haulage levels. Transportation from the lower elevations to the rim of the pit by belt conveyor or skip hoisting was also considered. However, it was recognized that sizing would be required both for conveying and regulation of feed size to the main crusher plant. This would necessitate a fixed or portable crusher located somewhere in the pit. It was known that the sulphide ore at the lower elevations was softer and easier to break than the overlying oxide of the upper benches. This sulphide ore is very suitable for grizzly sizing. Calculations indicated that for ore mined on 3650 elevation, costs for trucking to the primary crusher, crushing, and delivery by railroad to the coarse crusher would equal costs for dropping the same material to the 600 level, hauling underground, and hoisting directly to the coarse crusher bins, provided a suitable method of sizing and transferring could be developed. Above 3650 elevation costs would favor surface haulage; below they would favor underground haulage. The idea of caving an underground block from the 600 haulage level directly into the bottom of the pit

Jan 1, 1954

CARL A. WENDELL, New York, N. Y. (written discussion*) .-I have never seen in print anything that even remotely has approached this article in clearness and important conclusions in conjunction with work done on the sink-and-float test. I have had many hundreds of these tests made and on different specific gravity solutions and the resultant product analyzed, but I have never grasped nor been able to show what this article sets forth. This article brings out one factor very clearly to my mind; what is to take the place of the solutions of different specific gravities used to obtain the laboratory results, when it comes to washing on a large scale, since water has one constant weight only? The answer is, sizing of coal. And as we know the importance of size versus specific gravity of the material to be washed, perhaps defined (practical) lines can ultimately be gotten up so that the sizing, if any, may be determined at the same time as the laboratory work on the coal is being done. G. R. DELAMATER, ? Steelton, Pa. (written discussion?).-The authors' deductions are well founded and although they disclaim any wide experience in commercial coal washing, practically all of the data presented are applicable to coals of all parts of this country. The paper clearly sets forth the great necessity of careful preliminary investiga-tion of each contemplated washery undertaking and contains the follow-ing very true statements. "It is not safe to assume that any coal which can he successfully washed on coarse coal jigs can be cleaned more com-pletely by washing at a finer size on tables," and "The effect of finer crushing upon the completeness with which impurities may be separated from coal depends upon two opposing tendencies. First, that the more finely a raw coal is crushed, the more completely will the particles of impurities be detached from the particles of clean coal. Second, the finer a coal is crushed the more difficult it becomes to separate the pieces of clean refuse from the pieces of clean coal."

Jan 12, 1919

By J. F. Smith, J. E. Davison

The heat capacity of CaMg2 was measured over the temperature interval, 4.8° to 287°K, by the technique of low-temperature adiabatic calorimetry. Heat content measurements were performed with a drop calorimeter over the temperature interval, 273" to 673°K. From these data the thermodynamic functions, (FT - H0)/T, ST - So, and & - Ho, were evaluated. A third-Law calculation of the standard entropy of formation of CaMg2 yields a value of -0.25 * 0.06 cal per (°K g-atom) , and the free-energy function derived from this study when combined with existing equilibria data yields a value for the standard enthalpy of formation which is in agreement with direct calorimetric enthalpy measurements. The accompanying paper' shows that the enthalpy of formation of CaMg2 has been determined with good precision by three different calorimetric techniques.'-= TWO independent determinations of the Gibbs free energy of formation of CaMg2 have also been made; both determinations were based on vapor pressure measurements, being in one case hydrogen vapor pressures over ternary Ca-Mg-H alloys4 and in the other case magnesium vapor pressures over binary Ca-Mg alloys.5 The present determination of heat capacity of CaMg2 below room temperature and of the heat content of CaMg2 above room temperature was undertaken to provide supplementary data. These data are useful in their own right but can in addition be used to evaluate an entropy of formation for CaMg2 which, because of the interrelation of free energy, enthalpy, and entropy, can be used as a check of the self-consistency of the composite of the presently available information. LOW-TEMPERATURE HEAT CAPACITY The heat capacity of CaMg2 was measured over the temperature interval 4.87° to 286.64°K in an adiabatic calorimeter. The physical details of the calorimeter and the experimental procedure for measuring the heat capacity of a specimen have been adequately described by Gerstein et a1.6 The source and purity of the calcium and magnesium are described together with the methods of sample preparation and chemical analyses in the accompanying paper.' Results of chemical analyses of the material which was used in the present investigation are shown in Table I. These analyses show that, on the basis of the published phase diagram,7 the heat capacity sample contained a slight excess of a calcium while the heat content sample contained a slight excess of magnesium. However, in both cases the excess was small, and X-ray diffraction patterns showed reflections which were without exception attributable to CaMg2. The sample which was used for heat capacity measurements weighed 69 g while the sample container and addenda weighed 132 g. The sample was in the form of annealed powder, 50 to 60 mesh, and was sealed into the sample container under 0.1 atm of helium. Copper fins inside the sample container facilitated thermal equilibrium of the powdered Sample. Time intervals of the order of 10 min were required for thermal equilibration, and such times are normal for this calorimeter regardless of the form of the sample. The observed heat capacities were corrected for the small excess of a calcium through use of the heat capacity values tabulated by Hultgren et a1.8 The corrected heat capacities are tabulated as a function of temperature in Table II. The free-energy function and the absolute entropy of CaMg2, which were calculated from the experimental heat capacity data, are listed in Table 111. A smooth curve was fitted to a plot of the experimental values of the heat capacity and in only two instances above 30°K did the plotted points deviate from the curve by more than 0.2 pct. Below 10°K the deviation of several of the points was as much as 50 pct. These large percentage deviations were attributed to the small value of the heat capacity and to the low sensitivity of the platinum resistance thermometer in this temperature range. The deviations in the region of 10°to 30°K were less than 5 pct. Although the percentage deviations of some of the low-temperature measurements are large, the actual value of these deviations is small since the magnitude of the heat capacity in that temperature range is small. The error in the value of the third-law entropy at 298.15°K was estimated to be less than 0.01 cal per (°K g-atom). A value of -0.25 ±0.06 cal per (°K g-atom) was obtained for the standard entropy of formation at 298.15°K from the relation:

Jan 1, 1969

By Gerald Edmunds

CASTINGS of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, some-times nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is devel-oped to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and there-fore the position of the grains is more com-plex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicat-ing that thermal contact was better there than in neighboring areas.

Jan 1, 1940

By Charles Macdonald

WROUGHT-IRON eye-bars for bridges and roofs, designed upon what is known as the pin connection system, have been successfully manufactured in this country for some years. The most approved methods employed have been the hydraulic upsetting process, and by die-forging under a hammer. In upset eyes the fibre of the iron is necessarily much distorted ; and in bars of considerable size, this disturbance seriously impairs the strength of the connection. Mr. Collingwood, in discussing my paper on "Proportions of the Heads of Eye-bars," read before the American Society of Civil Engineers, Jan. 21st, 1874, submitted sketches of certain bars intended for the anchorage of the East River bridge, which had been exposed to the action of sulphuric acid a sufficient length of time to thoroughly cleanse the surfaces, and expose the condition of the fibre. These sketches are here reproduced for the purpose of illustrating the effect of this methpd of manufacture. In Figs. 1, 2, and 3, it will be observed that the fibres at A, and E, have been folded back upon themselves and otherwise twisted and disturbed, in a manner not calculated to inspire confidence in the integrity of the connection. To compensate for this defect, a large excess of metal is thrown into the eye; but a method of manufacture which involves such a necessity, even although it be the one giving the best results thus far, all things being considered, is far from being perfect.

Jan 1, 1879

Last October a committee was appointed by The War Service Association of Manufacturers of Solder and Bearing Metals, Inc. to consider the report of the U. S. Bureau of Standards to the Conservation Division of the War Industries Board, a letter of the War Industries Board, and the discussions of this letter as reported at the meetings of association and to summarize the information thus obtained. The report of this committee has just been printed. The committee agrees with the Bureau of Standards that 99 per cent. tin can be used. It also finds that a very small amount of lead might increase the tendency of the bearing to crack and that lead has a hardening effect on babbitts up to a possible limit of 10 per cent. of lead. Still in the so-called genuine babbitts, in the presence of lead a certain proportion of low melting point eutectic is introduced which admits of the bearing being poured into thinner sections and is decidedly advantageous in the die-casting process in producing a much smoother casting. But the committee recommends that the Bureau of Standards thoroughly investigate this point. Lead-base babbitts, to give satisfactory service, must be carefully made of the proper raw materials. The bronze hearing that has been thoroughly tinned and containing the thinnest possible babbitt lining is now becoming recognized as the ideal bearing. The compositions, recommended by the committee are as follows:

Jan 2, 1919

By J. E. Burke, C. W. Mason

IN attempting to study precipitation from a tetragonal lattice using solid solutions of bismuth in tin, it was found that although a Widnmanstatten pattern is observed 1 only a qualitative analysis of the orientation relationships is possible, because of the unusual structural changes that accompany the precipitation process MICROSCOPICAL STUDIES Alloys were made from Chempur tin (Standard samples 42b and 42c, National Bureau of Standards), and bismuth (Kahlbaum C P ) by melting neighed quantities together under palm oil, stirring well, and casting in a heated graphite mold The polishing and etching techniques employed largely govern the visibility of the structural changes The preliminary surfacing operations were similar to those recommended by Villela and Bergekoff,5 through BehrManning 3/o abrasive papers, lubricated by a solution of paraffin in kerosene A rough metallographic polish was next given, using a thin cotton cloth charged with relevigated alumina (maximum particle size of about 4µ) and soap solution, repeated etching and polishing served to remove disturbed metal For high-power examination better preparation was necessary It was found that on such soft metals the threads of the fabric, rather than the abrasive, cause most of the scratching Cotton outing flannel, which had been brushed so that the nap lay down, was fairly satisfactory, but a Heavy grade of silk velvet (not the noncrushable kind) was found to be better, especially after some use A better procedure was as follows The metal lap was warmed slightly, and a 4-in circle of woolen broadcloth was cemented to its center by a thin film of melted paraffin The broadcloth was then moistened with water, and a 30 to 40 per cent solution of sodium hydroxide heated to about 50°C was poured over it, allowed to stand for 1 to 2 min and then washed off It was neither necessary nor desirable to remove all the sodium hydroxide from the cloth, since its etching action aided in the removal of the flowed layer from the sample The cloth was then charged with a paste of the relevigated alumina in water Since this lap did not remove deep scratches, it was necessary previously to polish the specimen on some material such as the silk velvet The sodium hydroxide softens and partly gelatinizes the woolen lap covering, permitting a scratch-free polish, but its action continues, and the cloth deteriorates after about 24 hr This is not serious, because a new lap can be prepared in about 5 min, and only small pieces of cloth are used Etching with a strongly acid solution of ferric chloride was found satisfactory for removing the flowed layer For the final etching, the most satisfactory reagent was that of Taffs,7 the formula for which is FeC13 6H20, 2 grams, HC1, 5 c c , H2O, 30 c c , C2H5OH (95 per cent), 60 c c This etchant reveals differences in com-

Jan 1, 1941

By E. G. Williams

Conveyors were first used underground at Miami Copper Co., in the latter part of 1947. At that time some of the stoping area was too heavy and too close to the haulage level to use conventional haulage. To get the haulage drifts out from under the stoping area belt conveyors were used for the additional lateral transfer. Since 1947 more than 8 million tons have been mined in this manner, with as many as four belt type stopes in production at one time. When the mining plan for the new low grade was worked out, it was decided to use belts on what otherwise would have been short train haulage transfers to move the ore laterally to centrally located concrete ore passes. One group of these stopes has grizzly levels on the 570, with a belt level on the 670; the other group has grizzly levels on the 720 and belt levels on the 820, with the concrete ore passes bottoming on the 1000, or the existing train haulage level.

Jul 1, 1956

D. M. Riordan has been appointed a member of the Institute Com¬mittee of the Engineers' Reserve Corps movement. Our Committee, therefore, now consists of Henry S. Drinker, Chairman, Messrs. Arthur S. Dwight, Warren A. Wilbur and D. M. Riordan.

Jan 1, 1916