Search Documents

By Payne P, Beirne W, Geldard D, O&apos

Whim Creek Consolidated N.L. has operated openpit mines at Meekatharra since 1980. Mining operations commenced with the Haveluck openpit and the Phar Lap openpit was started in 1 984. Grade control in the Haveluck mine was simple because the orebody showed good continuity along strike and down dip and had an easily recognisable hanging wall contact. Problems were encountered once mining corn menced at Phar Lap because of the complex lithologies, alteration and faulting involved. Simple grade control techniques developed for Haveluck failed and were not solved until an understanding of the ore bodies was achieved.The integration of all geological data into the interpretation of the developmentdrilling results has proved essential to achieve effective grade control atreasonable cost.

Jan 1, 1986

The paper is introduced by some general comments on the Electrolytic Zinc Company West Coast Mines operations. An outline of the geology of the Rosebery Mine orebodies preced- es a resume of the mining methods used prior to the current mechanization programme. The reasons for the introduction of longhole stoping techniques are given together with a brief explanation of both sublevel longhole and longhole stoping methods. The application of remotely controlled loaders within these stoping methods is discussed. A description of the remote control mechanisms, used on Atlas Copco 310 and 511 Cavo loaders, is followed by comments on these mechanisms from both a maintenance and production viewpoint. A summary of perform- ance statistics and operator safety records vindicate the selection of remotely controlled loaders for the longhole stoping areas at Rosebery Mine.

Jan 1, 1977

By J Zeni

In 2001, the Springvale Coal Mine determined a requirement for a 360 m deep vertical airway to ventilate ongoing underground longwall mining operations. The project, referred to as the Springvale No 3 Ventilation Shaft, was completed in 2003 - 2004 by blind boring a 4.25 m diameter hole from the surface to the coal seam at 360 m depth. The shaft was completed with a 3.5 m inside diameter lining made from a continuous watertight steel and concrete composite pipe. Presented from both the clientÆs and the contractorÆs perspective, the following paper describes the process of constructing a blind bored ventilation shaft for this application. Beginning with the clientÆs definition of the requirements and specifications for the shaft, the paper describes the steps followed by Springvale Coal prior to awarding the contract. Springv aleÆs process involved a thorough site investigation including procurement of geotechnical data for prospective contractors and the management of issues relating to safety, quality and the environment. The clientÆs view is followed by a description of the planning and works performed by their nominated shaft drilling contractor, Ardent Underground Pty Ltd.The contractorÆs description of the works includes the details of the blind shaft drilling and lining construction process used for this application. The design of the shaft lining installed at Springvale Coal was the first of its type to be used in Australia. The successful installation of a watertight composite shaft lining and the safety of the method, which did not require any personnel to enter the shaft or the mine, were among the positive outcomes from the project.

Jan 1, 2005

By J R. Manuel, M J. Peterson

Selected drill core samples from a Ferrobamba-limestone-hosted, magnetite-haematite skarn deposit, located in the Apurimac department of the Andahuaylas-Yauri skarn/porphyry belt of south-eastern Peru, were mineralogically and texturally characterised to gain a preliminary indication of the deposit's potential as an iron ore resource. Optical microscopy, X-ray diffraction (XRD) and scanning electron microscopy/electron probe microanalysis (SEM/EPMA) techniques were utilised to determine the characteristics of magnetite, haematite and/or goethite dominated ore types, including variations in the relative proportions and textural relationships of the ore and gangue minerals. The deportment of elements deleterious to processing performance (eg copper, sulfur and potassium) was determined and the beneficiation potential of the samples was briefly assessed. In drill core sections, the ores are grey to reddish in colour, massive and 'metallic' to dark brown and earthy in character, moderately hard and porous (macro and microporous), with variable gangue infill. Ores often appear weathered, typified by ochreous goethite staining and common minor goethite (except in dense core fragments), occasionally exhibiting a more friable texture with coarse magnetite/martite grains. Silicates and lesser carbonate gangue are visible as blue-green to beige to white scaly and/or shaly surface coatings, and finely particulate infill, often goethite stained. Sulfide-rich ore types also occur in part of the deposit, but are restricted to specific drill holes. Magnetite grain size is relatively coarse, compared with magnetite from typical banded iron formations, whereas discrete silicate gangue is mainly bladed/fibrous and/or layered and micaceous in form. XRD analysis indicates the presence of vermiculite, serpentine, stilpnomelane, chlorite, actinolite and clays. There is a spectrum of ore types representing the gradation from 'fresh' (magnetite-dominated) to oxidised and weathered (martite/goethite-dominated). Martite-dominated samples are generally higher in grade, due to leaching and removal of silicate gangue, resulting in higher macroporosity. Where gangue has been leached out, partial replacement by vitreous goethite and/or hydrohaematite is typical, often preserving the fibrous/layered characteristics of the original silicates.

Jan 1, 2009

Porgera is located in the Central Highlands of Papua New Guinea. Porgera Joint Venture treats a high grade epithennal gold deposit. Most of the gold occurs as submicroscopic particles in a sulphide matrix although there is some quite coarse free gold. Anticipated gold production is 900 000 oz per year for the first six years of operation.Stage I of the treatment plant consisted of a concentrator and leach/CIP Circuit. It was commissioned in August 1990. Design throughput was 1500 tpd with an anticipated gold recovery of 60 per cent. Throughput achieved was actually 1850 tpd with an average gold recovery of 69 per cent. CIP tails were accumulated in a pond awaiting retreatment by pressure oxidation.

Jan 1, 1992

Industrial relations on Australian and New Zealand resource projects can be volatile. Therefore investors have become increasingly aware over the years that sound industrial relations during construction is vital to the overall success of their project. There has been a wide range of actual industrial relations performance, project by project, and the degree. of success often directly correlates with the degree and thoroughness of pre-project planning. However, although many projects have been crippled by delays and cost overruns because of labour disputes, good results are achievable. Total commitment to the project by all parties involved is essential and it is up to the employers to seek out this commitment and not just trust mother luck. Industrial relations must be taken very seriously as the price of failure can render a resource project unviable.

Jan 1, 1983

By Rongqing Q, Tiancong Z, Yiyuan L

The influence of pulp density, ferric ion concentration and particle size on the tank bioleaching of two kinds of refractory gold concentrates are discussed. The chemistry and mechanism of the bioleaching process are also presented. The relationship between oxidation of sulphides, liberation of enclosed gold and gold cyanidation are discussed. The consumption of NaCN could be reduced by alkaline treatment of bioleached residues prior to Cyanidation.

Jan 1, 1992

By Flloyd J. M

A continuous oxygen probe,incorporating a SIRO2 solid electrolyte oxygen sensor which measured the oxygen potential of a small volume of gas enclosed above the melt's surface,was constructed and tested. The oxygen potential of iron-silicate slags in equilibrium with solid iron in the temperature range 1250 to 1300¦C were measured continuously for tests of up to 40 hours duration. Results were in agreement with those of previous workers using gas equilibration techniques. Tests on non- iron buffered slags proved unsuccessful due to corrosion of the probe's component in contact with the slag and an alternative material is Required.

Jan 1, 1987

Faced with low prices and weak demand in an oversupplied market, the Australian coal industry must seek to further reduce its costs. The paper examines minesite competitiveness of the open cut coal industry in Australia with some references to the coal operations of M.I.M. Holdings Limited. The make-up of F.O.R. mine costs is analysed in order to identify where efforts should be directed to maintain competitiveness. The scope for mine site improvements through changes to working practices, the application of new technology and cost management is examined.

Jan 1, 1987

By Senanayake G

A sample of crude copper powder produced by the CLEAR Process was refined by dissolution and recovery in sulfate media using the Parker Process. The Parker Process offers an alternative method of copper recovery to electrorefining and allows a range of Eh and pH conditions to be used to provide further discrimination of impurities. High purity copper powder was recovered by the Parker Process even in the presence of added impurities when the Eh and pH was maintained near constant throughout the refining step.

Jan 1, 1984

By Bhattacharyya AK

A two-dimensional finite element modelling technique is applied to predict the subsidence movements on a sloping ground surface above a completely mined panel. The modelling is carried out for the surface both directly and using a combination of an equivalent horizontal surface and a rays projection method and the result compared. The rays projection method provides the subsidence components on a sloping surface from the corresponding ones on an assumed equivalent horizontal surface through the point of mean elevation of the relevant part of the sloping surface. This method is used next to compare the subsidences, horizontal displacements and horizontal strains from the mining of a given panel at the surface for different inclinations. The results show that the magnitudes of the subsidence components are greater on the dip side of the slope from the point of the mean elevation, than the corresponding ones on the rise side and the asymmetry increases with the inclination of the surface. The findings are also compared with those of other research Workers.

Jan 1, 1992

Naturally occurring rutile contains approximately 96 per cent titanium dioxide (Ti02), whereas the product from the ilmenite reduction - aeration upgrading process, "sub- rutile", contains only about 92 per cent Ti02. Therefore, there is an-incentive to lift the quality of sub-rutile by removing transition metal impurities, in order to supply a more valuable and marketable product, particularly for the chloride-route pigment producers. Previous studies have shown that the sub- rutile residual iron content (of approximately 4 per cent) and residual manganese content (of approximately 1.5 per cent) are chemically bound within the titanium-oxygen mineral lattice, and are most difficult to remove by simple leaching methods. In attempts to improve their eventual removal, a simple process modification has been successfully investigated in laboratory scale trials. Transition metal sulphides have been formed in the reduced ilmenite by using a "sulphur-doping" technique during reduction (metallization) conducted at controlled temperatures. These compounds give rise to greatly enhanced dissolution of the unwanted transition metal constituents during the sub- sequent aeration and acid washing steps. Thus, the manganese content of the final sulphur- doped, reduced-aerated, acid washed product can be reduced by about 90 per cent to 0.2 per cent, and the iron content by about 70 per cent to less than 1.5 per cent, in comparison with those levels remaining after unmodified pro- cessing. Additions of sulphur as low as 2 per cent of the weight of the ilmenite have proven satisfactory. Preliminary studies reveal that the modified process is economically feasible. These results suggest that the sulphur content of the Collie coal char used in an unmodified reduction step must exert some influence on the eventual removal of iron and manganese during aeration and acid washing.

Jan 1, 1973

This paper reviews the role of fill in mining including consolidated fill both histor- ically and currently as determined by a recent survey of the Fill Subcommittee of the Canadian Advisory Committee on Rock Mechanics (CACRM). It covers the application of fill in modern min- ing methods including mechanized cut and fill, undercut and fill, post pillar cut and fill and longhole pillar recovery between stabilized fill. An automated fill preparation plant and recent developments in rotary drilling of hydraulic fill conducting holes are described briefly. The paper also summarizes the findings of some of the important laboratory and field work carried out on the behaviour of fill in Canada, the United States and Australia and again draws on current information obtained from the Fill Subcommittee of the CACRM. Space limitations and unavailability of suitable material prohi- bit the summary of similar information from other countries.

Jan 1, 1973

By P W Haines

The McArthur, Balma (new name) and Habgood Groups are thick (up to 4.5 km) correlative sequences of shallow water evaporitic carbonates, mudstones and sandstones that are exposed largely within the Batten, and southern and northern Walker Fault Zones (Batten and Walker Troughs) of the McArthur Basin respectively. Recent re-mapping of the Walker Fault Zone has provided data for refined stratigraphic correlations between these groups. Two significant hiatuses are now recognised within the Balma Group (base of Vaughton Siltstone and base of Yarrawirrie Formation) and these may represent tectonically-generated sequence boundaries which may correlate with similar local hiatuses within the McArthur Group such as at the base of the Teena Dolomite and Lynott Formation respectively.

Jan 1, 1994

By Shonhardt JA, Bagster DF

This paper firstly examines the pollu- tion potential of burning colliery wastes. A comparison of two means of estimating the pro- pensity for coal to combust spontaneously is next presented. The use of microwaves, as a new procedure, is discussed in detail, while a comparison of the results is made with a modi- fied adiabatic technique. A number of coals that are known to combust spontaneously was tested, as were some coals that are not consi- dered to have self heating potential.

Jan 1, 1987

By Kissell F. N, Thimons E. D

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined- out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a longwall operation that uses ventilation to carry off hazardous gases, and two are room- and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases, employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1988

Lateritic nickel ore occurs as a supergene or residual deposit as a result of the tropical weathering of underlying ultramafic rocks. The mineralisation may be as hydrated Ni-Mg silicates, like garnierite (silicate ore); or as hydrated Ni-Fe oxide (oxide) ore. Non-sulphide ore represents only 30% of the tonnage mined, but represents 85% of the total world's nickel reserves. A typical lateritic profile consists of 4 zones above the unweathered ultramafic parent rock: Zone 1: the "upper laterite" which is dark red-brown, porous and concentrically structured. It contains 0.2 to 0.8% Ni, 48.0 to 72.0% Fe, and 0 to 9.5% MgO. It is often capped by a ferricrete crust. Zone 2: the "middle laterite", which is red-brown to light brown and more porous than the above zone. It contains 0.8 to 1.5% Ni, 42.0 to 48.0% Fe and 0.5 to 6.0% MgO. Zone 3: the "basal laterite" which is yellow-brown to yellow-orange,

Jan 1, 1974

By E Y. Baafi

Artisanal and small-scale gold mining (ASSM) offers lucrative employment opportunities to the locals of most developing countries. The major drawback of ASSM is its adverse impacts on the environment resulting from improper mining and processing techniques. Papua New Guinea (PNG) has very active ASSM activities. The artisanal and small-scale gold mining in PNG provide employment at local and national levels and the sector is an important source for inflow of foreign exchange into rural communities. However, small-scale mining activities are associated with sensitive health and environmental issues. The process of recovering gold by retorting and heating the amalgam over an open fire is a dangerous health practice. This paper discusses artisanal and small-scale gold mining operations in PNG and their impacts on the local environment.

Jan 1, 2008

By Holla L

There exist several legislative provisions in N.S.W. which work together to control surface subsidence due to extraction of coal by underground methods. The important ones are the Coal Mining Act, Coal Mines Regulation Act, Mine Subsidence Compensation Act and Dams Safety Act. In addition, there are guidelines laid down by the Chief Inspector of Coal Mines for mining under and in the vicinity of tidal waters and the ocean. There are also conditions of coal mining leases and conditions of approvals given to undertake various methods of mining which stipulate further controls. The legislative provisions and relative controls are designed to minimise surface damage, ensure safety , of major public utilities, control- surface land use and compensate damage caused by subsidence as a result of coal mining operations. They aim at balanced and responsible development of our valuable coal resources consistent with adequate safeguards to surface improvements and natural features. The paper discusses in detail these legislative provisions and the mechanics of their operation with a view to emphasising the fact that underground coal mining operations are undertaken responsibly and in a planned and rational manner for the overall benefit of the community. Further, the paper aims to demonstrate the need for legislative measures and conditioning of mining operations to keep abreast of developments in the knowledge and skills of mining and subsidence engineers and continuing improvements in mining technologies. Likewise there is a need on the part of engineers and those associated with introduction of new technologies to appreciate the requirements and existence of legislative and other measures having a direct or indirect association with surface subsidence as a result of coal mining operation.

Jan 1, 1986

By K Thompson

The Diavik Diamond Mine is a world-class operation located in an extreme environment 220 km south of the Arctic Circle in CanadaÆs Northwest Territories. The mine has a number of distinctive characteristics û such as limited winter access via an ice road, mine infrastructure being located on an island, with mining taking place behind dykes holding back a lake, temperatures at the mine that get down to -45¦C in winter, and the presence of bears, wolves, foxes and wolverines! One thing that Diavik does have in common with other mines around the world is the need for reconciliation. In late 2005 Diavik implemented SnowdenÆs Reconcilor software system to facilitate the process of reconciling geological models, mine plans, production data and plant results. This paper provides a case study of the reconciliation system implementation. It outlines the migration of Diavik away from a comprehensive and effective spreadsheet-based reconciliation process to a commercial grade, automated and web-based information management system. This paper documents the reasons for moving away from the spreadsheet system, the key parameters used for reconciliation, and the benefits gained by closing the loop between reconciliation and ongoing process improvement.

Jan 1, 2006