Search Documents

By J. Croeni

The search for new alloys for application in the atomic energy field had prompted investigation of zirconium-rare earth metal alloys by the Federal Bureau of Mines. In this instance the zirconium-dysprosium system was investigated by melting point, thermal analysis, resistivity, X-ray and metallographic methods. Results indicate a single eutectic system with a peritectoid reaction occurring at 890° C. The eutectic isotherm extends from 30 to 95-percent dysprosium at 1,280° C. Eutectic composition is located at approximately 70 percent dysprosium. Solid solubility of dysprosium in both alpha and beta zirconium is extensive. The extent of solid solubility of zirconium in dysprosium has not been determined. Although zirconium rich alloys exhibit a significant increase in hardness, they can be cold worked extensively. These alloys also appear adaptable to solution heat treatment. Additional investigations concerning corrosion resistance and other mechanical properties are necessary for satisfactory evaluation of these alloys. The superior corrosion resistance of zirconium and the nuclear cross-section characteristics of the rare earth metals have stimulated alloy investigations using zirconium as a base metal. Alloys combining these characteristics present a possible substitute for hafnium as a control rod material. In this particular study dysprosium was chosen as the alloying element, and several series of alloys were used to establish the equilibrium diagram.

Jan 1, 1960

By Foster Fraas

In the separation of a component from a mixture , two fractions are obtained , one containing a high - percentage composition of the component and the other a low - percentage composition . The high - percentage fraction is frequently called the concentrate and the low - percentage fraction the tailing . In many separation processes the recovery is not complete , and the composition of the concentrate decreases as the recovery of the component, which is concentrated , increases . It is this particular class of separations to which this paper is confined .

Oct 1, 1942

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, conducted a study of past mine explosions to identify the ignition locations and ignition sources responsible for the most severe explosion events resulting in death. Since the Scotia disaster of 1976, many fatalities from underground coal mine explosions have been linked to nonpermissible electrical equipment ignition sources located in intake air courses. With few exceptions, explosion protected equipment is generally not required in intake air courses of gassy underground coal mines in the US. Cigarette lighters were another prevalent ignition source for fatal explosions ignited in intake air courses. Several mine rescue/ recovery teams have encountered electrical ignition hazards. The study provides evidence that intake air courses of gassy underground coal mines fit the description of certain Hazardous (classified) locations described in the US National Electrical Code®. Class I Division 2 or Zone 2 explosion protection tech¬niques may be used to design intake air equipment so that it does not present an ignition source under normal operation, before mine power is shut down in emergency situations. Nonpermissible circuits in intake air courses that are likely to remain energized during emergencies, e.g. battery powered equipment, should be protected by more stringent Class I Division 1, Zone 1, or Zone 0 techniques, to protect rescue/recovery personnel.

Jan 1, 2009

By David W. Houseknecht

Probabilities of encountering coalbed discontinuities during vertical or horizontal drilling in a specific coalbed can be estimated based on analysis of mined-out areas of the coalbed where the size, shape, orientation, and distribution of discontinuities are known. The result- ant probability estimates can be applied to cost-risk evaluations of drilling programs proposed for exploratory, developmental, or methane drainage purposes in undeveloped areas of that coalbed. Data compiled from mine maps of the Beckley Coalbed in southern West Virginia were used to estimate the probabilities that discontinuities would be encountered in two illustrative hypothetical drilling programs--one for drilling vertical boreholes and the other for drilling horizontal boreholes. Analysis based on a mined-out area of the Beckley Coalbed indicated that vertical methane drainage boreholes spaced 1,000 feet apart in a square grid pattern would each have a 29 percent probability of encountering a discontinuity in a geologically unexplored area of the coalbed. It was also determined that exploratory vertical drilling could locate most of the discontinuities if a borehole spacing of 2,500 feet were used. For horizontal drainage boreholes in the Beck- ley Coalbed, the analysis indicated a linear relationship between hole length and the probability of encountering a discontinuity.

Jan 1, 1982

By Irving Hartmann, Bernard Lewis, John Nagy, H. P. Greenwald, H. C. Howarth

"ORIGIN OF INVESTIGATIONThe Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States, July 24J 1946, contains the following provisions with regard to rock dusting: Article VI. - Section 2. Rock dusting.(a) All mines, except those mines or those locations in a mine which are too wet or too high in incombustible content to propagate an explosion, shall be rock-dusted to within 80 feet of the faces of rooms and entries; however, if the mine or any part of it is wet but becomes dry, the mine or portion of the mine so affected shall be rock-dusted as ·soon as it becomes dry. (b) In mines partially rock-dusted or in mines that are required to start rock dusting, haulageways and parallel entries connected thereto by open crosscuts shall be rock-dusted. Back entries shall be rock-dusted for at least 1,000 feet outby the junction with the first active entry. Inby this junction, the rooms, entries, and crosscuts shall be rock-dusted by generalized rock dusting as provided for in section 2(a).(c) Where rock dust is applied, it shall be distributed upon the top, floor, and sides of all open places and maintained in such quantity that the incombustible content of the mine dust will not be less than 65 percent. In trackless entries and air courses, protection in lieu of generalized rock dusting may be had by using bags filled with rock dust, if they are placed at regular intervals and staggered as described in Bureau of Mines Report of Investigations 3411."

Feb 1, 1948

By Spencer P. Howell, Munroem Charles E.

"Introduction;As in the case of TNT previously presented*, this report presents the results of an investigation to discover the safest and best way of utilizing picric acid for industrial blasting purposes. It describes the physical and chemical properties of this explosive, gives precautions to be observed in handling, packing, preparation of cartridges, and holes, presents the results of field tests in blasting stumps and bowlders, and compares the results with those obtained from dynamite.The investigations reported herein were undertaken and this paper has been prepared, solely to aid in the salvage of the surplus picric acid accumulated for war uses and released by the declaration of the armistice. No funds were available nor have any been appropriated with which to defray the expense of converting this picric acid into any other form or to prepare any explosive mixture from it. The sole problem was to find appropriate uses for this military picric acid in existing needs and to show that it can be efficiently used in carrying out essential civil projects.It is not intended by this publication to promote the use of picric acid as an industrial explosive further than is necessary for the proper utilization of this surplus. On the contrary, the authors believe that picric acid by itself is unlikely to come into general use as an industrial explosive, chiefly because of its cost but also as shown by the clouds of smoke it emits on explosion and the nature of the reactions it undergoes because we do not obtain from it its highest efficiency. As demonstrated in its previous use in Joveite, better results and higher efficiencies may be obtained by mixing picric acid in proper proportions with sodium nitrate or ammonium nitrate, to more completely oxidize the picric acid, and another nitrosubstitution compound, such as nitronaphthalenes, with which do desensitize and waterproof the composition formed. By such admixture not only may the energy resident in the picric acid, be more fully utilized but the cost of the resulting blasting explosive should be much less than that of picric acid."

Apr 1, 1921

By H. E. Powell

The smelting of brass and bronze generates a dust composed primarily of zinc oxide, with lesser amounts of other metal oxides, such as copper, lead, and tin. The small quantity of this waste generated by individual smelters and the relatively low unit value of the contained metals, suggests the desirability of reclaiming the metals onsite or at some nearby point. The Bureau of Mines has developed a process that fits these requirements. The technique consists of (1) dissolving zinc and copper from the dust with sulfuric acid, (2) recovery of copper by cementation, (3) recovery of zinc as zinc sulfate crystals, and (4) recovery of lead and tin as a salable residue. Alternatively, zinc may be recovered by electrodeposition. Free acid is recycled and no major pollution problems are generated by the process.

Jan 1, 1972

By M. Kanda, J. W. Adams

A system for measuring amplitude probability distributions (APD’s) of electromagnetic noise in coal mines is described and typical APD’s from an underground coal mine are presented. The APD is a basic statistic required for the design and analysis of communication systems, especially those intended for use in noisy environments, and where neither overdesign nor underdesign is acceptable. The rms and average field strengths are obtained by integration of the APD, and examples are shown at several frequencies. All field strength levels are given in absolute units. Selected frequencies cover the range from 10 kHz to 32 MHz.

Jan 1, 1973

By Albert E. Long

To date the commercial diamond bit setters have been principally interested in the speed with which they could produce a sharp, fast-cutting bit. Thus, a premium has been placed on setters who combine a high degree of manual dexterity with the ability quickly to select the Sharp points and edges of the diamonds and set them in the mold without lost motion. The premium on speed does not allow the setters the time, nor are they trained, to consider also the crystallographic structures of the diamonds which are the clues indicating the harder and more suitable working surfaces. Since early fall of 1949, the Bureau of Mines has been conducting a long-range series of experiments in which drill bort have been oriented in diamond bits in an effort to determine the effects and economic practicability of utilizing the hardest surfaces of the diamond crystal structure. The preliminary experiments completed to date indicate that a substantial saving in diamonds may be affected by using the harder areas of the diamonds as working surfaces in the crown of diamond bits. The experimental work is being conducted by the Bureau of Mines in the laboratories and full-scale mine of the Mining Research Branch, Minerals Technology Division, Region VIII, of the U. S. Bureau of Mines at the Mount Weather Station, Bluemont, Va.

Jan 1, 1951

By S. H. Ash

The United States Bureau of Mines has published relatively little on the flooding and unwatering of coal and metal mines. Bulletin 229, Fifty-Nine Coal-Mine Fires, published in 1927, contains several instances of the flooding of mines or sections thereof to extinguish fires but does not describe their unwatering. Report of Investigations 2649, Explosion Hazards Incidental to Unwatering Coal Mines, published in 1924, warned against the possibility of gas accumulations in flooded mines and indicated the precautions to be taken. Report of Investigations 2255, An Unusual Hazard in Reopening Long-Flooded Timbered Metal Mines, published in 1921, told of methane being pocketed and the danger thereof. The flooding of mines originates in many ways. At some mines flooding followed reopening after what was thought to be permanent abandonment; also, explosions have caused some mines to be flooded. Extinguishing fires, accidental encountering of underground streams or flooded old workings, and caves of strata admitting water from underground workings, water-bearing strata, or surface accumulations have also flooded all or parts of mines. Unfortunately, un watering often necessitates much study and causes apprehension largely because experiences in similar situations are not generally known, as few descriptions of successful or unsuccessful methods are available. The job has sometimes been contracted for outside the local management involved and has become a matter of record for the contractor only. As the cost-plus contract system often employed in the past is now known to be expensive, careful managements elect to handle the problem themselves, in line with the general policy of cutting expense where possible. This report describes specific in-stances of successful unwatering by operators.

Jan 1, 1933

By W. L. Falke

Procedures in which manganese compounds are reduced and the metal is volatilized and selectively condensed, a hitherto neglected area, were investigated. More than 95 percent of the manganese was recovered from high-melting-point ores whether vacuum volatilization or atmospheric pressure volatilization was used, but neither process is economically attractive under present price-cost conditions.

Jan 1, 1966

By Leslie H. Sharp, Martin J. Gavin

Those of the oil-shale operators in this country who are sincerely attempting to make a real industry out of oil-shale developments, are anxious to obtain fundamental data on the retorting of oil-shale; particularly as regards the effect of certain variable factors in the process of retorting on the quantity and quality of products yielded from oil shales when they are subjected to destructive distillation. From careful examination of a con siderable number of suggested processes for treating oil shales and the con flicting ideas on which they are designed, it seems probable that accurate information of a fundamental nature is highly essential to the successful establishment of an oil-shale industry in this country. . Accordingly, the United States Bureau of Mines, in cooperation with the State of Colorado, is undertaking to furnish some definite and impartial information of this type through investigations now under way at the University of Colorado, Boulder, Colo. A retort for the distillation of oil from oil shale has been designed and installed, together with the necessary auxiliary equipment for controlling and determining variable factors of distillation, and for recovering and de termining the quantity and quality of the products yielded from the shales. The retort is of such a nature that conditions of retorting can be accurately . and completely controlled, and varied at will. It is not designed as a com mercial retort, but only for research purposes. A testing laboratory with equipment necessary for the examination of the shales, physically and chemic ally, and the products yielded by them, has also been fitted up . The material used in the investigations is oil shale obtained from the DeBeque, Colorado, shale field. It yields on distillation in the Bureau of Mines testing apparatus, about 42 gallons of oil to the ton, and is there fore a fairly representative sample of the shales that probably will be first worked in Colorado. The shale used will be as uniform as possible in character and oil yield and will all be obtained from the same seam at the same point, in order to avoid the introduction of unnecessary variable factors in the tests and to render results strictly comparable •

Jul 1, 1920

By Frank L. Hess

In 1876 cassiterite was identified in the placer gold from the northern Black Hills, and such a mixture could have come only from Nigger Hill or one of the streams draining the hill, because in no other hart of the northern hills have cassiterite anti gold been found together. Nigger Hill is in western Lawrence County, South Dakota, and on it is the little camp of Tinton. The Wyoming line runs along the west side of the hill and crosses the ridge which is the hill's continuation about miles north-northwest of Tinton.

Jan 1, 1938

By Frank L. Hess

In 1876 cassiterite was identified in the placer gold from the northern Black Hills, and such a mixture could have come only from Nigger Hill or one of the streams draining the hill, because in no other part of the northern hills have cassiterite and gold been found together. Nigger Hill is in western Lawrence County, South Dakota, and on it is the little camp of Tinton. The Wyoming line runs along the west side of the hill and crosses the ridge which is the hill's continuation about miles north-northwest of Tinton.

Jan 1, 1938

By Oliver Bowles

"Rhodesian asbestos is of high quality and is much in demand by American consumers. Production in Rhodesia was first reported in 1909. The production for this and each succeeding year is shown in the following table:The serious curtailment in production for the years 1912 and 1913 was occasioned by transportation difficulties. In 1914 a railway was projected to Victoria and thereafter production increased greatly. Up to 1916 asbestos was obtained,from the Victoria district only, but thereafter the Bulwayo district became an important,producer with minor quantities from Gwelo.In the Bulawayo district the productive area is about 2 1/2 miles long, with Shebanie mine at the north-west end, the Nil Desperandum at the south end, and the Birthday claims between them."

Oct 1, 1920

By Louis C. Brichta

The Rush Creek district of Marion County, Ark., has had a more or less continuous record of zinc production over the past 40 years. The ore has come from many small mines working on oxidized and semi-oxidized deposits found in the Everton formation where that formation forms the present surface rock. Prospecting has been restricted to the hillsides above the creek levels, the actual ore outcrops being the guides. Little attention has been paid the possible sulfide zones. In August 1942, the United States Geological Survey and the Bureau of Mines recommended exploration of the Powell and Cotter formations, which underlie the Everton, for which purpose the Survey had previously located 18 proposed drill-hole sites in geological structures that seemed favorable to are deposition.

Jan 1, 1949

By John R. Bartels

In laboratory testing, the Bureau of Mines established criteria by which common resin-grouted roof bolting systems can be evaluated and compared. Ultimate strength and stiffness were determined for nonten-sioned full-column, point-anchor, tensioned full-column, and debondable resin-grouted bolts, and for variations on full-column boltsn Bolt per-formances were compared using the performance of the 3/4-in full-column resin-grouted bolt as the standard. New and innovative systems can also be qualitatively compared against this standard. Since the medium into which a resin-grouted bolt is installed is one of the most important parameters affecting bolt performance, various host mediums were used in the testing: sandstone, concrete, simulated coal, simulated shale, and plaster. Bolt performances expected in other mediums can be inferred from the response patterns obtained in these mediums. Results indicate several functional differences among bolt types. Where resistance to shear is important, point-anchor bolts may outperform nontensioned full-column bolts at a lower cost. In medium-to soft-strength rock, tensioned full-column bolts perform best. Also, varying the resin-steel ratio seems to have little effect on the properties of a full-column bolt, when proper resin mixing is ensured.

Jan 1, 1985

By James C. Cawley

The Bureau of Mines has empirically determined ignition probability versus current for resistive circuits in an 8.3% methane-air atmosphere. Simple ignition probability, defined as the number of ignitions divided by the total number of sparks, was determined, and the corresponding currents were recorded. The experiment was designed to minimize the probability of not observing an ignition that should occur during a series of tests. For resistive circuits in 8.3% methane-air mixtures, the experimental results indicate that ignition was not achieved below 2,000 rnA at 20 V dc, 350 rnA at 30 V dc, 150 rnA at 40 V dc, and 175 rnA at 50 V dc. The simple probability of ignition corresponding to these currents is esti-mated to be, respectively, 1.0 x 10-6, 1.7 x 10-7, 3.0 x 10-7, and 1.0 x 10-5 The ignition mechanism seems to break down below this point, implying that a threshold current value exists below which spark ignition does not occur.

Jan 1, 1987

By John J. Sammarco

This U.S. Bureau of Mines report describes the research effort and results for a computer-assisted appendage control system of a Joy 14CM continuous mining machine. The cutter head (shear), gathering head, conveyor, and stabilizer jack are the appendages. Positional control of each appendage is accomplished by specifying the desired position to the appendage control computer, which uses appendage position sensor data. Appendage movement is actuated until the desired position is attained as determined by control algorithms. A description of the sensors, mechanical and electrical interfaces, data acquisition and control (DAC) system, experimental method to determine appendage response characteristics (range of motion, start and stop delay times, and movement rates), and their application to the position control loop algorithms are presented. Also, the test results for the shear in an unloaded (free space) and loaded (cutting) condition of the shear are presented.

Jan 1, 1991

By D. W. Butner

This report is concerned with the conditions affecting the methods and costs of mining phosphate rock in that part of the western phosphate field that is in Bear Lake and Caribou Counties in southeastern Idaho ( see fig . 1) . The area was selected because it contains most of the known phosphate reserve and because its geology has been studied more extensively than that of other sections . Deposits of phosphate rock on public land may be leased from the Government under the terms of the Mineral Leasing Act of 1920 , subject to the regulations of the Bureau of Land Management . Public interest in phosphate production is growing , as shown by an increasing number of applications for leases . Two mines are being operated steadily for the production of phosphate rock by companies that have also the necessary processing plants for the manufacture of fertilizer . Total western phosphate - rock production in 1947 is reported by the Economics Statistics and Division of the Federal Bureau of Mines to have been 1,193,000 long tons , mined in Idaho , Montana , and Wyoming . The average grade was 30.7 percent of contained phosphorus pentoxide (P205 ) ; the average value at the mines was $5.67 per long ton . Idaho contributed 905,000 tons , or somewhat more than 75 percent of western production . Western fertilizer plants took 23 percent of total production; 76 percent was exported . Strip mining accounted for 75 percent of the Idaho tonnage; the remainder was stoped from underground workings . Rock must contain a minimum of 30 percent P205 to be commercially useful for the production of superphosphate fertilizer by current acid treatment methods . Research by corporations and Government agencies has been directed toward the use of lower - grade ore . So far , only by smelting can rock containing as little as 25 percent P205 be used economically . Any development of processing or use pattern that would render the mining of , say , 20 percent rock profitable would have important effects in reducing the unit cost of mining . In the search for metallurgical improvements , consideration should be given to the saving of valuable components of the rock, such as vanadium and fluorine , both of which are present in the beds .

Oct 1, 1949