Search Documents

By J. F. Messerly

The purity of three specially prepared samples of benzene was determined with an adiabatic, low-temperature calorimeter with automatic control of shield temperature. Extensive measurements were made on each sample to determine how variations in operating procedures affect melting-point and freezing-point as well as purity data obtained by the calorimetric method. Detailed results of the investigations are presented, and effects of different operating procedures are discussed, together with problems encountered in interpretating experimental results.

Jan 1, 1963

In 1962 and 1963, two in situ combustion pilot tests were conducted in the shallow Second Venango sand near Reno, Pa. Because of poor oxygen utilization and lack of production response, both tests were considered failures and were terminated. The area was then relatively inactive until late 1966, when a development well drilled near the 1963 test site had surprisingly good production in what was considered to be a pressure-depleted reservoir. Other wells drilled in and around the old thermal pilot areas also came in as good oil producers. This report presents a study of the increased oil production from the Second Venango sand in the Reno area, and the apparent connection of the present production response and the old thermal pilot tests. Apparently combustion occurred in the Second Venango sand after the 1962 and 1963 experiments were terminated and, supported by large volumes of air left in the reservoir after the 1963 test, generated carbon dioxide which helped repressure the formation. This field evidence of combustion warrants another pilot experiment to further explore the use of properly designed in situ combustion techniques in increasing production from the Second Venango sand.

Jan 1, 1971

By H. O. Poppleton, F. E. Block

This investigation was made to develop a method of preparing high - purity thorium metal in quantities up to 20 kilograms per batch . Several methods for the preparation , purification , and reduction of thorium tetrachloride are discussed . Thorium tetrachloride was prepared by chlorination of decomposed thorium nitrate or oxalate with carbon tetrachloride or phosgene . tion of the crude tetrachloride was achieved by multiple distillations or by filtration of the molten chloride . It was found that high - purity thorium metal could be prepared by sodium reduction of thorium tetrachloride if chloride of sufficient purity were available . Byproduct salts and excess reductant were removed by vacuum distillation , and the resultant thorium metal sponge was consolidated by consumable - electrode or fixed - electrode arc melting . It was demonstrated that metal prepared by this method could be fabricated into bar , rod , or sheet , at room temperature .

Jan 1, 1964

By Paul R. Thimas, Edward H. Boyle

"The Bureau of Mines evaluated the long-term cost and availability of primary gold production from 135 mines and deposits worldwide. Collectively, the evaluated countries represent 93 pct of world gold production. Total recoverable gold available (as of January 1984) from a subset of 111 significant producing mines and developing deposits in 13 market economy countries (MEC's) is estimated at 810 million tr oz. The Republic of South Africa is estimated to account for 87 pct of total recoverable gold. The United States and Canada account for 4 and 4.5 pct of the total, respectively. Eighty-three percent of total recoverable gold is available at a constant 1984 break-even price of $400/tr oz, and 70 pct is available at $300/tr oz. South Africa accounts for 90 pct of the gold available at $400/tr oz or less.Major conclusions are that (1) South Africa should remain the largest world producer through the year 2000, (2) annual MEC output in 2000 should not be significantly different than current output given constant 1984 gold prices of more than $300/tr oz, and (3) there may be a significant decline in production after 2010 in the absence of major new discoveries and continued development of new mines to offset the depletion of the South African mines. INTRODUCTIONSince the late 1970's the world gold mining industry has been characterized by dynamic growth in production and volatility in price. World production in 1983 was almost 15 pct greater than in 1980, and the short-term trend continues upward. Annual dollar-based price changes since the early 1970's have been unprecedented in both magnitude and volatility. This commodity, which sold for $35/tr oz3 for over a third of a century, reached an annual average $612/tr oz in 1980. Until 1980, the future price of gold seemed set on an upward trend. Since that year, however, world gold prices have fallen by over 50 pct to slightly over $300/tr oz at the end of 1984.Against this background, this study was undertaken to determine (1) the level of world demonstrated gold resources, (2) total and annual availability of gold mine production, (3) long-run production costs per operation and by national aggregates, (4) the economic and technical factors that impact upon cost and availability, and (5) probable future mine production and cost trends."

Jan 1, 1985

By R. Havens, B. K. Shilber

"INTRODUCTION In the course of the investigation of the occurrence of manganese deposits in the western United States, ore-dressing tests were made on three samples procured by Bureau of Mines engineers from two properties in southeastern Juah County, Utah, each of which is known by the name Black Jack. To avoid confusion, the tests will be described under the names of the owners Kendall-Duvall and the Empire Mines.None of the samples were amenable to ore dressing for the production of high-grade manganese sinter.Ores from the Kendall-Duvall deposit represent an interesting metallurgical phase of low-grade manganese occurrence, as the occurrence of manganese as silicate (braunite) automatically governs the extent to which they can be beneficiated by mechanical methods of treatment. As less than 50 percent of the total manganese was recoverable by complex methods of treatment in a 40- percent-manganese sinter, attempts were made to recover most of the manganese in a low-calcite, intermediate-grade product that might be acceptable for subsequent metallurgical treatment. By selective flotation of calcite and manganese, up to 68 percent recoveries were obtained in plus 20-percent manganese products..No encouragement can be given for successful ore-dressing of Empire ores as represented by samples received for testing, as no products were obtained that would meet minimum marketing specifications. Empire ore contained only 1 percent lime and might be high enough in grade (19 percent manganese) for direct hydrometallurgical treatment."

Nov 1, 1947

By Michael G. Zabetakis

The autoignition temperatures (A.I.T.'s) of natural and synthetic lubricants in air were generally found to decrease with increasing pressure. Of the two types of fluids, synthetic and natural, studied in some detail, the phosphate esters had higher A.I.T.'s at any pressure between 1 and 200 atmospheres than the mineral oils. Most of the A.I.T. data obtained in this study obeyed the relationship predicted by Semenov's theory of ignition.

Jan 1, 1962

By F. W. Brown, F. C. Gibson

"INTRODUCTION There is urgent need for a satisfactory permissible multiple-shot blasting unit capable of firing 10 detonators in series and safe for use in underground mining where a. gas-ignition hazard may exist.. As there is at present no entirely satisfactory permissible unit of either the battery or generator type, tile described capacitor-battery type has been developed. Consideration of the Bureau of Nines approval schedule pertaining to the generator and magne to-type units and of the electrical characteristics of the unit described in this report indicate that this unit should meet Bureau of Mines permissible requirements.This report gives a detailed description of the design and operation and results of tests to determine safety of operation in gassy atmospheres.DESIGN AND OPERATION OF UNITOperation of the vibrator-type multiple-shot blasting unit is based upon utilization of the discharge energy from a capacitor charged to a given. voltage and having capacitance adequate to store enough energy to initiate 10 detonators in series. The primary source of energy is a 4-volt cap lamp battery such as is carried for illumination on the person of underground workers in nearly all mines. As this battery is already available and is recharged daily it is considered to be a reliable and convenient source of energy for a blasting unit. Figure 1 is a schematic diagram of the circuit for an improved unit, and figures 2 and 3 are views of the experimental unit. The battery potential is applied through a radio-type synchronous vibrator (8) to an 8-volt center-tapped primary of a small transformer (9) having a high-voltage center-tapped secondary. The vibrator introduces an alternating low-voltage potential into the primary and mechanically produces full-wave, rectified, pulsating, direct current from the secondary. A buffing condenser (11) across the secondary gives the proper wave form for long vibrator life: a resistor (12) its in series with this condenser across the total secondary to protect the transformer in case of• failure .of this capacitor. A voltage divider (10) with an adjustable slider permits accurate adjustment of the potential applied to the high-capacity firing condenser (5)."

Oct 1, 1947

By G. S. Scott

The Bureau of Mines is engaged in research to assess the hazards associated with the handling, storage, and use of combustible gases, vapors, and. liquids encountered in mines and in industry. As a part of this general pro-gram, numerous limits of flammability and ignition temperatures are being investigated for a wide variety of combustible materials, and methods are being developed to minimize the explosion hazards of these combustibles. The Bureau receives numerous requests for information on the explosion hazards of specified combustible mixtures under various conditions of use. This information circular has been prepared to assist those who may have similar requests. Destined primarily for the layman with a limited technical knowledge of the subject, it considers rather briefly the numerous factors that enter into the general problem of gaseous explosions and their prevention.

Jan 1, 1951

By Arthur B. Johnson

The Bureau of Mines investigated the concentration characteristics of high-clay sylvinite ores from four potash companies operating in the Permian Basin near Carlsbad, N. Mex. These ores, containing 13 to 22 percent K20 and 3 to 7 percent clay slimes, cannot be effectively processed by current commercial flotation methods because of their high slime content. A solution to this problem was shown to be the use of two-stage moderate scrubbing conditions and washing of the ore as opposed to strenuous attritioning. Bench-scale physical beneficiation techniques for recovering potash minerals and the development of ore-dressing systems by flotation resulted in obtaining acceptable product grades and recoveries. By using a coarse grind, emphasis was placed on production of premium granular and coarse products. Flotation results showed that concentrates of 58.7 to 60.4 percent K20 with recoveries of 71.0 to 83.4 percent 0f the K20 values can be obtained.

Jan 1, 1971

By W. H. Herschel, E. W. Dean

"IntroductoryThe common practice of the petroleum industry is to measure viscosity by the use of instruments of the efflux or capillary tube type. The Saybolt universal viscosimeter has been tentatively adopted as a standard by the American Society for Testing Materials and is used extensively in the United States.Several instruments of foreign origin are also more or less familiar, such as the Redwood, the Engier, and the Baroey.Effina-type viscosimeters are well adapted to the ordinary needs of petroleum testing laberatories as they are simple and rugged in construction and away to manipulate, even in the hands of operators lacking scientific training. They have, however, certain limitations and for certain spacial types of work there are notable advantages incident to the use of the so-called torsion types of type of viacosimeter. The most satisfactory type of torsion viscosimeter now available in the market some to be that of MacMchael, which has been discussed in detail in a recent paper (Herschel, W. H., The MacMichael Torsional Viscosimeter. Jour. of Int. and Eng. Chem., vol. 12, 1920, pp. 282-286). The present paper indicates conditions under which this viscosimeter may be used to advantage in the petroleum laboratory, and outlines simple methods of operation and calibration."

Jan 1, 1921

By M. E. Tyrrell, J. Koster

This work was undertaken to determine the feasibility of making mixed diborides of two metals directly from the metal oxides , boron carbide and carbon . The diborides (Ti , V ) , B₂ , (Ti , Cb) B₂ , and ( Ti , Ta ) B₂ were prepared in a crucible resistance furnace at 2,100 ° C , and X- ray- diffraction analyses showed each was a homogeneous solid solution containing approximately equal molar contents of the given diborides . The diboride powders were cold - pressed ; sintered to 2,300 ° C , and evaluated for mechanical strength , rate of oxidation , and resistance to molten metals . The diboride ( Ti , Ta ) B₂ exhibited the best mechanical properties ; the diboride ( Ti , Cb ) B₂ , the lowest cumulative rate of oxidation . The mixtures were stable in the presence of molten aluminum and copper but were attacked by molten Ti , Zr , and Cr .

Jan 1, 1964

By N. S. Dalal, V. Castranova, X. Shi, W. Wrr, V. Vallyathan

"SUMMARY Data presented here indicate that freshly fractured silica exhibits surface characteristics and biologic reactivity distinct from aged silica, and on this basis we propose that these surface features may lead to enhanced manifestations of lung Injury. Grinding of silica produces ~10"" Si and SI-O (silicon-based) radicals per gram of dust on the particulate surface which are characterized by an electron spin resonance (ESR) spectrum centered around g = 2.0015. These silicon-based radicals react with aqueous media to produce OH radicals, which are demonstrable using a DMPO spin trap. The concentration of silicon-based radicals in silica decreases with aging in air and exhibits a half-life of ~30 h, whereas its ability to generate OH radicals in aqueous solution decreases with a half-life of ~20 h. However, on storage in aqueous media, the concentration of silicon-based radicals end the dust's ability to generate OH radicals decrease significantly within a few minutes. Freshly ground silica is also more biologically reactive than aged silica, because freshly crushed silica activates a greater respiratory burst In alveolar macrophages than aged silica, i.e., storage of ground dust in air decreases silica-Induced superoxide anion secretion, hydrogen peroxide release, and NBT reduction by 25%, 68%, and 43%, respectively. Furthermore, compared to aged silica, freshly ground silica exhibits a greater cytotoxic effect on cellular membrane Integrity, i.e., a 1.5-fold increase in LDH release from macrophages, a 36-fold increase in hemolytic activity, and a three-fold increase in the ability to induce lipid peroxidation. Because acute silicosis is frequently associated with occupations in which freshly fractured crystalline silica of respirable size is generated, the present study suggests that fracture-generated silicon-based radicals may play a significant role in the pathogenesis of this disease. AM REV RESPIR DIS 1955; 133:1213-1218IntroductionOccupational exposure to crystalline silica can be associated with either chronic or acute pulmonary disease. Chronic silicosis becomes manifest 20 to 40 years after first exposure and is characterized by development of concentric hyalinized nodular lesions in the lung with the de-velopment of dyspnea over a period of several decades. Acute silicosis, on the other hand, is manifested by a rapid on-set after exposure and is characterized by the accumulation of an amorphous granular lipoprotein exudate in the airspaces and rapid development of respiratory disability within a few years (1-3).Information is growing concerning the etiology of chronic silicosis. Studies sug-gest that several mechanisms may be in-volved in the development of fibrosis. Lung injury may result from silica-induced release of lysosomal enzymes from alveolar macrophages (4, 5). In ad-dition, silica-induced activation of su-peroxide anion and hydrogen peroxide release from alveolar macrophages may result in oxidant-induced damage to lung parenchyma (6). Silica exposure can also result in the release of mediators from alveolar macrophages which enhance the proliferation of fibroblasts and the syn-thesis of collagen by these pneumocytes (7, 8)."

Jan 1, 1988

By Alexander M. Gow

This paper summarizes a survey of fine-grinding practice in ore-concentrating plants throughout the United States, Alaska, Canada, Mexico, and Cuba as reported in the Bureau of Mines Information Circulars on milling methods. The survey covers 49 concentrators, which have a combined capacity of over 160,000 tons per day. In these plants 470 ball, rod, and pebble mills prepare material for flotation, gravity concentration, amalgamation, cyanidation, and air separation. The ores are those of gold, silver, copper, lead, zinc, molybdenum, feldspar, and pyrite. The metallurgy is that of the period 1928-32. Of these 49 concentrators, 36 are in the United States. They can treat 134,400 tons per day, and they have 326 fine-grinding mills. In the United States there are about 100 active or temporarily idle concentrators, exclusive of the many plants in the Tri-State zinc district, the washeries of the Lake Superior iron ranges and the Florida phosphate area, and small gold and silver concentrators. These 100 plants have an estimated capacity of 290,000 tons per day and employ about 650 ball, rod, and pebble mills. Consequently, since this paper covers about half of the production of this country it may be considered as particularly representative of fine grinding in ore mills in the United States.

Jan 1, 1933

By M. M. Fine

"Button" type ore from the Cason mine, Batesville, Ark., can be up-graded to plus-40-percent manganese by mineral-dressing procedures. A simple process including gravity concentration and. magnetic separation yielded more than 50-percent recovery of concentrates containing 38.1 to 40.6 percent manganese. These values in turn could be raised to 41.4 and 42.8 percent, respectively, upon sintering to conform to size specifications. The Bureau of Mines in the past has surveyed and tested many manganese ores and prospects in an endeavor to alleviate the shortage of manganese. The present period of emergency again emphasizes the strategic position of the metal, and manganese investigative work is being stressed to find new ore bodies and to apply newer beneficiation techniques to the known deposits.

Jan 1, 1953

By Robert F. Chaiken

The U.S. Bureau of Mines conducted an experimental and theoretical study of coupled chemical kinetic and mass transport processes during leaching of pyrite from coal in a counterflow, "trickle-bed" column reactor. Spatial and temporal data on reactant and product concentrations were used as solutions to appropriate continuity equations, which in turn define chemical kinetic reaction rates. Data from four 180-by 30-cm column leaching experiments using coal, coal waste, and air-water and air-FeC13 lixiviants have been analyzed. The rate of leaching was found to be diffusion limited (probably by Fe3+) and not controlled by bacterial action. Rates of pyrite oxidation were found to vary with elapsed time (80 to 225 days) and followed a bell-shaped curve, sometimes with a delay before start of reaction. Maximum rates of reaction ranged from 3 to 10 (mmol/d)/L (column) for coal waste and 0.4 (mmol/d)/L (column) for coal. Reaction was 30 to SO pct complete, probably due to precipitation of product salts (e.g., jarosites), which impede transport of oxidant through the coal. An absorption-desorption model of solids leaching, which considers the role of heterogeneous porosity in solids leaching, was used to describe time-dependent leaching rates.

Jan 1, 2010

By Alexander May

The U.S. Bureau of Mines conducted studies to determine if phosphate slag stockpiles at Tennessee Valley Authority's National Fertilizer Development Center were hazardous materials. The stockpiles were not hazardous materials as determined by Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test. Radium-226 concentration was 28.7 pCi/g in slag and 2.1 pCi/g in background material. Radium-226 was not leached from the slag. Fluoride concentration was 3.87 pct in slag, 0.18 pct in subsurface material under slag, and 0.08 pct in the background. Slag material permeability was 1.65 x 10-3 cm/s, and subsurface material permeability was 3.24 x 10-6 cm/s. Rain water, trapped in a depression on top of the east slag stockpile, became seepage water at the base of the stockpile. Concentrations of EPA toxic elements in seepage water were much less than concentrations from an EPA EP toxicity test on the slag. Twelve elements-Na, Mg, Ca, Sr, Ba, Cr, Mn, Co, Cu, Cd, AI, and P-had higher concentrations in seepage water than in rain water on top of the slag stockpiles, or in creek water adjacent to stockpile bases, indicating that they were leached from slag stockpiles.

Jan 1, 1990

By D. J. Stoops, H. Kato, M. D. Carver

The effects of impurity elements silicon , aluminum, copper , nitrogen , and manganese , at 50 to 300 ppm, on properties of the zirconium alloy Zircaloy 2 were investigated . Variations in microstructure , mechanical properties , and corrosion behavior in some inorganic acid and salt solutions were observed with variations in level of impurity element . Corrodents were solutions of sulfuric acid , phosphoric acid , copper chloride , and iron chloride . Silicon was found to modify annealed microstructures by spheroidizing and dispersion of secondphase material throughout grains . Silicon or manganese improved ultimate and yield strength of the alloy without loss in ductility . All five elements affected corrosion rates of the alloy , the effect being generally different for each element .

Jan 1, 1964

By Frank G. Horino

A rock mechanics program (composed of laboratory and field tests) was initiated by the Bureau of Mines in an effort to determine the causes of pillar instability at the Fletcher mine, near Bunker, Mo. Compressive strength, Young's modulus, shear strength, and the angle and coefficient of internal friction were determined on drill cores obtained from 16 different locations in the mine. Results of the laboratory tests showed that highly mineralized zones and brecciated zones in pillars could significantly affect pillar strengths and stability in locations where extraction ratios exceeded the normal design ratio of approximately 78%. High-angle fractures that were present in Some locations also may have contributed to pillar deterioration. In the field tests, in situ stress determinations were made in one pillar to establish the pillar-loading conditions and to evaluate the stability of the pillar. Continued monitoring of stresses in the pillar showed a gradual decrease in compressive stress, indicating that the pillar was probably in the postfailure state. A second stress determination was made in a vertical hole in the underlying igneous rock that was exposed on one section of the mine. Horizontal stresses were compressive and larger than would be expected from gravity loading.

Jan 1, 1978

By John Nagy

The effect of low percentages of methane (0 to 5 pet.) in an air atmosphere on spark initiated explosions of coal dust was investigated. With low dust concentrations (0.1 to 0.4 oz./cu, ft.), small amounts of methane increase the explosion pressure; with larger dust concentrations (0.5 to 2.0 oz./cu. ft.), small amounts of methane decrease the explosion pressure. The rate of pressure rise of a coal dust explosion increases with increase in methane concentration; about 3 to 4 pct. further addition of methane yields a decrease in the rate of pressure rise. Convection currents created by the air or gas blast used to disperse dust produce an increase in explosion pressure and rate of pressure rise. The minimum explosive concentration of the coal dust decreases about linearly as the concentration of methane increases from 0 to 5 pct. The explosion pressure increases linearly as the initial pressure within the chamber increases. Similarities between coal dust and methane explosions are indicated, INTRODUCTION During coal mining, methane occluded in coal or adjoining strata is liberated into the mine atmosphere,4 Normally, the methane is diluted and swept away by the ventilating air. Under some conditions, through accidental disruption of the ventilation system, sudden outburst, or because insufficient fresh air is supplied to a working place, low percentages of methane may be present during mining operations. If it is permitted to accumulate, methane itself presents an explosion hazard; its limits of explosibility arc approximately 5 and 15 pct. The effect of low percentages of methane on the explosibility of coal dust was studied to provide a broader understanding of the hazards of ignition and explosion and thus to facilitate development of control

Jan 1, 1961

By Holmes, George H. Jr.

The Cherry Creek tungsten district was explored by the Bureau of Mines from April 16 to August 13, 1942. This district is in north-central White Pine County, Nev., 50 miles north of Ely. Principal work was done on the property of the Cherry Creek Tungsten Mining Co. and at the adjacent Chance mine, although the entire district was examined and mapped. The exploratory work was done in cooperation with the Federal Geological Survey and comprised surveying, trenching, sampling, long-hole and core drilling, rehabilitation of mine workings, road building, drifting, and shaft sinking. The more important tungsten occurrences were explored by trenching and diamond drilling. Sixteen holes, having a total length of 2,515 feet, were drilled. The project resulted in partial development of three new tungsten deposits and small increases in the reserve tonnage of two scheelite-bearing lenses that were being mined by the company. The following pages summarize the history of the district, outline the ownership of the properties explored, and describe the physical features and mineral deposits. Mining and milling practices at the Cherry Creek tungsten mine are outlined, and the plan and results of project work are presented in detail together with surface maps, assay maps, and drill-hole logs.

Jan 1, 1950