Search Documents

By P. F. Gnirk

Consideration is given to creater formation with shallow, contained, chemical explosions in rock masses which exhibit different inherent physical and mechanical properties as determined by standard laboratory techniques. The primary purpose is to determine whether or not a simple but useful generalized correlation can be established between explosive crater formation and one or more common rock properties. Such a correlation could be beneficial in predicting with some degree of reliability the size of a crater which could be expected in a particular rock type for a given input of explosive energy. A series of crater formation experiments employing constant weight charges of Gelex 2 explosive was conducted in five submembers of the taconite formation at the eastern end of the Mesabi Range in northeastern Minnesota. Five mechanical and physical properties-unconfined tensile and compressive strengths, Young's modulus of elasticity, longitudinal wave velocity, and density-were determined by conventional laboratory techniques using core samples from the taconite submembers. Although insufficient data were obtained to warrant the use of mathematical methods in the determination of empirical relationships, the results provided a fairly strong indication that with an increase in magnitude of any one of the five rock properties definite decreases in the optimum crater volume and surface area occur. Furthermore, for a constant explosive energy input, the presence of bedding planes and joint systems in a rock mass influences the formation of craters in such a manner as to increase the volume of rock broken substantially above that expected from the same rock mass without joint systems and, in particular, without bedding planes.

Jan 1, 1968

By H Pray, H. W. Russell, Paul D. MILLER

It is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranu-lar corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels has been ably discussed by Bain and co-workers1-3 and by other investigator4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measuremerits, measurement of the degree of cracking produced on bending over a malldrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A.-1011 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. Experimental Method A small area of the steel under test is subjected to an anodic treatment in a cell that can be 'lamped Onto a a Or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring Or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8- diameter' The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941

By H. W. Russell, H Pray, Paul D. MILLER

It is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranu-lar corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels has been ably discussed by Bain and co-workers1-3 and by other investigator4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measuremerits, measurement of the degree of cracking produced on bending over a malldrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A.-1011 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. Experimental Method A small area of the steel under test is subjected to an anodic treatment in a cell that can be 'lamped Onto a a Or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring Or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8- diameter' The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941

By S. R. Goodman, Hsun Hu

The rolling texture of an 18-8 stainless steel (Type 304L or 304) has been found to change gradu -allv from the (110)[112] brass type to the (123)[412] copper type as the rolling temperature increases from 200° to 800°C. This texture transition is accompanied by a change in the stacking-fault frequencv or probability, similar to those found pre- In a series of previous publications, it was shown that the rolling texture of high-purity silver changes gradually from the brass type to the copper type with increasing temperature of deformati~n. A similar temperature dependence of rolling texture transition was found in electrolytic copper3—by lowering the temperature of deformation, the normally observed rolling texture of copper changed gradually viously in nonferrous fcc metals—the stacking-fault frequency decreases rapidly with the formation of the copper type texture. These results strongly indicate that the temperature dependence of copper type == brass type texture transition and its correlation with stacking-fault frequency is a general phenomenon in fcc lattices. to the brass type.* In both of these metals, the

Jan 1, 1964

By Robert J. Hite, Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table 1), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term potash originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first US patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 27.5 Mt K20 produced in the world in 1980 (Searls, 1981) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K20, a unit of measure which is neither a natural nor synthetic compound of potassium (1.0% K is equivalent to 1.2046% K2O). Geology Potassium, the seventh most abundant element in the earth's crust, is present in silicate minerals in igneous, sedimentary and metamorphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such deposits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of seawater or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D'Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in Table 1. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971). The structural basins within which marine evaporites occur are of two main types: (a) cratonic basins formed by broad epirogenic movements (for example, the Michigan Basin of the midwestern United States and the Permian Zechstein Basin of eastern Europe), and (b) grabens, commonly related to continental

Jan 1, 1983

By R. J. S. Brown, B. W. Ganison

A new logging method has been developed, based on measurement of the nuclear magnetism of formation fluids. The nuclear magnetism log (NML) is the only log that responds solely to formation fluids. It operates equally well in both oil-base and water-base muds and in empty holes, and can be used in all kinds of formations except strongly magnetic ones. Two separate NML measurements can be made, one of which provides a continuous formation fluid curve. This fluid curve is called the free fluid log (FFL) and is believed to indicate a minimum effective porosity in most formations. The FFL not only delineates fluid-containing zones, but provides an excellent correlation curve that can be obtained under conditions where conventional correlation logs are ineffective. Preliminary tests indicate that the second kind of NML measurement may help distinguish oil and water zones and provide information concerning permeability and wettability. (The FFL itself appears to provide some information on permeability.) The second kind of NML measurement requires stopping the logging tool for a short time opposite a zone of interest and taking more extensive NML data that can be displayed as nuclear magnetic relaxation curves. In some instances, oil and water saturations for the region immediately adjacent to the borehole can be read from these relaxation curves. INTRODUCTION In 1946, Bloch, Hansen and Packard and Purcell, Torrey and Pound3 independently announced the successful demonstration of the phenomenon of nuclear magnetic resonance. During the past 13 years, there have been many applications of nuclear magnetic resonance, including applications to the study of chemical structure and to the measurement of magnetic field strengths. Preliminary experiments on the feasibility of using nuclear magnetism measurements in well logging were made independently by California Research Corp. and Varian Assoc., the Varian work being sponsored by the Byron Jackson Tools, Inc. Since then a cooperative research program on nuclear magnetism logging has been carried out by the Byron Jackson Div. and Research Center of Borg-Warner Corp., and California Research Corp., subsidiary of Standard Oil Co. of California. The use of nuclear magnetism in well logging is of special interest because it offers a way of making direct measurements on the hydrogen in the formation fluids and not on the rock matrix. Within the past 1 1/2 years, successful measurements have been made with a research model logging tool in wells in California, Tex as, Utah, Louisiana and Wyoming. NUCLEAR MAGNETISM SIGNALS Polarization, Relaxation and Precession Many atomic nuclei possess magnetic moments and spins; that is, they are similar in some respects to bar-magnet and gyroscope combinations. Molecules and their nuclei are subject to thermal motion, which has a scrambling effect, tending to leave as many nuclear spins oriented in any one direction as in any other. However, if a magnetic field is applied, the magnetic nuclei tend to align in the direction of the field. The scrambling and aligning forces compete with each other, with the result that a few more spins are oriented parallel to the field than in other directions. This gives a net magnetization, or polarization, which is directly proportional to the strength of the applied magnetic field (aligning influence) and inversely proportional to the absolute temperature (scrambling influence). When the magnetic field in, or temperature of, a liquid sample containing protons is changed, the new equilibrium value of proton polarization is not established immediately but requires an amount of time which depends on the nature of the hydrogen-containing materials. The process of approaching the equilibrium value of polarization is called relaxation.'.' Polarization is a vector quantity, and the components parallel to and perpendicular to the magnetic field must be considered separately. Relaxation of the component parallel to the field is called "thermal relaxation", or "longitudinal relaxation", and the corresponding time for this component of non-equilibrium polarization to decay by a factor of e (natural log base) is denoted T. The relaxation of the perpendicular component is called "transverse relaxation", and the corresponding relaxation time is denoted T,. The potential energy of a magnet in a uniform field depends on the angle the magnet makes with the field; therefore, a change of the component of net polarization parallel to the magnetic field involves an exchange of energy between the spin system and the thermal motion of the molecules, leading to the term thermal relaxation for the relaxation of this component. Suppose we subject a sample to a strong magnetic field at right angles to the earth's field for a time greater than TI. A polarization, thus, is established at right an-

By T. M. Morris, F. M. Lewis, W. C. Lay, Gordon M. Bell

Part I of this chapter is concerned with the description of and metallurgical data pertaining to the flotation circuits used in the London mill of the Tennessee Copper Co., at Copperhill, Tenn. The ores treated at the London mill are massive complex sulfides, in which pyrrhotite and pyrite are the predominant minerals. Other sulfides are chalcopyrite and sphalerite; magnetite is also of economic value. The approximate mineralogical analysis of the ore is shown in Table 1. [ ] The chalcopyrite and sphalerite are closely associated with pyrrhotite as shown by the tracings of micrographs (Fig. I), which are representative of the mill feed. Fig. la illustrates the type of locking between pyrrhotite and chalcopyrite; Fig. lb illustrates the way in which sphalerite is attached. Thesephotographs indicate that it is not practical to break all of these attachments. Hence, in order to produce concentrates with satisfactory grades and recoveries, most of the locked chalcopyrite particles must be recovered into the copper concentrate, and the locked sphalerite-pyrrhotite particles must be separated from the iron concentrate. A copper concentrate, a zinc concentrate, and an iron concentrate are made. Typical metallurgical results are tabulated in Table 2. HISTORICAL In 1922 the London mill started as a copper concentrator, with a capacity of 300 tpd, and in 1926 an additional flotation circuit was added to recover the iron sulfide remaining in the copper tailing. In 1927 a zinc flotation circuit was installed between the copper and the iron flotation circuits. This procedure was not satisfactory because the iron recovery was low, due to the

Jan 1, 1962

By D. A. Summers, C. J. Haas, G. B. Clark, J. W. Brown

While significant advances have been made in excavation of rock, largely in improvements in drilling, blasting, loading, and haulage, conventional operations have been improved until little feasible increase in efficiency or rate of advance appears possible. Tunnel-boring machines have been developed which will excavate at rapid rates in soft to medium- hard rock. Hypervelocity impact is being intensively investigated as a possible means of cutting and breaking rock, as well as lasers, electric current, explosive drilling, high frequency vibration, etc. The current development and use of high-velocity small-diameter water jets, metallic jets, and projectiles of various materials involve ultra-high-pressure phenomena of fundamental interest. Rock disintegration by water jets has been investigated in the USSR for over a decade. Large-diameter jets of low velocity are used to mine coal, and high-velocity capillary jets will cut and break rocks under laboratory conditions. Velocity ranges for breaking and cutting are dependent upon rock and jet properties, and pulsed jets break some rocks more easily than continuous jets. Spectacular laboratory results have been reported for breakage of unconfined blocks of some types of rocks. Compressors, pressure multipliers, gas explosion chambers, and water cannons have been used to generate jets. Jet properties, such as continuity, unit pressure, total pressure, and stability have been measured. Results agree with theory, although the latter has been established only for relatively low-velocity flow. Diameter, speed of traversing, and frequency of pulsed jets affect rock response. Investigations in Britain have only recently begun consideration of harder rocks and higher velocities, although water jet cores have been found to be more continuous at lower velocities than previously believed. Lower limits of jet velocity for rock cutting were established for the rocks investigated.

Jan 1, 1970

By W. F. Schwedes, S. S. Rumsey

In order to realize the enconomics which would result in operating the mine pumps at the Chapin mine with electricity generated by water power, the Oliver Iron Mining Co. recently installed a hydro-electric plant at the upper Quinnesec Falls on the Menominee river, and constructed a transmission line to the mine.

Jan 1, 1915

By J. L. Huitt, S. R. Darin

The use of a partial monolayer of propping agent to obtain a high flow capacity for a hydraulically induced fracture is discussed. From the results of laboratory work it was shown that a modified form of the Kozeny-Carman relation could be used to describe the flow in the partial monolayer propped fracture. With equations presented in the paper, the density pattern of the propping agent (number of particles per unit of fracture surface) that results in the maximum flow capacity for the fracture can be determined. The maxitnum flow capacity obtained with a partial monolayer is often an order of magnitude greater than the flow capacity obtained in greater width fractures containing multilayers of the propping agent. INTRODUCTION One of the predominant factors controlling the success of a hydraulic fracturing operation is the propping of the fracture. The trend in hydraulic fracturing recently has been an increase in the ratio of propping agent-to-fluid. The primary purpose of this increased ratio is to sustain a propped fracture of greater width. It was shown in a recent study' that for some formations low concentrations of propping agent would result in "closing" or "healing" of the fracture. In some cases, in an effort to insure sufficient propping agent concentration, the fracturing operation is designed to obtain a pack of the propping agent in the fracture. The placing of a pack of propping agent in the fracture provides a fracture of maximum width; however, the width alone does not control the flow capacity of the fracture. The flow capacity is dependent on the permeability of the fracture, as well as the fracture width. Thus, increasing the permeability to obtain larger flow capacities is as important as obtaining a greater width fracture. By increasing the concentration and particle diameter of the propping agent, fractures of sufficient flow capacities are obtainable for effective well stimulation in a number of formations. However, in some of the recovery techniques, the fracture capacity obtained by commonly used practices in fracturing is inadequate. One such recovery technique is gravity drainage via a horizontal fracture placed near the base of the productive zone. For this recovery technique, the fracture capacity desired is usually one to two orders of magnitude greater than the fracture capacity normally obtained in fractures propped with the size of sand commonly used (20-40 mesh). By the use of particles of larger diameter, the permeability of a pack2 is increased; however, even a multilayer pack results in a fracture flow capacity lower than that desired for some formations. For example, a fracture of 1/4-in. width, packed with 8-12 mesh sand of about 2,000 darcies permeability, would result in a fracture flow capacity (permeability X fracture width) of only 40,000 md-ft. If the fracture flow capacity needed is an order of magnitude greater than that cited in the example, an approach different from the formation of a pack in the fracture is needed. One approach is a partial monolayer of large-diameter propping agent. In working with this type of fracture system, it was found that the flow problems were unique to the system; therefore, the study discussed in this paper was made. THEORY AND RELATED STUDIES Previous studies, although related to that described in this paper, have not pertained directly to the flow in a fracture propped with a partial monolayer of propping agent. However, studies such as flow between parallel plates,' flow in packed columns,' fracture flow capacity' and flow in simulated fractures reduce the scope of this flow problem considerably. A fracture propped with a partial monolayer of dropping agent may be considered to be between two extremes — between an open fracture and a bed of particles packed In a conduit of fracture geometry. Thus, it seems appropriate to review the extreme cases.

By W. H. Bassett, J. C. Bradley

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (I) Depth of deoxidation of copper heated in reducing gas is grealer the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this diflerence in depth of deoxidation is thai, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much more rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900" C.; that is, deoxidaion is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide presenx in the copper. In 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

By Ramesh Malhotra, Hubert E. (Deceased) Risser

THE WORLD Coal, as a source of energy and as a source of coke for the smelting of iron ore, has contributed significantly to the development of every major industrial nation of the world A number of other materials-oil, natural gas, wood, waste materials, water, and, in some applications, nuclear materials -can be used satisfactorily for the generation of heat and energy, but no generally acceptable and economic substitute has been found to supplant coke in iron ore smelting in conventional blast furnaces. In the development of many nations, coal provided the initial source of energy for industrialization Although coal provided more than 60% of the world's energy each year between 1902 and 1929, oil and natural gas have surpassed it as a source of energy in more recent years (Ref. 38, pp. 439, 441). Despite the rapid rise in importance of other fuels, a considerable amount of the total energy consumed is still supplied by coal. In 1972, coal supplied 32.1 % of the total world energy (Ref. 49, pp. 2-3). To produce this energy, 2.4 billion metric tons of coal were consumed-a 16.0% increase over the amount consumed in 1962. A further worldwide increase in the amount of coal used to supply energy is projected. According to Dr. Karlheinz Bund (Ref. 37, p 145), by the year 2000 world coal consumption could amount to 5 billion mt. Coal Resources and Production The world's coal resources are estimated to be about 10,872 billion mt. Of this amount, 1,297 billion mt are classified as measured reserves (Ref. 50, p. 57). In Table 13.A.1 the estimates of measured reserves and total resources, recent production, and the ratio of measured reserves to production of major coal-producing countries are shown. About 90% of the world's total coal resources are estimated to be in the USSR, the United States, and China. The United States ranks second in the world in coal resources, but in measured reserves, it ranks first. Because of the difference in rate at which available coal resources are being exploited, the ratio of measured reserves to actual production varies widely among areas and countries. France and East Germany have the lowest reserve to production ratios, 49.5 and 60.1, respectively. In Mexico, where currently less than 5 million mtpy of coal are produced, the ratio is 1257 For all countries producing more than 200 million mtpy of coal (except East Germany), the ratio ranges from 350 to 670. For the United States, the ratio is 669.7. In Table 13.A.2, distribution of the world's coal resources by area is shown. More than 97% of the total resources lie in the northern hemisphere, with Asia, including European USSR, having 63.4%. Only 1.9% of the total coal resources are estimat-

Jan 1, 1976

By John A. Prof. Church

ONE of the most striking phenomena connected with the mines on the Comstock lode is the extreme heat encountered in the lower levels. This heat is not due to the burning of candles, heat of the men, and decomposition of timbers, all intensified by bad ventilation, as was the case nearer the surface. It proceeds from the rock, which maintains constantly a temperature very much higher than the average of the atmosphere in Nevada. The heat of these mines is a matter of more than usual interest, for they are the only hot ones now worked in the United States, and both in the present temperature encountered and in the increase which is to be expected as greater depths are reached, they appear to surpass any foreign mines of which we have a record. Hot mines are known also in other countries, as in the tin and copper lodes of Wales, where one of the veins worked by the United Mines is known as the hot lode. It has springs which discharge water at a temperature of 116° Fahrenheit, the depth being 220 fathoms, or 1320 feet. The heat of the air in these workings is given at 100° to 113° Fahrenheit. The air is bad, and the heat in the drifts seems to be traceable to defective ventilation rather than to the real necessities of the case. Air is supplied through a small pipe, and is drawn from a place where the temperature is 95° Fahrenheit. Under such circumstances it is not surprising to read that in this hot mine the air is hotter than the rock, a state of things which I have never observed in the Comstock. Other mines have been reported to the British Coal Committee as having temperatures of 106° Fahrenheit and thereabouts, but the only positive comparisons that are available at this writing are the following, all from Cornish mines * Read by permission of Lieut. Geo. M. Wheeler, Corps of Enginerrs, U. S. Arm J, in charge of U. S. Geographical and Geological Surveys, west of the 100th meridian.

Jan 1, 1879

By AIME AIME

APPARENTLY unperturbed by any misgiving as to ill luck connected with the mystic number thirteen -for there were exactly that number of Directors on deck-the Board held two sessions on Tuesday, Feb. 21. , . Between the executive session at 5:15 p. m. and the general session at 8:30 p. m., 28 Section and Division delegates were wests of the Directors at dinner. Committee chair- " men and past officers brought the attendance to 75. Messrs. McAuliffe, Merica, Mudd and Tally had expressed their intention to be at the Directors' meeting, but each was prevented unavoidably at the last minute. At the executive session of the Board, J. V. W. Reynders was unanimously chosen to fill the unexpired term of Dr. Becket as Director: and Eugene McAuliffe in like " manner was selected to become Vice-president to fill the vacancy created hy Dr. Becket's assumption of the Presidency. Upon nomination of President Becket the following Executive Committee was appointed: Frederick M. Becket, chairman; Howard N. Eavenson, H. A. Guess, J. V. W. Reynders and William Wraith; and the Finance Committee was appointed as follows: Henry Krumb, chairman; Paul D. Merica and H. G. Moulton. Karl Eilers was reelected Treasurer and A. B. Parsons was re- elected Secretary to serve for the ensuing year, whereupon the executive session was adjourned.

Jan 1, 1933

By M. C. Flemings, G. E. Nereo

General expressions are given to describe macro-segregation in castings and ingots which results from mass flow of solute-rich liquid to feed solidification and thermal contractions. Analytical solutions are given for solidification with planar isotherms (unidirectional and bidirectional heat flow). These solutions describe inverse segregation and centerline segregation. Numerical examples are given for A1-4.5 pct Cu alloy. In 1540, Vannoccio Biringuccio published one of the first references to macrosegregation, describing the problem of exudation and inverse segregation in the manufacture of bronze gun barrels.' Since then, a great many studies of macrosegregation have been reported. Recent work of particular engineering interest includes that of Marburg 2 and others:" on centerline segregation and other types of segregation in large steel ingots, and work of Adams,5 Scheil, 6 and Kirkaldy and youdelis7 on inverse segregation in nonferrous ingots. In most studies on this subject, the various types of macrosegregation have been treated as separate phenomena. For example, quite different mechanisms have been proposed for formation of centerline segregation, negative cone of segregation, inverse segregation, banding, and so forth. In this, and in several papers to follow, it is proposed that these as well as other types of macrosegregation result from the same basic mechanism and can be quantitatively described by the same basic equation. It has often been suggested that some types of segregation (such as centerline segregation and banding) occur as a result of buildup of solute at the tips of growing dendrites.2-4 ,8-10 As example, banding can be induced in centrifugal castings by mechanical vibration, and Northcott 10 suggests this might be due to the influence of the vibration on the boundary layer at the dendrite tips of the growing dendrites. However, in view of the extremely small boundary layer known to exist at the tips of the dendrites,11,12 any interpretation of macrosegregation based on this boundary layer is clearly incorrect. Note that experiment has shown that significant buildup of solute does not occur at dendrite tips in ingot solidification, but even if such buildup occurred the thickness of the enriched zone would only be the order of D/U where D is liquid diffusion coefficient and U is dendrite tip velocity. For usual casting or ingot solidification this solute-enriched layer is 10"3 cm, far too small to account, for example, for centerline segregation.11'12 It has also been suggested that convection in the bulk liquid (ahead of the advancing dendrites) might cause segregation by sweeping away the solute-rich boundary layer in front of the dendrites.3 However, since there is no significant boundary layer, this explanation must be incorrect. The convection might directly cause segregation by penetrating between the dendrite arms, and presumably in a rimming steel ingot it is sufficiently vigorous to cause some segregation in this way. Centerline segregation, however, cannot be interpreted as resulting from this convection since a sharply segregated zone is usually found near the centerline, with the bulk of the ingot being nearly of nominal composition. If convection in the bulk liquid were the direct cause, a gradual change in ingot composition over the entire cross section would be expected. It is known that sudden changes in convection of the bulk liquid during solidification can result in banding,14 but it is not clear that the banding results directly from the effect of convection on solute distribution. Changes in convection also affect thermal conditions in the liquid-solid region of a solidifying ingot. It will be seen later in this paper, and in a paper to follow, that macrosegregation is strongly influenced by these thermal changes. Recognizing that in some cases of ingot solidification (as in solidification of rimming steels) convection in the bulk liquid may have a direct effect on solute distribution, we neglect it in this paper and in the several to follow. We then derive general expressions describing macrosegregation which results from the mechanism of interdendritic flow of solute-rich liquid

Jan 1, 1968

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

The results of a preliminary study of 113 ternary titanium-base alloys are described. The compositions investigated were as follows: 1. Ternary titanium-carbon alloys containing copper, silicon, vanadium, chromium, manganese, iron, or cobalt. 2. Ternary titanium-nitrogen alloys containing chromium. 3. Ternary titanium-chromium alloys containing additions of vanadium, molybdenum, tungsten, cobalt, or nickel. 4. Ternary titanium-manganese alloys containing additions of silicon, chromium, tungsten, or iron. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships for these alloys were determined. THIS is the second in a series of papers describing some of the results of the exploratory work on titanium alloys being conducted at Battelle Memorial Institute for the Wright-Patterson Air Force Base. The work with the binary alloy systems has been described in a previous publication.' This paper describes ternary titanium-base alloys as follows: 1. Ternary titanium-carbon alloys containing copper, silicon, vanadium, chromium, manganese, iron, or cobalt. 2. Ternary titanium-nitrogen alloys containing chromium. 3. Ternary titanium-chromium alloys containing additions of vanadium, molybdenum, tungsten, cobalt, or nickel. 4. Ternary titanium-manganese alloys containing additions of silicon, chromium, tungsten, or iron. As the preparation and fabrication of the 0.5-Ib experimental titanium alloy ingots to 14-ga sheet, as well as the methods of testing used in this work, have been described in the first paper of this series, Titanium Binary Alloys, no further discussion of these techniques will be given. Ternary Alloys Containing Carbon The following alloys of titanium, containing carbon and one other metal, were investigated: 1. 0.25 pct carbon; 1, 2.5, and 5 pct copper. 2. 0.25 pct carbon; 1, 2, and 3 pct silicon. 3. 0.25 pct carbon; 1, 2.5, and 5 pct vanadium. 4. 0.25 pct carbon; 2.5, 3.5, 5, 10, and 15 pct chromium. 5. 0.5 pct carbon; 2.5, 3.5, and 5 pct chromium. 6. 0.25 pct carbon; 1, 1.75, 2.5, 3.5, 5, 7.5, and 10 pct manganese. 7. 0.5 pct carbon; 1.75, 2.5, 3.5, 5, 7.5, and 10 pct manganese. 8. 0.25 pct carbon; 0.25, 0.5, 1, and 2 pct iron. 9. 0.25 pct carbon; 1, 2, and 3 pct cobalt.

Jan 1, 1951

By S. F. Reiter

The paper presents isothermal recrystallization curves for 0.08 and 0.15 pct C steel at subcritical temperatures following small amounts of plastic deformation. The effects of deformation, temperature, and aging on nucleation and growth rates ore described. The free energy of activation for grain boundary migration in steel is given. SEVERAL excellent reviews of the literature have appeared concerning the recrystallization of metals.'-' The present investigation follows the approach advanced by Mehl, Stanley, and Anderson,6-7 in which the rate of recrystallization was analyzed in terms of N, the rate of nucleation, and G, the rate of growth of recrystallization nuclei. Two lots of low carbon, capped steel of the analysis given in Table I were studied. Each lot consisted of a 150 lb coil which had been hot rolled to 0.083 in. and then cold rolled to 0.042 in. at the mill. Strips 0.930 in. wide were sheared perpendicular to the rolling direction. Both steels were normalized before studying their recrystallization characteristics. The strips were cleaned, painted with a magnesia-acetone paste, and made into packs of equal weight, wrapped in 0.002 in. copper foil. The packs were placed in a salt bath at 900°C for 30 min and air cooled. A relief anneal followed in a second salt bath for 15 min at 650°C. The relief anneal was found necessary from early tests in which a longer incubation period and slower rate of recrystallization were observed in relief-annealed lot A steel than in similar material which was strained and recrystallized directly after being normalized. This effect, which indicates the presence of transformation and/or cooling stresses in steel air cooled from above the A, temperature, has also been observed by Samuels8 and Masing.9 Figs. 1 and 2 show the microstructure of lot A and B materials and illustrate the rather uniform No. 8 ASTM grain size produced by this heat treatment. Winlock and Leiter10 observed that strip specimens which had their sharp edges removed elongated more uniformly than those which were not polished. Similarly, when the sheared edges were removed on a belt grinder, it was found in the present investigation that such samples recrystallized more uniformly than did unpolished strips. Therefore, all strips were carefully rounded prior to their extension. The approximate strain limits for the production of large recrystallized grains are from 6 to 12 pct extension." It was found that for the purpose of this investigation, 8 and 9 pct elongation were suitable deformations. The strain rate employed was 0.01 in. per in. per min and produced a yield point elongation of 4 pct. Winlock and Leiter found that mild steel of No. 8 ASTM grain size gave the same yield point elongation when extended at 0.012 in. per in. per min. All of the lot A and B strips extended in tension developed a straight, stretcher strain line at each grip when the upper yield point was reached. The lines were parallel and made an angle of 55" with the edge of the strip. They approached each other with increasing strain and met near the center of the sample at the end of the yield point elongation. Immediately thereafter, a small drop in load was observed and then the load increased in a regular manner with increasing extension. The grips were initially 8 in. apart. After extension, the 6 in. gage length was carefully cut into 1 in. samples. The remainder of the strip was discarded. After a flash pickle in hot 50-50 hydrochloric acid, six samples, each of which had been taken from a different strip, were placed in a basket and submerged in a lead pot for isothermal recrystallization. Although no recovery effect was observed, strain aging did occur after extension. Therefore, samples were always recrystallized within 24 hr after their cold deformation. After recrystallization, the samples were etched with a solution comprised of one part by volume of nitric acid with three parts of water. Bromide printing paper was exposed directly at low magnifications and later used with a mask to measure the desired quantities. First, the average diameter of the largest grain visible in each sample was determined using dividers. Next, the number of recrystallized grains per unit area was counted and recorded as n. Then, for each sample, the combined area of the recrystallized grains was measured by transcribing the grain outlines to standard graph paper. Many determinations of the area of the recrystallized grains were repeated five times and indicated a standard error that was not greater than 25 pct. The average area for six samples was divided by the area of the mask to yield the percentage recrystallized. Recrystallization of 0.08 Pct C Steel The progress of recrystallization at 670°C after 8 pct elongation of lot A steel is shown in Fig. 3, a through f. The shapes of the growing crystals are approximately equiaxed, as is assumed in the

Jan 1, 1953

By David W. Pasho

The success of a collector vehicle, designed to recover manganese nodules under the conditions which exist in deep ocean mine sites will in part be determined by the effectiveness of pick-up and running gear mechanisms. For the purpose of qualitative comparison, some specific aspects of seafloor interactions with various concepts are reviewed utilizing existing data on seafloor characteristics and running gear/tool interaction with soils.

Jan 1, 1976

By D. M. Given

HOW much can the mine operator afford to spend on his coal burning boiler plant? The usual answer is as little as possible and still get the job done. Thus, attention must be focused on the spot where excessive costs are most likely to arise - the materials handling end of the job. Boiler plants consuming less than 30,000 tons of coal annually can be controlled to the point where costs for handling coal and ashes are under $1.00 per ton. There is a wide selection of coal and ash-handling systems that can be used in smaller boiler plants to provide labor savings and convenience required if management is to accept coal as fuel.

Jan 7, 1953

By William Fink

SINCE so many different curves have been published for the solid solubility of zinc in aluminum, it seems desirable to definitely establish the correct curve by two or more independent methods. The curve published in part I1 was based entirely upon X-ray measurements because the other methods employed at that time were not satisfactory. The present paper (the seventeenth of this series on high-purity aluminum alloys) describes the determination of the solid solubility of zinc in aluminum by the measurement of electrical resistivity at temperature and by microscopic examination. Since the publication of our part I in 1932, an investigation of the solubility relations in the aluminum-zinc system has been reported by Schmid and Wassermann2, who obtained their solubility results from lattice-parameter measurements on heat-treated and quenched speci-mens. The diagram that they published is shown in Fig. 1. In this investigation they also found by X-ray measurements that the parameter of the gamma phase changed continuously with zinc content and at such a rate that it would be identical with that of the beta phase at 60 atomic per cent zinc. It was concluded therefore that the beta and gamma phases, from the point of view of structural relationship, are one single phase. They also suggested a gap of immiscibility between 270° and 350° C. The complete boundary in this region could not be deter-mined satisfactorily by the method employed and therefore was not shown in their diagram.

Jan 1, 1936