Search Documents

By H. R. Pierce

A gas well has a certain definite capacity to deliver gas from the gas sand through the producing string of pipe. This capacity depends upon the pressures in the sand; that is, a well will deliver gas at a rate of flow which is determined by the formation or "shut-inn pressure in the sand and the back pressure at the face of the sand in the well. The three factors, rate of flow, formation or "shut-in" pressure, and the back pressure, for a given well, can be written into a fundamental relation which is strictly applicable only to that well. This relation can be used to determine the capacity of the well to deliver gas from any formation pressure against any back pressure held at the f ace of the sand in the well. Studies have been made of the deliveries of 400 gas wells operating under different conditions of pressure, Most of the wells which have been studied are in Osage County, Okla.; however, several representative studies have been made on wells in southern Louisiana, southern Texas, the Texas Panhandle, and West Virginia.

Jan 1, 1929

By George L. Gates

The Bureau of Mines developed a rapid instrumental method of analyzing oil well scales containing primarily barium sulfate. After removal of oil and water by carbon disulfide) the scale was dissolved in strong hydrochloric acid. The cations, barium, calcium, strontium, magnesium, and iron, were determined with the flame photometer using the method of additions. Sulfate was deter-mined colorimetrically after separation by selective adsorption on an alumina column. Phosphate was determined colorimetrically and carbonate titrimetrically. The method was reasonably accurate, although iron and magnesium were found to have mutual interference.

Jan 1, 1965

By Ralph Husack, J. W. Eckerd, G. A. Brady

The effect of gamma radiation on Pennsylvania anthracite and on reactions between anthracite and other materials was studied using a shielded , selfcontained 23,000 - curie cobalt 60 source . When anthracite was exposed to air at 65° C the reaction with oxygen was greater in the presence of radiation. than in its absence . Although drop- shatter tests indicated that exposure to radiation decreased the resistance to breakage of anthracite , this evidence of structural weakening was not supported by the results of grindability or particle- size studies . Irradiation caused definite changes in the gases evolved from evacuated samples of anthracite ; the percentages of hydrogen and carbon dioxide were increased, and the methane concentration remained unchanged . Carbon monoxide was evolved only from the unirradiated samples . Electron paramagnetic resonance (EPR ) measurements indicated large differences between evacuated samples and those exposed to air . There was little or no difference between irradiated and unirradiated samples , except that the free- radical content of unirradiated samples of anthracite increased progressively with higher temperatures of evacuation , but in the case of irradiated samples , no such behavior was found . Attempts to produce carbon disulfide and calcium carbide by reacting anthracite with sulfur up to 120 ° C , and with calcium oxide up to 400 ° C , were unsuccessful .

Jan 1, 1964

By J. F. Barkley

At the request of several Federal agencies, tests were conducted on a relatively recent type of anthracite -burning equipment named the Anthratube. This device, rated at 130,000 B.t .u. per hour, was designed to burn Pea-size anthracite automatically for steam or hot-water house heating and for domes-tic hot -water supply. ACKNOWLEDGMENTS The helpful cooperation of the Anthracite Institute and the manufacturers of the equipment, Axeman-Anderson Co., Williamsport, Pa., is gratefully acknowledged.

Jan 1, 1953

By N. S. Dalal, V. Castranova, K. Van Dyke, V. Vallyathan, J. H. Kang

"We have reported previously that crushing or grinding crystalline silica results in the generation of silica-based radicals on the particulate surface and that these radicals can generate hydroxyl radicals in aqueous solution. Data in the present study indicate that freshly ground silica is more cytotoxic and is a more potent activator of alveolar macrophages than comparably sized aged silica. That is, compared to aged silica, fresh silica is 4.2-fold more potent in decreasing the membrane integrity of macro· phages; is 50% more potent in activating hydrogen peroxide secretion by macro· phages; and is 4.frfold more potent in stimulating cellular chemiluminescence. Prosil 28, an organosilane material, is an effective coating agent for fresh silica. It decreases the cytotoxicity of fresh silica by as much as 78% and decreases the ability of fresh silica to induce chemiluminescence from alveolar macrophages by 58%. The data suggest that surface radicals associated with freshly cleaved dust may be an important factor in the induction of pulmonary disease. Furthermore, treating dust with coating agents may substantially decrease toxicity. INTRODUCTIONThe U.S. Department of Labor estimates that over 1.25 million American workers may be exposed to crystalline silica and that nearly 60,000 may be at risk of developing some degree of occupational lung disease (Parkes, 1982; Peters, 1986). Occupations of concern include miners, stone quarry workers, sand and gravel workers, sandblasters, foundry workers, and glass workers. Acute silicosis is characterized by inflammation, alveolar lipoproteinosis, and the rapid development of respiratory disability (Banks, 1986). In contrast, chronic silicosis develops 20-40 yr after initial exposure and is characterized by the appearance of concentric hyalinized nodular lesions and the progressive development of dyspnea (Parkes, 1982; Ziskind et al., 1976)."

Mar 1, 1992

By Ludwig Schmidt

Investigations conducted by the Bureau of Dines pertaining to the reduction of evaporation losses of petroleum have shown that such losses may be reduced 70 to 80 per cent by the use of vapor-tight tanks equipped with vacuum and pressure relief valves, and vapor-tight thief hitches. Additional studies have shown that it is often economical to supplement this type of construction with other measures that will reduce evaporation losses still further. Water-cooling systems, insulation, and light colored paints are the measures most often used in connection with vapor-tight tanks. Painting with light colored paints probably is employed in the greater number of cases. On account of the cost of insulation, or of installing water cooling systems, the use of these methods are restricted to tanks containing gasoline or crude petroleum with a very large content of low-boiling fractions. The effect of cooling systems has been discussed in a previous report.2 In choosing paints for tanks many factors must be considered. Probably the three most important are cost, protective value, and color. Many companies have adopted a standard color for all of their tanks in this way they reduce the initial cost of paint by buying in large quantities. The tank farms of such companies usually have a neat appearance, resulting from the uniform painting of all tanks. This procedure also has advertising value. Unfortunately, most of the paints used to protect steel are of the darker colors, usually red or black. These colors accelerate the rate of evaporation. Several companies have solved this difficulty by using a dark colored metal-protective paint as a primer coat, and a paint of any desired color for the final coat. Special metal-protective primers to be used under light-colored cover coats have been placed on the market by several paint manufacturing companies.

Jan 1, 1925

By A. A. Bakewell

This information circular, which describes mining methods and practices at the Baguio Gold Mining Co., Philippine Islands, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs. Since January 1952, Baguio Gold Mining Co. has operated its rehabilitated mine and mill in the Baguio district. Postwar labor and supply costs are three or four times prewar costs, whereas ore tenor and tonnage are about the same. Ore reserves remain approximately the same, but deeper and more spreadout operations add to increasing costs. Recently the company has acquired an adjoining property, which may lengthen its life substantially. Costs and general operations are more or less typical of the district, which includes three other active gold mines. Gold ore mined in the district totals approximately 4,300 tons per day.

Jan 1, 1959

By R. D. Groves

Techniques were developed for preparing metallurgical-grade copper powder from industrially produced cement copper. Flotation was used for rejecting discrete gangue particles, acid leaching to remove residual iron and aluminum, hydrogen reduction to eliminate oxygen, sintering to consolidate the fine-sized copper, and grinding to obtain copper powder. Powders prepared from six different cement copper samples contained, in percent, 98.5 to 99.0 Cu, 0.10 to 0.05 Fe, 0.10 to 0.08 insoluble material and the remaining individual impurities less than 0.15 percent. The apparent density, flow characteristics, and other physical properties were suitable for powder metallurgy applications. An economic evaluation showed that this process was economically feasible. Processing costs appeared modest when considering that copper powder commands a price normally about 17.5 cents per pound over that of electrolytic copper.

Jan 1, 1971

By Mark Sheppard

This p aver is the second of a series recording the results of tests made at various quarries throughout the United States to determine, (1) the relation between the size gradation of feed to, and product from, primary crushers; (2) the particle shape of crushed product; (3) the differences in gradation and particle shape produced by different types of primary crushers; and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Primary crushing has received comparatively little attention in the technical literature in spite of the fact that the design of the whole crushing plant should be correlated to the performance of the primary crusher.

Jan 1, 1938

By D. Bienstock

A high-B.t.u, gas can be synthesized by the catalytic methanation of a mixture of 2.5 to 3 parts of hydrogen to 1 part of carbon monoxide, obtained in the gasification of coal, using a steel catalyst followed by Raney nickel in a hot-gas-recycle system. Conversion of 99 percent of the H2+CO yields a fuel gas with a heating value of 983 to 1130 B.t.u. per cubic foot containing 78 to 96 percent methane, no carbon monoxide, and very small amounts of unsaturated hydrocarbons. With the steel catalyst alone, conversions were 85 to 90 percent, giving a fuel gas of 810 to 868 B.t.u, per cubic foot, or 847 to 975 B.t.u. on a C02-free basis. INTRODUCTION In 1948 the U.S, marketed production of natural gas was 5.15 trillion cubic feet; by 1958 it had reached 11.0 trillion cubic feet, a rate of growth of 8 percent annually. 4 5 Although demand is expected to increase less rapidly, by 1966 it may reach 16 trillion cubic feet, based on an estimated 4.7 percent annual increase.6

Jan 1, 1961

By D. J. MacDonald

This U.S. Bureau of Mines report reviews published information on synthetic berlinite (AlP04) and suggests experimental conditions requisite for its production. Berlinite is a piezoelectric material with potential use as a substitute for quartz in the crystal oscillators, which are components of electronic and electroacoustic equipment. Information gathered here (mostly from published sources) includes historical background, physical properties, end-use applications, criteria of quality, and physio-chemical factors involved in berlinite crystal growth. It is concluded that growing large high-quality berlinite crystal would require high-purity starting materials in an autoclave equipped with a noncorrodible liner and operated with temperature control of ±O.OO5 ac over a range of 250 to 350 ac.

Jan 1, 1995

By S. J. Pearce

There are a number of methods for determining relatively small quantities of sulfur dioxide in air. However, those methods require fairly elaborate apparatus and laboratory facilities. Frequently in industrial hygiene surveys it is desirable to have a simple arrangement to obtain "on the spot" determinations. This has been accomplished for concentrations of sulfur dioxide of hygienic significance by using the midget impinger and decolorizing a starch-iodine solution.

Jan 1, 1948

By L. C. IlsLey

Minin,g Qr col-cu.ttint till:I chines are 1?;\i9ng the _m9t wideiy .used de1sses ()f mining equipment.· These 1T:.i:1Chines ,.--re practicaily t-tl\·operc1_ted eiyher_by compressed .iir or by electric. ·motors. According to &.ta• compiled _ from the 122. issue COAL CATALOG\JE. OJMEINED WITH; OOAL "FIELD 'pf!:fC'TOTl1, bf 7,088. mnes from which reports were obttiined there -are 3895 mines that u.se coal-cutting eql;lipmen:ts,, 'f'hi report lists 20,031: r.ct:lchines, 17,&75 being operated by·elct:i.c.m<;>_tors··:r;id :the remtiinder by compressed i.r motors,· ,-. · ', .. . · .. ··, .. _ ,· .,, .. .. . . . . . : ; "'l t:: On tl.Ccou-nt .. of the wide· use of coc:11-cutting -.:i"cliine_- any Stat!;ls have issued regulationa as "to their operation dnd be to safety precautions that.should be observed J especially in gaseous mines.

Oct 1, 1922

By Constantine C. Popoff

"INTRODUCTION AND SUMMARYDuring 1946 several high-grade limestone deposits in western Washington were examined by the Bureau of Mines. This report presents the data obtained from investigation of the Sauk Mountain deposits in east-central Skagit County, Washington.The investigation consisted of transit and topcgraphic surveys and sampling. The areas selected for sampling were first cleaned by blasting; channel samples up to 40 pounds were cut where practical. Chip samples averaging 30 pounds were taken where channel samples could not be cut. A total of 21 samples in the Sauk Mountain area were taken and. analysed. The locations of the samples are shown in figures 2 and 4, and the analyses are listed in tables 1 and 2. This investigation is a part of a long-range program of general investigation of mineral resources for future industrial development of the Pacific Northwest. The Sauk Mountain deposits were investigated for the purpose of disclosing now sources of high-purity limestone, which could be mined and shipped at low cost to Seattle and other industrial cities in the Pacific Northwest."

Oct 1, 1948

By R. V. Higgins

A numerical method is presented to calculate the pressure distribution in a petroleum reservoir that has irregular boundaries. The computer program is straightforward and requires minimal data preparation. The method can also be used to determine pressure distribution in many other types of underground reservoirs. In this method, the grid solution of the fluid-flow equations in a reservoir that has regular boundaries (previously published) was expanded to handle irregular boundaries. The computer program locates grid points at the irregular boundaries. The method of mirror images is then used to form a special stencil to determine the pressure at each of these points. Two examples are presented to demonstrate the applicability of the method for virtually any reservoir configuration.

Jan 1, 1972

By B. M. Bird

For several years the U.S. Bureau of Mines and the University of Washington have been cooperating, in a study of coal tabling. The first pert of the work consisted of experiments using, one of the commercial-sized coal washing tables in the laboratories of the College of Mine. As an outgrowth of this work, hindered-settling classification has been successfully applied in the tabling of coal4, and several important improvements, mainly in the riffling, have been made in the table itself. Both of these developments have resulted in increasing the rapacity and efficiency of the coal-washing table. In order to facilitate further progress in this work an investigation has been undertaken to throw more light on the mechanism of table separation. The final separation of a table is obviously the resultant of several operations; namely, stratification, removal of the top strata or parts of them as washed coal by the cross-flowing water, and removal of the bottom strata or parts of

Jan 1, 1929

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-MM-scfd, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 mi 11 ion tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of May 12, 1974, under the terms of the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 and early 1974 indexes . Initial capital investment varies: $45,358,600 for the 4.8-million- ton-per-year (MM tpy) mine in the Eastern province, $54,603,000 for the 6.72 MM tpy mine in the Interior province, and $29,871,000 for the 9.2 MM tpy mine in the Northern Great Plains province. Total capital invest-ments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $61,070,000, $76,753,000, and $56,286,000, respectively. Corresponding selling prices for the coal, per ton, are $4.79, $4.23, and $2.66, assuming a 12-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1974

By G. L. Oldright, Virgil Miller, F. K. Shelton, Keck. W. E., Horst Sieg

Potash is one of the principal foods and is necessary for the growth of most vegetables, grains, and fruits. For many years, this country depended entirely upon foreign sources for its supply of potassium compounds. However, during the last 15 years the domestic production of potash has gradually increased, as shown in table 1. 7/ Imports now supply only half of the American market. In 1936, the equivalent of 207,000 tons of K20 was imported, and 210,000 tons was produced domestically. In 1935, domestic consumption was approximately 420,000 tons of potash, a 57 percent increase over that for 1934 and surpassing previous peaks of 1928 and 1930.

Jun 1, 1937

Lower the respirable dust exposure of longwall shearer operators by isolating and con-fining the dust cloud near the face. Approach Install conveyor belt screens at various locations on the body of the shearer to contain and hold the dust cloud toward the face side of the machine. This approach provides a cleaner air split in the walkway, over the shearer operators. How It Works On most longwall shearer sections, the dust exposure of the shearer operators is primarily attributable to the machine it-self. The dust cloud originates at the face, and the exposure of the operators depends largely on how quickly this dust spreads into the walkway. Conveyor belt screens placed on the gob side of the body of the machine can reduce the amount of dust which spreads out into the walk-way. In addition, belting may be installed over any open spaces between the shearer under-frame and the panline to prevent conveyor dust from boiling out into the operator&apos;s walkway.

Jan 1, 1981

By William J. Campbell

The possibility of chemical analysis by identification of characteristic X-ray spectral lines was first suggested by H. C. J. Moseley in 1913.3/ For a given spectral series it was found that the frequency of the characteristic radiation was proportional to the square of the atomic number of the excited atom. Siegbahn and his coworkers improved the instrumentation and accurately determined the wavelengths of the characteristic spectra for most of the elements .4/ In fluorescent X-ray spectroscopy, the characteristic X-rays of atoms are emitted or fluoresced upon absorption of primary or incident X-rays of shorter wave-lengths (higher energies). The K spectral lines are used for elements of atomic numbers 13 to about 63, and the L series for those above atomic number 50. Whether the K or L lines are used for elements 50-63 depends upon the type of instrumentation available. The laboratory at the Eastern Experiment Station of the Bureau of Mines, College Park, Md., uses the K lines up to atomic number 57 and the L lines for thong elements of higher atomic number.

Jan 1, 1955