Search Documents

This paper presents the water management plan of the Mae Moh Project in the North of Thailand, which includes a large lignite opencast mine and thermal power plants. Lignite production will increase from the present 5.5 million tons per annum to approximately 20 million tons per annum by 1995 when the pit area will be about 20 sq.km. and the depth at over 300 meters. Seven power plants are proposed of which two are under construction. The total capacity to be installed is 2,925 MW. The principles considered for water management are firstly flood protection, including drainage of the mining pit and diversion of the Mae Moh stream away from proposed future mining areas; and secondly, a plan to meet the water requirement of the thermal power plants, while maintaining downstream supplies for irrigation and other purposes. The limited annual run-off of Mae Moh and Mae Chang watershed basins are inadequate for the proposed power plants. A study has been prepared to compare two approaches, namely conveying water from remote watersheds to meet the water requirement of the power plants up to total installed capacity; or by limiting future total generation, at the existing site, to only 2025 MV.

Jan 1, 1988

By Floyd JM

Pilot plant trials showed the effective ness of the submerged lance SIROSMELT technology for altering the composition of iron blast furnace slags as a preliminary step to produc- tion of formed materials. Mixtures of oil and air were injected into a bath of liquid slag to provide the heat required for melting the additives and to provide very turbulent conditions which resulted in complete dissol- ution of added fluorspar within one minute and almost complete dissolution of silica in two minutes. Sulphur lost during injection was readily made up by addition of pyrite or pyrrhotite. A stable foam could be readily made and broken down and the foamed slag appeared suitable for extrusion or forming into shapes.

Jan 1, 1979

With the recent wider introduction of friction hoists of the Koepe type. for winding from depths of more than 3000 feet it has been found that failure by fatigue is the most common form of rope deterioration. Large numbers of wire breaks occur near the centre of the rope cross-section and it is difficult to detect these with certainty using the preferred d.c. magnetic test. For best results with conventional search coils their dimen- sions should be related to the typical wire break field pattern surrounding the longitudionally magnetised rope. The field of a broken wire was experimentally determined, using a Polish type MD6 Defectograph wire rope testing magnet and a short prepared length of rope with a movable simulated broken wire. The external field distortion perpendicular to the rope was measured by means of a gaussmeter and Hall probe. The advantages of this method are that terrestial magnetism and inherent rope "noise" have no effect on the results.

Jan 1, 1971

By Hainsworth D, Winstanley G, Gurgenci H, Corke P

Past experience has shown that the automation of the dragline swing motion requires real time monitoring of the bucket position. A current project at the Centre for Mining Technology and Equipment (CMTE) is aiming to achieve this using machine vision. The hardware platform is a Datacube MaxVideo 200 system. The images are obtained by a fixed camera installed on the dragline boom. The field of view is large enough to include the bucket in all possible configurations. Standard chain coding and run-length coding algorithms are used to process the video image. The three-dimensional bucket position is calculated by combining the output of the machine vision system with the rope length data obtained from transducers installed on drag and hoist drums. This information is then fed into a control computer which takes corrective action to suppress bucket oscillations before they reach dangerous levels.

Jan 1, 1995

Until recently, nickel laterite projects have been largely ignored, due to their supposedly higher treatment costs compared with sulphides, and to their perceived processing difficulties. A number of laterite projects in the 1970s were abandoned because of high capital and operating costs, while others experienced severe technical difficulties. Conventional wisdom had it that laterites would not be exploited until most of the sulphide orebodies had been depleted. Why then, have Australian mining and exploration companies started a resurgence of interest in the treatment of nickel laterites? It all began with the Bulong project, which has been under study since 1987, while more recently two further projects, Murrin Murrin and Cawse, have been initiated and are being fast-tracked to take advantage of the current high nickel and cobalt prices. A further project in NSW, Syerston, has also been investigated at bench-scale, but no further development has yet been announced. All these projects have the following advantages: 1. Good location near a major mining centre and,reasonably close to power, water, roads, accommodation and a developed service industry. 2. Straightforward, low cost mining. 3. Low cost of acid or sulphur. 4. Good to very good cobalt credits. In addition, there have been significant technological developments in the design and operation of high pressure autoclaves and high rate thickeners, as well as solvent extraction and electrowinning technology. This has helped to decrease capital costs and technical risks, and has allowed the development of alternative flowsheets to the existing laterite operations (Taylor, 1996).

Jan 1, 1996

By Armstrong ME

The gas bubble energy generated by an explosive plays a major part. in the fragmentation, muckpile movement and damage produced. Previously, the interaction between gas pressure and the rock has been interpreted from a theoretical basis or a qualitative study of breakage mechanisms. A method to measure the fluctuations in gas pressure in rock adjacent to the blast has been developed. This peak pressure will vary with structure, as well as with distance and explosive type. The technique is simple to apply and can be used to observe the flow rate of gas at. varying distances. The apparent velocity of penetration is an indication of whether gas has travelled through pre-existing or blast induced cracks. The technique provides a ?n:eans of determining the suitability of an explosive for a given rock type, depending on the amount of displacement desired. The technique has application in optimir.irig throw blasting and predicting and controlling damage, particularly in highly structured rock masses.

Jan 1, 1986

By Harbort G. J

Jameson cell pilot plant trials were conducted in a number of areas in the Red Dome gold/copper flotation plant during 1991. The aim of testwork was to reduce the amount of cyanide soluble copper reporting in tailing to the gold leach plant, and hence reduce cyanide consumption. A number of these tests were conducted in parallel with conventional flotation columns. Laboratory tests were conducted to simulate the performance of the existing plant when compared with the addition of the Jameson cell allowing an extra sulphidising phase. This paper reviews the comparison of the Jameson cell and conventional columns in recovering cyanide soluble copper, while maximising copper concentrate grade. Key parameters that are investigated are residence times, air/pulp ratios, superficial gas recoveries and size by size recoveries. A brief comparison of performance of the Jameson cell and column in the controlled potential sulphidisation process is also presented. An estimation of the reduction in cyanide consumption is given.

Jan 1, 1992

By Kurihara M

In Japan, shield tunneling method is generally used to drive a tunnel in sand layers around the urban area. In this report, appli- cability of NATM (New Austrian Tunnelling Method), which uses rock bolts and shotcrete as support, to water-bearing sand layers is studied aiming at establishing more economical tunnel driving technique. After the geological exploration, the conditions (i.e. pitch of steel supports, water content, cohesion, and fine content of ground,)necessary to ensure the face stability were investigated by using centrifuge loading tests. Concerning measures to manage ground water, an air permiability test was carried out to investigate the effect of the compressed air to cut-off inflow, and pumping test to study the applicability of dewatering. Furthermore, two dimensional elastic FEM analysis consider- ing progress of the excavation face was perform- ed to analyze stresses in the support system and deformation of the ground, and to investi- gate safety of the support and the ground. From these prior investigations, possibility of the applicability of NATM to the present pro- ject was predicted. Finally, based on these results, a real scale field application test was put into practice to confirm the prediction, and to pursue construction efficiency and phenomena which could not have been predicted Beforehand.

Jan 1, 1987

The distribution of p(~rphyt1 copper deposits, in time as well as place, is used to propose an occurrence model based on the genesis models of Sillitoe and Rona. A magmatic source of the metals is accepted. The characteristic metallogenic epoch and the migration of the mineralization event along an elongate metal province are explained as the result of subduction of an obliquely- oriented strip of mineral-enriched material on the oceanic plate. Two mineral-enriched trails emanate from a hot-spot source of high-intensity hydrothermal activity in an oceanic rift. Because the whole plate system moves relative to hot spots, the hydrothermal source appears to migrate along the rift, and the two trails are not parallel to transform faults, but form a broad "V" centred on the hotspot. Source loci are spaced at intervals of about 3000 km, resulting in the possible repetition of metallogenic epochs, in a subduction zone province, at about 100 m.y. intervals. The position of the mineral-enriched strip can be found graphically, given ages of a series of deposits in a province, and the plate convergence vectors. This knowledge provides an exploration tool at regional scale and, by reflection across the rift, the potential for exploration is extended across oceans. The model has implications for commodities and deposit types other than porphyry coppers.

Jan 1, 1987

By P Mackenzie, S Askraba

Pyritic black shales present several challenges to mining operations due to their reactivity. The risk of predetonation of explosives in blastholes, spontaneous combustion of fractured rock and the generation of acid rock drainage must be managed for safety, operational and environmental reasons. At the Mt Tom Price iron ore mine there is a need to differentiate between reactive and non-reactive shale in order to assess risk and make decisions on materials handling. The current approach uses a combination of stratigraphic information and sulfur analysis of blasthole samples. The time taken for sulfur analyses can be a constraining factor on mine production. A new instrument developed by ANSTO Minerals overcomes some of the current limitations on material characterisation. The IOR MeterÖ measures the intrinsic oxidation rate (IOR) of samples of broken rock by circulating air through a sample and monitoring the oxygen concentration over time. The intrinsic oxidation rate is given by the rate at which oxygen is consumed per unit mass of sample, in units of kg(oxygen) kg-1(sample) s-1. Up to eight samples can be measured simultaneously and the turn-around time can be less than 12 hours. Initial trials of the IOR MeterÖ were undertaken at the Mt Tom Price mine in July 2004. The measured IOR of samples from a blasthole pattern spanning different geological layers containing black shale, correlated strongly with the expected reactivity of those layers. The correlation between position in the geological sequence (detailed stratigraphy) and IOR MeterÖ results were much stronger than that between stratigraphy and sulfur content. The new characterisation technique offers the prospect of improving the ability to identify and predict the behaviour of reactive black shales and to differentiate more precisely between different materials. Mine planning, operations, safety and environment all stand to benefit from the success of further trials of the technique.

Jan 1, 2005

By Fukui M

An increase in pig iron output by 50 per cent was aimed at after re-lining No.2 blast furnace of NAKAYAMA STEEL WORKS. This had to be achieved by increasing both the furnace volume (from 673 to 757 m3) and its productivity, Without equipment for high top pressure operation, high productivity was mainly attained by the following three measures; (1) improving the gas flow characteristics by maintaining a high ratio of agglomerated ores, increasing the strength of sinter and coke, and optimizing the charge distribution, (2) decreasing the fuel ratio by low Si operation and the use of hot blast, and (3) oxygen enrichment. In addition, the tapping controls for pig iron and slag were intensified. As a result of the above measures an excellent hot metal output of 2.7 tonne/m3/day was attained in April 1979 (monthly average).

Jan 1, 1980

By Fazakerley VW

The Murrin Murrin deposit is located about 210 km NNE of Kalgoorlie and 50 km E of Leonora in the North Eastern Goldfields region of Western Australia at latitude 28¦ 50'S. longitude 121¦ 54'E on the Laverton (SH 51-2) 1:250 000 map sheet. The tenements are held by Anaconda Nickel NL. Geological investigations between 1994 and 1996 resulted in resource calculations being completed for the ten lateritic nickel cobalt deposits shown in Figure 1. At a 0.8 per cent nickel cut-off the resources at May 1996 for the nine deposits are 116.8 Mt at 1.10 per cent nickel and 0.082 per cent cobalt. The nickel-cobalt mineralisation is contained in a laterite profile developed over Archaean serpentinised peridotites. A bankable feasibility study has been completed and the project is scheduled to be in production by the beginning of 1998.

Jan 1, 1996

Getting it right is a very profitable outcome. Shareholders would ideally like to see their directors get it right all the time on the major economic decisions. But it is very difficult for mining directors to get it right all the time in such an uncertain environment. Primary decision-makers of companies with significant stakes in the mining industry should get it right much more frequently. The legal measures of evidence (beyond reasonable doubt and on the balance of probabilities) can be used to determine whether grade estimates (a key revenue variable) are realistic. The application of this approach can be far reaching. More frequently correct decision-making would result in more effective allocation of limited resources (capital and labour). In turn, this would result in higher financial returns and a more extensive mining industry.

Jan 1, 1994

Wheal Gawler was Australia's first metal mine. This leader was followed by an army of other metalliferous underground mines and surface operations in Australia. As a mine it was not highly significant economically because its small total production of nearly pure galena had low multiplier effects on the economy of South Aus- tralia. Its importance lay in its symbolism: here was a silver-lead mine close to the new town of Adelaide posing the question of what other min- erals lay in the Mount Lofty ranges and in the fields beyond.

Jan 1, 1987

By Piotto P

Pit optimisation algorithms are designed to produce a pit with maximum value, but for certain minerals like iron ore, limestone, coal, etc, it is also necessary that the designed pit contains ore which meets the customer's chemical specifications. This paper describes a technique of using linear programming for blending optimisation and the Lerchs-Grossmann algorithm (as in Whittle's 3D software) for pit optimisation in tandem, to achieve pit designs of targeted grade specifications.

Jan 1, 1996

By Skinner A. J, Thoman B. C

The general structure of microprocessors and their method of use is described, and de- tails given of their application in two parti- cular examples of instrumentation for mineral concentrators. One is in a pulp density gauge, and using this example, the way in which a microprocessor-based unit can be made to be self-calibrating is described. The other is in an on-stream analysis detector for uranium in solvent, where a microprocessor is used to re- place a mini-computer.

Jan 1, 1977

Mr. Bradford said: - On assuming this chair, which has been oc- cupied by so many gentlemen of conspicuous ability, my first words must be an expression of the gratitude I feel for the honour you have done me in electing me to be your President for this year. When considering the subject matter of this address to you to- night, quite frankly may it be stated that for a long time I was on the horns of a very great dilemma, for while I could discourse on the modern political trend in relation to our industries at great length, it appeared to me that this was not the place for such a discussion.

Jan 1, 1987

By Murray G

This paper outlines the processes involved in acid generation from sulphides and the key factors in identifying and predicting time dependent changes in the nature of acid mine drainage (AMD). The initial characteristics of mine water; whether drainage from exposed mining faces, runoff and seepage from waste dumps or seepage from process tailings; do not necessarily reflect the long term potential for AMD. The ultimate quality of mine drainage is a function of the interaction of many chemical, physical, biological and engineering (operational) factors. Techniques are available that can predict the qualitative nature of acid generation and mine drainage quality but accurate quantitative predictions are essentially impossible at the present time. As more and more mining operations exploit sulphide ore, the AMD and acid waste issue will become a. far greater concern. The significance of time dependent factors in the production of acid mine drainage-.is not just restricted to particuL.ar mine sites but needs to be recognised by the mining industry as a whole.

Jan 1, 1988

The word "optimization", refers to the search of an economic optimum, or, more precisely, to the choice of technical parameters which will define the more profitable mining project, knowing the values of the economic parameters. In fact, there is no direct way to perform this optimization, because the extremely large number of technical factors involved, from the type of working and its selectivity to the characteristics of the mill and its flexibility, makes it impossible to make a comprehensive survey of all possible projects. Beside, it would be meaningless to engage in such a task as the deposits themselves are not really known, but only estimated, with sometimes a high level of imprecision. Not to mention the numerical instability which would affect such a computation! In addition, the "best" project is not necessarily the one which strictly maximizes a given profit formula. There also exist human factors which have to be complied with, when choosing the cutoff grades for instance. Finally, there are other non-numerical factors which interfere with the choice between several projects: the shape of the bottom of a pit of the layout of the access road for instance.

Jan 1, 1986

By Aspinall T. O

Draglines have found wide application in strip mining coal seams down to 60m depth. A research Project funded through NERDDC has been underway during the past two years investigating the application of large draglines loading overburden into hoppers feeding into conveyor systems or off-highway trucks. This paper presents the preliminary results of these investigations and covers overburden characteristics, bucket spotting con- trol, bucket design, conceptual hopper systems, system application at representative mine sites, and broad process comparison. The studies have initiated new concepts in the extended use of draglines at deeper strip- ping depths. Alternate arrangements for dragline bucket rigging and bucket control aspects of dragline stripping operations offer productivity improvements. Extended use of existing draglines includes, draglines dumping into hoppers which feed large trucks or conveyors, trigger dump buckets rigging arrangements, and rear dump dragline buckets with integral grizzly bars. The paper details these suggestions, and points to specific areas where the most productive applied research is anticipated. Mine planning considerations detail the factors involved in selecting dragline bench heights in association with hopper operations.

Jan 1, 1989