Search Documents

By J. P. G. Farr, R. Brownsword

THE role of solute segregation in the formation of cellular solidification substructures in tin and its dilute alloys is well-established, see, e.g., Ref. 1. Segregation has been shown to persist during cooling, enabling solidification structures to be studied from sections taken at some distance behind the interface. In the present work, a single crystal of commercial nickel, 99.965 pct, was examined in this way. The crystal was cut from the center of a rod given a single pass in an electron beam floating zone melter. Polished sections of a nickel specimen taken normal to the growth direction showed a very fine precipitate phase, the distribution of which varied over the section. The identification of the phase proved difficult because of the small amount present and the small particle size, about 1 p: but it was shown by probe microanalysis to contain only nickel and oxygen in detectable concentrations and was probably nickel oxide, NiO. Bulk analysis of the material before melting showed there to be only 3 to 4 ppm of oxygen present, thus demonstrating a very considerable segregation concentration effect. In some areas of the section the precipitate formed a discontinuous hexagonal network suggesting decoration of the cellular boundaries known to be present in the sample2 whereas in a restricted region the precipitate formed small clusters. Occasionally it could be seen that the clusters were at the intersections of an hexagonal network of cellular dimension. It was suggested3 that this was the result of enhanced segregation to the cell boundary intersections whereas general cell boundary segregation was insufficient to give a precipitate. Enhanced nodal segregation has since been demonstrated in a number of systems.1, 4-8 The development of a suitable electrolytic etching technique (perchloric acid 20 pct v/v; ethyl alcohol 70 pct; glycerol 10 pct; current below electropolishing plateau; 1 to 2 sec etching) suggested the association of the phase with regions of solute segregation (where ko < 1); in these regions anodic attack produced grooves or depressions. In a study of the variation of solidification substructures with degree of constitutional supercooling, Biloni et a1.&apos; appear to have used standard growth conditions and varied the solute concentration. They were able to produce in a series of individual tin crystals examples of substructure ranging from planar interface through various cellular structures to den- Fig. 1—Electroetched section taken normal to the rod axis; the center of the rod lies to the left and the periphery to the right of the micrograph. The variation of structure across the section is evident. Magnification 60 times. drites. It was possible in the present nickel crystal to observe a continuous range of substructures varying with degree of supercooling across a single section as shown in Fig. 1. Growth rate, 13 mm per min, and temperature gradient were essentially constant; the variation in structure is thought to be due to a radial gradient in solute concentration ahead of the solid interface. The liquid at the interface is likely to have been richer in solute toward the periphery of the zone, the result of curvature of this interface. The type of substructure was seen to vary with increasing constitutional supercooling as follows: a) region free of precipitate. top left, Fig. 1: 6) region of nodal precipitates which became arranged in hexagons on passing from the center of the rod: c) irregular hexagonal cells with incomplete boundary precipitation; d) regular hexagonal cells of decreasing size with complete boundary precipitation. Fig. 2 shows the transition from stage 6 and Fig. 3 shows the structure in stage d. Within stage 0, the range of conditions over which irregularly positioned nodes occur appears to be small and the nodes are soon recognizable as taking up positions at the intersections of an hexagonal network as the supercooling increases.

Jan 1, 1970

By T. Szaplonczay, D. E. Light

The auto-oxidation of sulfur dioxide to form sulfuric acid in commercially produced barren and recycle liquors, containing 1.66 and 4.56 gpl Fe respectively, from Elliot Lake was studied. A gas mixture, containing 3.5% SO2 and air was introduced into these liquors through a frit at a rate of 6.0g SO2 per hour per liter of solution. The barren and recycle were heated to 60°C. At the end of the first 24 hours of the process the concentrations of acid produced were 158 and 220 gpl H2SO4 for the barren and recycle respectively. Corresponding conversion efficiencies were 70 and 83%. In the period from 24 to 36 hours the rate of acid production decreased so that the H2SO4 concentrations at the end of 36 hours were 180 gpl for the barren and 260 gpl for the recycle; average conversions for the initial 36 hours were 55 and 68% respectively. Many investigators1&apos;2&apos;3 have considered the oxidation of sulfur dioxide to form sulfuric acid in aqueous solutions containing metallic ions. A summary of the work performed on this subject prior to 1946 has been presented by Keyes4 who described the auto-oxidation process as follows. Keyes also suggested that in this second reaction ferric ion serves as a catalyst for the conversion of sulfur dioxide to sulfuric acid. Neytzell-de Wilde and Taverner5 have reported on the use of auto-oxidation to produce a 4 to 5% sulfuric acid solution for use in a cyclic leach process at South African uranium plants. This paper describes investigations carried out to determine the feasibility of using the auto-oxidation process to produce sulfuric acid solutions of as high concentration as possible using commercially produced uranium plant barren and recycle liquors from the Elliot Lake region of Ontario. These liquors contained 1.66 and 4.56 gpl respectively of iron, chiefly in the ferrous state. This investigation is of particular interest to the uranium producers in Elliot Lake where the ores contain 3 to 4% sulfur, as sulfides. Flotation of these sulfides and roasting of same to produce SO, bearing gases have been successfully demonstrated using conventional methods.6&apos;7 Barren and recycle solutions, as described previously, are also produced in large tonnages by these uranium producers. The experimental method and apparatus used to examine the auto-oxidation process will be described first. Then the tests carried out on laboratory prepared aqueous solutions containing ferric sulfate to determine optimum conditions will be presented. The next section will describe the tests using the commercial barren and recycle liquors. A final section will summarize the conclusions of the work. EXPERIMENTAL APPARATUS AND PROCEDURES Two types of solutions were used in the tests, a laboratory prepared aqueous solution containing definite amounts of ferric sulfate, and commercially produced iron bearing solution obtained from a uranium leaching plant in the Elliot Lake area. Two liters of a solution to be examined were placed in a 3 in. diam by 30 in. long glass cylinder with a cross-sectional area of 7 sq in. A mixture of air, and SO2 supplied from a lecture bottle for convenience, was introduced into the bottom of the vessel through a standard 30 mm glass frit, 700 sq mm in area. The temperature of the apparatus was controlled by a heating tape and variable transformer. Exhaust gases were vented to atmosphere. At the end of the test period the gas flow was shut off and the solution was analysed for H2SO4, Fe ++, and Fe +++, by conventional means. Four variables were examined using the laboratory prepared aqueous solution of ferric sulfate. First, the effect of SO2 concentration, from 1 to 1076, in the feed gas mixture was considered. Second, the temper-

Jan 1, 1964

By S. E. Haszko

Fused alumina or silica crucibles were used as the containing vessel. X-ray powder photographs were taken with CrKa radiation and the use of Straumanis type Norelco cameras of 114.6 mm diam. Crystallographic data for these compounds are shown in Table I. These results are in agreement with others of this series reported previousiy by Wernick and Geller.l The abnormally large atomic volume of Eu and Yb metal3 is manifested in EuA12 and YbAl2, when one compares them with the compounds reported in Ref. 1. However, the behavior of Yb in the Ni compound is the same as that observed in Ni5Yb having the Cu5Ca structure.4 Thus, it appears that Yb has a valence closer to 3 only in the Ni compounds; i.e.. the 2s and Id electrons are lost to the conduction band. 1,4 Europium in EuAl2, appears to have a valence closer to 2. In previous work.&apos; X-ray patterns of ingots of NdCo2 indicated a multiphase material with faint indication of the presence of a phase having the MgCu2 structure. It was thought that NdCo2 formed peri-tectically from the melt, resulting in a multiphase system when cooled under nonequilibrium conditions. An X-ray pattern of a sample from a melt cooled more slowly than in past work showed that the major phase was NdCo2. The lattice constant, Table 1, is in excellent agreement with the value one can predict from the data of Ref 1. One of the other phases was identified as Co,Nd. The author wishes to thank J. H. Wernick for his guidance in this work, and D. Dorsi for the preparation of these compounds. &apos;J. H. Wernick and S. Geller: AIME Trans., in press. &apos;J. H. Wernick and S. E. Haszko: to be published. &apos;F. H. Spedding and A. II. Daane: Progress in Nuclear Energy, Series 5, Eds.: H. M. Finniston and J. P. Howe, McGraw-Hill Book Co., 1956. &apos;S. E. Haszko: to be published. &apos;J. H. Wernick and S. Geller: unpublished work. 6J. 11. Wernick and S. Geller: Acla Cryst., 1959, vol. 12, p. &apos;162. The Influence of Hydrogen on the Lattice Parameters of Ti-Sn Alloys A. Coucoulas and H. Margolin A reinvestigation of the lattice parameters of Ti-Sn alloys by the present authors has revealed consistently higher c and a values than those obtained by Worrier. The difference is most pronounced in the c-parameters which are, therefore, used as a basis of comparison. This discrepancy was not due to air contamination, since precautions were taken to exclude this possibility. Specimens for Debye-Scherrer photograms were prepared by arc-melting 15-g buttons of Bureau of Mines titanium and 99.99 pct Sn, with compositions of 6, 8, 10, and 12 at. pct Sn. These buttons were forged under an oxygen-acetylene torch to 1/8-in. sq rods to produce relatively fine grained material. Scale and some surface were ground off, and the rods, after wrapping in molybdenum and titanium sheet, were vacuum annealed 15 min at 800 °C to remove hydrogen. Heat treatment of one of the samples at 875°C to produce ß and reveal a at the surface showed no surface contamination. Following the vacuum treatment, the specimens were wrapped in molybdenum and annealed for 1week at 800°C under two atmospheres of argon. After water-quenching, the rods were ground so that the thickness tapered to 0.1 mm at the tips. The ground specimens were then recapsuled as previously and reannealed 1 hr at 800°C to remove cold work. The

Jan 1, 1961

By C. G. Dunn

The measurement of interfacial teusions or grain boundary energies in metals is an important metallurgical problem, especially since it bears on growth and nucleation processes. Statistical methods of measuring equilibrium grain boundary angles, which relate interfacial tensions, have been used by some investigators1&apos;2 but more direct methods would be preferred. A direct way, based on a simple extension of a successful method of growing single crystals of silicon ferrite to predetermined orientations in flat specimens,3 is to produce three-grain specimens in such a way that the equilibrium common grain boundary will be perpendicular to the surface of the specimen. The angles to be measured then appear as the grain boundary angles in the surface of the specimen. The method of producing a single crystal specimen with a predetermined orientation is basically the same as that employed by Yoshida and Fuji-wara4 in their work on aluminum wires. The specimen, prior to any single crystal transformation, must have a matrix which will support the growth of a crystal of the desired orientation. Growth may occur through exaggerated grain growth or, if the matrix is strained a critical amount. by normal recrystallization. In either case the matrix must have stability at the temperature used to effect the transformation, this stability appearing as a long induction period for exaggerated grain growth or for the formation of recrystallization nuclei. Additional control is gained by using a high temperature gradient through which the specimen is moved at a suitable rate. To obtain the desired orientation, the specimen is fed a short way into the furnace producing one or more crystals in the hot end. After the specimen is removed from the furnace, the orientation of a crystal is determined, so that this crystal may be reoriented by properly deforming a narrow piece of the matrix between the end crystal and the rest of the specimen. This part of the specimen in the case of silicon ferrite is preferably held at red heat during the reorienting process. Fig 1 shows a specimen which is ready to be transformed into a single crystal through growth of a reoriented "seed" crystal. When the method just described is applied to the production of a three-grain specimen two crystals are grown first side by side in one end, the specimen is then reversed and the third grain grown from the opposite end. A suitable group of grains each of different orientation is one where all three grains have the same crystallo-graphic plane in the plane of the specimen. Fig 2 shows a photograph of a three-grain group prepared as described. The notches are introduced in the open ends of the grain boundaries to anchor them during the final annealing operations which ultimately should bring the grain boundaries to the lowest energy configuration. Two-grain groups with different crystallographic planes in the plane of the specimen can be similarly prepared and treated. If the two grains have different surface (gas to metal) energies per unit area, the equilibrium condition leads to a curved grain boundary.* * This feature of the problem was pointed out by J. c. Fisher. References 1. Cyril Stanley Smith: Grains. Phases and Interfaces: An Interpretation of Microstructure. Trans. AIME 175, 15. Met. Tech. TP 2387, June 1948. 2. D. Harker and E. Parker: Grain Shape and Grain Growth. Trans. A.S.M. (194,5) 34, 156-195. 3. C. G. Dunn, A. Seddon, and R. Wylie: Unpublished Work, 1946-1947. 4. Takeo Fujiwara: A Method of Producing A Long Single-Crystal Wire of Aluminum with any Desired Crystallographic Axis. Jnl. of Sci. Horoshima Univ. A, (1939) 9, No. 3, 227.

Jan 1, 1950

By H. Margolin, A. Coucoulas

Fused alumina or silica crucibles were used as the containing vessel. X-ray powder photographs were taken with CrKcll radiation and the use of Straumanis type Norelco cameras of 114.6 mm diam. Crystallographic data for these compounds are shown in Table I. These results are in agreement with others of this series reported previousiy by Wernick and Geller.l The abnormally large atomic volume of Eu and Yb metal3 is manifested in EuAl2, and YbAl2, when one compares them with the compounds reported in Ref. 1. However, the behavior of Yb in the Ni compound is the same as that observed in Ni5Yb having the Cu5Ca structure.4 Thus, it appears that Yb has a valence closer to 3 only in the Ni compounds; i.e.. the 2s and Id electrons are lost to the conduction band.1,4 Europium in EuAl2 appears to have a valence closer to 2. In previous work.&apos; X-ray patterns of ingots of NdCo2 indicated a multiphase material with faint indication of the presence of a phase having the MgCu2 structure. It was thought that NdCo2 formed peri-tectically from the melt, resulting in a multiphase system when cooled under nonequilibrium conditions. An X-ray pattern of a sample from a melt cooled more slowly than in past work showed that the major phase was NdCo2. The lattice constant, Table 1, is in excellent agreement with the value one can predict from the data of Ref. 1. One of the other phases was identified as Co5Nd. The author wishes to thank J. H. Wernick for his guidance in this work, and D. Dorsi for the preparation of these compounds. &apos;J. H. Wernick and S. Geller: AIME Trans., in press. &apos;J. H. Wernick and S. E. Haszko: to be published. &apos;F. H. Spedding and A. II. Daane: Progress in Nuclear Energy, Series 5, Eds.: H. M. Finniston and J. P. Howe, McGraw-Hill Book Co., 1956. &apos;S. E. Haszko: to be published. &apos;J. H. Wernick and S. Geller: unpublished work. 6J. 11. Wernick and S. Geller: Acia Cryst., 1959, vol. 12, p. &apos;162. A reinvestigation of the lattice parameters of Ti-Sn alloys by the present authors has revealed consistently hiher c and a values than those obtained by Worrier. The difference is most pronounced in the c-parameters which are, therefore, used as a basis of comparison. This discrepancy was not due to air contamination, since precautions were taken to exclude this possibility. Specimens for Debye-Scherrer photograms were prepared by arc-melting 15-g buttons of Bureau of Mines titanium and 99.99 pct Sn, with compositions of 6, 8, 10, and 12 at. pct Sn. These buttons were forged under an oxygen-acetylene torch to 1/8-in. sq rods to produce relatively fine grained material. Scale and some surface were ground off, and the rods, after wrapping in molybdenum and titanium sheet, were vacuum annealed 15 min at 800 °C to remove hydrogen. Heat treatment of one of the samples at 875°C to produce ß and reveal a at the surface showed no surface contamination. Following the vacuum treatment, the specimens were wrapped in molybdenum and annealed for 1 week at 800°C under two atmospheres of argon. After water-quenching, the rods were ground so that the thickness tapered to 0.1 mm at the tips. The ground specimens were then recapsuled as previously and reannealed 1 hr at 800°C to remove cold work. The

Jan 1, 1961

By M. T. Hepworth, W. B. Sample

HYDROGEN solubility and linear contraction measurements were made at constant temperature on an alloy of titanium of constant oxygen-to-titanium molal ratio but variable hydrogen content. A cylindrical specimen of titanium (0.25 by 1.6 in.) containing 0.75 at. pct 0 and less than 0.03 at. pct N was cast from a master button of iodide process titanium which had been alloyed with titanium dioxide. Four vacuum fusion analyses, which were made along the length of the cylinder after the hydrogen solubility studies were made, revealed a variation of oxygen content of less than 0.02 at. pct. The specimen was introduced into a quartz furnace tube, annealed and outgassedat 1050"~ for about 1 hr, and then held at 800" * 0.5" for about 30 hr, during which latter time experimental data were taken. The leak rate to the furnace chamber was not sufficient to contaminate the specimen during the run as determined by leak-rate studies and vacuum fusion analyses for oxygen and nitrogen before and after the runs. The furnace chamber was attached to a modified Sieverts apparatus used to introduce measured quantities of purified hydrogen to the specimen. A quartz pushrod transmitted changes in length of the specimen to a Chevenard dilatometer. The push-rod passed through a vacuum grease seal to the dilatometer which amplified motion of the rod by a factor of 319. During hydrogen addition, the pushrod did not contact the specimen. Measured quantities of hydrogen were added to the specimen and equilibrium hydrogen pressures recorded as a function of hydrogen content. The solubility data, which appear in Fig. 1, agree well with a separate investigation made with a different apparatus. The solubility limit of the hcp a phase appears as an abrupt discontinuity in slope at 3.4 at. pct H. The solubility plot has been extended as a dashed line at this discontinuity in order to emphasize the discontinuity. The hydrogen content at which bcc P appears is not clearly defined. An arrow indicates solubility data were taken upon hydrogen addition. Upon reaching the arbitrary maximum hydrogen content of the run, the quartz pushrod was pressed against the specimen in order to record the change in length with hydrogen removal. A pressure of about 100 g per sq cm was required to overcome the friction of the vacuum seal in order to obtain reproducible linear contraction data. The contraction ratio ~2/1", change in length divided by original length, was set equal to zero for the maximum hydrogen content. The relative contraction of the specimen was observed upon removal of hydrogen in the following manner. The system was opened to the pumps for a few seconds and an unknown quantity of hydrogen was removed. The system was then isolated from the pumps by closing a stopcock and allowed to return to equilibrium. When the temperature returned to 800°C, the pressure stabilized, and contraction ceased, measurements of contraction and pressure were made. The hydrogen content of the specimen was then deduced by measuring the equilibrium PIydrogen pressure and referring to the solubility plot. Linear contraction was then plotted against interpolated values of atomic percent hydrogen. The justification for this procedure is the established reversibility of the hydrogen equilibrium.&apos; Uniaxial compression was assumed to have no effect on hydrogen pressure. The isothermal linear contraction data are plotted on Fig. 1. An arrow indicates data were taken upon removal of hydrogen. The solubility limits of the two phase a i /3 region can be identified by discontinuities ill slope of the dilatometric plot at 9.1 and 3.4 at. pct H, agreeing well with other studies.&apos; Dashed extensions of the plots emphasize the discontinuities. Isothermal studies of expansion made upon hydrogen addition gave curves of much smaller slope and less pronounced discontinuities. A uniaxial compressive stress tends to accentuate volume changes in going from the more open bcc phase to the hcp phase.2 Incomplete data on ex-

Jan 1, 1962

By Ellis H. Gates

BENEFICIATION of the manganese oxide ores at Three Kids Mine near Henderson, Nev., has evolved over a period of years. Commercial application of the process is on a secure basis, and an effective working hypothesis has been formulated to help solve the problems encountered in flotation. An outstanding difference between the Manganese Inc. operation and other flotation processes is the necessity for high recovery of slime mineral values. Part of the manganese minerals in the Three Kids ore deposit occurs as primary slime or as minerals that are easily slimed by grinding. High recovery of this slime portion is essential to an economic overall manganese recovery. The aim of much of the research at Manganese Inc. was to recover these slimed and finely ground minerals by flotation. Early Agglomeration Processes: Tunbridge&apos; in 1880, followed by Everson2 in 1886 and Cattermole" in 1904, discovered that under certain pulp conditions precious metals and sulfide minerals could be agglomerated if enough soap or oil were mixed into the pulp slurry. These agglomerated particles, Which under ideal conditions ranged from 1/16 to 1/4 in. diam, were recovered by screening, tabling, and hydraulic classification. Even flotation by air occluded in the agglomkrate particles by vigorous stirring was suggested. Cattermole nearly succeeded in getting his process into commercial operation, but it was finally abandoned, presumably because he could nat compete with the low reagent requirements of the new agitation froth process. Since Cattermole&apos;s time Christensen in 1921, Borcherdt4 in 1926, and Chapman and Littleford- in 1934 have attempted to apply the principles of agglomeration. In the light of current research at Manganese Inc. on conditioning of pulp at high energy input levels, it is interesting to note the variety of equipment such as tumbling mills, mixing drums, and shakers described by Borcherdt in his patent to produce the agglomerated particles. Ore Characteristics: Manganese in the Three Kids ore occurs as a &apos;complex mixture of manganese oxides commonly Known as wad. The manganese minerals have Been identified as psilorflelane, hollandite, coronadite, and pyrolusite with minor amdunts of rhodonite and rhodochrbsite. The ppincipal gangue miherals are quaktz, opal, kaolinite, montmoril-lonite, calcite, gypsum, fcelesitite, and barite. Most of the mangandse ore minerals are either porous and sponge-like in structure or soft clay-like masses composed of fine grained mineral particles approaching the size range of colloids. Consequently the ore minerals from the Three Kids mine have relatively large surface areas and high void content per unit weight. The specific area of various manganese ore samples measured at the California Research Corp. laboratories ranged from 32 to 58 sq m per g. The great surface area and high void content explains in part the unusually high reagent consumption required in the treatment of this ore. Current Milling Practice: At Henderson6 he ore is crushed to —1 in. and ground with rod mills in a closed circuit with spiral rake classifiers and cyclones. Sulfur dioxide solution is added to the pulp as it leaves the grinding circuit, immediately followed by addition of a reagent mixture of soap, oil, and wetting agent in the form of an emulsion. The reagents are initially well mixed into the pulp during their passage through centrifugal pumps to the conditioning equipment. All reagents are added prior to conditioning. The intense conditioning or mechanical stirring of the pulp, in which large amounts of power are consumed, is the principal difference between the flowsheet used at Manganese Inc. and a standard flotation circuit. As much as 38 kw-hr of energy per dry short ton of ore in a pulp containing 18 to 23 pct solids is used for conditioning. After conditioning, the pulp passes to a flotation circuit that consists of one roughing stage, a scav-

Jan 1, 1958

By R. M. N. Pelloux

This study of aluminum-copper alloys had two aims: 1) To determine the effect of the amount and distribution of a second phase, CuAl2, on the creep-rupture strength, ductility, and fracture characteristics of the alloys. The work of Gemmell and grant&apos; on single-phase aluminum-copper alloys provided a basis for the present study. 2) To attempt to provide a relation between the microstructure and strength of two-phase alloys deformed at comparatively high temperatures (greater than 0.45 T,). The creep behavior of the two-phase magnesium alloys Mg;Ce and Mg-A1, has been treated by Roberts. 9 In work reported by Sully and Hardy4 and by Underwood, Marsh, and Manning~ on A1-Cu two-phase alloys, and also in a portion of the work of Gemmell and grant,&apos; aging took place during the creep tests. &apos;In the present work, overaged aluminum-copper alloys were subjected to creep deformation at two temperatures, 500 and 700OF. The overaging treatments to produce the precipitate dispersions were performed prior to the test, at temperatures which were the same as the ultimate respective test temperatures. Hence, the present study is concerned with the creep behavior of stable (in contrast to "underaged") two-phase A1-Cu alloys, i.e., alloys in which no depletion of the solid-solution matrix occurred during: creep. MATERIALS AND PROCEDURE A 2 and a 3 pct Cu alloy, supplied by Alcoa, were studied; Table I shows the compositions. The grain size of the specimens, 0.9 to 1.0 mm, was achieved by annealing the machined test bars for 2 hr at 1000°F, followed by furnace-cooling to 900°F, and homogenizing for 4 hr. Both compositions are in the single-phase condition at 900°F. Two types of overaged dispersions, termed "over-aged I" and "overaged 11" were prepared after the grain size and the homogenization anneals. The overaged I alloys were prepared by quenching to room temperature after homogenization, aging at either 500&apos; or 700°F for 72 hr, and air-cooling to room temperature. The overaged I1 alloys were prepared by furnace-cooling after homogenization, to either 500&apos; or 700°F, and holding at the necessary temperature for 72 hr. The times for furnace-cooling from 900°F to 700° and 500°F were, respectively, about 2 and 3.5 hr. The structures of the A1-2 pct Cu alloys are shown in Fig. 1 (overaged I) and in Fig. 2 (overaged 11). A comparison of Figs. 1 and 2 shows that in the overaged I alloys the precipitate particles along the grain boundaries are much more closely spaced and the grain boundaries are straighter than they are in the overaged I1 alloys. Further, the particle size and spacing in the grains are smaller than in the overaged I1 alloys. Microstructures of the A1-3 pct Cu alloys have not been shown; the structures of these alloys differed from those of the A1-2 pct Cu alloys only in that the distribution density of the particles was greater. The creep specimens had a gage section 1 in. long with a diameter of 0.155 to 0.195 in. Before testing, specimens were electropolished in a solution of 100 cc glacial acetic acid, and 30 cc of 60 pct perchloric acid, at 40&apos; to 50°F, at 24 v. The specimens were kept refrigerated prior to testing to avoid precipitation at room temperature. Constant stress creep tests were conducted; the load was applied 75 min after heating of the specimens to test temperature had begun. EXPERIMENTAL RESULTS Creep-Rupture—Fig. 3 shows the log stress-log rupture life plotfor the overaged alloys studied, and also for the underaged A1-2 pct Cu alloy.&apos; At 700°F, the stress-rupture life relationship is nearly independent of both the amount of precipitate (i.e., composition) and of the type of overaging treatment (i.e., precipitate dispersion). At 500°F it is apparent that the increase in rupture life that was ex-

Jan 1, 1960

By O. C. Holbrook, George G. Bernard

A new theoretical treatment has been obtained for the behavior of pattern waterflood injection wells when closed in. Two cases are treated: Case I where oil and water are assumed to have the same properties, and Case 2 where they arc different. In applying the method, one plots log (p — p,) vs closed-in time, where p is well-bore pressure at any tims and p, is static pressure. The value of p. is determined by trial and error as that value which makes the plot linear at large time. A value for the permeability-thickness product can be determined from the intercept of this linear part, and a value of the skin factor from the injection pressure at time of closing in. Application of the method to data from water floods at three fields seems to give reasonable results. For the case of unit mobility ratio, it is proved that this new method should give the same value for permeability-thickness product as the conventional pressure build-up method. In addition, the new method gives correct values for static pressure, whereas the conventional method does not, often indicating negative static pressures. The new method may be used in cases where the surface pressure persists after closing in as well as in cases where it does not. INTRODUCTION It is of considerable interest and importance to be able to determine the characteristics of the reservoir in an area surrounding a water injection well. Thus, if we can determine early in the life of an injection well that there is a considerable "skin effect", remedial measures can be started before a full-scale pattern flood begins. Similarly, if it can be shown that a gradual buildup of skin effect is occurring with time, measures to free the water of plugging material can be taken. Determination of static pressure in the water-injection well may show that the water is entering a thief zone and not the desired reservoir. Finally, determination of the permeability of the sand around the injection well will allow estimation of the future relation between injection pressure and rate. It should be possible to determine average reservoir permeability, skin effect and static pressure from pressure fall-off data. However, at the time we began work on this subject, it was thought that no adequate theory on which to base such determinations&apos; was available. According to the conventional method which considers the reservoir to be filled with one fluid of small compressibility (see Van Everdingen, Joers2, and Nowak2), shut-in pressure is plotted vs log where is injection time, and At is closed-in time. The physical significance of injection time, may well be questioned in this case, since in a reservoir completely filled with a single fluid (as required by this theory) and with input and output rates equal, the pressure behavior after an initial transient is independent of t,. Attempts by our Tulsa area to use this theory led to negative values of static pressure in most cases. Because of these limitations of the method discussed above, it was decided to attempt to develop a new theory of pressure behavior in water injection wells, one which would apply when there is a gas saturation, as is so often the case in water floods. In the following treatment the assumptions and basic equations are given first, then the method of application of the equations. A complete example is given to clarify details of application. All difficult mathematics has been placed in the appendices so that the reader can follow the text without difficulty. However, if he wishes only to apply the results without knowing the basis for them, he can learn how to do this from reading only the sections entitled "Plotting of Experimental Results" and "Example." ASSUMPTIONS AND BASIC EQUATIONS Statement of Problem It will be assumed that a horizontal layer of constant thickness contains in its pore system a mixture of oil, gas and water. While water is being injected into this pore- system through a well at constant rate, an oil bank is built up, gas being expelled from the space taken by the oil as shown in Fig. 1. The saturations within each

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-B alloys has been measured up to the solubility limit for the formation of boron nitride. The activity coefficient of nitrogen increases with increasing boron content in the range 0 to 7 wt pct B. From experimen -tal data, values have been calculated for the B-N interaction parameter e3 at temperatures in the range 1550" to 1750°C. A value of 0.038 has been estimated for the boron self-interaction parameter eg at 1550°C. The standard free energy of decomposition of boron nitride into the elements dissolved in liquid iron has been determined to be: ?F° = 45,900 -21.25T in the range from 1550° to 1750°C. The nitride is assumed to be of composition BN. BORON nitride has an unusual combination of properties which make it appear attractive in a wide range of engineering applications. Some of its more important and most recent applications are in the nuclear area, particularly in connection with the liquid-metal cooled reactor concept now receiving considerable emphasis. Boron nitride has a high degree of stability at elevated temperatures. It also has excellent ma-chinability and the ease with which its crystals deform suggests applications as a lubricant. These properties stem from a hexagonal layer-type structure similar to the structure of graphite. One of its primary uses to date has been for seals in liquid-metal pumping systems. It is also used in nuclear reactors as an insulating layer to separate two solid metals which are not themselves compatible under the conditions of temperature and atmosphere in which they are used. Its inertness to liquid metals has also suggested use as a mold-release agent in casting processes. In addition to its excellent machinability and reported inertness to liquid metals such as iron, silicon, aluminum, copper, and zinc, boron nitride has high thermal conductivity and excellent thermal shock resistance. This combination of properties would make it appear ideal as a refractory crucible material for refining of high-purity liquid metals, for example high-quality steels. However, since it is known that concentrations of boron as low as 50 ppm can have a marked effect on the physical properties of certain steels,&apos; in particular on the creep and stress-rupture properties, an investigation was undertaken to define accurately the chemical equilibrium among boron, nitrogen, and liquid iron in the range of steelmaking temperatures. EXPERIMENTAL PROCEDURE Two experimental approaches to this problem were employed: a Sieverts&apos; method and a quenching method. In the first method, the Sieverts&apos; technique was used to measure the equilibrium nitrogen solubility in liquid Fe-B alloys of 0 to 7 pct B as a function of nitrogen gas pressure over the melt. The solubility limit of the boron nitride phase formed was determined by the point of departure of the nitrogen absorption from Sieverts&apos; Law. This technique has been applied to liquid Fe-Ti alloys by Rao and parlee,&apos; to liquid Fe-A1 alloys by Evans and Pehlke,3 and to solid Fe-V alloys by Fountain and Chipman.4 In the second method a melt of liquid iron was held in a crucible of boron nitride under a known partial pressure of nitrogen gas. After thermodynamic equilibrium was attained, the melt was quenched in a stream of helium and then analyzed by wet-chemical methods for boron and nitrogen. The Sieverts&apos; apparatus used in the first method was essentially of the same design as the one described by Pehlke and Elliott.5 The charge materials were vacuum-melted high-purity iron (Ferro-vac E) supplied by the Crucible Steel Co. and -325 mesh boron powder supplied by Cooper Metallurgical Associates of Cleveland, Ohio. The boron contained less than 0.02 wt pct O, according to supplier&apos;s analysis. Recrystallized alumina crucibles were used to contain the melt. Examination of solidified melts showed these crucibles to be satisfactory with no evidence of any reaction or physical penetration of the crucible wall by the melt. The melt temperature was measured by a disappearing filament-type optical pyrometer sighted vertically downward on the melt surface through a 1/4-in.-diam sight hole in the crucible lid. The pyrometer was calibrated against the melting point of pure iron in the same apparatus, taking the emissivity of

Jan 1, 1964

By P. G. Shewmon

Radioactive MgZA has been used to study the rate of self-diffusion in oriented single crystals of magnesium in the temperature range 468O to 635OC. The diffusion coefficients parallel and perpendicular to the c-axis are: Dl, = 1.0 exp (—32,200IRT) cm2 per sec and Dl = 1.5 exp (—32,500IR T) cm Qer sec. The ratio Dl/Dll was found to vary from 1.13 at 468 to 1.24 at 575 C. Assuming a vacancy mechanism, an explanation of this aniso-tropy of diffusion follows from a consideration of the difference in the saddle points for diffusion in and out of the basal plane. RECENT discovery of radioactive Mg2"&apos;-&apos; has made possible the study of self-diffusion in magnesium. The experimental procedure and the results of a study of diffusion in polycrystalline magnesium have been described in an earlier paper.V he present work is an application of the same techniques to the study of self-diffusion in oriented single crystals of magnesium. In the general diffusion problem the diffusion coefficient is a second order tensor relating the two vectors, the diffusion flux, and the concentration gradient. In a hexagonal lattice, such as magnesium, the complete determination of the diffusion coefficient D as a function of direction in the lattice requires a knowledge of D,, and D,, i.e., the diffusion coefficients parallel and perpendicular to the c-axis, respectively. It can be proven quite generally that in a hexagonal lattice D is independent of direction in the basal plane, and that out of the basal plane it varies with 0, the angle between the c-axis and the direction of diffusion, according to the equation D(B) = D,,cos2B + D,sin2B. [I] The proof of Eq. 1 depends only upon the symmetry elements of the hexagonal lattice and upon the transformation properties of a second order tensor." Therefore, Eq. 1 holds for any mechanism of diffusion and any c/a ratio. Experimental Procedure The experimental procedure used with polycrystalline specimens can be briefly outlined as follows. Radioactive Mg" was produced by bombarding a NaCl crystal with 350 mev protons and was chemically separated from the target as MgO. The Mg" was then vapor deposited on a specially cleaned magnesium specimen by heating the MgO on a tantalum ribbon in a vacuum. During the diffusion treatment, oxidation and vapor loss of the radioactive material were minimized by annealing the samples in pairs with the active faces in contact, each pair being inside a magnesium container, which was in turn surrounded by an argon atmosphere in a sealed Pyrex tube. The distance-activity profiles were obtained by measuring the activity of thin sections cut parallel to the original interface with a lathe. The only technique which was peculiar to this work was the preparation and orientation of the single crystal specimens. The single crystals used in this work were grown by E. C. Burke of the Dow Chemical Co., using a modified Bridgman method, in which the furnace and specimen were stationary while the temperature gradient moved.&apos; In growing these crystals the starting material was distilled magnesium, the crucibles were machined from Acheson electrode graphite, and the furnace atmosphere was tank argon. The crystals were grown from sublimed magnesium with the following analysis: 0.0002 pct Al, 0.0017 pct Fe, 0.0009 pct Mn, 0.0001 pct Ni, 0.0006 pct Pb, and less than 0.01 pct Ca, 0.0001 pct Cu, 0.001 pct Si, 0.001 pct Sn, and 0.02 pct Zn. The two crystals used were roughly lh in. diam and eight in. long. The c-axis made angles of about 7" and 78", respectively, with the specimen axes. If the values of D obtained by the use of these two crystals are taken equal to D,, and D,, respectively, the error introduced by this assumption is less than 1 pct. This can be shown by combining Eq. 1, the identity sin% + cos&apos;8 = 1, and the experimental fact that DJDn in magnesium was always less than 1.25.

Jan 1, 1957

By J. D. Verhoeven

The effectiue distriblltion coefficient has been Measured in a series of vertical, normal freezing experirtzents with large current densities passing through the solid-liquid interface. The results indicate that the effect of the current on solute redistribution is due to electvotransport in the liquid. The high currents produced extensive mixing in the liquid which was considerably reduced by solidifying in small lubing. Analysis of the convection indicates that it probably vesulls from a horizontal temperature gradient produced by the Joule heating- of the electvic crirver~t. Due to the strong dependence of this convection upon the specimen radius, it is conclnded that only for specit~ens with radii of less than somewhere between 1 and 2 mm wilt electric field freezing be getlerally effec-tire at enhancing the purification of zone-melting experittierats in loe-melting alloys. Experiments on 0.8-mm lubes illustrate some interesting potential applications of this techniqne as a means of solute control on smcrll specimens. In a number of papers published within the last few years&apos;-4 it has been found that passage of large dc currents through the solid-liquid interface of a freezing alloy produces a change in the solute redistribution accompanying the solidification. It had been predicted theoretically by Hucke et al.s and by Pfann and Wagner that such an effect would occur as the result of electrotransport within the liquid boundary layer at the solid-liquid interface. These authors independently derived the following relation between the effective distribution coefficient and the variables of the process: Where k0 is the equilibrium distribution coefficient, V is the mobility of the solute relative to the solvent, E is the electric field intensity, D is the solute diffusion coefficient, R is the rate of interface motion, and 6 is the boundary layer thickness. Both groups of authors show that this equation predicts the possibility of extending the purification ability of zone-melting experiments by the addition of an electric current. However, there are other effects in addition to electro-transport which could be produced by the high dc current and might, perhaps, invalidate the applicability of Eq. [I]. For example, high electric current might affect the interface reaction or perhaps the equilibrium distribution which was assumed to exist at the interface. It was the purpose of this work to determine the applicability of Eq. [I] by systematically investigating a simple system for which all of the necessary parameters were known. It was of particular interest for speculating on the potential usefulness of this technique to determine the maximum practical field intensities obtainable, and the effect of these high fields upon convective mixing in the liquid. The initial work in this study was published in a previous paper3 which will be referred to as I. In that work, a current density of 2000 amps per sq cm was used with specimen diameters of 5 mm. The results gave a qualitative confirmation of Eq. [I.], and also showed that a large amount of convective mixing was produced in the liquid by the current. The present study is an extension of that work to smaller specimen diameters and higher current densities. Two points were overlooked in I and will be emphasized here: a) the value of ko has not been well-established in the Sn-Bi system and b) the observed convection could be due to thermal convection produced from the Joule heating. EVALUATION OF k0 To evaluate Eq. [ I.] it is necessary to know the value of the equilibrium distribution coefficient, k,. Tn I the value of k, was taken as 0.3 from a published phase diagram.7 According to ansen&apos; the best data on the phase boundaries of the Sn-Bi system are those of Davidson.5 The data of Davidson give a k, value ranging from 0.21 to 0.25 for the compositions studied in this work, or an average value of around 0.23. In a recent publication, Rigaud and Tougas&apos;10 determined ko by means of a solidification technique. For an alloy of approximately the same composition as that used in this work they obtained a ko value of 0.39. Hence, there is considerable uncertainty in the value of ko and, consequently, a series of experiments were made to determine k, more accurately.

Jan 1, 1968

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.&apos; &apos; The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By F. S. Pettit

The oxidation of Ni-3 to 25 wt pd Al alloys has been studied in 0. 1 atm of oxygen at temperatures between 900° and 1300°C. These alloys have been found to oxidize by three different mechanisms which depend on the temperature of- oxidation and the alloy composition. Two of the three mechanisms do not permit a continuous layer of Al,0, to be formed on the alloy surface and the oxidation rates are greater than that for pure nickel. The third mechanism results in the formation of an external A1203 scale and lke oxidation rates are about three orders of magnitude smaller than those for pure nickel. The minimum amount of aluminum required for the formation of external scales of A L,0, has been determined. NICKEL-base alloys are currently the main source of materials for use at elevated temperatures in gas turbine engines. These alloys are usually coated to obtain oxidation resistance. Coatings on nickel-base alloys are frequently formed by reaction of the alloy with aluminum whereby alloyed nickel aluminides are formed. The alloyed nickel aluminides provide protection to the nickel base alloy because external scales of A1203 (alumina) are formed during oxidation and mass transport through A120, is slow in comparison to mass transport through most other oxides. In view of the protective properties of A1203, it is important to know how much aluminum is required in these alloys in order to form external scales of AlzO,. The present paper is concerned with the oxidation kinetics and the oxidation mechanisms of Ni-A1 alloys and the minimum amount of aluminum required in these alloys for the formation of external scales of Alz03. THEORETICAL CONSIDERATIONS When a Ni-A1 alloy is heated in oxygen at elevated temperatures, the following reactions can take place on the surface of the alloy where the oxide phases are assumed to be virtually pure: These oxide phases are in the form of nuclei scattered over the surface of the alloy and, in view of their rapid formation, they need not be in equilibrium with the alloy. As the oxidation process continues, equilibrium between the alloy surface and the oxide phases is approached and the stability of the oxide nuclei is determined by the composition of the alloy at the alloy/oxide interface because of the following reactions: 3NiA1204 + 2A1 (alloy) = 4AlzO3 + 3Ni (alloy) [41 4Ni0 + 2Al (alloy) = NiA120, + 3Ni (alloy) [ 5 1 Application of the mass-action law to Eqs. [4J and [5J yields the following equilibrium conditions for these reactions: where aA1 and aNi are the activities of aluminum and nickel, are the standard free energies of formation of NiO, A1203, and NA1204, respectively, R is the gas constant, and T is the absolute temperature. If the composition of the alloy at the alloy/oxide interface is such that (akl/ahi) is greater than the equilibrium values defined by Eqs. [6] and [7], then Reactions (41 and [5] will go to the right as written. Conversely, if the alloy composition is such that the activity ratio (aLl,/aki) at the alloy/oxide interface is less than the equilibrium values, then Reactions [4] and [5] will proceed to the left. The equilibrium activity ratios in Eqs. [6] and 171 can be calculated since values for the standard free energies of formation of the oxide phases are available. Standard free energies of formation for NiO and A1203 have been tabulated by Elliott and ~leiser.&apos; The standard free energy of formation for NiA1204 can be obtained from the data of Tretjakow and Schmalzried.&apos; The results of these calculations are tabulated in Table I. Table I shows that the following inequality is valid over the temperature interval 900" to 1300°C: (Reaction [5]) (Reaction [4]) « 1and therefore the aluminum activity for these compositions can be taken as equal to the square root of the activity ratios (i.e., aNi = 1). If equilibrium is estab-

Jan 1, 1968

By J. F. Martin, J. E. Friedline, L. M. Melnick, G. E. Pellissier

A method has been developed for determining gases in steel in which the gases are extracted by vacuum fusion and analyzed by mass spectrometry. This method is especially applicable for determining small amounts of oxygen and nitrogen. The lower limit of detection for both oxygen and nitrogen is 0.0001 pct with an average deviation of about 0.0001 pct for oxygen and 0.00008 pct for nitrogen. Hydrogen analyses by this method are in good agreement with analyses by vacuum tin-fusion. A complete analysis of all gases extracted from a steel sample can be accomplished in 40 min. It has long been known that certain of the gaseous elements exert particular effects on the physical and mechanical properties of steel. With the recent advent of new experimental steelmaking practices it is now possible to obtain steels with extremely low contents of such elements as oxygen and nitrogen. Present methods for determining these two gases are of insufficient sensitivity as applied to steels made by these newer practices, and therefore a new technique was considered necessary. A review of the literature showed that the conventional vacuum-fusion method1 was the procedure most suitable for modification to obtain a sensitive method for determining the gaseous elements present in steel simultaneously. However, for trace amounts of gases it is impractical to increase the sample size because of the physical limitations of the apparatus and the increased degassing time which would be necessary. Also, when only one of the desired gases is present in trace amounts, quantitative separation by conventional vacuum fusion is almost impossible. Since small analytical mass spectrometers are now commercially available, it was decided to use this instrument in conjunction with conventional vacuum fusion for both qualitative examination and quantitative determinations of the gaseous elements in steel. This technique has already been used with success for the analysis of copper and lanthanum.2"4 APPARATUS A vacuum-fusion unit was first designed and built, Fig. 1. This unit was designed especially for the determination of small amounts of nitrogen and/or oxygen in steel since an acceptable method (vacuum tin-fusion)5 was already in use for the determination of hydrogen in steel. The vacuum system was con- structed of Pyrex glass throughout. Mercury check valves were used in place of stopcocks in the high-vacuum section of the system. Ferromagnetic samples are normally introduced into the vacuum system through a mercury lift. In case of a break in the lift, the mercury is prevented from entering the furnace by a self-locking, mercury safety check valve, Fig. 2. This check valve, developed at our laboratory, is a modified T/S ball-and-socket joint placed in the sample inlet system between the mercury and the furnace. A sudden entry of mercury or air pushes this valve into the closed position, completely blocking the top of the mercury lift. The check valve is held in the closed position by the vacuum of the apparatus. A separate entrance tube also was placed in the system, so that samples which would amalgamate with mercury, or which are nonmagnetic, could be introduced into the furnace. A slightly modified Guldner-Beach furnace is used in this system.8 The optical flat was connected to the system by a ground-glass joint to facilitate cleaning, a quartz delivery tube was substituted for Pyrex, and the crucible was used uncovered. Fusion takes place in a high-purity graphite crucible insulated by — 200-mesh high-purity graphite powder. The crucible set (crucible and funnel) is suspended in a quartz crucible. The furnace envelope and the sample inlet system are exhausted by 2 single-stage, mercury-diffusion pumps in series. The first of these is a high-speed pump, which will work only with a very low backing pressure. This pump is used to exhaust the gases from the furnace as rapidly as possible. The second mercury-diffusion pump is used as a backing pump for the first; the capacity of this pump is much lower. However, it will work efficiently against a back pressure of 3 mm of mercury. To assure positive pumping, a modified Naughton and Uhlig condenser7 is used. With the use of proper valving the second pump is also used as a circulation pump in the catalyst system.

Jan 1, 1959

By C. Gatlin, N. E. Garner, A. Podio

Experimental data from single chisel blows on Leuders limestone are presented. A pressure chamber, similar in design to well known microbit drilling chambers, was utilized to impose variorcs stress states on the sample. Confining pressure of zero to 10,000 psi and borehole pressures from zero to 5,000 psi have been used in the studies. Pore pressure was zero and the rock samples dry in all instances. Force-displacement records and visual examination of the craters indicate that the mode of failure depends on both confining and borehole pressure in certain ranges, ranging from brittle, through a transition, to near plastic. The mode of failure is reflected in the observed blow force and energy data, as well as the shape of force-penetration curves. INTRODUCTION A previous paper&apos; presented initial data from the project on which this paper is the second report. While the first paper dealt with impact studies on synthetic rocks, the literature cited there is also pertinent to this paper, but will not be listed again in order to avoid needless repetition. This paper presents experimental data from single chisel impacts on limestone at certain simulated wellbore stress states. Specific variables investigated were combinations of borehole and confining pressure, crater geometry, a narrow range of impact velocity and the forces required to drive the chisel into the specimens under the varying conditions. EXPERIMENTAL PROCEDURE The same basic apparatus described in our earlier paper, except for the pressure vessel, was used in this study. Fig. 1 shows the complete experimental system. Fig. 2 shows details of the pressure cell, which is quite similar to the well known microbit drilling chamber. The confining (overburden) pressure system provides independent pressure control over the sample except for two, 21/4 in. diameter areas located on the sample ends. These two areas provide a pore pressure entrance on the bottom and a striking surface on the top where borehole pressure can be controlled. The ends are isolated from the confining pressure by O-ring seals. The borehole and pore pressures are related through the striking surface; they will be the same unless a seal is deposited on the borehole surface, either a mud cake or some other impermeable membrane. In these studies pore pressure control was not used, as the rocks were dry and unsaturated in all cases. Rock samples were prepared from 4-in. cubes as illustrated by Fig. 3. The circular disks of adhesive vinyl plastic protected the impact surface from the resin coating (Scotchcast No. 2) and were removed just prior to each test. This procedure insured a fresh uncontaminated surface for the impact. Fig. 4 shows the dimensions and loading of the sample, including the concentrations around the "borehole" periphery (O-ring seal). The rock used in this study was Leuders limestone, of Permian age (Leonard), quarried near Leuders, Tex. Geologically, Leuders limestone is a light gray, fossili-ferous limestone (oolitic foraminifera1 biosporite). Its fossil content is 80 to 90 per cent and consists primarily of calcitornellid, ostracods, pelecypods and oolites with the remaining part intraclasts. There are hematite or limo-nite rims on some of the intraclasts. The porosity is approximately 20 per cent, but the permeability is less than 1 md. There is no apparent orientation in the structure. Triaxial tests have been conducted to determine the variation of the physical properties of Leuders limestone in three orthogonal directions&apos;, and it is known to be unusually isotropic and uniform. Physical parameters for this rock are: uniaxial compressive strength = 9,700 psi; F = 32 and C = 2,700 psi; where + and C are Coulomb equation values (t = C+u tan +). Impact tests were run under the combinations of confining and borehole pressures shown in Table 1. Samples were dry with atmospheric pore pressure in all cases. Tests, in which elevated borehole pressures were applied, used a single layer of household Saran-Wrap to prevent horehole fluid invasion into the sample. This proved to be simple and reliable. The blunt wedge used in all the tests was 0.75 in. long and had an included angle of 60" with a 0.05-in. flat. In addition, a sharp 60" wedge was used for all confining pressures at zero borehole pressure. The chipper speed

By J. Chipman, N. J. Grant, H. L. Bishop, H. N. Lander

Data of several studies on the equilibrium between molten iron and open hearth-type slags have been combined to determine some of the chemical reactions involved in steel-making. Effects of slag composition and temperature on the iron oxide activity, distribution of sulfur between slag and metal, and the carbon content of the metal are discussed. Also, an overall reaction for the equilibrium between sulfur and oxygen is presented. DURING the past 15 years, a number of significant equilibrium studies have been carried out between liquid iron and simple basic and acid slags in an effort to throw light on the chemical reactions involved in steelmaking. This paper is a summary of the experimental reports on investigations which have been conducted at the Massachusetts Institute of Technology, and of related work in other laboratories. The investigations summarized in this paper include the works of Fetters and Chipman1 and Taylor and Chipman,&apos; which dealt with simple slags that are similar to those found in the open hearth. The sulfur determinations of the slag-metal tests of Fetters and Chipman as reported by Grant and Chip-man" are included. Also, the investigations by Win-kler and Chipman&apos; and Grant and ChipmanQ f more complex slag systems are included in this summary. The experimental procedure is described in detail in each of these papers and will not be discussed. Since the previous reports have been somewhat independent, it is desirable to review and combine the data of the various investigations to determine, as accurately as possible, the reactions in the slag-metal systems of the open hearth. It is the object of this report to present the combined data in such a way as to enhance their utility and applicability. Oxidizing Power of Slags of the System (CaO+MgO)-Si0,-FeO in Equilibrium with Carbon-Free lron The slags selected to determine the iron oxide activity in equilibrium with pure liquid iron were those containing less than 2 pct each of P,O,, MnO, or A1,0, on a weight percentage basis. The method used to calculate activities of iron oxide in liquid slags was that developed by Taylor and Chipman.&apos; The solubility of oxygen in molten carbon-free iron under pure iron oxide slags can be expressed by the following eauation —6320 log (pctO)-------------— + 2.734 [1] where T is the absolute temperature. The oxygen solubility values as determined from Eq. 1 were used throughout this study to calculate the iron oxide activity. The iron oxide activities of slags of various iron oxide contents are plotted in Fig. 1 as a function of the basicity, which is defined as the ratio (pct CaO + pct MgO)/pct SiO,, and are based on molecular percentage values of the components. The percent (FeO), is the total iron content in the slag calculated to FeO. Fig. 1 shows that as the basicity increases at constant mol pct (FeO),, the iron oxide activity increases rapidly and reaches a plateau which extends on the basicity scale from about 1.3 to 2.3; the iron oxide activity then decreases rapidly until a basicity of about 3.0 is reached, where it tends to level off. The solid portions of the curves represent the experimental data of Fetters and Chipman and Win-kler and Chipman. Their experimental heats were made in magnesia crucibles, and hence the slags were saturated with magnesia. The broken lines on the left represent the experimental data of Taylor and Chipman, who used a rotating crucible. In general, these slags contained less than 3 pct MgO. The absence of data for slags containing less than about 40 mol pct (FeO), and basicity ratios greater than about 2.5 made it necessary to calculate curves using ionic concepts of slags. The broken lines on the right, which disregard the solubility limits of di and tricalcium silicate and lime, were obtained by following the treatment of Flood and Grjotheim,"

Jan 1, 1957

By D. T. Peters, J. C. Bisseliches, J. W. Spretnak

The pain boundary relaxation phenomenon in high-purity copper, 0FHC copper, and a precipitation-hardenable alloy o-fCu-2 uit pct Co has been studied by internal ,friction and elastic aftereffect techniques. The data were analyzed by assuming the broad distribution of relaxation times observed obeys a lognormal distribution law which enables calculation of the relaxation strength. Grain size had no effect on relaxation strength, although the peak width increased with increasing grain size and decreasing temperature. A double grain boundary peak was produced in high-purity copper by annealing to produce secondary recrystallization. The activation energy measured for 99.999 pct Cu is 37.5 * 3 kcal per mol and 46.5 kcal per mole for OFHC copper. A small peak in the Cu-Co alloy at about 220°C at 1 cps was deduced to be the grain boundary peak. Its height increased and its activation energy decreased with increasing aging time. Except for erratic peak positions the observations were consistent with the theory of pain boundary sliding. BEFORE the mechanism of the grain boundary internal friction peak in metals can be satisfactorily explained, the detailed characteristics of the relaxation process must be documented. Of interest are the effect of grain size on relaxation strength, the high-temperature background, and peak width and position. The effect on the grain boundary peak of a precipitate at grain boundaries and of the change in distribution of the particles with aging time must also be explained by any existing or forthcoming theory. The model which has received the most attention was proposed by KG&apos; and zener2 and proposes that the anelastic strain results from sliding of adjacent crystals at grain boundaries. The sliding is limited by the interlocking of grain corners. It follows, according to this model, that the relaxation strength is independent of and the relaxation time is proportional to the grain size. The proportionality between grain size, D, and relaxation time, t, has been confirmed by K&&apos; and Bisseliches . In this case, the internal-friction peaks of various specimens can be superimposed by plotting Q-&apos; as a function of the parameter vD exp H/RT where v is the frequency and H the activation energy. However, the data of Starr et 01.&apos; and Leak6 fit better to a parameter containing D to an exponent near two. A meaningful relationship is not always deducible from the shift of peak temperature with grain size. KG7 demonstrated that a twofold variation in grain size obtained by varying the amount of cold work followed by identical recrystallization anneals will cause a peak shift that is too large to be accounted for even by an exponent of two. Since the decreased grain boundary area existing with a larger grain size is exactly compensated for by an increased sliding distance, the relaxation strength should not decrease with increasing grain size. The height of the internal-friction peak has generally been observed to be rather insensitive to grain size as long as the average grain diameter does not approach the specimen diameter. Exceptions have been reported by Koster, Bangert, and Lang8 for copper, and by Leak6 for iron. The observations for copper could well have been confused by the presence df 0.3 pct0. The possibility that the peaks may simply be increasing in width with increasing grain size and that the relaxation strength, which is proportional to the area under the peak, may remain constant was not examined. his point has been checked in this investigation using high-purity copper. Atomic mechanisms to account for damping by sliding at grain boundaries have been proposed by KG7 and Mott. KG predicts the activation energy to be identical to that for self-diffusion. Mott&apos;s "island" model suggests the activation energy is nL where n is the number of atoms in an island and L is the latent heat of fusion per atom. Other authors have felt that a value equal to the activa-

Jan 1, 1964

By J. W. Goss, M. J. Coolbaugh

Most grouting has been done to stop water flaw in mines and for stabilizing foundations of various man-made structures, a survey of the U.S. literature reveals. Apparently Sun Manuel is one of the first mines in this country to use grout extensively underground for strengthening and stabilizing ground in drifts, shafts, and stations. A comparison with other procedures as well as details of the Sun Manuel program are covered. The employment of pressure grouting as a ground stabilizer at the San Manuel Copper Corp. mine reduces delays in both development and production, lowers costs, and makes possible safer working conditions. It specifically reduces delays in haulage operations and permits the maintenance of normal ventilation. In development work this grouting allows faster excavation by cementing together highly fractured or broken ground that otherwise would require extensive cribbing or spiling. In drift repair, it consolidates the loose or fractured rock over the timber or steel drift supports, thus decreasing the frequency of repair, lessening the hazards from falling rock, and curtailing delays due to blockage of drifts by muckpiles and repair operations. Pressure grouting is the process of pumping an accurately controlled mixture of cement and water into loose, fractured, or porous rock. The ratio of water to cement varies according to the nature of the rock encountered, from the thinnest mixture of 30 gal of water per sack of cement, used to fill very fine fissures, to very thick grout of 5 gal of water per sack of cement, used to fill large fissures or extensive areas of loose, broken rock. The pumping pressures at San Manuel vary from about 100 to 1000 psi, depending upon the compactness of the rock, while at other mines the pressures sometimes go as high as 5000 psi. In order to grout an area in which ground water is encountered, the pumping pressure of the grout must be increased by an amount equal to the pressure of the ground water. GROUTING IN DEVELOPMENT WORK The areas under development at San Manuel include many sections of loose, highly fractured rock. Prior to the advent of the grouting program, drifts, shafts, and stations in these areas could not be excavated without utilizing extensive support such as cribbing, spiling, and breast boarding. This slowed down the development work and increased the costs considerably over that required for excavating in more competent ground. Now, when a particularly bad area is contacted, the mining is temporarily stopped while the bad portion of drift or shaft is grouted. After the grouting is completed, the excavating is resumed with an approximate decrease of 50 pct in lost time and costs. Grouting in Drifts and Turnouts: The grouting procedures and patterns used in drifts and turnouts are very similar. The standard procedure for grouting such a turnout is shown in Fig. 1. After the ground is supported as well as possible with cribbing or lagging, the gaps between the back lagging and side lagging are plugged with empty cement sacks or additional timber, if necessary. The ground surrounding the proposed turnout is then grouted in two stages. In the first stage, the broken and caved rock is drilled and grouted to a depth of 5 to 10 ft, depending on the depth of the broken rock. This stage forms a grouted seal that allows higher pressures to be used at depths beyond 10 ft without developing excessive leaks at the face. After a grout hole is drilled, a 10-ft long pipe is wedged tightly into it with empty cement sacks. Grout is then pumped into the hole until the pressure reaches 200 to 300 psi, and the pipe is subsequently removed if it hasn&apos;t become cemented in. No more than one hole at a time is drilled and grouted because the grout has a tendency to go from one hole into another, plugging up the latter. Five or six holes are usually adequate for the first 10 ft of grouting. Experience has shown bentonite to be a useful admixture to the grout, particularly when it is indicated that the grout is being lost into large fissures or voids. Bentonite increases the plasticity of the grout enabling it to remain in place more easily until it has begun to set. In the second stage, the longer holes are drilled through the previously grouted rock, after which the

Jan 1, 1961

By Claude P. Heiner

W-hile the litle of this paper embraces the entire West Coast, the author, in the interest of simplification, has confined the discussion to California—particularly the central section. California&apos;s population has risen 45 pct since 1940. Its electric requirements have also increased, not only because of the growth in industry and population but also because of the widespread tendency of all types of electric consumers to use more electricity than ever before. The growth of California&apos;s electric utilities is shown by published data covering operations of three of its large systems and is given in Table 1. New Capacity Steam Driven In meeting these additional electric loads there has been a substantial increase in generation from fuel burning plants as shown by the published energy statistics given in Table 2. Increased Fuel Oil Consumption A study of construction plans of the three electric utility systems named in Table 2 clearly shows that expected new electric loads are to be met, to a large extent, by new steam generating capacity as shown by Table 3. D. D. Smalley, Vice President of the Pacific Gas and Electric Co., in an address before the Pacific Coast Electrical Association in June 1948, stated that California utilities plan to meet new electric loads through greater use of steal11 plank and that in 1951 approximately 45 pct of the area&apos;s electric production would be by steam as compared to 33.6 pct in 1946. He stated that if load growth develops as expected and if the year 1952 is dry, thereby requiring high load factor steam operation, the Pacific Gas and Electric Co. would need the equivalent of nearly 25 million barrels of fuel oil. Federal Power Commission reports show that the energy input to the Pacific Gas and Electric Co. system was approximately one billion kilowatt-hours greater in 1947 than in 1946. They also show that the steam plant operating capacity factor in 1946 was approximately 35 pct; in 1947 it, was 72 pct due, probably, to the extreme drought. able 3 shows that Pacific Gas and Electric Co. now has under construction 327,000 kw of hydro capacity which, by 1950, will bring its total hydro generating capacity to 1,313,899 kw. In addition to hydro capacity under construction that company also has 975,000 kw of steam generating capacity under construction, which by 1951 will bring its total steam capacity to 1,560,834 kw. If it is assumed that this total steam electric capacity is operated at a capacity factor of 45 pct, in 1951, over 6 billion kilowatt-hours would be generated. If the load growth on the Pacific Gas and Electric system continues at the current rate of approximately one billion kilowatt-hours per year and if it is assumed that 70 pct of this increase would be generated by steam (30 pct assumed to be generated by hydro facilities with average water conditions), the steam electric production in 1960 would amount to 12 billion kilowatt-hours, which would require fuel the equivalent of 24 million barrels of oil or 6 million tons of coal. Government Projects Inadequate Much has been written with respecl to the plans of the Department of Interior in regard to the installation of hydroelectric plants as a part of multipurpose dams relating to reclamation. flood control, and power generation. An examination of the effect of such plans on the power supply for central and northern California is of interest. The Depart,ment of Interior now has five 73,000 kw units at its Shasta hydro plant on the Sacramento River. It now appears that its three 25,000 kw unit Keswick hydro plant on the same river will be available during the winter of 1949 to 1950. Its estimates show that in a dry year there is sufficient water for operation of Shasta units at an average load factor of 36 pct and Keswick units at a load factor of 41 pct. It is also giving consideration to the development of the Pine Flat and Haas hydroelectric plants on Kings River for generating capacities of 45,000 kw each. The total installation of Government, units in Central Valley and Kings River in California is relat.ively small when compared with t.he

Jan 1, 1950