Search Documents

By G. Bonin, R. P. Preston

"This paper presents a series of case studies where spherical camera photographs were used to generate 3D shaft models using photogrammetric methods. The shaft models were, checked for accuracy by comparing them to overlapping laser scan data, provided survey data or idealized shaft models. Short lengths of model were found to more accurately reproduce the shaft surface, with a best observed accuracy of 8 mm. Longer models encountered errors with accumulated errors as exhibited by slight deviations from vertical or slightly conical model shape. At present, the models are considered acceptable for general documentation and gross change detection. INTRODUCTION Shaft inspections are required by mining regulations in many jurisdictions and are commonly completed by trained mine personnel via visual inspections. This can be time consuming and prone to errors due to lapses in attention and the rapid travel rate required to inspect an entire shaft in a reasonable amount of time. Similarly, because of the time requirements, there can be impacts on other aspects of mining as a result of occupying the shaft for inspections. Spherical cameras with supplemental light systems offer a modern addition or alternative to conventional inspections. These cameras can be lowered relatively quickly to collect high definition, fully illuminated videos of the shaft that can be reviewed in detail later while the shaft returns to service (Gillis et.al., 2019). The use of cameras offers a further opportunity for valuable survey data generation from the same original data stream. The video data can be processed into three-dimensional (3D) models using Structure-from-Motion (Westoby et al., 2012) based photogrammetric methods. Depending on the quality of the source video and availability of survey control (required for all photogrammetry models) these models can be very accurate. Shaft surveying can be conducted with traditional theodolite methods but such surveys are time consuming and limited in their data density. Similarly, scans can be completed using conventional terrestrial laser scanners, but this requires a significant number of distinct setups to provide sufficient overlap between scans. Work is being conducted both on the laser scanning (SLAM, Durrant-Whyte & Bailey, 2006) and photogrammetry fronts towards kinetic scanning (Benecke, 2017) systems. The major advancement which is permitting these kinetic systems is Inertial Measurement Units (IMUs) which can provide localization in GPS denied environments and reduce errors associated with the open traverse format associated with shaft scanning."

Jan 1, 2019

By M. Behrouz

Thermal power plants convert thermal energy due to nuclear reactions or the combustion of coal, gas, heavy oil, or some other hydrocarbon to electrical energy. They consist of a variety of equipment, such as boilers, turbines, generators, cooling towers, and auxiliary equipment. Any factor that affects the equipment efficiency affects the overall efficiency. Analysis of the cooling tower and raw water using the Langlier Saturation and Ryznar Stability Indices showed that the cooling water at Sarchesmeh was slightly scaling with respect to silica. Cold lime softening was found to be a cost-effective method to produce cooling water with adequate properties to reduce the cooling water make up from 85 to 70 m3/h and blow down rate from 35 to 20 m3/h.

Jan 1, 2007

By George S. Rice

Foreword Explosion hazards differ widely in the mines of different fields or coal basins. They also differ as between different mines in the same basin or fold, because of variations in gas entering the mines, and because dust conditions and explosion hazards are affected by the mining methods employed and the organization of the work. It is unquestionably true, however, that there are greater differences in explosion hazards in mines of different coal fields or basins than between different mines of the same field or basin. In these respects, the coal fields and individual mines in Alberta are not exceptional. The same conditions obtain in various countries where coal is mined, and are found in single States, as for example in Colorado, where coals are mined ranging in character from sub-bituminous to anthracite, and in attitude from flat horizontal to steeply pitching beds. The U.S. Bureau of Mines, at its experimental mine near Pittsburgh, Pa., has made large-scale tests of the relative explosibility of dusts of coals, ranging in rank from Wyoming sub-bituminous coal containing 19 per cent moisture, to anthracite from Pennsylvania, and including samples from a mine in the Crowsnest Pass district, B.C., and from a Vancouver Island mine. The Bureau has also made similar tests of the dust of coal from a Yorkshire mine which the British Safety-in-Mines Research Board uses as standard.

Jan 1, 1927

By Paul Hammond

Abstract The Allard Lake ilmenite deposits, which are currently being developed on a large scale, occur as a series of dykes or lenticular, flat-lying bodies within the northeastern part of a large, oval shaped anorthosire mass of Precarnbrian age which lies with its long axis paralleling the gulf of St. Lawrence. The Lac Tio deposit, discovered by Kennco Explorations, Limited, in 1946, is the largest body of titanium ore of its type now known in the world. It contains upwards of 112,000,000 short tons of ilmenite ore averaging 32 per cent TiO2 and 36 per cent Fe. The ore is an aggregate of ilmenite with oriented microscopic blades of hematite. The deposits appear to be high temperature, late magmatic injections containing only a small amount of volatiles, and bear a genetic relationship to the anorthosite rocks in which they occur. * * * Introduction Recent developments on the ilmenite deposits in the Allard Lake district of Quebec indicate the probability of a major industry, and one which may make Canada the world's greatest producer of titanium pigments and, ultimately, of titanium metal. The presence of ilmenite in this district was first reported by the Quebec Department of Mines following a reconnaissance shore-line geological survey in the year 1941. The ensuing report by Retty describes the occurrence of a number of small ilmenite lenses about the shore of Allard lake and' along two smaller lakes in the vicinity. These showings were later staked by Toronto and Montreal interests who carried out a certain amount of development work, and were described in more detail by Longley for the Quebec Department of Mines. The claim groups were later optioned by Kennco Explorations, Limited, Canadian subsidiary of Kennecott Copper. None of the deposits in themselves constituted a sufficiently large body of ore to warrant the major construction expenditures necessary for their exploitation on a profitable basis. The surrounding anorthosite areas, however, were considered favourable for the possible occurrence of other ilmenite deposits

Jan 1, 1949

By A. McGrath, M. Trovant, M. Haque

Minimizing energy consumption is a priority for many industrial facilities. Metallurgical and gasification processes produce dirty syngas (CO and H2), which offers the potential for energy recovery. However, syngas handling can pose an explosion risk and even minor leaks can result in poor workplace hygiene. Furthermore, many jurisdictions around the world now discourage wet syngas handling due to limited water availability and secondary pollution. Hatch has developed a 100% positive pressure gas handling system that targets these safety hazards without using fresh water. The implementation of a system for calcium carbide smelters at Qinghai Salt Lake Industry Co. (QSLIC) in China is profiled as a case study.

Jan 1, 2015

By W G. Brese

The attention of the world is being focused on the spectacular rise of elemental sulphur production in Alberta. In the short space of a decade, production has increased from less than 10,000 long tons, in 1952, to al-most 1,000,000 long tons in 1962. Moreover, 1963 sulphur production is expected to rise by 50 per cent to approximately 1,500,000 long tons, and further increases are forecast for ensuing years. The reason for this dramatic in-crease in elemental sulphur production, particularly in the last year or two, is that Alberta elemental sulphur is recovered in association with the production of sour natural gas. When very large volumes of natural gas began moving to U.S. markets in the latter part of 1961, the resultant increase in sour gas production led to a marked increase in the production of sulphur. Consequently, Canada, mainly on the strength of sulphur produced in Alberta, will soon become the second largest producer of sulphur in the Free World

Jan 1, 1963

By G. Granata, C. Tokoro, M. Matsuoka, K. Horiuchi

"Given the high demand of copper and the lack of new high-grade deposits, low grade copper ores containing copper oxides and refractory sulfides need to be processed as well. However, in order to recover copper from refractory copper ores, the leaching performances should be improved. In this study, we investigated the effect of the mechanical activation in the leaching of copper from covellite. The influence of a mechanical treatment by planetary ball milling on leaching rate in sulfuric leaching media was evaluated by using X-ray diffraction (XRD), mineral liberation analysis (MLA) and X-ray absorption fine structure (XAFS). Results showed a significant increase in copper leaching from around 50%up to 100% along with an improvement of the leaching kinetics when using planetary ball milling. XRD spectra showed the disappearance of the covellite peak from (101) face, thus suggesting the amorphization of covellite associated with the use of planetary ball milling. XAFS results showed that the coordination number of Cu changed from 6 to 3, thereby confirming the effectiveness of the mechanochemical effect.INTRODUCTIONDuring the last decades, while the copper grade in copper ores has been decreasing, the concentration of impurities such as arsenic tends to increase, thus requiring for the processing of low grade copper ores. For a suitable processing of copper minerals, hydrometallurgical processes are preferable due to the lower costs, the lower environmental impact and the easier implementation (Watling, 2006). However, for an economical recovery of copper, the leaching performances must be improved.Among the recent advancements in leaching technologies, the mechanochemical activation allows for an improvement of the leaching performances by means of high-intensity grinding(Mohammadabad et al., 2016). In the first place, the improvement is the result of the dramatic decrease of particle size, which results in an increase of the mineral surface area and the consequent enhancement of leaching kinetics. Furthermore, the intense mechanical stress due to the high-intensity grinding could induce the rupture of the crystal structure producing a decrease of crystallinity. Such changes of the mineralogical structure, also known as mechanochemical effect, can lead to more leachable mineral, thereby resulting in a greater dissolution of copper. Last but not least, whereas the mineral surface might undergo passivation during leaching, the high-intensity grinding can continuously refresh the surface of the mineral, thus exposing portions of unleached bulk mineral."

Jan 1, 2017

By W. J. D. Stone

"For several years, the existence of a deposit of barite (BaS04) near Brookfield, Nova Scotia, has been known. A very large deposit of strontium (SrS04) near Sydney, Cape Breton, is a more recent discovery. Cape Chemical Syndicate has been formed to work the deposits. A five-million-dollar integrated mineral processing and chemical plant is planned for Sydney to produce various compounds of barium and strontium. The mineral processing plant includes the Jones Wet Magnetic Separator and will produce high-purity barite and celestite. These products will be processed further in the fine grinding plant and the chemical plant. The general project is described, covering the deposits, processing and markets."

Jan 1, 1969

By H. R. McCabe

"The study of a detailed series of structure and isopach maps of the Palaeozoic strata of southwestern Manitoba indicates that the principal Palaeozoic tectonic elements -the Williston Basin and Elk Point Basin -have been modified to a considerable extent by major tectonic features of the Precambrian basement. The principal basement feature is the break between the Churchill and Superior provinces, which coincides roughly with the Manitoba-Saskatchewan border. East-west-trending orogenic belts within the Superior crustal block may also be reflected to some extent in later Palaeozoic movements. In addition, the Superior crustal block, as a whole, appears to have had a slightly different response to the tectonic forces, giving rise to both basin subsidence and basin uplift. During periods of deposition, especially during Ordovician time, the Manitoba portion of the basin appears to have undergone a relatively higher rate of subsidence, whereas during periods of erosion relatively greater amounts of uplift and truncation have occurred. As a result, the depositional and erosional patterns for most of the Palaeozoic formations in southwestern Manitoba are somewhat anomalous relative to the regional basin framework.Some prominent Palaeozoic structures probably are the result of salt solution and differential compaction caused directly or indirectly by relatively minor tectonic movements related to Precambrian basement features. In particular, the prominent hinge line at the edge of the Devonian Prairie Evaporite salt basin may be due, in large part, to salt solution. Numerous other small structural lows, structural highs and isopach thicks, probably resulting from salt solution, occur along the salt edge and have been important in modifying and controlling Mississippian oil accumulation in the Daly-Virden producing area."

Jan 1, 1967

Pilot plants for pressure hydrometallurgy represent special design and project execution challenges unique to the industry and to the pilot- and demonstration-scale. Pilot plant projects have different objectives and shorter timescales than commercial plant projects. Design considerations and strategies, and project execution methods that meet the special needs of pilot plant projects, are discussed. Specific guidance is given for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical process equipment, and for the selection of materials of construction for pilot-scale equipment. The balance between the need for process similarity with future commercial operations and the realities of pilot-scale equipment is also discussed.

Jan 1, 2004

By J. K. Atherton

If the metals sector is to contribute successfully to sustainable consumption we must adopt principles and practices which address the entire life cycle of the materials we produce. Progress must be founded on a sense of shared responsibility for the resources we utilize and the materials we create - it is this integrated approach which lies at the heart of materials stewardship. Materials stewardship means mining and metals companies producing materials in a responsible manner and then working with others, beyond their site, to ensure that the downstream material flows and applications are managed properly to create maximum societal value. In September 2006 ICMM published 'Maximizing Value: Guidance on implementing materials stewardship in the minerals and metals value chain'. This document takes a practical view presenting structured guidance as well as good practice case studies. In the publication, materials stewardship is described in terms of the range of activities that can be undertaken to ensure that all parties work collectively toward the responsible use of metal and mineral resources. This paper introduces the materials stewardship concept as set out in `Maximizing Value' and describes the business case for implementation as well as the ICMM framework for promoting materials stewardship.

Jan 1, 2007

By E. A. Morris

It has been shown that Alberta oil-sands fluid coke can be effectively used to reduce SO2 to elemental sulphur while simultaneously producing sulphur-impregnated activated carbon (SlAC). In the capture of mercury from industrial flue gases, SIAC has proven to be a highly effective adsorbent material. The current research aims at developing an existing SlAC technology to meet the needs of copper smelters for mitigating both mercury and SO2 emissions, while making elemental sulphur as a co-product. The challenge behind this undertaking is that these flue gases generally contain percent levels of 02 and H20 vapour (2-12%). The focus of this study is therefore on the feasibility of reducing SO2 using fluid coke under copper smelter flue gas conditions, as well as the optimisation of SIAC properties for capturing vapour phase mercury. It is hypothesised that mercury capacity is strongly affected by the 02 potential of the activation gas due to changes in surface sulphur types arising from different reduced sulphur species. To verify this, gas chromatography is used to analyse the reaction products while XPS and XANES will be used to describe the nature of sulphur on the SlAC surface. CVAFS analysis of mercury capacity will finalise the hypothesis assessment. Preliminary results indicate that 02 at 5% does not play a significant role in SSA or pore development. As expected, increased residence time contributes to SO2 reduction and elemental S yield.

Jan 1, 2007

By S. Beskri, N. Geoffroy

When metallurgical plants are designed, a lot of consideration is almost always given to material selection and possible damage mechanisms. Materials engineers are generally involved and will strive to select optimal alloys or refractories for the design conditions. Once in operation however, things often change. Equipment is overstressed to increase production, corrosive leaks are not always promptly addressed, proper welding procedures are disregarded, etc. This paper describes various cases from the mining and metals industry where serious mishaps, associated consequences, and costs could have been avoided if simple and proactive steps had been taken. It also presents a strategy, based on safety reviews, to help predict and prevent damage to critical pieces of equipment.

Jan 1, 2015

By Thomas M. Ware

"MR. Chairman, our Honourable Minister, Mayor Cole, it is a pleasure for me to come here, and join with you in one of the largest industrial shows ever held in Saskatchewan.It is an honour to be asked to keynote your meeting, to help mark an early chapter of this new industry for Saskatchewan. God has placed in our hands a new resource for His man on earth. This store of potash, 350 million years in the making, offers a vital resource to help man support his advanced intellect for thousands of years. It is a gift so large we must all wonder at its purpose and our responsibilities in serving our fellow man with it.We who are here to plan and implement the development of this essential mineral resource enjoy a great -privilege; and we share a great responsibility -to see that the billions of tons of potash which have waited beneath these prairies for millions of years are widely and wisely used to nourish the earth through future millenniums.To know the true value of potash, to be able to bring forth this re-source from over 3,000 feet deep in the earth, to establish markets and develop its potential worldwide is all part of our great heritage from generations past. So I think it is fitting on this occasion that we reflect for a moment on this heritage, to help us assess the responsibilities of its future development."

Jan 1, 1966

By J. F. Henderson

Stable mining operations commenced in the Northwest Territories in 1933. Pitchblende from Great Bear lake and gold from the Yellowknife district are the main minerals produced. The value of pitchblende products produced from 1933 to 1941 was nearly $6; 000; 000; data on subsequent production are not available. The first gold was produced from the Con mine at Yellowknife in 1938. Other properties that later came into production include the Negus; Slave Lake; Thompson Lundmark; and Ptarmigan mines. The annual gold production reached $3; 862; 000 in 1942 but due to the war and consequent labour shortage fell to $333; 218 in 1945. The only producing mines at present (May; 1947) are the Con and Negus; but several promising properties are under development; including that of Giant Yellowknife Gold Mines where large tonnages of ore are being blocked out. With the reopening of former producing mines and new production from properties now being developed; gold production should rapidly increase and exceed its former peak within the next few years.

Jan 1, 1954

By K. Maruyama, T. Nagasaka, R. d. Chairaksa-Fujimoto, T. Miki

Electric arc furnace dust or EAF dust is considered as a hazardous waste but contains a significant amount of economically attractive non-ferrous metals especially zinc as zinc ferrite (ZnFe2O4) and zincite (ZnO). The hydrometallurgical process is one alternative choice because it has the advantage of low energy consumption. The leaching of ZnO from the dust is very easy. However, the complex major zinc compound in EAF dust is ZnFe2O4, which is very stable and insoluble in alkaline or acidic media under delicate conditions, and causes the low zinc recovery yield by hydrometallurgical process. Moreover, halogens and heavy metals in the dust are also problematic. In order to develop a new effective EAF dust treatment process, the authors have proposed "CaO addition process" as pre-dust treatment to transform all of ZnFe2O4 in the EAF dust to ZnO and Ca2Fe2O5. In this study, the selective zinc leaching from the CaO treated EAF dust with NaOH and NH4Cl solutions was carried out. The effect of temperature, reaction time and solute concentration were systematically investigated. All of zinc in CaO treated EAF dust was successfully leached into both solutions.

Jan 1, 2014

"Real-time, on-stream analysis of the metal content of process slurries is an essential prerequisite for process monitoring and advanced control of mineral processing circuits. On-stream X-Ray Fluorescence (XRF) sensors for base metal applications are available commercially and form the basis of many plant monitoring circuits. To date, these commercial technologies have been insufficiently sensitive to measure precious metals such as gold and platinum group elements, typically present at part-per-million (ppm) and sub ppm levels. CSIRO has developed a novel X-ray based technology, called UltraGold, which enables detection of gold in slurries on a real-time basis with a precision below 100 parts-per-billion. This technology is based on the use of advanced X-ray optics, extensive Monte Carlo computer modelling for analyser design, high accuracy X-ray spectrum fitting where the X-ray intensities are matrix corrected. In this paper, we will introduce this technology and discuss the results of a proof of principle study performed in the laboratory with plant slurries (tailings and concentrate) from an Australian beneficiation plant. Finally, we will discuss further planned improvements. As projected grades in (gold) mining around the world fall and several large-scale mines approach the limits of their economic reserves, this method can enable significantly reduced operating costs by rapid analysis to improve circuit efficiency and hence improve recovery significantly.INTRODUCTION This paper describes a study undertaken to explore the feasibility of applying CSIRO?s UltraGold XRF technology to the on-stream measurement of gold in process slurries. The provision of rapid, accurate information of gold grade in feed, tailings and concentrate streams would facilitate significantly improved process control and early detection of plant upsets, resulting in substantial cost-savings. CSIRO have patented X-ray fluorescence (XRF) techniques for the analysis of key elements in slurries present at part-per-million (ppm) and sub-ppm levels. Conventional, commercially available on-stream XRF instruments generally have detection limits in the tens of ppm range, precluding their use for analysis of elements like gold that are mined and processed at much lower concentrations."

Jan 1, 2017

By G. Avramovic-Cingara, H. J. McQueen

The microstructure of commercially pure aluminum was investigated by using polarized optical microscopy (POM), orientation imaging microscopy (OIM), and transmission electron microscopy (TEM) techniques. Specimens were deformed in torsion at 400°C and equivalent strain rate of 0.1 s-1, to various strains of 0.2, 0.5, 1, 4, and 6. The results indicate that POM can usefully reveal grain and subgrain structures over a large field in aluminum. TEM is most suitable to study dislocation substructure and evolution of subgrains. While TEM microscopy and OIM are capable of resolving individual subgrains, OIM can not reliably distinguish subgrains with small misorientations, particularly in samples with low strain. On the other hand, the OIM technique is very useful in the analysis of many regions surrounded by high, medium, and low angle boundaries (HAB, MAB, LAB). Various misorientation maps were studied using different data processing methods. The analysis revealed that the subgrain size is relatively insensitive to strain. The fraction of low LAB ( < 5°) decreased and HAB (>15°) increased conversely with increasing strain, whereas MAB (5-15°) remained stable. The development of an increasingly bimodal grain boundary misorientation distribution is consistent with the predominance of dynamic recovery (DRV) in the evolution of microstructure, combined with geometrical dynamic recrystallization (gDRX), now called grain-refining DRV.

Jan 1, 2006

By J. W. Scott, G. G. R. Falkenberg

"The Syncrude project is an integrated complex designed to mine, extract and upgrade bitumen from the Athabasca tar sands to produce 129,000 barrels per day of synthetic crude oil. This paper provides a brief general description of the location, history and geology of the tar sands and the overall organization and structure of the project. The major emphasis and the bulk of the detail presented deals with the extraction plant; a material handling and mineral processing installation designed to treat 312,000 tons per day of tar sand feed.History of the Tar SandsThe Athabasca tar sand deposit was recorded in 1788 by Peter Pond, however the first serious geological mapping and exploration did not begin until 1915. Little interest was taken in the deposits until the Second World War, when the governments of Canada and Alberta conducted an extensive exploration program. In addition a number of pilot plants were sponsored during the 1940 -1950 decade. The hot water separation process was successfully demonstrated on the pilot plant scale during 1948 -49, and was established commercially in 1967 in the G.C.O.S. plant. The Syncrude plant, due to come on stream in April 1978, also employs the hot water separation process."

Jan 1, 1978

By S. Ross, M. Mayhew

"Kirkland Lake Gold introduced battery equipped vehicles (BEVs) at the Macassa Mine in 2011. The fleet of underground BEV haulage trucks and loaders has grown over the years to over 30 units, the world’s largest, currently handling approximately 80% of the daily production tonnage. The inflow and outflow of air occur through a limited number of relatively small openings, which limits the air volume delivered to the underground workings. In addition to improving air quality, the reduced heat load generated by the BEV (when compared to diesel equipment) had a significant positive impact in the workplace. The use of BEV for material handling has enabled increases in production that would not have been possible using diesel equipment.INTRODUCTIONMacassa mine was developed as a track-drift access mine, with the most recent shaft (#3) sunk in 1986. A new mining complex, the South Mine Complex (SMC) was discovered below the 5025 foot elevation south of traditional mining areas, and the majority of mining now occurs in the SMC. The discovery of that zone has led to an internal ramp which is used to access the SMC and haul ore to #3 shaft.The amount of airflow that can be moved through the mine is limited by the existing infrastructure to surface. This amount was recently increased to near its practical maximum from 118 CMS (250 kCFM) to 151 CMS (320 kCFM).Both diesel and electric equipment are used at Macassa. Tethered Load-Haul-Dump Machines (LHDs) have been replaced with Battery Electric LHDs, due to their increased mobility and depth of the mine. Battery trucks continue to replace locomotives to transport both ore and waste to the shaft, as mining has transitioned from tracked levels to trackless level and haulage has transitioned from horizontal levels to an inclined ramp.EQUIPMENT FLEET AT MACASSAMost of the primary material movers utilized at Macassa Mine are battery operated. As the mine goes deeper the battery technology will continue to be critical to the success of the operations. With over 300,000 hours of proven operation success, the battery technology and equipment will continue to be a major part of Macassa’s future."

Jan 1, 2019