Search Documents

By Mei-Yan Yang, Qiu-Ying Wang, Ltd. Yunnan Yuntong Zinc Co., Guo-Mu Chen, Meng-Yang Huang, Peng Zeng, Guo-Feng Li

"Historically, alot of jarosite was found in the leaching residue when leaching indium from secondary zinc oxide materials. The reasons for the formation of indium bearing jarosite were theoretically analyzed. The influence of controlling the acidity and the addition of reagents on the indium leaching yield during secondary zinc oxide processing was investigated. In order to increase the leaching yield of indium, a measure of controlling the creation and destruction of jarosite was proposed. The production data shows that the leaching yield of indium was increased from 60 to 96%, and the content of indium in leaching residue simultaneously decreased from 900g/t to 100–200g/t when implementing such controlling measures.INTRODUCTIONIndium does not occur as independent minerals in the earth’s crust and is mainly associated with complex sulphide minerals. Specifically some sphalerites can contain as much as 900g/t of indium. Most indium is recovered from by-products of copper, lead or zinc metallurgy. Therefore, the research on the recovery of by-products in non-ferrous metallurgy is important(Sinclair et al, 2006). The main technologies used for this objective in China include: •,pre-neutralization-reduction-precipitation indium process(Yu et al, 2008), •,countercurrent oxidizing acid leaching process and sulphation roasting-water leaching process(Cao, 2005), •,oxygen pressure acid leaching of zinc concentrate-P204 extraction process(Yang et al, 2006), •,doubleacid leaching-solvent extraction process on lead dross from a reverbatory furnace flue dust(Liu, 2003),•,an acid leaching-solvent extraction process on smelting ash(Zhouet al, 2005). Although high pressure and extreme conditions can be used to improve extraction from high iron bearing indium residues(autoclave processing), mild extraction with lower cost and lower environmental impact are preferred.This paper describes both how the indium extraction using mild conditions in a secondary zinc circuit was quite low and, how through XRD and chemical analysis jarosite formation was found as the main cause. The paper then proceeds to discuss a method for improving the leaching yield and the application of this method in industrial practice."

Jan 1, 2016

By T. Sun, J. Kou, C. Sun, China Railway Resources Group Limited

"The polymetallic sulfide ore in Jiama county of Tibet contains 0.78% Cu, 0.046% Mo, 0.31 g/t Au and 17.9 g/t Ag in average. However, heavy loss of valuable metals was observed using high-pH process and Butyl xanthate as the collector. In this paper, the flotation was optimized through the adoption of a novel collector C-7, which is a mixture of xanthate ester and thionocarbamate. This collector showed better flotation performance under weak base conditions. The recoveries of Cu, Mo, Au and Ag increased to 93.24%, 84.60%, 78.13% and 75.41%, respectively, under 15 g/t of C-7 at pH of 8.0. The adsorption mechanism of C-7 was investigated by micro-flotation tests, zeta potential measurements, FTIR analysis and adsorption quantity measurements. Chemisorption of C-7 on chalcopyrite surface is demonstrated with adsorption density 3.8 times higher than on pyrite.INTRODUCTIONXanthates are the most commonly used collectors of strong collecting ability for separating copper sulfide minerals from gangue in froth flotation. However, the selectivity of xanthates themselves is poor to realize separation of chalcopyrite and pyrite whose floatability are quite similar (Heyes & Trahar, 1977; Chandraprabha, Natarajan, & Modak, 2004). High pH process with xanthates as collectors is proved effective in copper-sulfur separation and is widely used in treatment of copper sulfide ore flotation (Smith, 1996; Valdivieso, Cervantes, Song, Cabrera, & Laskowski, 2004). This method could get ideal separation results, but large amount of lime must be added, and could bring about increased cost, device corrosion and environmental pollution. In addition, there could also be high depression and heavy loss of associated noble metal such as Mo, Au and Ag. Consequently, a large amount of research has been conducted on substitutions of xanthates for selective flotation of copper sulfide ores under low pH conditions (Gholivand, Khodadadian, & Ahmadi, 2010; Li, 2010)."

Jan 1, 2016

By L. Cheng, Y. W. Pan, Y. R. Liu

"Impounding deformation of slope and foundation is significant during and post dam construction. Reservoir impoundment is accompanied with various phenomena, including material degradation, effective stress decreasing and buoyancy in rock masses. These phenomena are related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope, which finally led to failure and landslide. Pore pressure in jointed rock masses is considered in constitutive relation. The expression of effective stress for porous rock with fluids is incorporated into the Drucker-Prager criterion. Based on monitoring data of valley width and dam deformation, the effective stress law is applied to analyse the impounding influence of slope and foundation to Jinping-I high arch dam. The dam is accompanied with complicated topographical and geological conditions. The results show that calculated and monitored values agree well, and the application of effective stress law provides an approach to evaluate dam deformation, stress and stability with impounding effect considered.INTRODUCTIONImpounding deformation of slope and foundation is a common and significant problem during dam construction and operation. This phenomenon exists in a lot of reservoirs in China, like Laxiwa, Ertan, Xiluodu and Jinping-I arch dams, and some dams in Europe. It is related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope. Monitored data indicates that the valley width tends to shrink in hydraulic engineering during the impounding process, which will change the stress and deformation of dam and abutment. Therefore, global stability of dam and foundation should be evaluated with impounding process taken into consideration."

Jan 1, 2015

By E. De Souza

Energy associated with ventilating an underground operation comprises a significant portion of a mine operation's base energy demand and is consequently responsible for a large percentage of the total operating costs. Ventilation systems may account from 25?40% of the total energy costs and 40?50% of the energy consumption of a mine operation. Fans are the most important mechanical devices used to ventilate underground mines and the total fan power installed in a single mine operation can easily exceed 10,000 kW. Investigations of a number of mine main fan installations have determined their assemblage to be, in general, very energy inefficient. The author has found that 40?80% of the energy consumed by a main fan is used to overcome the resistance of fan assemblage components. This paper presents how engineering design principles can be applied to improve the performance and efficiency of fan installations, resulting in substantial reductions in power consumption, operating cost and greenhouse gas emissions. A detailed case study is presented to demonstrate that, by designing fan assemblages using proper engineering concepts of fluid physics and industrial ventilation design, main fan systems will operate at efficiencies well above 80?90% (compared to common operating efficiencies of between 20 and 65%), resulting in a drastic reduction in a mine's overall costs and base electrical and energy loads.

Aug 1, 2013

By Niraj Bala

Boiler tubes of coal-fired boilers suffer severe erosion-corrosion (E-C). One method to counteract this problem is by the use of therma, spray protective coatings. Cold spray coating process was used to deposit Ni-20Cr powder on SA 516 (Grade 70) boiler steel. The bare as wel, as the coated steels were subjected to cyclic experimenta, studies, in the superheater zone of a coa, fired boiler. The weight change technique was used to establish kinetics of the erosion-corrosion. XRD, FE-SEM/EDS and X-ray mapping techniques were used to analyse the as-sprayed and corroded specimens.

Jan 1, 2010

By S. Banisi, A. Haji-Zadeh, A. R. Hasankhoei, M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9m × 2.05m AG (Autogenous) mills (fixed speed) are used in parallel in a dry operation. The test works conducted in a scale down mill with a diameter of 1m indicated that conventionally used "deflector" type liners did not provide efficient environment for grinding. In this research, to improve the grinding efficiency, a new design using low profile end liners incorporating radial ribs of proper height was investigated. In order to determine an appropriate liner design at different operating conditions, a 100cm×10.8cm model mill was used for experimentation. The special design of model mill made it possible to increase the radial ribs height in steps of 6mm up to 18.5mm. The transparent end of the mill enabled accurate trajectory determination by image analysis. The results indicated that the new lower height profile deflectors and 15.5mm-height (14.5cm in industrial scale) radial ribs improved the mill performance while avoiding excessive pressure drop across the mill and wear on the liner. The image analysis showed that the use of new liners increased the distribution of coarse particles across the mill cross section from 28% to 35%. A new liner design was proposed by decreasing the number of liners in each slice from 5 to 4 pieces. The thickness of the inner head liners reduced from 45cm to 30cm and the outer deflector liners replaced by radial ribs. The distance between the feed and discharge inner head liners increased from the original 115cm to 145cm which increased the effective length of the mill by 26%. The new design reduced the weight and volume of end liners by 9% and 23%, respectively. It was predicted that the new liners design increases the mill throughput by 10% and reduces the metal consumption by 20%.

Jan 1, 2016

By Brad Bjornson, Geoff Stevens, Mike Ashar, Cliff Britch

"LocationThe facilities are located 30 km north of Fort McMurray, Alberta (or 470 km northeast of Edmonton, Alberta).Brief Description of OperationThe operation includes the mining of oil sands, extraction of bitumen from the oil sands, and upgrading of the hydrocarbon fraction prior to shipment via pipelines to refineries.HistorySuncor was initially called Great Canadian Oil Sands. It was started by Sun Oil of Philadelphia. Construction began in 1965, with the first production coming on September 1967.Details of Present Milling Practice (Plant 3)Plant 3 recovers bitumen from the oil sand using the Clark hot water process. The basic steps in the process are conditioning, primary recovery, secondary recovery and tailings oil recovery.Oil Sand Feed SystemThe oil sand feed from the mine is transferred to the feed bin in extraction by two conveyor systems. Oil sand analyzers on each conveyor system measure the amount of bitumen and fines in the ore. Cones at the bottom of the feed bin distribute the oil sand to five process lines. Feed flow from each cone is regulated by an apron feeder which transfers the oil sand to conveyors that discharge into the conditioning drums. Weightometers on each of these five conveyors measure the rate at which the oil sand is delivered into the drums. The oil sand feed rate to each drum can be adjusted by varying the speed of the apron feeders."

Jan 1, 2000

By Michael S. Moats, Alex Luyima, Tomas Oliveira

Some commercial copper electrowinning facilities use Cyquest N-900 (a polyacrylamide) or HydroStar (a modified polysaccharide) to improve the density and smoothness of copper electrodeposits. However, the effects of these additives have not been studied extensively in the open literature. Thus, the electrodeposition of copper at 40 oC from a non-stirred synthetic electrowinning electrolyte (40 g/L Cu2+, 160 g/L H2SO4, and 20 mg/L Cl-) in the presence of various concentrations of either additive was evaluated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). CV results show that neither additive has much effect on the nucleation overpotential of copper electrodeposition on stainless steel. However, Cyquest N-900 polarized the copper deposition reaction upon the return sweep. The EIS data indicates that Cyquest N-900 increases the reaction’s charge transfer resistance and creates a second low frequency loop. HydroStar had minimal effect on the electrochemical data generated by CV or EIS. Thus, the mechanism by which HydroStar affects the copper deposition reaction still needs to be determined.

Jan 1, 2014

By Maureen Jensen

For mining companies looking to establish a strong North American presence, raise their profile or finance and position themselves for future growth, there is no other destination in the world that can offer a mining company the same opportunities as Canada whether you are an established blue chip or promising junior. Despite historically poor world commodity markets and shaky investor sentiment towards junior explorers caused in part by fallout from the high profile Bre-X fraud, Canada continues to shine as the undisputed mining finance capital of the world. Our natural riches and mining history go a long way to explain Canada's international prominence in mining finance. Canada has actively created and maintained one of the most integrated national frameworks to support mining ventures of all kinds. Our diverse industry, from one-person grass-roots explorers to mining industry giants, is one of our main strengths whether your company is Canada-focused or internationally active. The mining industry continues to be a vital contributor to the Canadian economy, contributing $26.2 billion in 1997 or 3.8% of national GDP, and is the second largest earner of foreign exchange. Industrial mineral companies are a very important part of this strength. These companies require a continuing access to capital to ensure that they can continue to compete and the globalisation of the Canadian mining industry has affected this industry just as much as it has affected every other industry in Canada.

Jan 1, 2001

By Y. Jiang, B. Li, R. Liu

"In this study, laboratory flow tests were conducted on 2-D artificial rock fracture network models containing a single intersection constituted by two inlet and two outlet branches. Three models with different intersecting angles of 60°, 90° and 120° were tested using both dye solution and distilled water. Constant flow rates were imposed on one inlet, and the flow patterns in the fracture intersections were captured by using a CCD camera. The test results were compared with the predictions made by numerical simulations that solved the Navier-Stokes equations. The results revealed that when Reynolds number (Re) is as low as less than 1, the intersecting angle has negligible influence on the flow rate of each branch and the flow patterns within a fracture intersection. As the interesting angle ? and Re (e.g., from 10 to 200) change, the normalized flow rates of different outlet branches change significantly, due to the inertial effect of fluid flow. These changes could be represented by a series of mathematical expressions involving Re and ?, which could be applied to fracture network models to improve their prediction accuracy on hydraulic properties (e.g., permeability and breakthrough curves of particles) of rock masses. INTRODUCTIONCoupled stress, flow, heat and mass transport are the corner stone subjects for many geoscience and geo-engineering disciplines, such as geological disposal of radioactive waste and geothermal energy exploitation. Many outstanding issues need to be investigated to enhance the knowledge on these subjects, and specifically more in-depth research in testing and modeling of the fluid flow in fractured rock masses is needed. In recent years, discrete fracture network (DFN) models have been extensively used to study the fluid flow and mass transport behaviors of fractured rock masses (e.g., Min et al., 2004; Zhao et al., 2011). In these models, each fracture is usually represented by a parallel-plate model, in which fluid flow exactly follows the cubic law. Therefore, comparative flow rate in each outlet branch of an intersection in these models only depends on its aperture. In reality, due to the surface roughness of fractures, the magnitude of mechanical aperture is usually larger than that of the hydraulic aperture of each fracture (Li et al., 2008; Xiong et al., 2011), and abundant flow patterns could exist in an intersection, influenced by its geometry, varying with changing Reynolds number (Re) (Kosakoswski & Berkowitz, 1999). Recent studies have also revealed that different mixing patterns might exist at a fracture intersection, bounded between streamline routing model and complete mixing model, that determine the final distribution of solutes in fractured rock masses (Johnson and Brown, 2001; Park et al., 2001). Numerical simulation has been the principal method adopted in previous studies, and the studies conducting flow tests on intersected fractures are less reported (Wilson & Witherspoon, 1976; Johnson and Brown, 2001). In this study, laboratory flow tests and numerical simulations by solving the Navier-Stokes equations were conducted on 2-D models containing a single intersection constituted by two inlet and two outlet branches, intersected at different angles. The main objective is to study the influence of intersecting angle on the flow behavior of the intersected fractures and the variations of flow patterns and fluid redistribution in each model along with the changes of the Re and the intersecting angle ?. The influence of surface roughness was not considered."

Jan 1, 2015

By S. J. Cook

The subject of capital and the Canadian mining industry is so broad as to be impossible of comprehensive treatment in brief form. The purpose of the present paper therefore will be only to outline in a meagre and somewhat sketchy way the nature and extent of the mineral industry in Canada and to point out those features which are likely to be of general public interest. Canada's mineral industry has a long and creditable production record. The? value of the output per capita rose from $2.23 in 1886 to a maximum of $26.40 in 1920 and the value of the products from ten million dollars in the former year to almost two hundred and twenty-eight million dollars in 1920. Compared with other primary industries and on the basis of the value of production, mining held third place in Canada in 1920, the premier position going to agriculture and the value of forestry production placing that industry second in the list. In the mineral industry, between six and seven thousand properties are operated annually giving employment to up- wards of sixty thousand employees to whom about seventy-five million dollars is paid in salaries and wages. During 1923, seventeen mineral products reached a production value of one million dollars or over in Canada and in order of the values assigned these were: coal, gold, nickel, cement, cop-per, silver, clay products, lead, asbestos, natural gas, stone, zinc, lime, cobalt, sand and gravel, gypsum and salt.

Jan 1, 1924

By A. Golpaygan

Application of Computational Fluid Dynamics (CFD) modeling for simulation of fluid flow and combustion in industrial scale electric furnace is presented. Poor combustion efficiency, roof and/or side wall overheating, carry over to off-gas system and non-ideal radiative heat transfer to processes or cooling systems have been common limiting factors causing inadequate process performance of the furnace, operational problems, and safety hazards. This paper describes how CFD analysis can be used to obtain a better understanding of commonly observed problems associated with freeboard combustion. Examples are presented to describe using combustion CFD modeling to understand requirements to diagnose a problem with furnace design including required freeboard volume or possible roof/side wall overheating.

Jan 1, 2011

By D. Song

In this paper, the differential equations governing the mass transport and the electrochemical reaction in a cathode catalyst layer of polymer electrolyte membrane fuel cells are solved based on the polynomial series expansion method. Explicit expressions for the polarization curve as well as for the distributions of oxygen, current density and overpotential are obtained when a quadratic, cubic or quartic polynomial is employed to approximate the oxygen concentration distribution. These kinds of explicit solutions are desirable for MEA design and diagnosis purposes. The comparison between the conventional numerical approach and the explicit solution approach proposed here shows that satisfactory accuracy can be reached by the first four terms of the polynomial series. The effect of the catalyst layer thickness on the accuracy of the obtained explicit polynomial solutions is also discussed.

Jan 1, 2005

By R. K. Singhal

"On the mining side the Canadian oil sands industry has become proficient in excavation and disposal of ore and overburden. Nearly twenty years of mining experience is now behind this industry. While local improvements to existing mining systems and practices will continue, it is believed that some further gains in productivity can be achieved by selectively introducing new ideas from other mining and non-mining industries. This type of technology transfer is vital for over-all cost-effective technology enhancement of oil sands mining operations.Discussed in this paper are the issues of mining equipment, equipment sizing, microprocessor and computer based technol¬ogy as applied to mine-wide data management, automation and remote control and a projection of likely mining systems in the year 2000!This paper reviews the ""state-of-the-art"" in selected surface mining systems and attempts to evaluate the forthcoming technology and its application."

Jan 1, 1989

By Erwin L. Zodrow

THE AUTHORS welcome this timely opportunity to comment o n a paper by MacLean and Merner (" Room-and- Pillar Mining at the Prince Mine of the Cape Breton Development Corporation " , ClM Bulletin , June 1978, pp. 59-62) concerning the rock falls and their relation to "a change in the strata". First, however, it is proper to express our gratitude to the Cape Breton Development Corporation, and in particular to A. R. MacLean, for making it possible for us at the College of Cape Breton to start two new collections. The first of these is a fossil plant reference collection from the Sydney Coalfield, Cape Breton (Upper Carboniferous period) , and the second is a documentation of the role o f pyrite in the formation of hydrated sulphates (samples from No. 26 Colliery, 1-B Mine, and the Prince Mine at Point Aconi). Conditions of sedimentation in the deltaic-type basin of the Upper Carboniferous time in the Point Aconi area were such that on the (coal) swamp, now represented by the Stubbart (or Hub) seam , (a) clays of varying thickness and extent were deposited , (b) biogenetic sulphur was introduced and (c) flora were buried. These are essentially the culprit s that make rock falls possible and at the same time predictable over large areas (in the present mine). The clays lithified to become shale, and biogenetic sulphur combined with iron to become pyrite (marcasite?), which exists as nodules and in fine-grained layers.

Jan 1, 1978

Adsorption of guar gum was investigated on model minerals typically found in water-insoluble slimes of potash ores. The ionic strength of the adsorption mixtures was varied from distilled water to saturated NaC1 and KC1. The tests were also performed using a saturated brine. The adsorption density of guar gum on illite, dolomite, and kaolinite was found to be not only a function of total ionic strength but also of the type of electrolyte present in solution. Generally, the adsorption of the polymer on the clay minerals was higher in KC1 solutions than in NaCI, but the differences gradually disappeared when the electrolyte concentration approached saturation. The results were analyzed in terms of chaotropic (K ) or kosmotropic (Na') properties of background counter-ions and their different behaviors at the hydrated mineral-water interface. Guar gum adsorption on dolomite was related to the presence of calcium and magnesium sites on the mineral surface, and to the cis-configuration of OH groups of mannose units. Based on viscosity measurements, it was suggested that guar gum macromolecules form entanglements in NaCI solutions (and distilled water), but individual molecules exist in KC1 solutions thus creating different modes of adsorption of guar gum from concentrated NaCl and KCl solutions.

Jan 1, 2006

By M. Bryson, A. E. Brady, W. Dawes, G. Beer, N. Sehlotho

Mkango Resources Limited is developing the Songwe Hill Rare Earth Element Project in southeast Malawi. Since being awarded the exclusive exploration licence for the project in January 2010, Mkango has completed an extensive work programme including detailed mineralogical studies, geological mapping, geochemical sampling and trenching, environmental and social studies, two phases of diamond drilling, and extensive metallurgical test work. In October 2012, the company announced a NI 43-101 compliant mineral resource estimate comprising an Indicated resource of 13.2 million tonnes grading 1.62% total rare earth oxides (TREO) and an Inferred resource of 18.6 million tonnes grading 1.38% TREO. The Indicated mineral resource estimate formed the basis for commencement of the Preliminary Feasibility Study (PFS). The mineralogical program identified the fluorocarbonate mineral, synchysite, and the phosphate mineral, apatite, as the primary rare earth element (REE) bearing minerals. Extensive flotation testwork conducted at Mintek in South Africa has resulted in an effective regime to increase the REO grade 2.6 times. Initial leaching testwork by Mintek identified that a selective hydrochloric acid (HCl) leach can target the gangue minerals with minimal REE dissolution. Recent testwork undertaken at Nagrom in Western Australia has expanded on this work to develop a two stage HCl leach process incorporating HCl recycling. A downstream processing route of purification and cerium rejection to produce a cerium depleted high grade REE concentrate suitable as feed to a separation facility is proposed.

Jan 1, 2014

By T. Lamb

There are many honor stories about aluminum in the marine environment and many are not based on facts, so they are myths. Myths must be addressed before progress can be made. This paper attempts to dispel the myths and state the facts. A common perception is that aluminum ships cost significantly more than steel ships. This paper illustrates that even though the cost of the aluminum structure is over 50% more than the steel structure, an "equivalent" aluminum naval ship can be built within 7% of the acquisition price of a steel ship. This is possible because of the cascading benefits of the aluminum ship's significantly lighter weight. Aluminum ships also have a life-cycle cost advantage over steel ships because of reduced maintenance and fuel cost savings.

Jan 1, 2011

By E. Brouillette

Difficult operating and mining conditions such as low visibility, difficult roadbeds, fast cycling, small openings, and sharp corners create high demand for LHD manoeuvrability and operator dexterity. Operator experience and patience is especially solicited to fill the bucket rapidly and efficiently and performance can be particularly affected by the skill level of individual operators. Teleoperation and automated loading are viewed as options to improve overall equipment and operation performance in certain mining conditions. Comparative statistical measurements of autoloading performance in different production environments at Noranda demonstrate an increase in bucket filling efficiency and a reduction in filling variance, allowing LHD operation to be more consistent and within manufacturer specifications. Consequential cost savings and productivity increases are demonstrated to be transferable to other mining situations.

May 1, 2003

By Gilles Tremblay

The legacy of orphaned/abandoned mines, with their associated environmental liability, human health concerns and the financial costs of clean up is a serious issue facing Canada. In 1999 and 2000, a number of stakeholders put forth requests to Mines Ministers to establish a joint industry-government working group, assisted by other stakeholders to review the issue of abandoned mines. The Ministers supported this initiative and asked that a multi-stakeholder workshop be organized to identify key issues and priorities. The Workshop on Abandoned Mines, held June 2001 in Winnipeg, developed consensus, guiding principles and recommendations that were presented at the Mines Ministers? Conference, September 2001. Ministers agreed on the importance of a large-scale program for the rehabilitation of orphaned/abandoned mines sites. A multi-stakeholder Orphaned/Abandoned (O/A) Mines Advisory Committee was formed and a plan was developed to study various issues relating to the implementation of remediation programs across Canada. Three task groups were formed to address the following key areas: Information Gathering; Community Involvement; and Barriers to Collaboration. The presentation will include a summary of the results of the three projects and the future work plan for the program.

Nov 1, 2002