Search Documents

By M. Paulus

It is known that multicomponent powders are mostly nonhomogeneous. This paper investigates the effects of nonhomogeneity of composition and grain size on the melting point and the sinterability of compact taking into account homogenization mass transport and the length of the diffusion path in solid state sintering, and the kinetics of liquid phase formation in liquid phase sintering. After a discussion on the ideal characteristics of a powder for sintering and low temperature reaction, the main conventional processes are compared. Finally we develop the freeze-drying technique and demonstrate the capabilities and the limits of the process by some examples, mainly in the ceramics field.

Jan 1, 1980

By David W. James, Howard Jones, George M. Leak

Conditions are described for producing, by primary recrystallization, a matrix suitable for the growth of large grains near (110)[001] orientation in silicon iron strip by secondary recrystallizaliun in a steep temperature gradient. The orientation distribution of these large grains is expressed in terms of rotational deviations about the cross-rolling direction, the rolling direction, and the normal to the sheet, the deviational spread increasing in that order. With the aid of cowplenientary published data on the orientation dependence of growth rate, it is shown that this observation is consistent with the oriented-growth theory of recrystallization lextures. It is conclutled that growth-rate and orientation-distribution data obtained in a steep thermal gradient should be used with caution to account for isothermally Produced recrystallization textures. SEVERAL authors have reported methods of growing large grains by re crystallization of a small-grained matrix in silicon iron 1- B and pure a cr The present study was a preliminary in the growth of single crystals and bicrystals for surface relaxation," grain boundary mobility, and grain boundary diffusion studies. The method was to control the growth of a seed crystal into a suitable primary re crystallized matrix by feeding through a steep temperature gradient. The driving energy for growth derived from the grain boundary energy released as the seed crystals grew into the matrix. Thus, stability of the matrix against normal grain growth was considered to be essential for success. It was known that the manganese sulfide dispersion present in commercial silicon iron performs this function during secondary recrystallization to the (110)[001.] texture.12 Hence commercial, rather than high-purity, material was used throughout. The paper describes the growth conditions for grains large enough to be used as seed crystals for further growth into single crystals. The orientation distribution of the seed crystals is analyzed and its significance for the theory of recrystallization textures is discussed. EXPERIMENTAL PROCEDURE Strip material was supplied by the Steel Co. of Wales, Ltd. The chemical analysis in weight percent was Si, 2.90; C, 0.015; Mn, 0.059; P, 0.011; S, 0.027; Ni, 0.032; 0, 0.009; Fe, balance. A gradient furnace of similar design to one described previously4 was loaned from B.I.S.R.A. It consisted essentially of a vertical water-cooled copper slot projecting downwards into the hot zone of a molybdenum furnace. Hydrogen was passed through the furnace to protect both heating element and specimen from oxidation. Strip specimens up to 8 cm wide and 0.2 cm thick were sealed into the furnace at the mouth of the copper slot. A coating of light oil on the strip surface maintained the seal during translation of a specimen. The maximum temperature gradient in the region just below the copper slot was 500°C per cm over 1 cm, with the hottest point controlled at 1175°C. Several large grains would usually grow by secondary recrystallization from the primary matrix when a specimen was immersed in the hot zone for about 30 min. A back-reflection X-ray camera was constructed to facilitate rapid and accurate orientation determinations of the large grains produced. It was possible to reproduce a standard geometry, with regard to strip and camera, without the tedium of careful alignment on each occasion. Specimens, typically 4 cm wide and 75 cm long, were cut with the longitudinal axis parallel to the rolling direction of the original strip. The surfaces were cleaned by immersion alternately in a hot aqueous solution containing 2 pct hydrofluoric acid plus 10 pct sulfuric acid and in cold 10 pct nitric acid. The nitric acid etch was just sufficient to reveal the grain structure. Rolling and annealing treatments to prepare the matrix (discussed below) were followed by growth of seed crystals in the gradient furnace. The matrix was transformed to a single crystal by growth of a selected seed crystal connected to the matrix by a thin neck. 4,5 Growth was promoted by controlled feeding into the gradient furnace. Several single crystals of controlled orientation were grown successfully from seed crystals by twisting the interconnecting neck in a reorien-tation jig.4 EXPERIMENTAL RESULTS AND DISCUSSION Growth Conditions. A suitable matrix for growth of large grains was prepared starting from primary re-crystallized strip 1.9 mm thick. This was cold-rolled in two stages each being followed by a recrystallization anneal at 800°C for a few minutes. Such treatment gave the required growth matrix only if the two cold-reduction stages were each performed in several passes and in the following ranges: the first, 30 to 70 pct; the second, 10 to 50 pct. Immersion in the temperature gradient otherwise resulted in an equiaxed

Jan 1, 1967

By B. B. A. Luzzat

ALUMINUM is today the most widely used of the nonferrous metals. The technical literature on the aluminum smelting process is, nevertheless, very meager, so that anyone interested in the subject cannot rely on more than a couple of dozen publications.' The patent literature is equally scarce; most patents refer to the production of alumina from aluminum-bearing ores, while not more than a few score significant patents deal with the electrolytic reduction of alumina, which is the real core of the aluminum smelting industry. The "reduction phase" is, from a technical and a scientific point of view, much more interesting than the "alumina phase", which, in effect, is only a combination of such well-known chemical operations as dissolving, precipitating, filtering, drying, and calcining. The electrolytic reduction of alumina, on the other hand, has features which do not appear in any other metal smelting operation. Some of them are of great technical and scientific interest even for those not directly engaged in the production of aluminum. The purpose of this paper is to describe in some detail the basic facts and developments of the reduction phase of aluminum smelting. Two Aspects of the Electrolytic Process The raw material for the reduction process is alumina (Al2O3) . Its purity in general runs as high as 99.50 pct or more. Small differences in the chemical composition generally do not affect the reduction process.* Of more importance are the physical prop- erties of the alumina, since they affect not only its rate of solution in the molten bath but also its heat insulating power.† In the following pages, un- less otherwise stated, it is assumed that a standard "Bayer" alumina is used. The reduction process, by which alumina is broken down into its components, may be roughly defined as its electrolysis in molten cryolite. The oxygen separates at the anode, and the aluminum at the cathode, which forms the bottom of the electrolytic cell. The electrolytic cell (or pot) where the process is carried out is a strongly reinforced steel box. The

Jan 1, 1951

By Jacques Friedel

Jan 1, 1964

By R. H. B. Jones

THIS paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recognizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and development. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation.

Jan 1, 1946

By A. V. Henry

THE kaolins of the southeastern United States were known to civiliza-tion as early as the latter part of the eighteenth century-and yet the Fig. 1.-KAOLIN PRODUCTION AND IMPORTS. commercial history of Georgia kaolins may be said to begin in the year 1900. The U. S. Bureau of Mines reported for that year a production of 6885 tons of "miscellaneous" clays in Georgia. A comparison of these figures with those of 1934, when the production rose to 284,556 tons (65 per cent of the domestic production), indicates the growing economic and technologic importance of this raw material. Fig. 1 clearly shows that a part of the increase is due to a normal growth in the use of kaolinitic clays and a part is due to replacement of clays formerly imported.

Jan 1, 1937

By C. H. Curtis

The Esperanza mine of the Copper Division of Duval Sulphur & Potash Co. is located in the Twin Buttes District, 32 miles southwest of Tucson, Ariz. Records of mining activity in this vicinity date back to the 1850's. The New Year's Eve mine, which was last active briefly during the years of World War II, made the first actual penetration into what is now Duval's Esperanza property. Duval's exploration department became interested in the Esperanza in the fall of 1954. The first test hole was started on May 8, 1955. Two years of intensive exploration work together with metallurgical studies developed the basis for the decision to establish an operation.

Jan 11, 1961

By C. H. Mathewson

THIS paper was prepared upon request as a contribution to a symposium covering the manufacture, properties, and uses of the important non-ferrous metals. In approaching a subject as broad as this, there is a natural desire to build up a comprehensive and finished production which shall constitute a dependable source of information on all questions properly belonging to this branch of metal technology. There are, however, a number of circumstances, apart from the mere routine of labor and thought involved, which operate rather effectively against the possibility of completing such an ambitious program at the present time. First of all, as far as any public record of results is concerned, the commercial rolling, drawing, and forming of zinc with relation to changes of structure and properties-and this we consider to constitute the elements of metal technology-might as well be an unpractised art. We have never seen a published photomicrograph showing the structural characteristics of either hard or soft sheet or strip, although the structure of castings has been frequently described, and other coarse-grained structures resulting from hard-hammering and annealing have been reproduced. Thus, an author in this field must proceed to his task without much assistance from the literature, and the outcome can represent only a personal estimate of principles, facts, or findings, and not a summary

Jan 9, 1919

By Albert Sauveur

The following propositions and corollaries are intended to present, as concisely as possible, some of the evidences gathered while studying the microstructure of steel. Each proposition is accompanied by photo-micrographs showing the structure of illustrative samples. But it must be understood that the special instances thus chosen for illustration are by no means the only ones on the examination of which the propositions are based. On the contrary, they have been taken almost at random among a great many, in some instances more than a hundred, similar cases. Proposition I. A slow and undisturbed cooling from a temperature x or higher produces crystallization. Plate L, Plate II., Fig. 1, and Plate V., Figs. 1, 2, 3 and 4 show the crystalline structure of several pieces of steel. Plate I. reveals this structure in the center of a slowly-cooled Bessemer ingot, 1.5 feet from the top. Plate II., Pig. 1, is from a small 2-in, square testingot of the same heat, slowly cooled. Plate V., Figs. 1, 2, 3 and 4 show the structure of different parts of steel rails. The original photographs were all magnified 70 diameters, and have been reduced in engraving to 63, or to 55 diameters, as shown in the plates. Proposition 11. Undisturbed cooling from an initial temperature lower than x is not accompanied by crystallization. Plate III., Fig. 5, shows the structure of a piece of rail-steel forged from a white heat until it had fallen to dull-red. The structure is almost amorphous. Practically no crystallization has taken place during the subsequent cooling. Corollary.—Pieces of steel finished at a temperature lower than x do not take a crystalline structure.

Jan 1, 1894

By P. Beardmore, B. W. Howlett, B. D. Lichter, M. B. Bever

The heats of formation at 273°K of the compounds Mg2Ge, Mg2sn, and Mg2b, the heats of fusion and melting points of Mg2Sn and Mg2Pb, and the heats of solution of magnesium, germanium, and lead in liquid tin have been measured. The excess free energies of the liquid alloys and the free energies of formation of magnesium-Group IVB compounds at their melting points and their standard free energies of formation at 298°K have been calculated. The stability and bonding of the compounds are discussed with reference to these properties. Some thermodynatnic aspects of the liquid phases in the systems Mg-Sn and Mg-Pb are also considered. THE compounds of magnesium with the Group TVB elements, silicon, germanium, tin, and lead, have often been considered to constitute a nearly ideal homologous series. In particular, their thermodynamic stability has been assumed to decrease with increasing atomic number of the Group IVB element.' The binary-phase diagrams of the magnesium-Group IVB elements given by Hansen and Anderko2 have the same form. Each system has a single con-gruently melting compound of limited homogeneity range. The structures of these compounds, which have the formula Mg2X, are anti-isomorphous with the calcium fluoride structure. A recent investigation has found evidence of a second compound in the system Mg-Pb.3 The solid compounds Mg2Si, Mg2Ge, and Mg,Sn are semiconductors, while the conductivity of Mg2Pb approaches that of a metallic conductor. This difference suggests that other properties may also show a discontinuity. The investigation reported here is concerned with the thermodynamic properties of magnesium-IVB compounds and particularly their variations with the period of the Group IVB element. The heats of formation at 273°K of the compounds MgzGe, Mg2Sn, and Mg2Pb and the heats of fusion and melting points of Mg2Sn and Mg2Pb have been measured. The results, combined with published data, are interpreted in relation to the stability and the bonding characteristics of the compounds. Some thermodynamic aspects of the liquid phases in the systems Mg-Sn and Mg-Pb are also considered. In the course of the investigation the heats of solution of magnesium, germanium, and lead in liquid tin have been determined. 1) EXPERIMENTAL PROCEDURES 1.1) Samples. Samples of the compounds Mg2Ge, Mg2Sn, and Mg2Pb, supplied by Professor P. Aigrain, Compagnie Générale de Télégraphie Sans Fils, were used in measuring heats of formation, heats of fusion, and melting points. Samples of Mg2Sn and Mg2Pb, supplied by Dr. V. B. Kurfman, Dow Metal Products Co., samples of Mg2Sn, prepared at the Air Force Cambridge Research Laboratories, and samples of MgzPb, prepared in this laboratory, were used for additional measurements of the heats of fusion and the melting points. The samples were stored in evacuated Pyrex capsules or under nonreacting liquids. 1.2) Heats of Formation. The heats of formation at 273°Kof the compounds Mg2Ge, Mg2Sn, and Mg,Pb were measured by tin-solution calorimetry. In this method, samples of the compound and of a mixture of the constituent elements are added alternately from 0°C to a tin-rich bath. The difference between the heat effects, corrected for the change in composition of the bath, is the heat of formation of the compound. Details of the method have been given elsewhere. 4 The bath was maintained at 350°C for the dissolution of the compounds MgzSn and Mg2Pb. Since at this temperature the dissolution of Mg2Ge was too slow, a bath temperature of 400" or 450°C was used with this compound. At least three calorimetric runs, each of approximately six additions, were made with each compound. 1.3) Heats of Solution. The determination of the heats of solution of magnesium, germanium, and lead in tin was included in this investigation because they were not well-established at the time this work was started. To obtain the heat of solution, the difference

Jan 1, 1967

By T. S. Lundy, F. R. Winslow

DIFFUSION coefficients of Hf181 in the high-tem-perature bcc phase of reactor-grade hafnium were determined at temperatures of 1795° to 1995°C by standard lathe-sectioning techniques. The temperature dependence of the data may be described by an Arrhenius-type expression for this limited temperature interval. However, hafnium is classed with the "anomalous" bcc metals zirconium, titanium, and y uranium by the low values of Do and Q observed in this study. The hafnium metal was received as 1/2-in.-diameter crystal bar. Analyses by the Analytical Chemistry Division of Oak Ridge National Laboratory showed the major impurity to be zirconium— about 2.1 pct. The total interstitial content was about 225 ppm with 190 ppm of this oxygen. The Hf"' was supplied as HfC12 in HC1 solution by the Isotopes Division of Oak Ridge National Laboratory. The hafnium bar was cut into disk-shaped specimens 3/8 in. long. One of the flat faces of each specimen was metallographically treated and then the isotope was deposited by vacuum evaporation from a tungsten filament. A 3 by 3 in. NaI (Tl) crystal with a single-channel analyzer was used for counting y rays with energies of 0.3 to 0.7 Mev. The as-deposited layers of isotope had counting rates of about 200 counts per sec. Specimens were annealed in argon in a tantalum resistance furnace. Temperatures were measured with a microoptical pyrometer calibrated for the particular furnace sighting conditions. All sectioning was done by standard lathe techniques. Section weights were determined on a semimicrobalance. A density of 12.5 g per cu cm was used in determinations of section thicknesses. Activities associated with the various sections were measured and the penetration data were treated using the computer code by winslow.' In all cases, except for specimens annealed at temperatures below 1795°C, normal Gaussian penetration behavior resulted. At lower temperatures, plots of In A(x) vs x2 were nonlinear [~(x) = relative activity at a distance x from the

Jan 1, 1965

By A. T. Shurick

THE present economic crisis in bituminous coal is substantially the most insidious, and critical, in the modern history of the industry. The large consumption deficit that has gradually developed (almost unawares), has culminated in a situation that has forced home the urgent necessity for prompt and radical remedial measures, such as the various mergers now in course of negotiation. Conditions today are sufficiently comparable with those in the iron and steel industry, preceding the formation of the United States Steel Corpn., to suggest the possibility of a sweeping super-consolidation, that all but staggers the imagination. The important function of the banker in this, and lesser projects, is too well known to require comment, and it is important that we understand clearly just what these functions are. Certain features in banking practice came up for consideration in connection with a rather exhaustive economic study into the prospective future of the coal industry, upon which I was recently engaged for an Eastern bituminous interest. This survey was made for the purpose of effecting a decision on certain pressing questions of policy, involving considerable capital expenditures, that would be compatible with the flattening out in the curve of production in recent years. An examination of the TRANSACTIONS, and the coal literature generally, failed to disclose any pertinent, and authoritative data, on this subject. This was more or less characteristic of the whole survey, which had involved a large amount of original research, and measures were taken to procure the required information. The following notes have been compiled largely from the data thus collected, supplemented with material, suggestions and criticisms, by several of the larger banking houses active in coal, together with personal memoranda of my own.

Jan 1, 1928

By H. D. Williams, R. A. Scriven

The distribution of elevation angle of finite plane facets distributed symmetrically about a given axis is derived in terms of the angular distribution of lines which these facets produce in a plane section parallel to the axis. It is assumed that the facets are not markedly elongated in preferential directions. The theory is intended for application to the angular distribution in polycrystalline metals of slip planes and of particular grain boundaries on which certain phenomena such as cavitation can occuv. Illustrative examples are given in closed form and simple numerical techniques are de-ueloped for practical application. The results are applied to the distribution of cavitated boundaries in a copper specimen after fatigue at 400°C and it is found that voids form on the boundaries that exper~enced maximum shear stress. When investigating the distribution of elevation angle between a given axis and planes symmetrically distributed about this axis the angular distribution observed in a plane section parallel to the axis is not necessarily the same as the required distribution. Consequently a technique for processing the results obtained by sectioning methods is required. An example where such a technique would find application is in the problem of intercrystalline void formation during uniaxial tensile creep. Two theories have been proposed to explain this cavitation in terms of the normal and the shear components of stress, respectively. Hull and Rimmer (1959) postulate that the growth of intercrystalline voids is controlled by the rate of supply of vacancies from the grain boundary, the local vacancy concentration being proportional to the normal stress on the boundary. Gifkins (1956) considers that slip arising within a grain causes a ledge to be formed at the grain boundary which is subsequently opened up into a cavity by grain boundary sliding. It might be possible to differentiate between these mechanisms by determining the angular distribution of grain boundaries containing cavities since the former theory predicts a predominance of cavitated facets normal to the stress direction whereas the latter should favor an angle of 45 deg to this direction. In a similar manner an indication may be obtained of the type of mechanism responsible for intercrystalline cavitation during high-temperature fatigue. Davies and Wilshire (1962) have analyzed the slip-plane distribution in a nickel specimen but the problem was not treated in any detail nor was any account taken of the finite extent of the planes being sectioned. Hilliard (1962) has given a very general account of how anisotropy in the microstruciure can be related to measurements taken in one or more plane sections by expressing both the measured and the true angular distributions as expansions in spherical harmonics.* The present analysis is con-

Jan 1, 1965

By I. Nilsson, G. Sundkvist, A. Danielsson

A spectrochemical method of slag analysis is descibed which utilizes fusion of the sample with a flux, then cooling and crushing to put all samples into a common form. The powder, is then fed onto adhesive tape and passed through a spark by means of a special device to provide very reproducible discharge conditions. Combined with a direct-reading optical emission instrument, this system provides speed and accuracy of antilysis heretofore unobtainable for. slag samples by any other method. THERE are many suggested methods for spectro-chemical analysis of slags. The most important are fusion-pellet methods and solution methods. In our company the fusion-pellet method has been used earlier, and is described by Lounamaa. W. H. Tingle and C. K. Matocha have made refinements of the pellet method.' A Committee of the British Iron and Steel Research Association has investigated different methods of spectrochemical analysis of slags. Its purpose was to formulate a method which would give the complete analysis in 30 min with an accuracy of ±3 pct. The committee recommends a solution technique, which was thought to correspond best to their requirements. The method to be described is a fusion-tape method. The sample is isoformed by fusion and grinding. The powder is analyzed with the tape technique. The tape machine and some of its applications are described earlier.4'5 The powder to be analyzed is continuously fed onto a moving adhesive tape, which passes through the spark gap. The sparks break through the tape and vaporize and excite the material to be analyzed. The most outstanding feature of the tape machine is its very high reproducibility. The concept of isoformation has been introduced earlier.= It means a pretreatment of the samples to make them uniform from the spectralanalytical point of view, i.e., cancelling systematic differences between the samples. The purpose of the isoformation is to reduce the influence of particle size, as well as chemical and mineral composition. Before describing the isoformation by fusion plus grinding, which is the purpose of this paper, a few words will be said about two other types of isoformations, i.e., grinding with buffer and ion exchange plus grinding as they have been considered during the application of the tape technique for slag analysis. Grinding with buffer might be a sufficient isoformation in some special cases, where the mineral composition is defined. The time of grinding must, however, be rather long, at least 5 to 10 min, even when using such an efficient mill as the Swing Mill from Messrs. Siebtechnik, Mühlheim, Germany. This type of isoformation is not recommended due to its limitations and due to the fact that the gain in time compared with the fusion technique is almost negligible. The principle of ion exchange plus grinding and some of its applications have been described.5 The following elements of interest in slag analysis can be determined in this way: Na, K, Cu, Mg, Ca, Ba, Zn, Pb, Al, Cr, Mn, Fe, Co, Ni. The very important element Si, however, cannot be analyzed with this method. Although the ion exchange isoformation for slag analysis cannot be looked upon as a routine method, it can be used for

Jan 1, 1962

By H. M. Ziesemer, George Mieyr

Prior to 1909 that mountain of porphyry known as Sacramento Hill had hardly been touched though it had always been thought to contain ore. During that year, exploratory work was started by underground methods; drifting and raising continued until 1913. It was proved that a mineralized zone existed, the limits of which had not been determined ; so, because of the lower costs of exploratory work and the greater desirability of vertical sections, it was decided to prove the extent of the ore zone by churn drills. Drilling continued until 1917, when it seemed almost certain that the horizontal limits of the orebodies had been determined. Ore continued in depth in one direction beyond a point where it was economical to explore by churn drilling; this extension is still being developed by underground methods. The irregularities of the boundaries of the ore zones, together with the variable grades of ore encountered, made it necessary to drill on the corners of 100-ft. squares. Two ore zones were proved, known as the East and West Orebodies. The Sacramento Hill porphyry stock intruded into the Dividend fault. The fault ran roughly east and west with a dip to the south, having pre-Cambrian schists on the north against Paleozoic limestone on the south. This intrusion was accompanied by a silica breccia on the south periphery, along the limestone contact side. The ore lay in the silica breccia and in the porphyry, some distance from the breccia. NO ore was found in the heart of the porphyry mass on the north side, along the schist contact. The West Orebody is elliptic in shape, having a major axis of 1200 ft. (366 m.) and a minor axis of 800 ft. (244 m.); these diminish with depth until, at 300 ft., the axes are 500 ft. and 300 ft., respectively. The ore consists of chalcocite, some bornite, chalcopyrite, and considerable pyrite in a siliceous gangue. About 30 per cent. of the copper is caused by

Jan 1, 1923

By James O. Lewis

Gravity drainage is the self-propulsion of oil downward in the reservoir rock. Under favorable natural and operational conditions, it has been found to effect recoveries comparable to water displacement. With modern technical knowledge, the operator can often make a choice between dissolved gas drive, water drive and gravity drainage as the principal recovery agent in a reservoir. It is desirable that the opeator be able to determine which of the three agents will be most effective under each set of conditions. So far, gravity drainage has received less consideration than the other two. In this paper. an endeavor is made to set forth some of the principles of gravity drainage, to point out the types of reservoirs favorable for it, and to show how it may be applied in them. Field examples are described and discussed. Introduction Since early in the history of the oil industry, it has been recognized that gravity is one of the three important natural forces for expelling oil from the reservoir rock. As knowledge of the technology of oil recovery progressed, ideas changed with respect to the relative importance of the three forces and with respect to the manners in which they functioned. For a time, disproportionate emphasis was placed on the importance and function of gas and the need for conserving gas pressures. More recently, disproportionate emphasis has been placed on encroaching edge water. Only lately has there been evidence that the function and importance of gravity was to receive due consideration. Study of this neglected phase of oil recovery is needed to round out our knowledge of reservoir behaviors and to gain a balanced viewpoint of the interplay of forces that may operate in varying importance in reservoirs. The purpose of this paper is to discuss mainly in a qualitative way, the functions of gravity, to present some concrete instances where it has been important and to raise some questions that should be investigated further. Oil-recovery Agents The important natural agents for effecting oil recovery that may be originally available in a reservoir are gas, both dissolved in the oil and free in gas caps, encroaching edge water and gravity. Each of these agents can act in a dual capacity—physically to overcome the surface energies that hold the oil within the pores and mechanically to overcome viscous . resistance and to propel the oil through the porous reservoir rock to the wells. Advancing edge water displaces the oil from the pores and lifts it updip to structurally lower wells. Gravity drains the oil from the pores and flows it downdip to the wells. Gas displaces oil from the pores, entrains it in the gas stream and flows it to the wells, but gas in solution also affects the physical properties of the oil and thus can influence oil recovery by the other agents, whether or not the mechanical energy in the gas is utilized. Of the two functions of these agents, the more important is the ability to dis-

Jan 1, 1944

By James O. Lewis

Gravity drainage is the self-propulsion of oil downward in the reservoir rock. Under favorable natural and operational conditions, it has been found to effect recoveries comparable to water displacement. With modern technical knowledge, the operator can often make a choice between dissolved gas drive, water drive and gravity drainage as the principal recovery agent in a reservoir. It is desirable that the opeator be able to determine which of the three agents will be most effective under each set of conditions. So far, gravity drainage has received less consideration than the other two. In this paper. an endeavor is made to set forth some of the principles of gravity drainage, to point out the types of reservoirs favorable for it, and to show how it may be applied in them. Field examples are described and discussed. Introduction Since early in the history of the oil industry, it has been recognized that gravity is one of the three important natural forces for expelling oil from the reservoir rock. As knowledge of the technology of oil recovery progressed, ideas changed with respect to the relative importance of the three forces and with respect to the manners in which they functioned. For a time, disproportionate emphasis was placed on the importance and function of gas and the need for conserving gas pressures. More recently, disproportionate emphasis has been placed on encroaching edge water. Only lately has there been evidence that the function and importance of gravity was to receive due consideration. Study of this neglected phase of oil recovery is needed to round out our knowledge of reservoir behaviors and to gain a balanced viewpoint of the interplay of forces that may operate in varying importance in reservoirs. The purpose of this paper is to discuss mainly in a qualitative way, the functions of gravity, to present some concrete instances where it has been important and to raise some questions that should be investigated further. Oil-recovery Agents The important natural agents for effecting oil recovery that may be originally available in a reservoir are gas, both dissolved in the oil and free in gas caps, encroaching edge water and gravity. Each of these agents can act in a dual capacity—physically to overcome the surface energies that hold the oil within the pores and mechanically to overcome viscous . resistance and to propel the oil through the porous reservoir rock to the wells. Advancing edge water displaces the oil from the pores and lifts it updip to structurally lower wells. Gravity drains the oil from the pores and flows it downdip to the wells. Gas displaces oil from the pores, entrains it in the gas stream and flows it to the wells, but gas in solution also affects the physical properties of the oil and thus can influence oil recovery by the other agents, whether or not the mechanical energy in the gas is utilized. Of the two functions of these agents, the more important is the ability to dis-

Jan 1, 1944

By George Mieyr, H. M. Ziesemer

Prior to 1909 that mountain of porphyry known as Sacramento Hill had hardly been touched though it had always been thought to contain ore. During that year, exploratory work was started by underground methods; drifting and raising continued until 1913. It was proved that a mineralized zone existed, the limits of which had not been determined ; so, because of the lower costs of exploratory work and the greater desirability of vertical sections, it was decided to prove the extent of the ore zone by churn drills. Drilling continued until 1917, when it seemed almost certain that the horizontal limits of the orebodies had been determined. Ore continued in depth in one direction beyond a point where it was economical to explore by churn drilling; this extension is still being developed by underground methods. The irregularities of the boundaries of the ore zones, together with the variable grades of ore encountered, made it necessary to drill on the corners of 100-ft. squares. Two ore zones were proved, known as the East and West Orebodies. The Sacramento Hill porphyry stock intruded into the Dividend fault. The fault ran roughly east and west with a dip to the south, having pre-Cambrian schists on the north against Paleozoic limestone on the south. This intrusion was accompanied by a silica breccia on the south periphery, along the limestone contact side. The ore lay in the silica breccia and in the porphyry, some distance from the breccia. NO ore was found in the heart of the porphyry mass on the north side, along the schist contact. The West Orebody is elliptic in shape, having a major axis of 1200 ft. (366 m.) and a minor axis of 800 ft. (244 m.); these diminish with depth until, at 300 ft., the axes are 500 ft. and 300 ft., respectively. The ore consists of chalcocite, some bornite, chalcopyrite, and considerable pyrite in a siliceous gangue. About 30 per cent. of the copper is caused by

Jan 1, 1923

By F. J. Martin, W. G. Hubler

The Beattie mine is at about the center of Duparquet township in the Province of Quebec, Canada. It is 22 miles northwest of the town of Noranda. The elevation is approximately 1200 ft. above sea level. This locality, long considered a favorable one from the geological point of view, has been prospected for over 20 years, but no discoveries of economic importance were made until the present orebody was found by John Beattie in 1930. The specific gravity of the ore is 2.77. The gold occurs in intimate association with the sulfides, pyrite and arsenopyrite, which in turn are very finely disseminated in a silicified porphyry. The bulk of the gold is associated with the pyrite, only a small proportion being with the arsenopyrite. There are small amounts of magnetite, ilmenite and chalcopyrite present in the ore. There is also some hematite in the ore that is mined from near the surface in the open pit. Metallurgical Problems and Methods or Attack 1. The ore is extremely hard and resistant to grinding. 2. The sulfide minerals are finely disseminated in the gangue. 3. The gold, in turn, is so intimately associated with the sulfides that grinding to even 5 microns will not release all of the values for cyanidation. 4. It is necessary to make a high ratio of concentration in order to obtain a product sufficiently high in gold to meet high shipping and treatment charges. Hardness of the Ore.—Owing to the extreme resistance of the ore to grinding, it was recognized that grinding costs would be high. Microscopic tests showed that grinding to 95 per cent minus 325 mesh would be necessary to liberate a sufficient amount of the values in order to obtain a tailing assaying 0.02 oz. gold per ton, which is considered to have the economical minimum gold content that can be obtained. It is not feasible to grind this hard low-grade ore (0.18 to 0.20 oz.) to 95 per cent minus 325 mesh, so it was necessary to overcome the problem in another way. The following method was decided upon: (1) Fine crushing to minus 1/4 in.; (2) relatively coarse primary grinding; flotation of low-grade concentrates in the primary and rougher circuits and discarding the

Jan 1, 1935

By A. S. Odeh

This paper analyzes the effect of limited entry to flow at the wellbore on the steady-state productivity of a well. Wells that have been opened to flow along a fraction of their productive interval are termed wells with limited entry. Previous work treated the cases of a partially penetrating well, a well producing from the central portion of the productive interval and a well in which several intervals equally spaced were open to flow. In this paper the open interval can be located anywhere within the productive interval. Thus, in a sense, it generalizes previous work. The finite cosine transform was used to arrive at a solution for steady-state flow of a slightly compressible fluid. The solution was programmed for a CDC 1604 computer. Numerical vaIues for rd = 660 ft, r, = 1/4 ft, and range of sand thickness of 20 to 200 ft are presented in graphical form. The effect of rd and r, values on the result is shown in a table. The correct calculation of skin and damage ratio in the presence of limited entry to flow is explained and illustrated by examples. Moreover, the paper shows how to calculate the net decrease in productivity due to the combined effect of limited entry and perforations. INTRODUCTION In some wells only a fraction of the productive interval is open to flow. Location of this fraction is usually dictated by formation characteristics and reservoir behavior. For instance, if a gas cap exists, the open interval is located away from the gas-oil contact to prevent any possible gas coning. Wells that intentionally have been opened to flow along a fraction of their productive formation are tened wells with limited entry. Obviously, unintentional completions of this type also exist. Limited entry to flow decreases well productivity. Magnitude of the loss depends on the fraction of the formation open to flow, on the thickness of the sand, on the location of the open interval and on the ratio of rd /r, where r , is well radius and rd is the drainage radius of the well. The use of pressure buildup data on producing wells to calculate the condition of the formation around the wellbore is an accepted practice. van Everdingenl and Hurst2 introduced the concept of she skin factor s considered to be due to a thin layer of different permeability immediately around the wellbore. These authors dealt with the case of a well of complete radial geometry, i.e., a well with open-hole completion that completely penetrates the formation. The presence of a low-permeability skin results in a loss of productivity, as does limited entry. Therefore, if pressure buildup data obtained on a well with limited entry are used to establish the presence or absence of skin (i.e., formation damage), and a correction is not made for this loss of productivity, the calculations would result in an erroneous skin value. They might indicate the presence of formation damage when in reality there is none, or they might indicate a value larger than the true value. This could lead to an incorrect basis for planning remedial measures. Muskat3 studied the problem of partially penetrating wells for the case of incompressible flow. He presented equations and figures which allow estimation of loss in productivity. Brons and Marting,4 using equations based on Nisle's work,5 studied the loss of productivity for three cases. The first was for a partially penetrating well; the second was for a well producing from only the central portion of a productive interval; and the third was for a well in which several intervals equally spaced were open to flow. Their work was for steady-state depletion-type reservoirs wherein the well radius of drainage is established and the fluid is considered to be slightly compressible. Considered in this paper is the problem of wells with limited entry in which the open intervals are located anywhere within the productive sand. The finite cosine transform is used to arrive at a

Jan 1, 1969