Search Documents

By T. Toda, R. Maddin

A study has been made of the microstructure and mechanical properties of splat-cooled aluminum-base gold alloys with gold concentration from 0.25 to 5.0 wt pct. These alloys have been quenched from the liquid state by a torsion-catapult technique, which has made it possible to pepare specimens suitable for mechanical property measwements. From the electron micrographs it has been shown that the solid solubility of gold in aluminum can be extended to 2.5 wt pct (0.35 at. pct) by splat-cooling, while the maximum equilibrium solubility is known to be less than 0.3 wt pct (0.04 at. pct). The very fine grain size (several tenths of a micron), the extended solid solubility, and the fine dispersion of a second phase (AuAl2) contribute concurrently to a substantial strengthening effect. In Al-5 wt pct Au splat-cooled specimens of less than 50 thickness, the yield strength is 17 kg per sq mm or 6 times as large as the strength of bulk specimens. For the Al-1.0 to 2.5 wt pct Au solid solution obtained by splat-cooling, the yield strength reaches 7.5 kg per sq mm after an aging treatment (for 10 hr at 200°C), while it is 3.7 kg per sq mm for the corresponding bulk specimens. A great deal of research has been done in recent years on the structure and the properties of metals and alloys rapidly quenched from the liquid state.' The term "splat-cool" has been used with the meaning of a rapid quenching from the liquid state., The splat-cooling techniques have produced large numbers of new structures, which are expressed in terms of metastable phases,3 concentrated solid solutions,4 amorphous phases,5'6 new phases,7 and so forth. Nearly all previous studies have concentrated on the physical properties; i.e., crystallography, structure, electrical resistivity, magnetism, and so forth, of the splat-cooled metals and alloys. The mechanical strength of splat-cooled metals and alloys has hardly been investigated except for some recent work by MOSS' on A1-V alloys. The principle common to all experimental techniques developed to obtain very rapid quenching rates is based on the heat transfer by conduction. Liquid must be in good thermal contact with a substrate of high heat conductivity. Both of the published devices known as the "gun" and the "piston and anvil" techniques suffer from certain shortcomings. For example, the specimen obtained by the gun technique is very small and flaky, and hence inadequate for mechanical properties measurements. On the other hand if the material is forced to yield a continuous speci- men by the piston and anvil technique, it is probable that some plastic deformation occurs during the quench. A novel method for rapid quenching of a liquid metal or alloy, the "torsion-catapult", has been devised by Roberge and Herman9 at the University of Pennsylvania. In the apparatus the melt is thrown out of a curved furnace by a catapult and impinges on a copper substrate. The apparatus has the advantage of producing a continuous foil which is relatively large in size and of a quality suitable for the measurements of mechanical properties. The quenching rate is estimated to be of the order of l05 to l06 ºC per sec, (comparable to rates achieved by the piston and anvil technique). In selecting an alloy to be studied we were made aware of the fact that gold was believed to be "insoluble" in in and consequently age hardening in the A1-Au system appeared to be interesting. Quite recently Heirnendahl13-15 revealed that the solid solubility, as determined by transmission electron microscopy, was 0.3 wt pct Au at 640°C and 0.25 wt pct Au at 600°C, decreasing with decreasing temperature. In an A1-0.2 pct Au alloy after quenching from a solution treating temperature of 600°C the yield stress was 2 kg per sq mm, and it increased up to 6 kg per sq mm after aging for 1 to 10 hr at 200°C. The precipitation occurred in the form of platelike particles mainly on (100) matrix planes. The intermediate phase n', the equilibrium phase n (AuAl2), and lattice relationships between both precipitates and the matrix were also investigated by electron microscopy. One of the purposes of the present research is to determine whether or not the solid solubility in this system, in which gold has a very small solubility in

Jan 1, 1970

[Executive HENRY A. BUEHLER, Chairman ERLE V. DAVELER EDGAR RICHARD JOHN M. LOVEJOY WILLIAM WRAITH J. V. W. REYNDERS, Consultant Finance HENRY KRUMB, Chairman E. E. ELLIS PAUL D. MERICA H. G. MOULTON, Consultant]

Jan 1, 1936

By Martin Weinstein

A technique is described for preparing finegrained lead telluride by ultrasonic agitation of a solidifying melt. Material prepared by this technique is dense and chemically homogeneous. N-type PbTe, containing 0.03 mole pct PbIz, has been made and its thermoelecCric Properties have been measured as a function of temperature. For comparison, the properties of similarly doped PbTe made by cold pressing and sintering, and by extrusion, have also been measured. The ultrasonically prepared material compares favorably with the others in its thermoelectric-efficiency factor. Comparison of compressive-flow curves for the three kinds of PbTe show that the ulhasonically prepared material has much superior ductility. The cleavage strength of the ultrasonic material is related to the grain size, D, by the Petch relation:Extrapolation to infinite grain diameter yields a fracture strength of 5000 psi for single-crystal PbTe. WHEN metals and semiconductors solidify in a mold they normally assume one of three cast structures illustrated in Fig. 1.' Solidification in a casting starts at the mold walls where a large number of fine crystals of random orientation can be nucleated to form the chill zone. Because of the anisot-ropy of the growth rate, those crystals whose direction of maximum linear growth is parallel to that of the heat flow grow faster and crowd out the crystals of less favorable orientation. A second zone, having a preferred orientation, called the columnar zone, thus forms adjacent to the chill zone. The speed of growth of the columnar grains will depend, in the case of limited undercooling of the melt, on the rate at which heat can be abstracted. The columnar zone can extend to the center of the casting, Fig. l(a), but it is frequently followed, in solid-solution alloys, by another zone of equiaxed randomly oriented grains in the central portion of the casting, Fig. l(b). The equiaxed structure in Fig. l(c) represents the completely grain-refined case where the equiaxed grain size is small. The third type of structure is the most desirable because it imparts a somewhat higher strength for all except high-temperature applications, it reduces segregation of the doping constituent, and it reduces the possibility of hot tearing (the separation of grains due to the melting of a low-melting point constituent in the grain boundaries). In order to obtain fine-grained castings, the nu-cleation frequency must be increased and grain growth must be restricted. Various techniques have been employed for obtaining this end, namely: rapid cooling, vibration, and inoculation of the melt. The success of these techniques depends upon the characteristics of the metal species and on factors controlled by heat transfer through the crucible walls. Recent studies2" have shown that the application of ultrasonic energy to the solidifying ingot is an extremely powerful tool in the improvement of the crystalline structure of metallic castings. Both the mechanical properties and homogeneity of the ingots are improved. Ultrasonic oscillations may affect the crystallization process by 1) permitting subcritical nuclei to agglomerate and thus form nuclei of sufficient size to cause crystallization, 2) changing the state of surface adsorption of various catalysts found in the liquid melt, 3) breaking pieces of solid from the solidified surface near the supercooled region thereby increasing the number of possible nuclei, 4) causing temperature fluctuations to occur in certain parts of the melt thereby increasing the supercooling at specific points in the liquid, and 5) decreasing the critical nucleus size by increasing the pressure at specific points in the melt.' Various investigators have concluded that the effectiveness of the ultrasonic oscillations results from cavitation which disrupts the growing solid-liquid interface The present paper describes the application of ultrasonic oscillations to the crystallization of the semiconductor N-type PbTe. The purpose of this study is to prepare crystalline

Jan 1, 1964

By Jeffrey N. Schuyler

In order to implement the most efficient and cost-effective hydraulic fracturing stimulation treatment within a particular region, a thorough understanding of the in-situ stress state and rock properties is paramount (Smith et al., 1978; Warpinski et al., 1982). Several studies conducted in order to "characterize" formations have provided invaluable insight into the relationship between lithologic properties, depth, in-situ stress magnitude and hydraulic fracture orientation. These studies have substantiated that at shallow depths, rock properties such as tensile strength and permeability can exert a substantial influence on the geometry of an induced hydraulic fracture. In turn, these "directional properties" can be related to existing geologic conditions during the time of deposition or major diagenetic alteration of the rock body. As the depth of the "payzone" increases, the role of the in-situ stresses and therefore the prevailing tectonic conditions becomes the dominant factor in determining fracture geometry. However, reservoir properties cannot be ignored. The porosity, permeability, pervasive fabric element and directional elastic properties can have a significant influence on the success of those tests conducted to measure the in-situ stresses either directly or through secondary observations... for instance, pore-pressure effects on measurements of in-situ stress. The purpose of this paper is to provide, through the use of appropriate field and laboratory examples, a more thorough understanding of in-situ stresses, rock properties and their integrated effect on hydraulic fracture properties. In addition to highlighting and expanding the wide body of existing literature, the case studies cited are designed to encourage mutual transfer of technology from petroleum-related, rock-mechanics efforts to other disciplines.

Jan 1, 1984

By J. B. Scott, J. S. Nelson, G. H. Kruse, W. S. Johnson, K. L. Zerneke

The economics of pressure tunnel design emphasize the utmost utilization of the least expensive pressure-resisting material available, namely, the rock surrounding the tunnel. A major difficulty in the design is the problem of transferring internal hydraulic pressure to the rock through a tunnel lining or membrane provided to maintain watertight conditions. The lining is necessary not only to prevent water loss, but to prevent the diffusion of water at high pressure through joints and fractures beyond the confines of the tunnel, an occurrence which could ultimately affect the stability of the rock mass through which the tunnel passes. Because of its toughness and ability to bridge localized areas of weakness, steel is used for a lining material whenever high internal pressures are involved. The steel lining is coupled to the surrounding rock mass through an annular ring of concrete backfill. It is paradoxical that the steel lining, needed primarily to assure water tightness, must of necessity be incorporated into the structure as a major pressure-resisting component, not to augment the bearing capacity of the concrete and rock, but to limit the strain for the safety and preservation of the steel lining itself. With the deformation modulus of the steel so much greater than that of the rock, the liner approaches its yield strength before the load capacity of the rock can be fully mobilized. An economical determination of plate thickness for steel liners is therefore dependent upon measurement of the properties of the surround-

Jan 1, 1970

By R. W. Jordan, J. Winter, A. J. Goldman

Kirkendall diffusion of copper and nickel atoms across the bond interfaces, as well as oxygen diffusion in the core to the interfaces, are the mechanisms which control the variation in bond strength with annealing time at 1600°to 1800°F in the cupro-nickel clad copper Mint composite. The unequal mass transfer resulting from the high diffusion rate of copper in cupro-nickel compared with that of nickel in copper caused void formation in the core. Small voids also formed in the cladding after short annealing times. These may have been nucleated by nickel oxide particles which are formed by the dissociation of the cuprous oxide in the core and the movement of oxygen to the cupro-nickel interfaces. The bond strength drops to very low values for annealing time up to 3 hr when the void density is greatest. The increase in bond strength after 16 to 72 hr at 1600°F is a result of the decrease in the void density in the cupro-nickel cladding and the growth of grains across the interface. The void density decrease is attributable to grain boundary diffusion of vacancies to the surface. The abnormally large grains in the copper preclude a similar process from taking place in the core. THE solution to many engineering materials problems that cannot be satisfied by using a single metal or alloy is often attained by combining two or more metals in such a way that each component performs a different function, while the composite meets the overall requirements. The Coinage Act of 1965 authorized a changeover from the traditional 90 Ag-10 Cu dimes and quarters to a bimetallic laminate of 75 Cu-25 Ni clad on a copper core. Economic considerations as well as physical, chemical, and mechanical properties provided a basis for the selection of this composite as a substitute for the silver-bearing alloy. An extensive survey of alloys suitable for use as coinage was prepared by Battelle Memorial Institute for the U.S. Mint.1 It was found that the cupro-nickel/cop-per/cupro-nickel composite satisfied the required color, density, mechanical properties, corrosion resistance, electrical properties, and magnetic properties to make it completely acceptable to the general public and the vending machine industry. This investigation is part of a program to determine the feasibility of reclaiming composite scrap by thermally degrading the bond strength of the cupro-nickel clad copper laminate. The composite exhibits bond degradation and subsequent bond improvement during annealing in the temperature range 1600" to 1800°F. A study of the operative diffusion processes and the resultant structural changes was made in order to explain the observed variations in bond strength with annealing time. EXPERIMENTAL PROCEDURES AND RESULTS Bond Degradation. A measurement of the forces required to peel the cupro-nickel cladding from the

Jan 1, 1969

By R. B. Full

DURING the summer of 1949, the United Nations Scientific Conference on the Conservation and Utilization of Resources met at Lake Success. As summed up by one writer, the purpose was: "That everyone will try to learn how to feed more people from an acre of land." That objective is a stimulus to the phosphate rock industry as well as other industries. Phosphate rock was mined first in the Canadian province of Quebec where it was found as an apatite in pockets. In 1863, mining began near the Rideau Canal, first in open trenches and quarries until shafts were sunk. These operations were difficult since hard rock had to be drilled and blasted. Steam was the source of power. The phosphate rock was hand-selected and recovery ranged from 6 to 10 pct, averaging 70 pct to 85 pct bpl (bone phosphate of lime). Costs, f.O.b. Montreal, were $14 a ton, and selling prices averaged $17 a ton. In 1885, about 29,-000 tons were sold on this basis, but by 1892 the output fell to 8000 tons at an average price of $15 a ton at Montreal. South Carolina Deposits Phosphate rock was first discovered in South Carolina in 1837, but a mining company was not formed until 1867. It was immediately successful, and the industry continued to develop and ship an increased tonnage of land and river rock, shipments increasing from approximately 20,000 tons in 1868 to 537,000 tons in 1890, when the shipments began to decrease. In 1892 only 350,000 tons were shipped. In this field there were two types of deposits: land rock and river rock. More land rock tonnage was mined until about 1887 when river rock production began to equal it. The land rock was mined adjacent to and in the river marshes by pick, shovel, and wheelbarrow. Each worker dug daily a space 6 ft wide, 15 ft long and 6 ft deep, which was overburden, and then loaded about 3 cu yd of phosphate rock into wheelbarrows. His helper would wheel the barrows to small steam railroads up to 250 ft distant. Water was kept from the pits by steam pumps connected to railway cars. The phosphate rock was loaded into railroad cars, hauled and dumped into a log washer to which water was added, and run over trommel screens to eliminate the clay and loose sand. Steam shovels for loading were introduced about 1891. River rock was mined by floating dipper dredges and at low tide was loaded into barges by laborers using oyster tongs, the large lumps being hand-loaded. Barges and bateaus were unloaded by wheelbarrows which were wheeled to the same type of land rock washers. The washer product was piled with stacked pine cordwood in alternate layers and fired for drying. Usually this was done under sheds along the river bank. The dried rock then was transferred to ships, usually three or four-masted schooners. Cost of production of both land and river rock, including $1 a ton royalty paid to the state for state-owned property, was approximately $4.25 a ton averaging 60 pct bpl. The selling price was approximately $7 a ton f.O.b. In 1886 the courts handed down a decision permitting anyone to mine, and many additional companies were organized immediately. As a result, the selling price was lowered to a profit margin of 50Ø or less per ton. The South Carolina mines were eventually shut down when a more profitable source of phosphate rock was discovered in Florida. Florida Deposits Phosphate rock was discovered in Florida in 1882, and in 1883 a small quarry was opened near Hawthorne. In 1886 phosphate rock of good grade was discovered on Peace River, and the Arcadia Phosphate Co. was formed. In 1888 the company began shipments amounting to 3000 tons that year. During the latter part of 1888, hard-rock phosphate was discovered near Dunnellon. Exploration extended rapidly, and deposits of hard-rock phosphate were mined over a wide area so that shortly after 1900

Jan 1, 1952

By William D. Manly, John Towers, Paul A. Beck

RECENT work on grain growth in high purity aluminum and in a solid solution type alloy of aluminum and magnesium' showed that the isothermal increase of the average grain diameter D with time follows the equation [D = K(to + A)-Eq I] Here [to] is that portion of the total annealing time [t], which is available for grain growth, i.e. the annealing time less the time necessary for complete recrystallization. The parameters A and n depend only on the temperature. A has the dimension of time, and is usually of the same order of magnitude as the time for recrystallization: R. In some instances R may be substituted for A in Eq I. This is the case for example at long periods of annealing or at high temperatures, where both A and R become small in comparison with t. In such instances Eq I is simplified to [D-K-tnEq2] For high purity aluminum the exponent n increases in the ratio of about 1 to 5 in the temperature range of 350° to 600°C. 70-30 brass has been long known to exhibit grain growth of the continuous type, such as occurs in pure metals. For this reason, it was of interest to determine whether grain growth in brass also follows Eq I and 2 as it does in aluminum. Isothermal grain growth data for 70-30 brass were published in recent years by R. S. French2 and by H. L. Walker3 Fig I shows a log D vs. log t plot of French's data, together with the 500, 600 and 100°C data by Walker for 42.8 pct reduction by rolling. In such a log D vs. log t plot Eq 2 corresponds to a straight line with a slope of n. As seen in Fig I, the data of French and the 600°C data of Walker can be represented by straight lines. However, the 500 and 700°C data of Walker give curved lines and the average slope of his 500°C line is very different from the slope of the line representing French's data for the same temperature. Furthermore the curvature of the 700°C line suggests a tendency for grain growth to stop after 8 hr. If confirmed, this would constitute a definite deviation from Eq 2, not explainable on the basis of the specimen thickness effect found in high purity aluminum.1 Walker's specimens were 0.125 in., i.e. 3.18 mm thick, while the deviation occurs at a grain size of approximately 0.4 mm. A further point of divergence arose recently, when J. E. Burke suggested4 on the basis of Walker's data, that, instead of Eq 2, grain growth in 70-30 brass follows the equation [D-D. =K• t,Eq3] Here D, is the grain size as recrystallized at the temperature in question. Although it was possible to show5 that, for pure aluminum, for which isothermal grain growth has been carefully investigated, Eq 3 is incompatible with the experimental facts, the situation remained somewhat obscure with respect to 70-30 brass. In view of the discrepancies between the

Jan 1, 1948

By R. C. McFarlane, T. D. Mueller, J. E. Walstrom

In evaluating uncertainty, experiments are usually performed repeatedly and then conclusions are drawn from the distribution of results. With the advent of high-speed electronic computers, it is possible to perform experiments using mathematical models constructed to simulate complex experiments or operations. Statistical methods are then applied to the results of the simulated experiments. This procedure forms the busis of this paper. Demonstrated is the need for properly accounting for uncertainty in petroleum engineering problems. How uncertainty affects solutions is evaluated in three example illustrations. The method used to evaluate uncertainty in petroleum engineering studies is the Monte Carlo simulation procedure.'-" INTRODUCTION The solution to most technical problems may be derived from interrelationships among several quantities called variables or parameters. There may be only a few variables or several hundred. Interrelationships among parameters may be explicit or implicit, well established or only approximate. Some variables that fully or partially depend on the magnitude of others are called dependent variables. Input variables for most practical problems are not precisely known; there is usually an uncertainty in their value. The degree of uncertainty may vary from one variable to another. Variables that are known accurately are called determinates.' For instance, the gravity of crude obtained from a particular pool may be known precisely, and therefore is a determinate. The degree of precision with which a quantity can be determined increases as data describing the pool are accumulated during the development of the field and the producing life of the pool. The uncertainty of a parameter may result from difficulty in directly and accurately measuring the quantity. This is particularly true of the physical reservoir parameters which, at best, can only be sampled at various points, and which are subject to errors caused by presence of the borehole and borehole fluid or by changes that occur during the transfer of rock and its fluids to laboratory temperature and pressure conditions. Uncertainty may also result in attempting to predict future parameter values. This type of uncertainty is particularly evident in investment analyses involving future costs, prices, sales volumes and product demand. Uncertainty in the solution to investment problems is often called risk, and its study is called risk analysis.' Uncertainty also enters into biological and sociological analyses in which indeterminate factors are often important due to limited control of the experimental material. It is customary, in evaluating uncertainty, to perform repeated experiments and to draw conclusions from the distribution of the results of these experiments. With the advent of the high-speed electronic computer, it is possible to construct mathematical models which simulate complex experiments or operations and to perform the experiments repeatedly, utilizing the models. Statistical methods are then applied to the results of the simulated experiments This method forms the basis of the investigation reported here. PROBABILITY DISTRIBUTIONS FOR VARIABLES The uncertainty in the value of a variable may be indicated by a probabilistic description accomplished by expressing the quantity by a probability distribution. Many recognized probability distributions can be used to describe physical quantities. Recent studies used various types of distributions to describe core analysis data.',' However, for the examples in this paper, the uniform and triangular distributions are believed to reasonably approximate the data used (Fig. 1). The uniform distribution confines the variable between an upper and a lower limit. The variable may lie anywhere between the two limits. This distribution is used when no one range of values for a variable is more probable than any other, but information or intuitive reasoning indicates the variable will lie somewhere between the chosen limits. The triangular distribution is used for a variable when more data are available to indicate a central tendency of distribution. This allows postulating a "most likely" value to the distribution and upper and lower limits. In this case, as for the uniform distribution, the variable is not expected to assume a value less than the lower limit or greater than the upper limit. However, with improved quality of data it can be postulated that the variable will tend to assume a value close to the most likely value, and that there will be a decreasing probability for values away from the most likely value. The area under either of these probability distributions is equal to unity since it is assumed that there is a 100 percent probability that the variable will lie somewhere under the curve. An ordinate erected at any particular value of the variable divides the area under the curve into two parts: the area to the left of the ordinate represents the probability that the value of the variable will be equal to or less than the value of the variable at the position of the ordinate, and vice versa. The probability is zero that the variable will have any specific deterministic value. If two ordinates are drawn for any two values of the variable, the probability that the variables will have a value lying between these ordinates is equal to the area under the curve lying between the ordinates.

INTRODUCTION The regional characteristics of porphyry copper deposits in South America southward from Pantanos and Pegadorcito, Columbia, will be summarized. The age of formation of deposits spans the period from the Permian to the present. Where possible, the general characteristics and the individual structural features of the deposits are integrated into the plate tectonic model. Individual deposits cited in this chapter, located in Fig. 1, are the best known and most fully described, and form the Andean copper belt (Peterson, 1958). Smaller porphyry copper deposits fall both east and west of the line of large, high grade deposits (e.g., Chuquicamata and Toquepala) that make up the spine of this belt. Most of those smaller deposits (e.g., Mi Vida [Koukharsky and Mirre, 19761) are omitted from Fig. 1 and Tables 1 and 2, however. Neither the Andean orogen nor the individual deposits within it are as well de- scribed in the literature as are their counter- parts in the Cordilleran orogen of North America. Therefore, generalizations relying on regional geologic mapping, geophysics, and isotopic geochemistry lack details pertinent to this type of deposit in the Cordilleran orogen. The South American porphyry copper province has been described by Hollister ( 1974) to include most of the Andean orogen excepting the tin province of Bolivia. Porphyry copper deposits have not been commonly found within the tin belt, although copper-tin (e.g., San Rafael, Peru) and copper-tungsten (e.g., Llamuco, Chile) de- posits are known. James (1971) shows the depth to the Moho to be appreciably greater where the tin belt exists, but disclaims any genetic significance from the coincident appearance of the tin-tungsten province and the inhibition of porphyry copper development where the sialic crust thickens. Dates on tin mineralization in this belt (Clark and Farrar, 1973) are similar to some dates for porphyry copper mineralization known else- where in the Andean orogen. It seems that some mechanism is needed to explain the geographic separation of porphyry copper- molybdenum and simultaneous tin-tungsten- molybdenum metallization within the same tectonic system and appearing at similar distances from the trench. The thickened crust of the tin belt is one of the few known differences. Tables 1 and 2 list some of the most important porphyry copper deposits explored to date, but do not include Antaminas, Peru. or a number of other large skarn deposits

Jan 1, 1978

By F. A. Forward, A. H. Ross, J. Halpern

IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to +15oC. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO3 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi O2. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1958

NORTH AMERICA ALASKA Anchorage.-Strandberg, H. College.-Barber, R. J. Burns, W. T. Henricksen, R. Henton, H. M. Joesting. H. R. Comet.-Albertson, F. E. Douglas.-Cahill, W. E. Carlson, L. Fairbanks.-Andregg. J. N. Coats. R. R.

Jan 1, 1938

By L. Adler

Any design of a mine roof in bedded deposits which ignores differential deflections at the supports can quickly lead to dangerous overstressing. As illustrated by the typical case presented on page 1029, if one support deflects only 0.1 in. more than its neighbor, stresses 50 pct higher than anticipated will result. Previous studies1-3 have assumed that the mine roof acts like a beam clamped at both ends, with no deflection or slope' at the supports (Fig. 1). Essentially this assumes:5* ?A = ?, = ?b and dA = dB = 0. However, a host of conditions can cause differential sag or deflection at one support, and even an apparently trivial deviation can have major consequences in the beam: variations in spacing, size, and material of supports; local settlement due to floor heaving or lower mine openings; non-uniformity in wedging or bolt tensioning.8 In one particular instance concrete pillars, poured in place, shrank away from the roof upon setting.' When understood and controlled, differential sag becomes a definite advantage, permitting the transfer of loads from one support to another. Where one support is a bolt or prop and the other a pillar or rib, the load on the former can be reduced while the load on the pillar or rib is increased. This means two things: 1) savings can be effected by using smaller artificial supports such as props and bolts and 2) loads can be increased in the rib to induce eventual failure for longwall caving. In this last respect, another factor underlying coal bumps becomes understandable. The design of a mine roof by beam theory assumes that when a bedded formation is homogeneous, iso-tropic, and elastic, it will act like a uniformly loaded beam, fixed or clamped at both ends,6 s in Fig. 1.'" These are important assumptions. The uniform load is the weight of the beam itself or its body load. For a beam of unit width, this load becomes per foot: w = yhb. w = uniform load y = specific weight, lb per ft3 h = depth or thickness of beam, ft b = width of beam, ft Since b = 1, w - yh [ 1 ] A beam fixed at both supports is statically indeterminate to the second degree, that is, two equations in addition to those for static equilibrium are required to determine the reactions at the supports. These equations result from the geometry. From statistics: ^F,= 0;RA + RB — wL = 0 [2] wU S,M0 = 0 ; MB H------------MA — RBL = 0 [3] it Using superposition in which the left support is kept intact and the right one resolved into an active force and moment, we obtain from Fig. 2:" ?b = ?m + ? b2 + ?B3 = 0 dB = dB1 + dB2 + dB3 / wU Ma RBL \ V d°=(-r+-2—r)-zr [5] Where: Subscripts refer to position on axis of beam R = force, lb M = moment, ft-lb w = uniformly distributed load, lb per ft L = span, ft 0 = slope, radians d = deflection, ft E = Young's Modulus, lb per ft" 1 = Moment of inertia about the neutral axis, ft4 Solving Eqs. 2 through 5 for the four unknown reactions, we obtain: 2 L3 Fig. 3 is obtained by plotting MA and M, vs d, and then plotting RA and R, vs d, and adjusting their scales to coincide with MA and M, vs d,. It should be noted in Eqs. 6 and 7 that as dB increases, MA increases the same amount that Mn decreases. Eqs. 8 and 9 show a similar relationship between RA and R,. Proof that MA is the maximum absolute moment occurring in the beam is as follows: where M, = moment at x wx-When where M,., = maximum positive moment Eqs. 6 and 8 into above: For small dn: MA> M,,,

Jan 1, 1960

TO THE BOARD OF DIRECTORS AND THE MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -It is pleasant to be able to report that the year just closed has been a prosperous and successful one for the Institute As is shown by the reports of the Treasurer and the Finance Committee, the business affairs of this organization are in excellent condition With property valued at more than three-quarters of a million dollars, and with con¬siderable sums in various funds and endowments, it is possible to spend on each member of whatever class $22 65 each year, more than the maxi¬mum amount of dues received from any one, and substantially twice the average amount, $10.94, received from all To do this has required close management and a strict regard for our limitations In 1926, when the Budget was made up, the estimated expenditures for the work which it was felt the Institute must do exceeded the estimated receipts by some $14,000. At the close of the year, despite a` number of unexpected decreases in receipts, it had proved possible to accomplish substantially all the work laid out and close the books with the usual transfer of initia¬tion fees to the General Reserve, and still only reduce the cash balance $2,074 54. This was made possible by the hearty and loyal cooperation of the whole staff of employees and the extremely large amount of gratui¬tous service rendered by the officers, the members of the Divisions and technical Committees, and the membership generally Even so it was impossible, because of limitations of funds, to undertake many things it is highly desirable for the Institute to do, and it was necessary to refuse the publication of important papers and committee studies, because of the lack of funds.

Jan 1, 1923

Jan 1, 1887

By W. A. Cole, E. L. Derby, J. F. Wolff

Exploration of Lake Superior iron ores is done principally by drilling. The soft iron ores are churn drilled and the harder ores are diamond drilled. The churn drill used is the Mesabi type and its operation should be described as "water jetting." The drill rods are washed down by the combination action of the water jetting from the bit at the lower end of the rods and the churning motion given the line of rods. The water, which is forced down through the rods, comes up between the wash rods and the casing, bringing the choppings to the surface. It is caught in three or more barrels, each of which has a stoppered hole 8-10 in. from the bottom. These barrels are successively filled, allowed to settle, and drained to the hole, until the desired depth is drilled. The sediment from each barrel is transferred to a settling tub in which it is allowed to settle; the water is then drawn off and the wet sample is collected and dried. The number of barrels used depends on the character of the ore. For example, when drilling sandy ores, all the wash water is caught and settled for the proper length of time without refilling any of the barrels. Thus, the sediment held below the stoppered hole in any one barrel is not disturbed. The casing is kept as near the bottom of the hole as practicable to prevent the caving of the hole from jeopardizing the sample. While the casing is being driven down and the hole is being washed clean after casing, the return water is not run into the sample barrels. In exploratory work in the harder formations, where the diamond drill is used, the sample comprises both core and cuttings. The care given in handling and preserving the core depends on the importance that may be attached to certain characteristic strata in different formations. The following instructions for the care of core samples are issued by the Ogle-bay Norton Co. for diamond drill work done for them on the Gogebic Range of Michigan:

Jan 1, 1925

G. A. ROUSH,* South Bethlehem, Pa. (written discussion?).-Mr. Frey is correct in his impression that ice floats, but "frazil" ice happens to be the exception to the rule. The requirements for the formation of

Jan 12, 1919

By U. K. Custred, E. W. Long, V. R. Degner

In 1973, the United States production of marketable phosphate rock set a record in excess of 42 million tons. This production rate is expected to continue to increase, due to the growing international requirement for fertilizer, at a rate exceeding 5% per year well into 1977. One approach towards increasing plant production capacity to meet the growing demand is through large-capacity flotation cells, provided they achieve metallurgical performance comparable to existing smaller cells. A 9-month evaluation test program recently completed at the Haynsworth mine at Bradley, Fla., demonstrated the feasibility of achieving economically acceptable concentrate grade and recovery levels using large, high-capacity flotation cells. The composition of the feed to the Haynsworth beneficiation plant is a typical Florida pebble phosphate matrix composed of phosphorite pebbles ranging in size from approximately 1-1/2 in. down to 150 mesh and intimately associated with a mixture of clay and sand (essentially silica). The feed contains approximately 22 to 28% phosphate reporting as tricalcium phosphate, Ca3 (PO,) 2, or "bone phosphate of lime" (BPL). The flotation section utilizes the double-float procedure typical of Florida plants. The phosphate is first floated away from the silica in the rougher circuit, using crude fatty acid, ammonia, and fuel oil or kerosene. Rougher conditioning is accomplished at 60 to 70% pulp solids with sufficient ammonia added to raise the pH to 9 to 9.5. Following coarse and fine rougher flotation, the concentrate (overflow) streams are joined and conditioned (sulfuric acid cleaned and washed) prior to entering the cleaner circuit where an amine float (cationic reagent and kerosene added in the feed box; pH 7.3 to 7.8) is employed to float the silica. The feed to the coarse rougher circuit averages 29% +35 mesh while the fine rougher feed averages 10%+35 mesh. Primary attention was directed toward the large rougher cell performance (recovery and grade) on coarse feed during the Haynsworth evaluation program. Flotation Cell Test Program A row of three No. 120 size (300 cu ft) WEMCO flotation cells was installed in parallel with an existing air-cell row. The total installed volume of the large cell circuit was 900 cu ft and required a floor space of 306 sq ft. This compared to the air-cell total volume of 200 cu ft and 152 sq ft floor space. (Both floor areas include feed and tails hoppers but exclude walkways.) Fig. 1 is a schematic cross section of the large flotation cell showing the relative location of key mechanism elements. In operation, the rotor generates a fluid vortex extending up along the walls of the standpipe and creating a sufficient vacuum within its core to ingest air into the standpipe/rotor cavity through the air inlet duct. The ingested air mixes with the pulp, which has been recirculated through the false bottom and draft tube, in the rotor. Further mixing occurs as the air and pulp move radially outward from the rotor, finally passing through the disperser into the flotation cell. Flotation is accomplished outside the disperser, where phosphorite laden air bubbles rise and the remaining pulp recirculates down along the cell wall to the false bottom and draft tube. Large-flotation-cell performance is influenced by the ability of the mechanism to (1) circulate, or suspend, the solids in the pulp; (2) ingest air into the rotor cavity; and (3) mix the air and pulp effectively. The proper balance between pulp circulation and air ingestion is a key consideration in achieving good recovery in a course feed application. Large-flotation-cell pulp circulation and air transfer characteristics are significantly influenced by rotor speed and rotor submergence; therefore, these two operational parameters can be used to "optimize" a particular mill application. Fig. 2 maps the hydraulic performance of the WEMCO No. 120 size flotation cell. This map can be used to relate the cell operational parameters which influence metallurgical performance. At a given rotor speed, power intensity (i.e., pulp circulation) is seen to increase, and airflow decrease, as rotor submergence is increased. The inverse relation between power and airflow is due to the two-phase air-liquid mixture density reduction accompanying the increased airflow rate. For any fixed rotor submergence, the power intensity (i.e., fluid circulation) and airflow both increase as rotor speed is increased. The selection of these two mutually related operating conditions (i.e., rotor speed and submergence) was a key consideration in the Haynsworth evaluation program.

Jan 1, 1976

By W. A. Tiller

The unidirectional freezing of a semiinfinite liquid from one end has been treated by calculating the solute and temperature distributions in the liquid and solid phases with time, when the solid-liquid interface advances at a rate proportional to (time)lt2. The nucleation probability for new grain formation is calculated as a function of the constitutional and thermal properties of the alloy, the pouring conditions and the catalytic efficiency of the nucleating agents. The transition from columnar crystal formation to equiaxed crystal formation is assumed to occur at a critical nucleation frequency for a particular alloy and the quantitative dependence of the ratio (columnar zone length/equiaxed zone length) upon the freezing conditions has been predicted. The effects of (i) fluid flow in the liquid, (ii) heat transfer through a mold wall, and (iii) a finite ingot length, have been explicitly tveated as departures from ideality. These departures from ideality are found to have very important consequences on the ingot stmcture. In Part I&apos; of this series, a qualitative description of the general ingot structure was developed. The factors that determine i) the ratio of the equiaxed zone length to columnar zone length and ii) the grain sizes in these zones, were discussed. In the present paper, topic (i) will be treated quantitatively, and it is intended that topic (ii) will be treated quantitatively in Part 111. The complete treatment has been split in this manner for ease of development and coherency of presentation. The treatments are quite mathematical in nature and, although some of the conclusions to Part 11 depend upon the treatment presented in Part 111, it was felt that the intended audience would find the material more readable and more useful in its present form. To this same end, it seems worthwhile to reiterate some of the qualitative aspects of grain nucleation during ingot solidification before embarking on the mathematical description. QUALITATIVE ANALYSIS In the conventional method of casting, a liquid alloy with a certain degree of superheat is poured into a mold. The outer rim of liquid metal cools rapidly to the liquidus temperature of the alloy and begins to undercool. As the degree of undercooling increases, nuclei of solid begin to form in this chill layer, this nucleation being catalyzed by certain heterogeneous particles in the liquid. The grains in the chill layer which are generally of random orientation, begin to grow inwards because of heat conduction through the mold. The grains usually develop a columnar shape since the frequency of nucleation of new grains in the liquid ahead of the advancing interface is generally insufficient to seriously impede the growth of the original grains. Due to the slow diffusion rate of solute in the liquid, a solute distribution is formed in the liquid adjacent to the interface which is either an excess or a depletion if the partition coefficient, ko, of the solute is < 1 or > 1, respectively. Thus, the liquidus temperature of the liquid adjacent to the interface is a function of position. The actual temperature in the liquid is also a function of position and the temperature gradient at the interface decreases as the interface moves away from the mold wall. Since the rate of advance of the interface decreases with time, the equilibrium temperature distributions and the actual temperature distributions as a function of interface position, X, can be illustrated as in Fig. 1. Thus, a region of liquid may exist in which the actual temperature is below the liquidus temperature. This liquid is contitutionally supercooled and therefore unstable with respect to the nucleation of new grains. Now, since the supercooling in Fig. 1 increases as the interface moves further away from the mold wall, the nucleation rate of new grains will increase. When the nuclea-

Jan 1, 1962

By A. S. Odeh

The mechanism of two-phase flow in porous media has been a subject of wide controversy. One of the properties essential for understanding the dynamic behavior of two-phase flow is relalive permeability. Relative permeability to a certain phase is defined as the ratio of the effective permeability of that phase to its permeability when it is the only fluid present and powing. In this research, a theoretical analysis was made to determine the effect of viscosity ratio between the non-wetting and the wetting phase on relative permeability. Experimental work was conducted to test the validity of the derived equations. The experiment was conducted on four natural cores. Four oils were used as the non-wetting phases with a viscosity range of 0.42 to 71.30 cp and two wetting phases with a viscosity range of 0.86 to 0.96 cp. Oil and bring were made to flow simultaneously at various ratios, and relative permeability curves were constructed. A total of eight relative pertileability cycles representing eight viscosity ratios were run oil each sample. It was found that relative permeability to the non-~cletting phase varies with viscosity ratio. The relative effect of this variation on relative permeability values was a function of the sample&apos;s single-phase permeability, decreasing with its increase. It was concluded that, for .samples of single-phase permeability over I darcy. the effect of viscosity ratio could be disregarded, and relative permeability would be, in effect, a function of satrtration only. INTRODUCTION Two-phase as well as multiphase flow occurs in many fields of science. This type of flow is of particular interest in petroleum production. The knowledge of relative permeability, which describes the dynamic behavior of two-phasc as well as multiphase flow, is essential for solution of problems arising in that field. Thc relative permeability ot a porous medium to a given phase in multiphase flow. is generally considered to be only a function of the saturation of that phase, independent of the properties of fluids involved and ranging in value from zero to unity. Work by Leverett&apos; and Leverett and Lewis&apos; apparently supports this concept. In his experiments Leverett used a clean, packed unconsolidated sand of high permeability (3.2 to 6.2 darcies) with two phases (water and oil) flowing and a viscosity ratio range of 0.057 to 90.0. His results showed that the wide range of viscosity had practically no effect on relative permeability-saturation relationship. Recently accumulated evidence from work performed by several laboratories and a paper by Nowak and Krueger,2 in which relative permeability to oil of a few core samples in the presence of interstitial water was considerably greater than single-phase permeability to water, cast some doubt on the conclusions reached by Leverett&apos; and subscribed to by a large number of individuals in the oil industry. One explanation advanced to explain this behavior states that it is caused by the variable extent of hydra-tion of clay minerals present in the sand. The greater the water saturation, the greater will be the area of contact between water and clay minerals; therefore, the greater will be the extent of swelling with corresponding reduction in permeability. Yuster4 presents another explanation for the recently accumulated evidence. Utilizing Poiseuille&apos;s law, he analyzed concentric flow in a single capillary where the non-wetting phase flows in a cylindrical portion of the capillary and concentric with it. The wetting phase flows in the annulus between the non-wetting phase and the capillary wall. The equations obtained indicate that relative permeability to the non-wetting phase is a function of saturation and viscosity ratio. Although Yuster&apos;s equations show that fractional rel-ative permeability to oil could be greater than unity, as was indicated by the data of Nowak and Krueger,1 they failed to present an explanation to the experimental data of early investigators such as Leverett.1 Due to the importance of relative permeability in understanding the flow behavior of petroleum reservoir fluids, this work—theoretical as well as experimental —was undertaken to determine whether relative permeability is a function of saturation only as was concluded by Leverett1 or a function of saturation and viscosity ratio as was theorized by Yuster.4 THEORETICAL ANALYSIS An equation will be derived for the rate of oil flow through a porous medium that is initially filled with water. Based on this equation, an analytic expression for relative permeability will be developed. The porous medium will be assumed to consist of .straight circular capillaries of different radii. It will also be assumed that there are no interconnections among the capillaries and no mass transfer across the oil-water interface. Consider a porous sample initially saturated with a wetting phase (water). As a non-wetting phase (oil) is