Search Documents

By W. G. Bearden, P. P. Scott, G. C. Howard

This paper concerns the rupture or breakdown of rock formations as related to drilling, completing, and stimulating production of wells, and comprises data compiled from a study of literature and records of treatment of oil and gas wells. and from tests conducted in bores drilled into rock cores and outcrops of rock. Results of the investigation indicate that the internal pressure to rupture cylinders of rock and to breakdown rock formations surrounding a bore in the earth is dependent upon the extent of intrusion of fluids. the position of bedding planes. the ratio of internal to external diameter, the tensile strength of rock, and magnitude of confining pressure, and is independent of the size of bore, degree of fluid saturation. and temperature of rock within practical limits. It is concluded that the mathematical relationship of pressure in bores and stresses in the surrounding rock must not be limited by the simplifying assumptions of homogeneity. isotropy, and impermeability; that the incidence of lost circulation of drilling fluids to induced fractures may be reduced by preventing intrusion of fluids into the small intrinsic fractures along weak bedding planes; and that the magnitude of the breakdown pressure of wells to be treated may be lowered by removal of mud cake. INTRODUCTION The purpose of this paper is to present and discuss the results of tests which may serve to broaden the understanding of the phenomena of rupture or breakdown of rock and thus contribute to the improvement of the techniques for drilling and completing wells. including such operations as preventing lost circulation, stimulating production, and placing cement. Since the early recognition of the possibility of rupturing rock adjacent to a well by fluid pressure, the distribution and magnitude of stresses around a well and the internal pressure to cause failure have been expressed mathematically by application of the principles defining the elastic and inelastic behavior of thick-walled cylinders of a homogeneous. isotropic, impermeable material. In either the elastic or plastic state, if the conditions of homogeneity. isotropy, and impermeability were the normal characteristics of rock. there would be no reason to question the validity of the above principles when applied to rock. However. since most rock formations are characteristically permeable to some degree, contain bedding planes and small intrinsic fractures. and are heterogeneous, rendering invalid the assumptions of homogeneity, isotropy, and impermeability, the application of the thick-walled cylinder theories to the behavior of rock formations penetrated by a bore appears illogical. Also the failure to consider the effect of the properties of the drilling fluids, which certainly intrude in various degrees into most rock formations. is further cause for questioning the application of these principles. Even in the case of cylinders of hardened chrome-nickel steel, which would he considered relatively homogeneous isotropic. and impermeable, as compared to rock, it has been observed that the internal pressure capable of being withstood by the cylinders varied with the sizes of molecules comprising the rupturing fluid used. Because of these apparent weaknesses in the theories of the behavior of thick-walled cylinders when applied to bores in rock, and the importance of knowing the true behavior of rock under the influence of fluid pressure when planning drilling and completing procedures for wells, tests were undertaken to determine by observation the actual rupturing pressure of cylinders of rock and the effects of such variables as environmental conditions and characteristics of rock formations, fluid properties, and bore dimensions. It was intended that by these tests the validity of the thick-walled cylinder theories when applied to rock would be determined and, if found invalid, mathematical expressions would be derived for predicting stress and rupturing pressure of rock formations under various conditions. Since the derivation of mathematical expressions has been only partially completed, all of the results of the latter phase are not included in this paper. PROCEDURE The investigation was initialed with a study of the theories pertaining to the rupturing of thick-walled cylinders of homogeneous. isotropic, impermeable material and a study of the

Jan 1, 1953

By Albert J. Phillip

Jan 1, 1947

By Albert J. Phillip

Jan 1, 1947

Jan 1, 1897

By William E. Ford, Edward Salisbury Dana

The NATIVE ELEMENTS are divided into the two distinct sections of the Metals and the Non-metals, and these are connected by the transition class of the Semi-metals. The distinction between them as regards physical characters and chemical relations has already been given (Art. 453). The only non-metals present among minerals are carbon, sulphur, and selenium; the last, in one of its allotropic forms, is closely related to the semi-metal tellurium. The native semi-metals form a distinct group by themselves, since all crystallize in the rhombohedra1 class of the hexagonal system with a fundamental angle differing only a few degrees from 90°, as shown in the following list :

Jan 1, 1922

By C. van Dijk

In Sept., 1960, a steam-drive project was started in the solution-gas drive area of the Schoonebeek field. A part(ern of three five-spots and one four-spot was selected covering an area of 65 acres. The pay in the project area has good lateral continuity and dips slightly to the northeut; it is about SO ft thick and permeability increases from 1,000 and at the bottom to approximately 10,000 md at the top. The oil originally in place was 12.6 X 10' bbl. The oil has an in situ viscosity of about 180 cp. At the start of the steam drive the cumulative primary production due to. solution-ga.7 drive amounted id 4 Percent of the oil originally in place. Reservoir pressure had dropped about 120 psi and no significant primary re-.serves remained. Some 11.3 million bbl of steam (all steam quantities are expressed in barrels of water vaporized) have been injected, resulting in production of an additional 4.1 X I0 9bl of oil, or 33 percent of the oil originally in place. This corresponds to a cumulative oil-stearn rario of 0.37 bbllbbl. It appears that the steam preferentially moves r updip while liquids are produced mainly from downdip wells observations indicate that tile steam flows through only the upper part of the formation. The lateral steam distribution in the pattern is satisfacrory since several prodriction wells hardly reacted and, hence, cori tributcd little to the oil production. Production performance and results from material balance calcutlations agree satisfactorily with the results of large-,scale laboratory experiments. On the basis of these experirmental results the .steam drive, together with a cold water follow-up. is expected to bring ultimate recovery to a value of crt leas: 50 percent of the oil originally in place. No serious production problems have been encountered. However, due to mechanical fuilure, two old prodriction wells and one injection well had to be replaced. An extension of the. steam drive in this area is under connstruction. Introduction The Schoonebeek oil field, discovered in 1943 and developed after World War 11, is situated in the eastern part of the Netherlands. The main oil reservoir in this field is the Valanginian sand. A completely sealing fault divides this reservoir into two areas (Fig. 1): the southwestern part of the sand body where primary production is ob- tained by means of a solution-gas drive, and the remain. der where edge-water drive is the production mechanism. In the greater part of the field the reservoir consists of a single, unconsolidated sand body. The net thickness ranges from 30 to 100 ft and the top is between 2,400 and 2,800 ft below sea level. Formation permeability varies from approximately 10,000 md at the top to values of the order of 1,000 md at the bottom, and porosity is about 30 percent. The reservoir contains a paraffinic oil of 25" API gravity with an in situ viscosity of 160 to 180 cp. Initial oil saturation was high (85 to 90 percent). The relatively large quantity of oil in place (more than 10' bbl), and the low ultimate primary recoveries expected from this field — approximately 15 percent stock-tank oil initially in place (STOIIP) for the water-drive area and 5 percent STOIIP for the solution-gas drive area — clearly indicate ample scope for secondary recovery. Because ies-ervoir and crude characteristics made this field suitable for thermal secondary recovery, a hot-water drive project was started in the water-drive area about 10 years ago. A few years later a steam drive and an in situ combustion project were started in the solution-gas drive area. This paper deals with the performance of the steam-drive project, which was started in Sept., 1960, and which is still in operation. Design of Steam-Drive Project, An experimental investigation of the steam-drive process carried out by schenk in 19561 indicated that under schoonebeek conditions steam injection could be an attractive secondary recovery method. the findings and encouraging results of a pilot test in the Mene Grande field in venezuela,i led to the design of a steam-drive project in the schoonebeek field, Pruject Site and Pattern In 1958 the reservoir pressure in the solution-gas drive area had decreased to about 120 psi, and oil production rates of wells in this area had dropped to 7 to 10 B/D. The cumulative primary production was about 4 percent STOIIP, leaving an oil saturation of approximately 85 percent. In view of the large amount of oil left behind in the reservoir, the solution-gas drive area was selected for the planned steam-drive project. The area in the vicinity of Well S1 3 (Fig. 2) was considered to be suitable since it is at least partly isolated from the rest of the field by faults and the sand is relatively thick (about 80 ft).

Jan 1, 1969

By Robert K. Steunenberg, Irving Johnson, James B. Knighton

The activity coefficient of plutonium in liquid magnesium, over the temperature range 650° to 800°C, was obtained from measurements of the distribution of plutoninm between a 50 mole pct MgC12-30 mole pct NaCl-20 mole pct KC1 molten-salt mixture and liquid Zn-Mg alloys. For dilute solutions (0.08 at. pct Pu) the activity coefficient of plutonium was found to vary from 10.1 at 650°C to 12.2 at 800°C. The activity coefficients of plutonium in dilute liquid solutions of plutonium in uranium, silver, lanthanum. cerium, and calcium were estimated to be. The distribution data indicate a value of about 0.1 at 800°C for the activity coefficient of PuCl3 dissolved in the above ternary salt mixture. LIQUID magnesium and several liquid alloys of magnesium with metals such as zinc and cadmium have been shown to be useful solvents in pyrochemical processes for the recovery of uranium and plutonium from discharged nuclear fuels,' and for the separation of transuranium elements.' The present study was undertaken to determine the activity coefficient of plutonium in liquid Pu-Mg alloys in support of process-development work. The activity coefficient of plutonium in liquid magnesium was determined from experimental data on the distribution of plutonium between a liquid ternary MgC12-NaC1-KC1 salt mixture and various liquid Zn-Mg alloys. The distribution data were used to calculate the ratio of the activity coefficients of plutonium in liquid zinc and in liquid magnesium. The activity coefficient of plutonium in liquid magnesium was then computed from the known activity coefficient of plutonium in liquid zinc. It was not necessary to know the thermodynamic properties of the molten-salt system explicitly. The major features of the Pu-Mg system have been reported by Schonfeld.3 At the temperatures of interest in the present study, i.e., above about 600°C, the phase diagram indicates the existence of a wide liquid-miscibility gap, with the plutonium-rich liquid containing about 8 at. pct Mg and the magnesium-rich liquid containing about 10 at. pct Pu at the intersection with the solidus regions. Additional data on the compositions of the two equilibrium liquid phases obtained in this laboratory4 have defined the miscibility gap up to the consolute temperature (at about 1040°C). EXPERIMENTAL PROCEDURE AND RESULTS Materials. The 50 mole pct MgC12-30 mole pct NaC1-20 mole pct KC1 salt mixture was prepared by melting the required proportions of reagent-grade NaCl and KC1 with anhydrous MgC12. The molten salt was then purified by contacting it with liquid Cd-30 wt pct Mg alloy (at 450°C) to reduce oxidizing impurities, followed by filtration through a stainless-steel frit (pore size, 65 µ) to remove solid MgO formed during the reduction. The purity specifications of the zinc, magnesium, and plutonium were 99.999, 99.8, and 99.85 pct, respectively. Apparatus. The liquid salt and metal were contained in a tantalum crucible inside a graphite secondary vessel. The crucible assembly was located inside a resistance-heated stainless-steel furnace tube. The furnace tube was closed by means of a stainless-steel cover, which was attached by bolts, with a neoprene O-ring serving as a gas-tight seal. The top of the furnace tube was water-cooled to protect the O-ring. The furnace-tube cover was provided with a tantalum thermowell, a tantalum stirrer, and a port through which sampling tubes could be inserted and materials could be added to the melt without admitting air to the furnace tube. Vacuum and an argon atmosphere were available through a side-arm on the furnace tube. The furnace temperature was regulated by a proportional controller that was actuated by a chromel-alumel thermocouple between the furnace tube and the heating elements of the furnace. The melt temperature was measured by means of a chromel-alumel thermocouple in the tantalum thermowell. The accuracy of temperature measurement was ±3°C. The salt and metal phases were intermixed by a motor-driven tantalum paddle positioned at the liquid interface. The tantalum crucible was provided with four baffles to increase the turbulence. The sampling tubes consisted of 1/4-in.-OD tantalum tubing that terminated in a tantalum frit (Kawecki Chemical Co.; average pore size, 30 µ). Procedure. The zinc, magnesium, plutonium, and salt were charged to the tantalum crucible; then the system was evacuated and filled with argon. The melt was brought to the desired temperature, and agitated for 1 to 2 hr. After allowing the salt and metal to separate, both phases were sampled. Filtered samples were obtained by immersing the end of the sampling tube in the liquid and increasing the argon pressure sufficiently to force the liquid salt or metal through the frit into the tantalum tube. The sample was then partially withdrawn into the cooler portion of the furnace tube and permitted to solidify before being removed. The temperature sequence for sampling at each magnesium concentration was 800°, 700°, 600°, 650°, and 750°C. The composition of the liquid-metal phase was varied by incremental additions of magnesium in a series of experiments at low magnesium

Jan 1, 1967

By Roland Blanchard

ABSTRACT RECENT discovery at Mount Isa of copper mineralization in commercial amount at a depth of 1000 ft., coinciding with downward termination of ore at about the same depth within the larger silver-lead-zinc lenses that have been the standby of Mount Isa's production to date, has been cited as an example in support of mineral zoning. A previous paper by the author and Graham Hall1 furnished a detailed description of the geology of the ore at Mount Isa as exposed up to that time, but necessarily dealt mainly with the silver-lead-zinc mineralization. Most of the geologic facts that constitute the first half of the present paper were set forth in the previous one in much greater detail, with full supporting evidence for the facts cited. The large amount of underground development (approximately 20 miles) and the extensive exploration carried out by diamond drilling (100,000 ft.) at Mount Isa, added to extensive microscope work conducted over a period of years, both by the company's staff and by others, had made possible the calculation within fairly close limits of mineralogical composition of the principal mineralized block of ground down to 1000-ft. depth, and had established closely the mineral succession, with reasons for deposition of the various minerals in the patterns now occupied by them. The geologic facts as outlined in the previous paper remain as stated; but because substantial development within the new copper ore body and further exploratory diamond drilling within the new silver-lead-zinc area (Race-course) have taken place since that paper was written, statements and figures relating to those two areas in the present paper supersede those furnished in the previous one. The recent work likewise has established more clearly the paragenetic relationship between the chalcopyrite and galena. Evidence confirming the relationship is furnished in the present paper. The facts of ore occurrence at Mount Isa show [ACCEPTED ZONAL SUCCESSION Silver sulphantimonides Galena Sphalerite Tetrahedrite Arsenical sulphides Chalcopyrite Pyrrhotite MOUNT ISA SUCCESSION Chalcopyrite In the main but Silver sulphantimonides wholly Tetrahedriteably not Galenacontemporaneous Pyrrhotite Sphalerite Arsenical sulphides They show further: (I) that instead of the silver-lead minerals yielding to increased zinc in depth, the zinc yields to increased silverlead; (2) no dovetailing of the silver-lead-zinc sulphides into chalcopyrite takes place; (3) despite the large amount of pyrrhotite deposited in the district (estimated at upward of 100,000,000 tons), its deposition took place under moderately low temperature conditions; (4) no evidence has been found for increase in temperature of deposition, with depth, to deepest exploration in ore (1495 ft.). The anomalous condition at Mount Isa, both as to the unorthodox mineral succession and the largely unorthodox pattern of mineral distribution, is explained in the present paper,

Jan 1, 1943

By Frank Doxey

AT Dominion Steel & Coal Corp. it has long been recognized that continued mechanization of mine operations is necessary in the Pictou, Cumberland, and Sidney coal fields of Nova Scotia. The varied physical conditions in these fields call for special consideration of individual cases before planning is finalized. Because standard equipment cannot be procured which would operate successfully, many experiments have been necessary over the years to keep pace with the progress made in other countries. There are two mines, producing 2000 tpd, located in the Pictou coal field. The field is badly distorted and crossed by many faults. Seams are highly inclined and irregular and vary in thickness from 5 to 40 ft. Entries are difficult to maintain because of squeezing of the coal. ribs and movement of the roof and pavement. Output from the three operating mines in the Cumberland field is 3000 tpd. The field is highly inclined, inclination varying from 12° to 32°. Overlying beds consist of shales and massive sandstone lenses of extreme toughness and are responsible for bumps when the stresses are relieved by extraction. At greatest depth these are among the deepest coal workings in the world. Depth of cover ranges from 2300 to 4000 ft. This prohibits room-and-pillar working and necessitates longwall operation. Working of contiguous seams concurrently to maintain output increases the already difficult conditions. The Sydney field, with a frontage of about 30 miles, is the most important of the Nova Scotia coal fields. With the exception of one small area it is now wholly submarine. Output is approximately 21,000 tpd. Seams are 21/2 to 8 ft thick, and cover in the areas varies from 600 to 2300 ft, with an average of 1500 ft from sea bottom to the top of the seam. The seams dip in a seaward direction, pitches ranging from 6" to 4.0". The shoreline is the last place of entry to the seams and distance from the bank to the working faces is generally over 3½ miles, in some cases as much as 6½ miles. Ventilation is a problem and requires the construction of large permanent airways. Getting and Loading Coal: In 1925, in view of heavy pressures exerted by thickness of cover overlying the seams, roadways and pillars of the room-and-pillar system being worked began to break up and coal was lost. It was decided that a change in the method of extraction in areas with heavy cover was necessary, and experiments were made with many short walls and longwalls varying between 90 and 250 ft. Trial and error proved that the best operating length was between 400 and 500 ft, delivering all coal to the dip, with roadways to the face following a level course. The change-over was gradual, and the technique of roof control developed with the system, so that falls to the face are now very infrequent. An advantage of longwall mining is that it yields 95 pct extraction, especially important in coal seams of high quality or in seams where faults or disturbances restrict the workable areas. This percentage of extraction is based on the fact that the longwall advancing system takes development faces where pitch permits instead of driving headings and leaving roadway pillars. This system yields high tonnage during development and limits loss in extraction to duff left during operations. Accompanying disadvantages, on the other hand, are the heavy construction cost of main roadways and the necessity of driving all new flank face roadways through the gob. If the main roadways are driven through the solid, and large enough pillars are left on each side for protection against flank face weights, then the width of solid coal is approximately 1700 ft. This represents 10.6 pct of the coal available, or 89.4 pct extraction of the whole. These pillars, however, are of such size that they provide a useful pillar drawing area as a final operation of the mine. It may be that although the seam cannot be generally mined by the room-and-pillar method, it can be adapted to

Jan 1, 1955

By James F. Kemp

In submitting an additional contribution to the discussion on ore-deposits in the recent volumes of the Transactions, it is my desire to adhere closely to matters of material importance as affecting the actual processes. Judging from the discussion by Professor Van Hise, and from one or two reviews or other articles by associates of his in geological work, the impression seems to prevail that, in so far as my paper* referred to his masterly essay, I was guilty of misconceptions regarding both the part attributed by him in it to the igneous rocks and the ubiquitous presence of the ground-water. I should regret extremely to be wanting in these particulars or to have misunderstood one for whose great services in this and other branches of geology no one has a higher esteem than myself. I have, however, in the most careful way, and with these points in mind, read his essay again, and, taking it as a whole, I cannot gain any different impression of relative magnitudes than the one first received. The importance of the igneous phenomena and the restrictive influence of the processes described by " cementation " in their effect upon the ground-water, as set forth in Professor Van Hise's "Discussion" (Trans., xxxi., 292), impress me as being in very marked contrast with the same things in his first essay. If the point seems to anyone of sufficient importance, it can easily be decided by reading the originals. My paper was the result of some years of observation, reading and reflection, and was meant to be an independent contribution, controversial only in some subordinate particulars. In depicting the drama of the deposition of ores, I cannot but feel that Professor Van Hise assigned to the chorus and the scene-shifters some characters which, it seems to me, should

Jan 1, 1903

By Ronald D. Irving

The object of the present paper is to give an outline account of the mineral resources of the State of Wisconsin, so far as they are now known, including both metallic ores and non-metallic useful mineral substances. Tl~e only previous publication making ally attempt at such an account is one of a popular nature, prepared by the writer for Snyder and Van Vechten7s Historicccl Atlas of Wisconsin, which was published at Milwaukee in 1878. The data upon which the statements of the following pages are based are chiefly from the

Jan 1, 1880

By Thomas H. Leggett

A number of papers on the use of electricity in mining operations have been presented at the Institute meetings recently, but only a very few of them have given particulars and details of the

Jan 1, 1895

Andrew Carnegie, America's best-known ironmaster and philanthropist, died at his home at Lenox, Mass., Monday, Aug. 11, after a three days' illness. A pioneer in the steel industry, he introduced into this .country the Bessemer process And formed the plans that have resulted in this country's supremacy in the steel markets of the world. Known throughout the world for his, gifts, he is also known to engineers as the donor of the home of their National Societies and as the founder of the Carnegie Institute of Technology, of Pittsburgh. For many years, also, he was an honorary member of the American Institute of Mining and Metallurgical Engineers, the American Society of Mechanical Engineers, and of the Engineers Club of New York. What he considered the secret, of his success is shown by the epitaph he wrote for himself, "Here lies a man who knew how to enlist in his service better men than himself." He was buried Thursday, Aug. 14, in Sleepy Hollow Cemetery, Tarry-town, N. Y., the funeral services being private, in accordance with his wish.

Jan 9, 1919

By Harold E. Rowen

Sintering is accomplished at a temperature of more than 2000°F. For the purpose of this discussion it will be defined as the art of burning a solid fuel with 90 to 95 pct ash content. Think of the problems of combustion involved in keeping a home furnace burning properly with 12 to 20 pct ash in the fuel and remember that the amount of fuel involved in the 5 to 10 pct combustion loss represented by the definition has to be just about right or nothing is going to happen. Our forefathers discovered that many ores containing metals csscntial to the steadily rising standards of living were associated with other minerals, sulfur and arsenic, for example, which had to be removed before ultimate refining. They did this by utilizing the solid fuels they had available-the sulfur or other readily combustible components- to create roasting heat.

Apr 1, 1956

By C. E. Julihn

Technology concerns the ways of doing things; mineral technology the ways of performing operations required for obtaining minerals from the earth and extracting their valuable constituents for man's use. At any particular time, technology is relatively fixed, as everyone tries to adopt the way of doing things that has proved most profitable; but improvements evolve from minor changes here and there, and occasion- ally entirely new methods are discovered. Technologic improvement thus characterizes any long-time view of the mineral industries. Its test lies always in reduction of costs; there is no other incentive for the adoption of new methods. Reduction in cost of producing metal from ore decreases, in turn, the amount of metal that must be obtained from ore in order to pay for its production. An advancing technology thus is characterized by utilization of ores of lower and lower grade. A very important result of this is an increase in the gross quantity of metal obtainable at any price level, since the earth's crust contains vast amounts of very low-grade ores and relatively insignificant amounts of very high-grade ores. Technologic advances have, therefore, been the means of rendering the metals both cheap and abundant. Though concern as to possible exhaustion of the world's ore deposits is warranted, it is conceivable that a transcendent technology of the future might supply metal requirements from what we

Jan 1, 1932

By Henry W. Edwards

Concrete is not a new, nor even a modern substance. Important structures built by the old Romans before the commencement of the Christian Era are to-day sound and solid— for example, the dome of the Pantheon in Rome, 142 ft. in diameter. I do not propose, therefore, to discuss the durability of the material, as in the mining and metallurgical business, structures, as a rule, are not calculated to endure for two thousand years. I do wish to urge, however, that much of the stone masonry around mines and smelters would have given better results if concrete had been used in place of stone. Concrete looks better; is stronger, cheaper, more durable, more quickly built, and above all requires no skilled labor, except that of the carpenter, who, like the poor, is always with us. Well proportioned concrete, that is to say, having well proportioned ingredients, may be safely relied upon to withstand a compressive or crushing strength of 50 tons per square foot. In most American cities, however, the building laws limit it to the absurdly low figure of 16 tons. This restriction is probably due to the political influence of the building-trades unions, which object strongly to its too free use, undoubtedly owing to its not requiring the services of skilled workmen. I hope to show that quite important construction work may be' undertaken without the aid of the gentleman with the trowel. In some of the isolated districts of the West and Southwest this is no mean advantage. The weight of good concrete, dry, is from 130 to 160 lb. per cubic foot. Ingredients of Concrete. Concrete is composed of four ingredients; viz., 1. Crushed Stone; 2. Sand; 3. Cement; and 4. Water.

Jan 1, 1905

By A. K. Mukherjee, John E. Dorn

The effects of strain rate and temperature on the critical resolved shear stress for (321)[111] slip were determined for the silver-rich CsCl type of intermetallic compound AgMg. The flow stress increased only slightly as the test temperature was first decreased below room temperature; a rapid increase in the flow stress was obtained with yet further decrease in temperature from about 250' to 4OK. The effect of both the temperature and strain rate on the flow stress over the low-temperature range could be rationalized satisfactorily in terms of the Peiwls mechanism when the deformation was controlled by rate of nucleation of pairs of kinks. IN spite of the well-documented interest of metallurgists and engineers concerning the mechanical behavior of intermediate phases and intermetallic compounds, very little definitive information is available on this important subject. As recently summarized by westbrook,1 only limited and modest progress has been made thus far in elucidating the details of the mechanism of plastic deformation for the intermetallic compounds; the available information largely concerns phenom-enological descriptions of empirical observations and experimental facts, principally with reference to poly crystalline aggregates. The present report on the elucidation of the rate-controlling mechanism for slip in the bcc structure of AgMg is part of the comprehensive program of a systematic investigation on the mechanical behavior of intermetallic compounds. The intermetallic compound AgMg has a CsCl type of lattice structureZ and is completely ordered up to its melting point of 820c3 This material was selected for our present investigation because of its simple crystal structure, moderate and congruent melting point, ordered structure persisting up to the melting point, and some solubilities of the constituent elements, which could be expected to help in the growing of single-crystal specimens. Whereas previous investigations on the properties of AgMg include hardness,*"6 slip systems,7 tensile flow stress of polycrystalline specimens,' and electrical resistivity,4 the current investigation will be directed principally at elucidating the rate-controlling dislocation mechanism responsible for slip in single crystals at low temperatures. It will be shown that the strain rate is consistent with a model involving the rate of nucleation of pairs of kinks by the Peierls mechanism for plastic deformation. EXPERIMENTAL TECHNIQUES Single-crystal specimens of the AgMg intermetallic compound were prepared and tested as follows: 1) A master alloy ingot of AgMg was produced by melting and chill casting the high-purity silver (99.995 wt pct) and high-purity magnesium (99.997 wt pct) in an induction furnace under a helium atmosphere. 2) Sections of the above-mentioned ingot were placed in a graphite mold containing a spherical cavity in which a single-crystal sphere of 1 in. diam was grown under helium by the Bridgman technique. 3) The operative slip systems were investigated at room temperature on a singlecrystal of AgMg, from measurements of the angles made by the slip traces on the two surfaces of the specimen, which were at 90 deg to each other. The investigation confirmed that the AgMg compound undergoes slip primarily in the (321) plane and in the [Ill] direction, but a small amount of secondary slip was also noticed in the (112) (111) system. No slip was observed in the (110) planes. 4) The single-crystal sphere, mentioned earlier, was oriented in a graphite mold containing a cylindrical cavity of 3/8 in. diam above the spherical receptable to give the angle xo = 45 deg between the axis of the cylindrical bar and the normal to the slip plane (321), and the angle AO = 45 deg between the slip direction [Ill] and the axis of the bar. Oriented single-crystal bar seeds were produced by melting, under a helium atmosphere, a polycrystalline bar in the cylindrical cavity above the oriented spherical seed and by growing an oriented single-crystal bar from the seed. 5) Finally, oriented single-crystal specimens were grown from these cylindrical seeds. 6) The cylindrical specimens were machined in a High-Tension Spark Cutting unit to give a 2-in. gage length. The spark-machined gage section was elec-tropolished in a bath containing 200 ml of H3PO4,

Jan 1, 1964

By C. S. Smith, W. M. Williams

THE quantitative study of grain shape in three dimensions has been a difficult one from the practical standpoint. Experiments on grain shape have usually been based on indirect observations of two-dimensional metallographic samples or on grains separated by intergranular corrosion or fracture. The latter method was used in particular by Deschl in 1919 in observing the shapes of ß-brass grains which had been separated with mercury. The similarity in detail of shape and packing that exists between bubbles in a soap froth and metal grains was noted by Desch who remarks that: "Surface tension has an. important share in determining the form of the crystal grains in a solidifying metal and such grains have a tendency to assume the shape of foam cells." More recently the relation between grain shape and grain growth has been studied by Harker and Parker.' The importance of surface tension forces in determining microstructure has been discussed by Smith," and an analysis of the topologi-cal rules that apply to such structures has been made by the same author.' Biologists have made valuable contributions to the general problem of shape and form in an assembly of space-filling cells subject to surface tension forces. Particular mention must be made of the extensive researches of Lewis5,8 on botanical and anatomical tissues, and Matzke and Nestler,7,8 who have made painstaking studies of bubble shapes in different kinds of foam. The present paper introduces a new method of studying individual grains in particular alloys—a method which may well find use in other metallurgical researches, and which seems also to be applicable in biological problems. Metal Grains in Three Dimensions The individual grains in a piece of metal or the bubbles in a soap froth must satisfy two conditions —they must be in juxtaposition so as to fill space and their interfaces must conform to the laws of surface tension. If a further restriction is imposed, namely, that only one type of polyhedron be used, then the sole possibility is an assembly of "minimal" tetrakaidecahedra," each polyhedron having eight doubly-curved hexagonal faces and six plane quadrilateral faces, the angles between adjacent faces being 120". Such cells could be stacked on a body-centered cubic lattice and would be quite stable. For many years it was believed that soap bubbles actually possessed the shape of this ideal body, and the hypothesis was the starting point for several investigations on the shapes of soap bubbles, biological cells, and metal grains. These investigations have shown, what might have been obvious in the beginning, that if the condition of symmetry is relaxed the tetrakaidecahedron is almost never found. If we retain only the rule that all contacts should be in local surface tension equilibrium and that the assembly should fill space, metal grains may then take a nearly infinite variety of shapes and no single one may be regarded as an archetype. These two conditions, which are fully discussed in one of the previously mentioned papers,' lead us to think of a typical grain in an annealed metal as having the following characteristics: 1—A grain may have any number of faces, but usually between nine and eighteen. The faces (each of which is, of course, shared by two grains in the assembly) may have any number of edges, but usually between four and six. Pentagons are by far the most frequent. 2—In the assembly of grains each edge is shared by three faces and by three grains. Each vertex is a point shared by four grains, six faces, and four

Jan 1, 1953

By J. H. M. Thomeer

A method is presented that provides a mathematical description of capillary pressure curves and, probably, of differences in pore geometry of samples. The technique is based on the observation that the location and shape of a capillary pressure curve reflect characteristics of the pore structure of the sample. INTRODUCTION It has been noted1-5 that the observed differences in shape and location of capillary pressure curves reflect some basic properties regarding the pore geometry of the samples. For example, according to basic concepts of capillarity, the following statements can be made regarding the location and shape of a capillary pressure curve.* The location of the curve with respect to the (Vb)pc and PC axes is a measure of the interconnected pore volume and of the cross-sectional area of the pore first entered by mercury, respectively. The shape of the curve depends on the interconnection of the pores and the sorting of the pore sizes. It has been the object of this study to use this information as a starting point in an attempt to find a unique mathematical description of the PC — (Vv)p, relations of different samples. It may be expected that parameters in such a relation can then be used to describe differences in pore geometry of these samples. For a practical description of the PC — (Vb)p, relation, however, it appears desirable to describe each curve (i.e., each sample) by a limited number of parameters so that the curves taken from all samples form a family, each member of which is uniquely determined by one single combination of values of all parameters.

By C. W. MacGregor

IN the testing of materials there exist various methods of recording graphically the behavior of a material subjected to tensile stress. Prob-ably the most common method is to plot the tensile stress So, obtained by dividing the load P by the original area of cross section AO at the start of the test, as a function of the strain ?o, which is obtained by dividing the ?Lo or the change in the gauge length by the original gauge length Lo. A list of the symbols used here is given in Table 1. This method, while it has proved useful in the routine testing and comparison of various materials, does not have a very sound physical basis, as was first pointed out by P. Ludwik1, and consequently does not afford a very deep insight into the true physical behavior of the material under stress. Among the objections to this method may be mentioned: (1) that by dividing the load P at any stage of the test by the original area Ao a fictitious stress is obtained, which does not actually exist; (2) that the strain ?o = ?Lo /Lo is not an exact expression for the true strain for large values of ?Lo in per cent of Lo; (3) that when necking starts the strain varies considerably along the gauge length and the above expression no longer gives the true strain existing at any point on the outside of the bar; and (4) that the axial strain varies over the cross section of the necked portion and ?o does not represent an average of these strains over the cross section. Stresses taken from such a diagram would be only approximate and, if used to compare results of a test on a given material under simple tension with results obtained under combined stresses, certain errors would he thus introduced. In order to overcome some of these objections, various methods have been suggested, both as to the quantities to be measured and as to their graphical representation. In some cases the so-called "true stress," obtained by dividing the load P by the actual area of cross section A existing when the load P was applied, is plotted as a function of the strain

Jan 1, 1937