Search Documents

By T. Aoki, Y. Maeno, R. Kawano, F. Nakahara, Y. Obara, K. Shibata

The mechanical behaviors of fully-grouted long-embedded cablebolts actually used in situ are very non-linear in pull tests and are different from those of short-embedded cablebolts. We have conducted the pull tests of long-embedded cablebolts installed in mockup rock test blocks, which are 4m in the longitudinal length. In order to investigate the mechanical behaviors inside the test block, the axial load distribution along the cablebolt and locations of acoustic emission events were measured during each pull test. It was found that the axial force distributions were quite linear and that the gradients were interpreted as the grout bond strength by taking into consideration the stress balance at the infinitesimal segment of a cablebolt. Les boulons-câbles longs entièrement cimentés qui sont réellement utilisés sur place présentent, au cours des essais de traction, des comportements mécaniques considérablement non linéaires et différents de ceux des boulons-câbles courts. Nous avons mené des essais de traction des boulons-câbles longs installés dans une maquette de fond rocheux servant d’éprouvette d’une longueur longitudinale de 4 m. Afin d’étudier les comportements mécaniques intérieurs de l’éprouvette, la répartition de la force axiale du boulon-câble et l’émission acoustique ont été mesurées durant chaque essai de traction. Il s’est avéré que les répartitions de la force axiale sont sensiblement linéaires et que leurs gradients représentent la résistance d’adhésion en prenant en compte l’équilibre de contraintes à la partie infinitésimale d’un boulon-câble. Das mechanische Verhalten von ganz eingegossenen, lang eingebetteten Kabelbolzen, die vor Ort eingesetzt werden, ist bei Zugprüfungen sehr nichtlinear und anders als das von kurz eingebetteten Kabelbolzen. Es wurden Zugprüfungen mit lang eingebetteten Kabelbolzen durchgeführt, die in Prüfblöcken (Gesteinsattrappen) mit 4 m Länge eingelassen waren. Zur Untersuchung des mechanischen Verhaltens in den Prüfblöcken wurden die Axiallastverteilung entlang des Kabelbolzens sowie das Auftreten von Schallemission im Verlauf jeder Zugprüfung gemessen. Es ergab sich, dass die axiale Kraftverteilung recht linear ist, und die Gradienten wurden unter Berücksichtigung des Kräftegleichgewichts am infinitesimal kleinen Punkt eines Kabelbolzens als Haftfestigkeit interpretiert.

Jan 1, 2003

By B. Larsen

The Søderberg electrode was invented about 95 years ago by the company Elektrokjemisk, later known as ELKEM. It is still the most commonly used electrode system in submerged-arc furnaces for ferroalloys, platinum smelting, and slag cleaning operations. The size of the furnaces and electrodes has increased over the years and electrode diameters up to 2000 mm are today in use. Such large electrodes can be challenging to manage, and large electrodes are also more demanding when it comes to the electrode paste used in the electrodes. Although electrode sizes and equipment around the electrodes have changed, the main principles of the Søderberg electrode processes are the same. To assists in proper understanding of the electrode processes and to optimize electrode management, Elkem has developed several mathematical tools covering various aspect of the process. Both temperatures and thermal stresses can be calculated during dynamic conditions. The paper demonstrates, with examples, how the tools are used in both education and as practical input to improved electrode performance.

Jan 1, 2012

By G. Popplewel

Commencing with the Pre-Feasibility Study (PFS) conclusions, the Orapa 3 process design evolved through a phase of value-engineering studies. An overall re-evaluation of the originally proposed process design was necessary both in order to address the interim increase in target throughput from 9.8 Mtpa to 12 Mtpa as well as to increase capital efficiency. In the interests of clarity, the PFS process design for Orapa 3 has been omitted from this paper, as it is no longer relevant. Recognition is however due to those engaged in earlier phases of the Orapa 3 project with respect to fundamental mass-balancing modelling; and ore and diamond characterization, which fanned the basis for the process design that has evolved from feasibility study activities.

Jan 1, 2010

By Ri McCrindle

"Analytical Chemistry is moving rapidly towards a concept where technicians have to do no more than press a button and print the result from an instrument that is a featureless ""black box"". In this environment we must ask how much traditional ''wet chemistry"" is still required for undergraduate students.Methods that can be fully automated will become increasingly important. An example of such a method is that of the slurry nebulisation and ICP-OES analysis of precious metal concentrate. Grinding the sample and adding Triton X100 as dispersant, complete analysis time is in the order of 90 min as apposed to the traditional Carius tube method which could take as long as 24 h. For most of the elements studied, the results using ""in-house"" reference material for calibration and as samples as well were within the 95% confidence level. Elements of low concentration in the sample (As, Bi and Se) were not within that level."

Jan 1, 2014

By A. K. Raji, E. F. Orumwense, M. O. Ojumu

This research paper introduces a novel passive method for ocean mining using an electricpowered robotic subsea dredging crawler designed to operate in various subsea conditions, including unstructured and rough terrain. The electric-powered robotic subsea dredging crawler is equipped with two driving tracks and features a complex assembly of tank tread chain link, tank tread idler wheels, tank tread sprockets, bronze bushings, motor hub, motor mount, and a 12-volt direct current motor. To evaluate the performance of the electric-powered robotic subsea dredging crawler, it was compared with existing ocean hydraulic exploration crawlers, such as MK3 ROST, in terms of drive performance on an inclined ramp with five angles of inclination (0°, 15°, 20°, 25°, 30°). The experiment aimed to determine the maximum velocity, torque, and efficiency of the crawler at different angles of inclination. The collected data were analysed and plotted using Python, and the effect of the electric-powered robotic subsea dredging crawler’s weight on its driving performance was also considered. The results of this study demonstrate a quadratic relationship between driving performance and inclination angle, which can be used to optimise the electric-powered robotic subsea dredging crawler’s performance for future ocean mining robot drive applications.

Oct 2, 2025

By J. A. Sweet, T. BACHMANN, G. E. Sandoval, T. M. Hauyon, F. A. Contreras

In many respects a porphyry copper ore concentrator plant can be considered as a simple system. Chalcopyrite typically liberates well at relatively coarse sizes, and even low grade ores are amenable to upgrading 20 to 30 times to produce concentrate grades in excess of 25 % in very simple Rougher- Regrind-Cleaner+Scavenger flotation circuits. The flotation response of chalcopyrite has been well characterised in many fundamental and applied research studies and the conditions necessary to depress pyrite and other floating gangue species are well understood. But what happens to the particle surfaces when you have a 50 km pipeline between the grinding circuit and the flotation plant? How does the seasonal variation in water quality affect your ability to control pulp chemistry? What impact does the relative concentration of the different sulphide species have on their separability? Why do two plants that receive nominally the same ore produce consistently different results? And most importantly, what do you need to do to improve the performance of both plants? To answer these and other questions, a focussed sampling and analysis programme was carried out at the Las Tórtolas flotation plants in 2018 and 2019. The work included full down-the-bank sampling, hot floats, the use of radioactive tracers for determining residence time distribution profiles, gas dispersion measurements, detailed mineralogy by size across the circuits and multiple regrind surveys. This comprehensive study was augmented by analysis of historical mineralogy, geometallurgy and operating data using modern data science techniques, and has provided the foundation for current and future optimisation initiatives. Some of the findings and their implementation will be presented in this paper. Keywords: Circuit optimization, Residence time, Gas dispersion, Pulp chemistry

Jan 1, 2020

By I. Silin, H. Wotruba, A. Liono, I. Volobayev, Y. Rubinstein, D. Gürsel

Old, abandoned or in situ processed and storaged tailings can be a potential source of remained valuable metals and minerals. By reprocessing of tailings, it is possible not only to achieve economical profit from recovery of valuable metals, but also to reduce environmental damage caused by tailings such as generation of acid mine drainage from sulfide minerals, mobilization of heavy metals, soils and groundwater contamination. In addition, storage facilities can be successfully redesigned with modern geotechnical requirements and monitoring to avoid a dam collapse of abandoned tailings. In this case study, the processing of low grade abandoned tailings was investigated. Copper (0.15%), cobalt (0.032%) and gold (0.35 ppm) were determined as main valuable and recoverable metals. Cobalt occurs as cobaltite and cobaltiferrous pyrite, while chalcopyrite represents copper. The fine fraction of tailings below 32 μm is enriched with cobalt and copper. Preliminary test-works with initial tailings sample were aimed to recover copper, cobalt and gold. The previously tested magnetic and gravity separation could not recover the metals in a pre-concentration step. Flotation tests of the tailings sample had shown a suitability for flotation without previous regrinding of the tailings. The valuable minerals are first proposed to be recovered by collective flotation, followed by a selective circuit with production of a low grade copper concentrate and a cobalt bearing pyrite concentrate. Based on various tested collectors, amounts of sulfidisation agents and activators, a suitable reagents regime was determined and used for up-scaling by locked cycled test. Keywords: reprocessing, tailings, copper, cobalt, gold, flotation, cobaltite, cobaltiferrous pyrite

Jan 1, 2020

By T. Mahlangu Mahlangu, T. Fungene, K. C. Sole

"Although oxygen is widely employed as the oxidant of choice in gold leaching by cyanide, its low aqueous solubility presents some drawbacks in practical application; hydrogen peroxide has therefore been considered as a possible alternative. The aim of this investigation was to study the catalytic decomposition of hydrogen peroxide, which generates an oxidizing intermediate species, and to understand its effect on cyanide destruction. Operating conditions that facilitated the effective decomposition of hydrogen peroxide were established by varying the pH and catalyst type and concentration. The oxidizing intermediate, detected using an indirect technique, was found to be the hydroxyl radical (OH?). OH? is commonly generated in acidic solutions, but this work demonstrated that it is also produced at the alkaline pH values necessary for cyanide gold leaching. The effects of free and complexed iron and copper catalysts on the oxidation and consumption of hydrogen peroxide and cyanide were also investigated. It was shown that the cyano complexes of Fe(II) and Cu(I) are also effective as decomposition catalysts. Hydrogen peroxide concentrations above 0.01 M decreased the free cyanide concentration, which was attributed to the probable formation of the cyanate anion (CNO-). Although cyanide consumption increased due to its oxidation in the presence of OH?, excessive cyanide consumption in the presence of copper was attributed primarily to its complexation by the unstable copper(I) cyanide species. Rate constants for the decompositions of H2O2 and cyanide by ferrocyanide and copper cyanide were calculated; the latter was identified as being a better catalyst. IntroductionLeaching of gold from its ores using cyanide has been employed for well over a century (Habashi, 2016). Addition of cyanide converts the gold into a cyanide complex (Au(CN)2 -) that is soluble in water (Wang and Forssberg, 1990). The leaching reaction can be represented as Equation [1]:"

Dec 1, 2018

By K. Shin

Determining the anisotropy of rocks has in the past been difficult and rarely attempted in engineering practice. Here we have developed a new practical methodology for measuring orthotropic anisotropy that requires only one hollow cylinder specimen to determine the anisotropy of a set, even when the directions of the anisotropic axes are unknown. Autrefois, la détermination de l’anisotropie des roches était difficile et elle a été rarement essayée dans la pratique de l’ingénierie. Voilà c’est nous qui avons mis au point une nouvelle méthodologie pratique pour mesurer le coefficient de conductibilité thermique de l’anisotropie qui exige un seul spécimen du cylindre creux afin de déterminer l’anisotropie d’une série, même si les directions des axes anisotropiques sont inconnues. Früher war die Bestimmung der Anisotropie von Gesteinen ein schwieriges Verfahren, das in der technologischen Praxis nur selten in Angriff genommen wurde. Wir haben hier eine neue praktische Methodik zur Messung der orthotropen Anisotropie entwickelt, bei der nur ein Hohlzylinder an Gesteinsproben benötigt wird, um die Anisotropie einer Reihe von Steinen zu bestimmen, selbst wenn die Richtungen der Anisotropieachsen unbekannt sind.

Jan 1, 2003

By M. Steyn

This article captures the intrinsic differences of thermal coal products, their utilization and their substitution characteristics. South Africa produces approximately 245 million tonnes of coal annually. Eskom consumes 46% (approximately 112 million tonnes), 26% (approximately 65 million tonnes) is exported, and SASOL Synthetic Fuels consumes 18% (approximately 44 million tonnes) and a further 9% (approximately 22 million tonnes) is consumed by domestic users in various different industries. Marketing theory contributes significantly to understanding the importance of technical product and quality appreciation and comprehension, encompassing elements of price, distribution, and promotion. Coal product specification is determined by the inherent geology of a resource and the number of complex actions to market the product to a specific consuming market. Sampling, analyses, beneficiation application, and an array of parameters contribute to matching thermal coal products to the value-in-use it provides to the different markets and its consuming industries. Coal producer shave come under increased scrutiny since South Africa has been experiencing electricity shortages since early 2008. General misunderstandings were declared on public forums and in the media by both legislators and the South African public since a perception developed that South African coal producers are exporting coal that could be utilized by Eskom.

Jan 1, 2010

By J. G. M. Mukoya, B. Adebayo

"This work was carried out to determine the influence of rock properties and drilling machine parameters on the penetration rate at the SJ pit of Rössing Uranium Mine, Namibia. Rock properties (uniaxial compressive strength, tensile strength, and modulus of elasticity) of samples collected were determined in the laboratory. Drilling experiments were conducted in which feed pressure, air pressure, rotary speed, weight on the bit, and torque were varied to measure their effect on the penetration rate. The uniaxial compressive strength varied from 90–180 MPa for layered marble-quartzite and banded gneiss. Increases in feed pressure, weight on the bit, and rotary speed beyond the optimum level led to a decrease in penetration rate and caused the drill bit to ‘stall’. Results of the study revealed that penetration rate increases with an increase in the feed pressure and air pressure. After reaching a maximum value, the penetration rate begins to decrease despite increasing feed pressure. A very high torque causes the drill bit to stall, since the feed pressure is too high and the air pressure is not sufficient to remove the cuttings from blast-hole at maxium bailing velocities. The average penetration rate varied from 19 to 45 m/h for phase 2 of the pit, and from 17 to 68 m/h for phase 3. The optimum drilling machine parameters obtained in phase 2 and phase 3 were slightly lower than those currently being used at the mine. The trials of the optimum machine parameters will assist in reducing the cost of drilling, which varied from N$29.48 to N$36.31 per metre for the tricone bit. IntroductionDrilling and blasting contribute most to the operational cost in opencast mining and have the potential to influence the cost of downstream operations (Aipanda, 2011). The drillability of rocks depends not only on the rock properties, but also on the drilling tools and operational variables. In rotary drilling, rotational speed, thrust, and flushing are the operational variables, and are known as the controllable parameters. Rock properties and geological conditions are the uncontrollable parameters. Although, many attempts have been made to correlate drillability with rock properties, the rock characteristics affecting rotary drilling have not been entirely defined (Hartman, 1962; Kahraman, Bilgin, and Feridunoglu, 2003). The drill bit is forced into a rock surface from the rotary power head, hence creating stresses and cracks at the bit-rock interface. The performance of a particular bit in any formation i"

May 1, 2019

By E. Lutz, M. Momayez, K. W. Brown Requist

As real-time air quality monitoring becomes more prevalent in US underground mines, it is important to provide the highest data reliability with the fewest possible sensors. Real-time sensors remain costly, and these costs are not exclusively financial; the time required to install, calibrate, and maintain real-time sensors poses a large barrier to widespread implementation. Current atmospheric monitoring systems typically rely on displaying point-specific values. This requires operators to infer real-time airborne contamination distributions. Monitoring and control software utilizing mine ventilation network (MVN) solvers has been implemented in limited cases because of their ability to simulate ventilation systems quickly, but these solvers use a one-dimensional representation of the mine, limiting spatial resolution of estimated distributions. Computational fluid dynamics (CFD) has likewise been considered as a means to improve spatial resolution, but processing times prevent its use as a basis for monitoring and control. For the real-time monitoring of airborne contamination distributions, we propose a spatial interpolation method that can estimate the distribution of airborne contaminants in near-real time. This method provides a middle ground between fast processing times and increased spatial resolution. With the use of a pathfinding algorithm and optimization through absolute percentage error minimization, this method outperforms spatial interpolation with a Euclidean distance. By providing contamination distribution information to operators, this method and its derivatives stand to outperform current atmospheric monitoring systems.

Apr 16, 2024

By T. Ito, N. Tokashiki, H. A. Bilgin, Ö. Aydan, T. Akagi

This study is concerned with the electric potential induced by deformation, fracturing and sliding of non-piezoelectric geomaterials. In experiments, the acoustic emissions together with electric potential measurements were also measured in order to see how the so-called seismic electric signals are associated with new fracture occurrence and propagation and sliding in case of existing discontinuities. The outcomes of this experimental study may explain why such electric potential variations may occur during the fracturing and sliding of non-piezoelectric geomaterials. On the basis of these outcomes, their possible implications in geo-engineering and geo-science are discussed. Ce travail concerne 1e potentiel électrique produit par la déformation, 1a fracture ou le glissement du matériel géologique non-piézoélectrique. Aux expérimentations, on a mesuré 1es émissions acoustiques avec le potentiel électrique afin de constater la relation entre les phénomènes de glissement ou de formation et de propagation de nouvelles fractures le long des discontinuités existantes. Les résultats de ce travail expérimental expliquent pourquoi de telles variations de potentiel electrique se produisent durant le glissement ou la fracture du matériel non-piézoélectrique. Sur la base de ces résultats, on a discuté de leurs éventuelles implications dans les domaines de 1a géologie et de 1a géo-ingénierie. Diese Studie befasst sich mit dem elektrischen Potential das durch die Deformation, Bruchbildung und Gleiten von nicht-piezoelektrischen Geomaterialien induziert wird. In Experimenten wurden die akustischen Emissionen zusammen mit elektrischen Potentialmessungen gemessen, um zu sehen, wie die so genannten seismischen elektrischen Signale mit neuer Bruchbildung und Ausbreitung sowie Gleiten im Falle von vorhandenen Diskontinuitäten verbunden sind. Die Ergebnisse dieser experimentellen Untersuchungen könnten erklären warum elektrische Potential Schwankungen während der Bruchbildung und dem Gleiten von nicht-piezoelektrischen Geomaterialien entstehen. Auf der Basis dieser Ergebnisse, wurden ihre möglichen Implikationen in Geoingenieurwissenschaften behandelt.

Jan 1, 2003

By R. Singh, A. K. Dhawan, M. Dixit, H. Dev

ABSTRACT: The modulus of deformation of rock mass is an important engineering parameter required for the design of foundation of hydraulic structure and to study the interaction of rock mass and the structure at the foundation support. Different equipment and techniques are used to arrive at the design modulus value. Since any error in the estimation of modulus values results in multiplication of its effects in the analysis, it is necessary to know about the reliability of testing equipment and procedures. In the present study modulus values obtained by different in-situ equipment at different project sites have been compared. KURZFASSUNG: Der Verformungsmodul von der Felsenmasse ist technisch ein wichtiger Parameter, den man zur Konstuktion des Grunds fuer die Hydro – Tektonik, benoetigt um auch die gegenseitige Beeinflussung der Felsenmasse und der Tektonik am Traggrund zu betrachten. Verschiedene Geraete und Methoden werden angewandt, um den Ausfuehrungsmodul -Wert zu erreichen. Es ist erforderlich, die Zuverlaessigkeit der Pruefeinrichtung sowie des Verfahrens zu kennen, da irgend ein Fehler in der Abschaetzung von Modulwerten in der Analyse zu einer Vervielfachung ihrer Einwirkung fuehrt. In der vorligenden Arbeit werden die Modulwerte gewonnen aus unterschiedlichen Einrichtungen an Ort und Stelle and verschiedenen Projekt -Stellen mit einander verglichen. SOMMAIRE: Le module de deformation d’une roche est un parametre important pour la conception et realisation des ouvrages hydrauliques ainsi que pour etudier l’interaction de la roche et de la structure d’appuis de base. De divers equipments et techniques sont employes pour determiner la valeur de ce module de conception. Puisque l’effet d’une erreur d’evaluation du module devient multiplie dans l’analyse, il est necessaire de savoir la fiabilite des equipments et des methods qu’on ulilise. Dans cette etude, on a compare les valeurs des modules obtenues en employant les equipments in-situ aux sites differents de projets.

Jan 1, 2003

By R. A. Wildenboer, R. F. Sandenbergh

Rare earth elements (REE) are present at concentrations of approximately 0.36 % in phosphogypsum stacks located in Phalaborwa, South Africa. The REE are present in the phosphogypsum in solid solution in the gypsum and as fluorine and aluminium rich precipitates. Recovery of the REE offers opportunities for valorization and reducing the environmental impact of the phosphogypsum waste. This paper presents the results of investigations into the leaching behaviour of rare earth elements and other impurities from phosphogypsum using aqueous sulfuric acid. The effects of acid concentration, temperature, residence time, and the influence of impurities were evaluated for their impact on the solubility of rare earth elements in a sulfate medium. It was found that a significant fraction of the REE can be leached from the phosphogypsum in a range of conditions much less severe than traditional hard rock rare earth processing conditions. The REE were leached at a sulfuric acid concentration of 110 g/l, temperature of 30°C – 40°C and a residence time of approximately 8 hours.

Nov 6, 2024

By D. Nardini

The need to move towards faster and safer mine development is a key priority in mining houses globally. In addition to this, South Africa faces an array of challenges introduced by labour-intensive operations; hence a study was conducted to look into improving development rates and labour productivity, specifically in the areas where trackbound flat-end development is required. The aim of the study was to propose a method to deliver fit-for-purpose tracked tunnels that advanced at a rate of one blast per end every single working day. A major part of the study was to optimize the selection of an appropriate trackless fleet and mitigate any constraints introduced with the mechanization. This was done by creating scenarios, based on a typical case study, looking into the aspects around safety, mine design, mine activity cycling, men and machine requirements, service installations, and trackless-trackbound interfaces. The case study was based on a deep-level gold mine developing twin headings with connectings; however, with the move to extend and deepen platinum operations it is foreseen that twin end development will become more prevalent due to ventilation, logistical, and other requirements. With the introduction of the trackless mechanized system suggested, development rates of 56 m of system advance are expected (189 m total development), with on an average of three headings and fixed blast times. Scenarios run with multi-blast conditions yield expectations of 75 m/month advance of the system, significantly higher than the conventional performance seen today.

Jan 1, 2012

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

Blaine number has long been used to evaluate the pelletising ability of iron concentrate in the industry. Much information and practical data are available about the effect of Blaine number on pelletising efficiency of different concentrate types. But not many researchers have focused on the effect of Blaine increasing method on pelletising behaviour of coarse concentrates. In this paper the effect of two different grinding methods (i.e. HPGR and Ball Mill) on physicochemical properties of coarse magnetic concentrate green and fired pellets were investigated. Microstructural studies by Field Emission Scanning Electron Microscope (FESEM) showed that the concentrate for which the Blaine number had been increased through HPGR grinding, has flake-like morphology. In contrast, increasing the Blaine number through ball mill grinding results in more granular particles. Two samples were prepared using HPGR and ball mill. The Blaine number of the HPGR product and ball mill product were 900 cm2.gr-1 and 1200 cm2.gr-1 respectively. The results revealed that pellet properties of this HPGR product are comparable to that of the ball mill product; this is due to the fact that the flake-like morphology leads to enhanced pelletising performance of coarse magnetite concentrates. Keywords: Iron pelletising, Blaine number, HPGR, ball mill, coarse particles

Jan 1, 2020

By J. W. Klokow, S. L. Mulder

Early removal of the shaft reef is usually considered necessary on deep level South African gold mines to avoid damaging stress build-up associated with traditional shaft-protection pillars. In the case of the relatively shallow Beatrix Gold Mine it was largely motivated by early access to ore and the consequent earlier return on invested capital. A number of options were considered to protect the shaft from possible damaging stress changes and to minimise deformations in the shaft-reef area. Numerical modelling was used to evaluate the options and to quantify as accurately as possible the likely deformations to be accommodated by the shaft steelwork designs. The option chosen was a combination of strategically placed satellite pillars and yield pillars, and backfill. Following the mining of a small inner cut during the shaft sinking process, full-scale mining is progressing away from the shaft. Suitable instrumentation has been installed to monitor deformations associated with the shaft reef removal. Enlever rapidement le filon du puits est en général considéré nécessaire dans les galeries de fond des mines d’or sud-africaines pour éviter l’accumulation nuisible de contraintes associée aux piliers de protection de puits traditionnels. Dans le cas de la mine d’or Beatrix, relativement peu profonde, l’enlèvement était motivé en grande partie par l’accès rapide au minerai et par conséquent un profit plus rapide sur l’investissement. Un certain nombre d’options furent considérées pour protéger le puits contre les changements de contraintes potentiellement nuisibles, et pour minimiser la déformation dans l’aire puits/filon. La modélisation numérique fut utilisée pour évaluer les options et pour quantifier aussi précisément que possible les déformations probables que la conceptualisation du puits devrait prendre en compte. L’option choisie fut une combinaison de piliers satellites placés à des points stratégiques avec des piliers de protection, et terre de remblayage. Pendant le fonçage de puits une petite coupure intérieure fut exploitée, et maintenant l’exploitation à grande échelle, au-delà du puits, est en cours. Les instruments nécessaires ont été installés pour surveiller les déformations associées à l’enlèvement du filon du puits. Die frühe Entfernung des Riffschachtes wird normalerweise bei südafrikanischen Tiefbaugoldmienen als notwendig erachtet um den zerstörende Druckaufbau zu vermeiden, welcher mit traditionellen Schachtschutzpfeilern verbunden ist. Im Fall der verhältnismäßig flachen Beatrix Goldmine war es hauptsächlich vom frühen Zugang zum Erz und dem konsequenten frühen Rückfluß des investierten Kapitals motiviert. Eine Anzahl an Optionen wurde erachtet um den Schacht vor möglichen zerstörenden Druckänderungen zu schützen und Deformationen im Riffschachtbereich zu minimieren. Um die Optionen zu bewerten und mögliche Deformationen so genau wie nur möglich quantitativ darzustellen die von den Schachtstahlkonstruktionen aufgenommen werden müssen, wurden numerische Modelle verwendet. Die gewählte Option war eine Kombination aus strategisch plazierten exzentrischen Pfeilern und Schutzpfeilern sowie Hinterfüllungen. Nach dem Vortrieb eines kleinen inneren Einbruches während des Abteufens wird der Vollvortrieb vom Schacht weg vorgenommen. Um die Deformationen, die mit der Riffschachtentfernung verbunden sind zu überwachen, müssen geeignete Instrumentenausrüstungen installiert werden.

Jan 1, 2003

By F. Pinto, J. V. Lemos, A. Sousa, L. Ribeiro e Sousa

The Rossio railway tunnel was built in 1890 crossing several formations involving limestones, basalts and also sandy and clayey formations. Due to the fact that it is an old underground structure rehabilitation and repair works were performed, namely at Km 0,900 and in a zone crossed by a new tunnel from the Lisbon Metro. Reinforcement support systems were designed in the Rossio tunnel in order to prevent its stability. In this paper, repair works and anchor tests performed at km 0,900 are presented, as well as the monitoring system implemented in order to observe the structural effects induced by the construction of the works. For the interpretation of the obtained information complex 3D models was built, permitting the simulation of the sequential excavation scheme used, non-linear behaviour of the different formations, and the support systems used. Der 1890 erbaute Rossio Eisenbahntunnel durchoertert mehrere Formationen, einschliesslich einer Kalkstein-, Basalt- sowie einer sandigen und tonigen Formation. Auf Grund des Alters des unterirdischen Bauwerks wurden Instandsetzungs- und Reparaturarbeiten im Bereich km 0,900 sowie im Kreuzungsbereich mit einem neuen Tunnel der Lissabonner U-Bahn durchgeführt. Aussteifungssysteme wurden entworfen, um die Stabilität des Rossio Tunnels zu gewährleisten. Im Folgenden werden die Instandsetzungsarbeiten und Anker Tests im Bereich km 0,900 sowie das Messystem zur Ueberwachung der strukturellen Auswirkungen der Bauarbeiten dargestellt. Zur Interpretation der gewonnenen Informationen wurden komplexe 3D Modelle entwickelt, die eine Simulation des Bauablaufs und die Anwendung nichtlinearer Stoffgesetze fuer die verschiedenen Formationen und Aussteifungssysteme ermöglichten. Le Tunnel ferroviaire du Rossio a été construit en 1890, traversant des différents terrains comme des calcaires, des basaltes et aussi des formations limoneuses et sableuses. Dû à l’ancienneté de l’ouvrage, des travaux de réhabilitation et réparation ont été faits, nomment au km 0,900 et dans la zone traversée par le nouveau tunnel du Metro de Lisbonne. Des systèmes de support renforcé ont été conçus pour le Tunnel du Rossio de façon à rassurer sa stabilité. Dans ce papier, on présente les travaux de réparation et les essais d’ancrage réalisés au km 0,900, et aussi, le système d’auscultation mise au point pour l’observation des effets structuraux induits par les travaux. De façon à interpréter l’information résultant de l’observation, des modèles 3D complexes ont été utilisés, permettant la simulation de la méthode séquentielle de l’excavation, du comportement non - linéaire du terrain et, aussi les systèmes de support utilisés.

Jan 1, 2003

The February General Meeting of the Branch was held at the St. Helena Club on Wednesday, 19th February, 1969. Present were: Twelve members: Mr J. G. Kirchner (Chairman of the O.F.S. Branch), Messrs J. N. Saunders, N. A. Honnet, L. O. W. Leimer (Committee Members), Messrs R. C. Espley-Jones, J. W. Wilson, A. T. Lewis, A. von Holdt, L. J. Thorne, C. Mostert, V. O. Steed, H. H. Schellhorn. Nine Associate Members: Messrs E. R. Penny, G. T. C. Emere, M. Forster, K. Pearce, R. B. Sutherland, D. E. Couperthwaite,A. H. Edwards, M. D. de Lange, G. ,R. Still. Four Graduates: Messrs M. H. Smith, N. Mayer, T. R. Stromsoe, T. A. Ward. Four Affiliates: Messrs D. S. Robinson, L. D. Hulley, R. B. Smith, R. L. Soll11s.One Student: D. R. Fleming. Twenty-three Visitors. Total present: 53. Apologies were received from Messrs C. R. Netscher, A. Leger and V. C. Barnes. MINUTES OF PREVIOUS GENERAL MEETING The minutes of the General Meeting held on 15th November, 1968 and which were published in the February Journal, were taken as read and their adoption moved by Messrs J. N. Saunders and N. A. Honnet. There were no matters arising from the minutes. GENERAL BUSINESS The Chairman reminded members of the forthcoming visit by the Branch to the Dudfield Works of the Anglo-Alpha Cement Company, to take place on Wednesday 16th April. TALK ON ROCK MECHANICS The Chairman called upon Mr J. W. Wilson to address the meeting on the subject of the practical applications of rock mechanics to mining. Mr Wilson used a slide projector to present his subject in a most interesting and instructive manner which eventually resulted in much useful discussion taking place. The Chairman then called upon Mr A. von Holdt to thank the speaker. CLOSURE After thanking the speakers, the Chairman thanked members and visitors for their attendance and closed the meeting at about 10 p.m., after which refreshments were served.