Search Documents

Efficient project planning during the detailed feasibility to final engineering stages of a project requires not only the accurate prediction of the grade, tonnes and recovery, but their degree of variability as well. An understanding of the major parameters involved in the grade and tonnage estimates is essential, and the communication to those receiving the results is most important. The personnel involved in the project require more than just a global reserves classification. Quality parameters other than grade should be evaluated as carefully as the estimate itself. This paper does not present any novel ideas to overcome or enhance any of this. Rather, it takes a step back and tries to look at the global picture of requirements for proper project planning.

Jan 1, 1987

By Bassett N

The Eneabba deposit, located 280 km north of Perth, Western Australia, and 30 km inland (Fig. 1) is one of the most recently developed deposits of mineral sands in the world. The area has been in production since 1974, while the Associated Minerals Consolidated Limited (AMA) operation commenced production in 1976. Total ore reserves of close to 400 million tonnes contain about 40 million tonnes of heavy minerals (proved and probable).

Jan 1, 1979

In seeking to improve the economic performance of mines, the management or human aspects are usually seen to be quite seperate from, and more significant than, the technical aspects. There are obvious aspects of industrial relations, man-management, skills training and supervision that are currently the focus of efforts to improve the productivity and quality of the mining process. However technology also has a lot to offer. Analysis of the costs involved suggests that innovations leading to improvement in the productivity of the excavation and transport of overburden and the recovery of coal (both in the mine and preperation plant) can lead to improvements in the economic performance of a mine that may outstrip the obvious non-technical or management opportunities for improvement. While there are some innovations currently being investigated within the industry that relate to the design of mining equipment, the type of machinery being used in open cut mines has not changed dramatically over the last twenty five years. It is also likely that mining equipment will remain essentially of the same form in the forseeable future. If significant improvements to mining performance are to be achieved other than by futher increases in the scale of machinery, then we need to seek ways to operate these same types of machines in a more productive and controlled manner. This paper discusses the identification of mining processes the improvement of which is likely to have a significant effect on mining costs and performance. Some areas of current research are discussed and potentially fruitful areas for future development are identified.

Jan 1, 1991

By E R. Ramanaidou, M Wells

The aim of this paper is to summarise all known Phanerozoic ooidal ironstone deposits worldwide, including Australian deposits such as the well-known channel iron deposits (CID). Nearly 400 occurrences have been catalogued based on stratigraphy, geographical coordinates, facies, grade, tonnage and iron bearing ore minerals. The description also includes details on the geochemistry, genetic models and main references. Brief statistical analysis provides an overview of the variation between these deposits. This compilation offers a basis for better understanding of the ooidal ironstone deposits and a global evaluation of this important resource worldwide.

Jan 1, 2009

By Brown N. R

This paper attempts to highlight some of the problems encountered in the economic exploitation of the deeper coal seams by opencast mining methods. The major cost elements of three methods of overburden removal are examined in relation to the overall cost of winning coal from deeper-lying coal seams. The three overburden removal methods examined are dragline stripping and two systems combining dragline stripping with shovels and trucks at varying depths of overburden. A dragline is, undoubtedly, the most cost effective system of overburden removal for depths of up to 30 metres but it is suggested that, when dealing with incremental overburden depths in excess of 30 metres, engineers should consider carefully the possibility of using a shovel and truck operation, or other system, to augment the use of a dragline.

Jan 1, 1986

By Hargraves AJ

Pre-drainage experiments have been conduct- ed at Appin, Cook, John Darling, Leichhardt, Macquarie, Metropolitan and Moura No. 2 Collieries. Appin (550 m deep) experiences particular gas problems in development drivages, and the almost pure CH4 seam gas makes difficult tiro compliance with statutory maxima in intakes and returns. Patterns of 43 mm diameter drain- a,.;e holes drilled ahead and laterally into virgin coal have improved gas conditions in working places and have allowed tolerable advance rates. Cook, Leichhardt, Metropolitan and Moura No,. 2 Collieries have experienced gas and stress phenomena ranging from conical bursts less than one tonne to full scale instantan- -us outbursts of hundreds of tonnes with tens ,f thousands of cubic metres of seam gas. Gas ~Irainage experiments with patterns of holes up a,, 200 mm diameter have been undertaken with ;,;siness monitors on the coal to establish .lative effectiveness. Incremental flows into mg 43 mm diameter boreholes have investigated drainage patterns relative to length, and at comparative incremental flows have nlicated lowered permeability zones at stress ,.,utments. In some CO2 seam gas areas where iammability problems are reduced to perhaps ii, but where outbursts proneness is increased,

Jan 1, 1982

Firedamp drainage has become an essential part of many mine environmental systems, and new applications are arising. Installations are evolving further to satisfy ever changing basic requirements, standards, and iniilny needs. In this paper, water seal, vacuum based installations are considered, as well as moni- toring, protective and control systems which have been developed for continuous, manless, and trouble free operation. Some factors affecting plant capacity and extractor per- formance are identified and assessed. INTRODUCTION Firedamp drainage applications are incr- easing world wide as mining engineers strive for improved safety and security, and further concentration of coal output. Fewer and fewer mines are able nowadays to satisfy coal prod- uction and firedamp control requirements solely by air dilution or by air dilution and underground firedamp extraction plants. As a result, dependence on surface extraction plants is increasing. This paper deals with som requirements and applications of such installations. I. DEVELOPMENT AND PRACTICE Firedamp drainage has existed for over 250 years following the early work of Carlisle Spedding at Whitehaven (1730). Some fundamentals of current firedamp drainage systems can be recognised in the

Jan 1, 1982

By M Singh, R C. Steinhaus, J J. Rust

Metallurgical process control systems in mineral plants often employ state-of-the-art monitoring analysers in an attempt to optimise plant operations and enhance mineral recoveries. These systems are unfortunately invariably fed by simplistic ‘sampling’ designs consisting of various in-stream methods or pressurised probes. These are unfortunate compromises and provide a false picture of what a mineral flotation or other process can achieve. The situation is further aggravated by some manufacturers using misleading marketing to suggest discrete cross-stream methods for metallurgical accounting and unreliable continuous in-stream off-takes for control sampling and that they are of synonymous integrity.Reliable, absolute or representative samples are often absent in many modern day concentrator plants, due to compromises around sample taking, particularly in terms of delineation and extraction errors and thus leading to sample bias. For more reliable information from online analysers we need a continuous, but much more reliable sample taken, than is current practice.Online analysers require a fully proportional and continuous supply of sample for effective process control, otherwise maximised or benchmark recoveries will be nothing but a pipe dream. Large discrete cross-stream samples from mechanically less reliable equipment cannot be used as feed to online analysers, as it will negatively impact real-time feedback and efficient process control.It is possible to build correct sampling systems that could do both process controls online and metallurgical accounting at the same time. Multotec Process Equipment (Pty) Limited, in close association with experienced sampling consultant Francis Pitard, have jointly patented a concept to achieve this and which is embodied in the design of the unique Rotating Cone® Sampler (International Patent Application No. PCT/IB2016/057464). This versatile unit for dry and wet applications has high division ratios via two-step sampling and division.A prototype was built and tested to validate the design and levels of precision achievable when employing the unit to split dry mineral fines or even certain foodstuffs.CITATION:Steinhaus, R C, Rust, J J and Singh, M, 2017. Does process control sampling always have to be a compromise?, in Proceedings Eighth World Conference on Sampling and Blending , pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By M Littlefair, D Gribble, R Rounsley, I Te

Low-density explosives (LDE) have applications where the explosive properties of ANFO are not well matched to the rock. In particular, rocks that are of low strength and/or well fragmented in situ. Dyno Nobel Asia Pacific (DNAP) has developed a new LDE, BlastLiteTM, which can be used as a cost-effective replacement for ANFO with excellent detonation characteristics. The product is based on ANFO with the addition of a bulking agent. The key to the product lies in the ability of the bulking agent to form a homogeneous blend with ANFO without the need for any emulsion matrix to bind the product together. This results in an LDE of low cost and high weight strength compared to existing commercial LDE products. The product has been trialled extensively and has proven to provide results that are equivalent to, and often better than, ANFO with reduced powder factors. This paper details the laboratory development and results of field trials for DNAPÆs LDE solution: BlastLite.

Jan 1, 2004

By A M. Lechner, S Arnold, M J. Gillespie, P D. Erskine, D R. Mulligan, A T. Fletcher, A Gordon

Mine ecological monitoring schemes are often conducted only to address compliance and in some cases do not have the sufficient statistical power or understanding of ecological systems to assess, quantitatively, the meeting of rehabilitation targets or mine impacts. Monitoring schemes for rehabilitation commonly rely on analogue sites or premining baselines (reference sites) to assess whether rehabilitation sites are ecologically similar and thus successfully rehabilitated. In the case of monitoring for mine impacts, if the impacted sites diverge from reference data, the site is considered to be impacted. Fundamental to any monitoring scheme is testing the sampling design to ensure that it can detect these differences if they are present through adequate sample sizes (ie statistical power). However, a good understanding of the ecological system is required to ensure that differences detected are ecologically significant. Modelling ecosystem properties can provide a quantitative understanding of how ecosystems change over time and space, in response to natural environmental variations and thus aid in determining significant ecological differences. Furthermore, modelling methods can be used to predict future ecosystem states. Within the ecological literature, guidelines for robust statistical monitoring designs and modelling methods exist but are not routinely being used in the mining industry. This paper uses simple examples to discuss: problems with current compliance monitoring methods; importance of robust statistical techniques; and how modelling can assist rehabilitation assessment and guide monitoring schemes. The aim of this paper is to describe general monitoring and modelling methods that could be potentially used for mine site monitoring and closure assessment. These methods are often considered by mining companies as an extra expense that provide little practical benefit, and the domain of academia; however, engaging these methods may be more cost-effective in the long-run than conducting untargeted monitoring schemes that give no confidence to regulators on whether rehabilitation criteria have been met. Furthermore, monitoring programs in mining contexts provide a good opportunity to better understand long-term ecological patterns and test the application of more rigorous modelling approaches as the life of many mines tends to be greater than ten years.CITATION:Lechner, A M, Arnold, S, Fletcher, A T, Gordon, A, Erskine, P D, Gillespie, M J and Mulligan, D R, 2012. Embracing modern ecological methods - Monitoring and modelling for mine closure, not compliance, in Proceedings Life-of-Mine 2012 , pp 25-32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By A D. Paktunc

The surface reactivity of underwater deposited, high-sulfide copper mine tailings was evaluated under fresh and saline water cover conditions by measuring the surface and pore water quality as a function of time. The experiments were conducted in aquarium type lysimeters having a shallow, well-aerated water cover up to approximately 0.25 m over the tailings. Natural lake water was used for the fresh water cover and seawater for the saline water cover scenarios. The tailings showed significant surface reactivity and oxidation under both fresh and saline water cover conditions. The surface water quickly became moderately to highly acidic, and surface oxidation of the tailings resulted in increased dissolution and release of sulfates, iron (total), calcium, magnesium, aluminium, manganese, copper, nickel, zinc, lead, cobalt and silicon to the water covers. A moderate to slightly increased loss of total sulfides, including pyrite, chalcopyrite and sphalerite, occurred in the tailings surface layer to a very shallow depth. In comparison to the fresh water cover, the complete acidification of the saline water cover was delayed by approximately 30 - 40 days because of its additional available alkalinity. Whereas the rate of surface water acidification and release of aluminium and silicon were moderately reduced under saline water cover conditions in comparison to those for the fresh water cover, the release of calcium, magnesium, iron (total), copper, nickel, lead, zinc, sodium and potassium were enhanced. The mass transfer fluxes for dissolved copper, nickel lead, zinc and iron (total) from the tailings substrate to the surface water cover following surface water acidification were higher by 50 per cent or more in the saline water cover than those in the fresh water cover. This release was also reflected in moderate loss of pyrite, chalcopyrite and sphalerite in the very shallow upper surface layer of the tailings at the tailings-water interface, although the loss of pyrite in the surface layer was less pronounced. In both cases, the dissolution of aluminosilicate minerals moderated, to a certain extent, pH and acidity in the water cover.

Jan 1, 2003

Mine planning typically involves designing an operation to uncover coal with the minimum initial costs with reclamation planning and earthworks being done as an "add on" task. The landform is too steep to remain stable, has no drainage and frequently has areas of excessive acidity or alkalinity. Extensive earthworks are required to reduce grades to an acceptable level and create a drainage system. The flexibility available to the mining engineer to alter the post mining landscape clearly depends on the mining methods. Straight dragline stripping provides virtually no flexibility. However most mining operations over the term of current ten year plans have a substantial pre-strip component. It is this pre-strip material which has the potential to reduce the final reshaping earthworks. The reshaping operation itself is subject to some flexibility with various options being available to re-grade and provide drainage. The full utilisation of this flexibility to minimise earthworks cost should be the aim of reclamation design. ACIRL's current thrust in reclamation is aimed at the integration of mine planning and reclamation earthworks. This involves gathering all environment and agricultural criteria and designing the earth works necessary to produce an acceptable final landform. A key component of our work is the use of computer aided design (CADD) for the design of spoil piles, pre-strip dumps and spoil re-shaping. This approach has been applied to a number of mine sites with earthworks operations covering hundreds of hectares and hundreds of millions of cubic metres volume. We are continuing to provide that consultancy service and at the same time are involved in the development of more sophisticated software tools to apply to reclamation design.

Jan 1, 1991

By D Hunter, N Cusworth, J Miller

"Recent project failures have called into question the use and relevance of benchmarking and independent reviews, forcing a rethink of traditional processes and procedures.With cost estimates and schedules dramatically varying from lows seen around the global financial crisis to peaks experienced in the recent mining boom, benchmarking has ranged between essential and misleading.Profound shifts are now underway in future project delivery strategies as the market moves away from cost-plus engineering, procurement and construction management. The current trends in project implementation are to utilise more lump-sum design and construct or fixed-price supply and construct contracts. This trend will remove transparency in detailed cost information by reducing the sources and clarity of cost data.Independent peer reviews (IPRs) of studies and investment recommendations performed over the last decade have both failed to prevent flawed or deficient projects from proceeding to approval and funding, and been successful in ensuring that owners did not proceed with doomed investments.In recent times, it has been recognised by some owners, contractors and engineers that traditional benchmarking checks or IPRs, or a combination of both, will not necessarily produce reliable assessments of study conclusions and of the forecasts of project outcomes. To be of value, the benchmarking process now also needs to recognise the highly volatile responses from the engineering and construction industry to the current and future markets for their services.Similarly, reviewers who draw upon benchmarks of past project experiences on an understanding of the things that shaped and influenced their outcomes need to be more aware of how a future dynamic market may impact the outcome of the projects and raise warning flags accordingly.With the commodity cycle currently approaching what is hoped is its bottom, ensuring that benchmarking and independent reviews evolve into reliable, transparent and worthwhile processes becomes even more important. This can only be achieved with more transparent and analytical benchmarking and business-orientated reviews that both recognise and calculate the impacts of dynamic markets on project implementation.CITATION:Cusworth, N, Hunter, D and Miller, J, 2016. The role of benchmarking and independent reviews, in Proceedings Project Evaluation 2016, pp 249–259 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Nakajima A

Some attempts were made to recover uranium from aqueous systems by using various biosubstances including microbial biomass. Of hundreds species of microorganisms tested, extremely high uranium absorbing ability was found in Pseudomonas stutzeri, Neurospora sitophila, Streptomyces albus and Streptomyces viridochromogenes. In parallel to this research, various kinds of biomass and commercially available crude drugs were screened to measure their abilities to adsorb uranium. Of these biosubstances tested, high uranium adsorbing ability was observed in chestnut skin, Comi fructus, Geranii herba and Chaenomelis fructus. From these results it may be considered that the uranium adsorbing ability of these biosubstances is due to the following; the uranyl ion is co-ordinated by the polyphenolic compounds such as tannin existing in the biosubstances. Along with these fundamental researches, we have developed a new adsorbent, the immobilised persimmon tannin (kakishibu tannin), for uranium and thorium. This adsorbent can accumulate 1.71 g of uranium per gram of the adsorbent (14 mEq/g), and the uranium adsorbing capacity of this adsorbent exceeds by several times that of commercially available chelating resins (2 - 3 mEq/g). We attempted to recover uranium from uranium refining waste water by using the immobilised persimmon tannin. As a result, the immobilised persimmon tannin can recover trace amounts of uranium from uranium refining waste water containing 10 - 15 ppb uranium with high efficiency. Almost all of the uranium adsorbed onto the adsorbent can be desorbed by washing with 0.05 - 0.1 M HCl or H2SO4. Thus, the immobilised persimmon tannin can be used repeatedly in the adsorption-desorption Cycle.

Jan 1, 1993

By S Roberston, G Batt, R Shanahan, B Shah, A Trench, H Bromfield

The geographic imperative of ore systems leaves mining, more so than virtually any other aspect of modern industry, heavily dependent on obtaining and maintaining social licence to operate. A prospective miner cannot arbitrarily walk away from a deposit in search of more favourable community perceptions – concentrations of mineral endowment represent highly specific and fixed elements of the landscape, and their development and extraction thus requires the acceptance and trust of a specific network of landholders and stakeholders, sometimes with diverse and even competing interests in the development and use of the local environment. Weakness or absence of such social licence can bring added costs and complexity to developing and operating a mine – and in extreme cases even result in project failure. Because it must be maintained throughout the life of a project, such social risk becomes a substantial part of overall project risk profile, particularly during routine operations once initial technical and development risks have been largely resolved.CITATION: Bromfield, H, Roberston, S, Shah, B, Shanahan, R, Trench, A and Batt, G, 2018. On equitable distribution of mining wealth and the social licence to operate imperative – an African case study, in Proceedings Complex Orebodies Conference 2018, pp 6–7 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By S Gezgin, F Beckstein, M Müller, D Rapp, D Sergeev, J Qi, A Lichtinger

Salts and their mixtures play an important role for industrial and energy sectors, eg metallurgy, biomass gasification and combustion, nuclear and solar powerplants and electrochemical processes. Depending on the composition of salts (eg Li+, Na+, K+, Mg2+, Ca2+ // NO3-, F-, Cl-, CO32-, SO42-, etc), the temperature range for different applications can vary starting from room temperature and going up to 1500°C. For the proper design and modelling of heat exchangers and other equipment, it is necessary to have reliable and validated data sets of thermophysical properties. The 50 mol per cent NaNO3 – 50 mol per cent KNO3 salt mixture as a well-studied composition was selected for validation of relevant thermophysical properties (heat capacity, enthalpy of phase transitions, thermal expansion, viscosity and thermal conductivity). To study these properties of the liquid phase, special crucibles and approaches should be implemented. Verification of these crucibles for different methods (differential scanning calorimetry (DSC), thermomechanical analysis (TMA), laser flash analysis (LFA) and rheometers) has been performed. The low thermal conductivity of salts is one of the main problems in implementing latent heat storage. In this project, the authors intend to develop a fundamental solution to this problem using chemically bonded metals with salts. These are known as metal-salt solutions. To fit the main parameters of new phase change materials to the requirements of thermal energy storage, a wide variety of possible combinations should be considered. CALPHAD modelling is used together with thermal analysis for the development of a consistent thermodynamic database including chloride salts (Li, Na, K, Mg, Ca // Cl) and corresponding metals (Li, Na, K, Mg, Ca). The results of the study of quasibinary and multicomponent metal-salt (eg Mg-KCl and Ca-KCl) systems as well as the selection of suitable crucible materials and challenges by studying of these systems will be discussed.

Aug 21, 2024

By Quast K

A series of laboratory flotation tests were conducted to evaluate the effectiveness of various depressants as arsenic (and zinc) depressants in the lead cleaner stage of the NBHC mill at Broken Hill. The depressants used included potassium cyanide, ferrous sulphate, sodium hypochlorite, potassium ferricyanide and two Cyanamid commerical depressants, Aerodepressants 610 and 633. A standard roughing stage was completed before the addition of the reagents in the cleaning stage. All reagents tested produced significant arsenic depression, with the best results being obtained with the addition of potassium cyanide and sodium hypochlorite. Some of the depressants activated the zinc in the process of arsenic depression. The best result was obtained with the addition of 90 g/t potassium cyanide at a pH of 10 when arsenic recovery was only 1/4 that of the value obtained for the standard test.

Jan 1, 1991

By J Player, K Braddon

High productivity mining is the key to the financial success and stability of modern mines. This can be achieved through the use of new technologies, the development of innovative work practices and optimisation of the mining method to suit the mining environment. Big Bell Mine is a 1.7 Mtpa longitudinal sublevel caving operation at a head grade of 3.14 g/t. Annual production is 170 000 ounces of gold. The selection and implementation of bulk emulsion explosives was seen as the logical progression from blow loaded ANFO for the high tonnage rate required from the longitudinal sublevel cave. Prior to the implementation of bulk emulsions an investigation was required to examine the technical and financial benefits available with the introduction of bulk emulsion. This paper examines the review process and the successful implementation of bulk emulsion explosives at Big Bell.

Jan 1, 1999

The Shamrock Gold Mine has been brought from exploration to production within three years. Mining of the openpit is scheduled for June 1990 with commissioning in April of the 180 000 TPA carbon-in-pulp mill on old tailings and rock dumps. The development of a small openpit containing 344 000 tonnes at 3.6 g/t Au in a complex sulphide ore has required extensive metallurgical testwork to optimise recovery, and ensure profitability. The project has been undertaken in a changing economic climate, with increasing restrictive legislation. The decision to mine was further complicated by the escalating cost of installing a heap leach operation in South East Queensland. Decreasing costs of consumables, in particular sodium cyanide, and the opportunity to purchase a suitable transportable mill at a reasonable price made the project robustly viable as a CIP operation.

Jan 1, 1990

By J Player, K Braddon

High productivity mining is the key to the financial success and stability of modern mines. This can be achieved through the use of new technologies, the development of innovative work practices andoptimisation of the mining method to suit the mining environment.Big Bell Mine is a 1.7 Mtpa longitudinal sublevel caving operation at a head grade of 3.14 g/t. Annual production is 170 000 ounces of gold. The selection and implementation of bulk emulsion explosives was seen as the logical progression from blow loaded ANFO for the high tonnage rate required from the longitudinal sublevel cave.Prior to the implementation of bulk emulsions an investigation wasrequired to examine the technical and financial benefits available with the introduction of bulk emulsion. This paper examines the review process and the successful implementation of bulk emulsion explosives at Big Bell.

Jan 1, 1999