Search Documents

By D. Butler

Lateral density changes in the subsurface cause a change in the vertical pull of gravity at the surface. By very accurate measurement of gravity and the practical application of common sense, a microgravity survey can sometimes detect natural or man-made voids, bedrock profiles, and geologic structures of engineering interest. This paper will give some practical guidelines for the application of microgravity surveying. Emphasis in many papers (Blizkovsky, 1979, Fajklewicz, 1983) has been on the anomaly size: herein emphasis will be placed on detectability and signal-to-noise ratios. First, some easy to use curves for anomaly valuation are adapted from Arzi (1974). Secondly, the predictable noise sources are discussed. Thirdly, representative models of abandoned underground workings are evaluated for microgravity surveying given the probable noise in the survey results.

Jan 1, 1988

By K. Oraee

Excessive emissions of methane from the coal seams can have a serious adverse effect on both safety and productivity of longwall coal faces. Mechanization of coal faces has increased production possibilities to the extent that normal ventilation systems may not be able to ventilate coal face areas in order to lower methane content in the air to within legal limits. Production increases may therefore be prohibited for this reason, especially in gassy seams. Methane drainage from the coal seam by means of long holes and before production starts can act as a useful remedial action. In this paper a two dimensional mathematical model has been produced. The model that is based on finite elements, simulates a methane drainage system where the resultant risk is linked to the coefficient of diffusion, coal permeability, holes pattern and the duration for which the seam is subject to drainage. It is concluded that methane drainage of this type can assist in achieving production increases in many coals seems, especially where high gas content is a virtue of the seam.

Jan 1, 2010

By D. A. Norrgran

The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980's provided a magnetic energy product an order of magnitude greater than that of conventional ferrite magnets. This has allowed the design of high-intensity magnetic circuits operating energy free and surpassing the strength and effectiveness of electromagnets. New applications and design concepts focused on the mineral and metal processing industries have evolved. This technology also led to the development of various magnetic separators specifically designed for mineral processing applications. Applications which were not previously considered are now being applied to primary mineral upgrading and recycling and secondary recovery.

Jan 1, 1993

By D. H. Lynch

This paper is a general description of current Central Florida phosphate mining, beneficiation and product transportation. It is directed and believed to be of interest to engineers not familiar with this industry.

Jan 1, 1978

By P. C. Clark

This paper is an overview of the requirements and concerns for minerals and pigments used in papermaking. The first part of this paper deals with mineral or pigment filling in the actual papermaking process. The second part deals with the pigment or mineral properties that are important in today's coating processes.

Jan 1, 1993

ABB Industrial Systems is one of the largest electrical engineering companies in the world. ABB develops, manufactures and markets electric drives. The company has more than 100 years experience in the application of medium- and high-voltage AC machines. And ABB's continuous research and development program ensures that its machines use the latest technologies and materials. Each motor is custom designed to meet specific applications. The HXR high-efficiency motors (100 to 1,900 kW or 134 to 2,250 hp at 50 Hz) are efficient and have low noise levels. Typical applications are pumps, fans, blowers, compressors and pulverizers. The enclosed units are constructed with external cooling ribs and fans. And the motors are equipped with solid, longlife stators and rigid rotor construction. The patented rotor construction provides for low vibration levels. ABB's large synchronous motors (1 to 50 MW or 1,340 to 70,000 hp up to 900 rpm) are used in the mining industry for crushing, grinding hoisting and conveying systems. These motors are designed to customer's specifications, including existing foundations. They can be equipped with fixed or adjustable speed control.

Jan 1, 1998

By Barnaby J. Watten, Sibrell. Philip L., Brian J. Vinci, Andrew E. Friedrich

We evaluated a new process for remediation of acid rock drainage (ARD). The process treats ARD with intermittently fluidized beds of granular limestone maintained within a continuous flow reactor pressurized with CO2. Tests were performed over a thirty day period at the Toby Creek mine drainage treatment plant, Elk County, Pennsylvania in cooperation with the Pennsylvania Department of Environmental Protection. Equipment performance was established at operating pressures of 0,34,82, and 117 kPa using an ARD flow of 227 L/min. The ARD had the following characteristics: pH, 3.1; temperature, 10 OC; dissolved oxygen, 6.4 mg/L; acidity, 260 mg/5; total iron, 21 mg/L; aluminum, 22 mg/L; manganese, 7.5 mg/L; and conductivity, 1400 uS/cm. In all cases tested, processed ARD was net alkaline with mean pH and alkalinities of 6.7 and 59 mg/L at a CO2 pressure of 0 kPa, 6.6 and 158 mg/L at 34 kPa, 7.4 and 240 mg/L at 82 kPa, and 7.4 and 290 mg/L at 117 kPa Processed ARD alkalinities were correlated to the settled bed depth (p<0.001) and CO2 pressure (p<0.001). Iron, aluminum, and manganese removal efficiencies of 96%, 99%, and 5%, respectively, were achieved with filtration following treatment. No indications of metal hydroxide precipitation or armoring of the limestone were observed. The surplus alkalinity established at 82 kPa was successful in treating an equivalent of 1136 L/min (fivefold dilution) of the combined three ARD streams entering the Toby Creek Plant. This side-stream capability provides savings in treatment unit scale as well as flexibility in treatment effect. The capability of the system to handle higher influent acidity was tested by elevating the acidity to 5000 mg/L with sulfuric acid. Net alkaline effluent was produced, indicating applicability of the process to highly acidic ARD.

Jan 1, 2000

By B. K. Cantrell, D. H. Carlson, W. F. Watts, K. L. Rubow

The use of diesel equipment in underground coal mines is controversial because the National Institute for Occupational Safety and Health (NIOSH) regards "whole diesel exhaust" as "a potential occupational carcinogen." Threshold limit values (TLVs) are recommended for the gaseous pollutants CO, CO2, NO, N02, SO2 and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols. The University of Minnesota and the USBM have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) that utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines that used diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality. Air quality data were collected in four underground coal mines. The mines used continuous miners and diesel haulage equipment. Daily samples were collected at the section intake, haulageway and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments. These included the PDEAS and the micro-orifice uniform deposit impactor (MOUDI) that sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2 and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters. Concentrations of CO, C02, NO, NO2 and SO2 were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3.

Jan 1, 1992

By H. F. Broicher

Introduction In April 1998, AIS Sommer GmbH of Germany delivered the first laser-induced fluorescence (LIF) analyzer to the mining industry. LKAB&apos;s Kiruna iron ore mine in Sweden shared the costs and the risk of building the prototype. This marks the beginning of LIF analysis as a technique for quality control in mining and mineral processing. Photoluminescence analysis is well established. In most laboratories, fluorescence spectrometers are standard equipment for quality or pollution control. LIF is being used in several applications, including combustion studies and particle image velocimetry. However, it has mostly been used in laboratory environments. The availability of rugged lasers for industrial use brings this powerful tool to the forefront of production, even in the rough conditions found in mining and minerals processing. Laser-induced fluorescence Basics. Fluorescence of naturally occurring minerals has fascinated man since scientific investigation of this phenomenon commenced about 200 years ago. However, importance in industrial application and peripheral activities. Hand sorting of ore under ultraviolet (UV) lamps is seen as an archaic method. Long gone are the days when geologists set out at night with UV hand lamps to find valuable ore deposits, especially those of tungsten. Today, fluorescent minerals are considered collectors&apos; items and museum exhibits. In the late 1960s (Hemphill, 1968) and during the 1970s, attempts to use lasers for excitation of fluorescence in minerals led to the development of an airborne fluorosensor (Seigel and Robbins, 1980). However, this prospecting technology did not gain industry acceptance and vanished from the market. During the past seven years, ongoing research of the LIF of minerals resulted in new findings that give good reason to revive the interest in fluorescence and its use in the mineral industries (Broicher and Zydek, 1995; Broicher, 1998). Fluorescence is defined as the short-lived form of photoluminescence, in which matter emits visible radiation during and after irradiation with light – the fluorescence generally being of a longer wavelength than the irradiation. Fluorescence of matter is described by: • the absorption spectrum, • the emission spectrum, • the decay curve and • the quantum efficiency. The absorption spectrum shows the fluorescence intensity in a fixed spectral band as a function of the excitation wavelength, while the emission spectrum shows the fluorescence intensity at varying emission wave- lengths for a fixed excitation wavelength (Fig. 1). The decay curves describe the exponential decrease of the fluorescence intensity with time. The quantum efficiency is the ratio of irradiating energy to emitted energy. Re- cent research has found that: the quantum efficiency of minerals can be measured and evaluated,

Jan 1, 2000

By S. G. Hardcastle, K. C. Butler, M. G. Grenier

The most common method of determining airflow employed by mine ventilation engineers is the product of i) the average air velocity as measured by a vane anemometer and stopwatch through a continuous traversing technique, with ii) the cross-sectional area of the roadway. This method requires the vane anemometer to accumulate the total flow over the duration of the traverse. Historically, this has been facilitated by a mechanical analog instrument that has either a counter or set of dials that display the flow. Common instruments of this type are Airflow Development&apos;s AM5000, Davis&apos;s, or Taylor&apos;s Biram type anemometer. The AM5000 is widely used in the Canadian mining industry but is no longer available. Therefore, regulatory authorities have seen fit to evaluate presently available commercial instruments to replace the AM5000. This paper describes an instrument evaluation contracted by the Atomic Energy Control Board of Canada which regulates the uranium industry. Over the last two decades there have been numerous advances in the development of electronic air velocity meters. Currently available units have the following features: a) battery operation; b) are compact and can be hand-held; c) employ LCD&apos;s, and microelectronic circuitry; and d) provide a time integration for the duration of a traverse. These features make such instruments a possible replacement to the analog units and stopwatch determinations. This paper details five of the new generation of vane anemometers plus a vortex air meter, and it explores their limitations in comparison to analog units. Specific consideration is given to linear response, the effects of yaw, traversing speeds and ergonomics relating to both handling and use. The paper concludes with some features that are attractive and should be considered when purchasing a new anemometer.

Jan 1, 1991

By J. Simmons, P. Ziemkiewicz

Acid-Base Accounting (ABA) is an analytical procedure that provides values to help assess the acid-producing and acid-neutralizing potential of overburden rocks prior to coal mining and other large-scale excavations. This procedure was developed by West Virginia University scientists during the 1960s. After the passage of laws requiring an assessment of surface mining on water quality, ABA became a preferred method to predict post-mining water quality,and permitting decisions for surface mines are largely based on thevalues determined by ABA. In order to predict the post-mining water quality, the amount of acid-producing rock is compared to the amount of acid-neutralizing rock, and a prediction of the water quality at the site (whether acid or alkaline) is obtained. We gathered geologic and geographic data for 56 mined sites in West Virginia, which allowed us to estimate total overburden amounts, and values for maximum potential acidity (MPA), neutralization potential (NP), net neutralization potential (NNP), and NP/MPA ratios for each site based on ABA. These values were correlated to post-mining water quality from springs or seeps on the mined property. Overburden mass was determined by three methods, with the method used by Pennsylvania researchers showing the most accurate results to actual overburden mass. A poor relationship existed between MPA and post-mining water quality, NP was intermediate, and NNP and the NP/MPA ratio showed the best prediction accuracy. In this study, NNP and the NP/MPA ratio gave identical water quality prediction results. Therefore using NP/MPA ratios, values were separated into categories: <1 should produce acid drainage, between 1 and 2 can produce either acid or alkaline water conditions, and >2 should produce alkaline water. On our 56 surface mined sites, NP/MPA ratios varied from 0.1 to 31, and six sites (11%) did not fit the expected pattern using this category approach. Two of eight sites with ratios <1 did not produce acid drainage as predicted (the drainage was neutral), and four of 40 sites with a ratio >2 produced acid drainage when they should not have. These latter four sites were either mined very slowly, had non-representative ABA data, received water from an adjacent underground mine, or had a surface mining practice that degraded the water. In general, an NP/MPA ratio of <1 produced acid or neutral drainage sites, between 1 and 2 produced mostly alkaline drainage sites, while NP/MPA ratios of >2 produced alkaline drainage with a few exceptions. ABA is a good tool to assess overburden quality before surface mining and to predict post-mining drainage quality after mining. The interpretation from ABA values was correct in 50 out of 52 cases (96%), excluding the four anomalous sites, which had acid water for reasons other than overburden quality.

Jan 1, 2003

By Ian S. Lowndes, Adrian T. J. Moll

With the current trends towards the concentration of extraction to fewer but higher production units in deeper seams, often of higher coal rank, the role of methane drainage ranges has become critical. As mines exploit seams at greater depth and more remote locations there has been a need to extend the lengths of methane drainage ranges and to increase the capacity of the surface pumps. This trend has highlighted the need to effectively simulate the operation of a methane drainage range in order to produce the optimum design and operation of a safe and economic system. This paper describes the development of such an analytical tool. The application of this computer model is illustrated by the analysis of the operation of the drainage system of an extensive mine. The paper concludes by considering the development of a [Knowlege Based or Decision Support System] which will assist the ventilation engineer in assessing the current performance of an existing drainage range and will suggest possible remedial modifications or design strategies which may improve the system performance. INTRODUCTION In order to maintain the general body methane levels to below predetermined statutory threshold limit values (TLV&apos;s) on major longwall production units there are, for a given production rate, two major complementary control devices which may be employed by the ventilation engineer. These are the combined design and application of a competent mine ventilation and methane drainage system. The methane drainage system should be designed so as to maximise the capture of the methane (firedamp) from the seam being mined and the strata gas liberated in the vicinity of the extraction zone from gas bearing seams or other reservoirs of gas situated at above or below the mining horizon. The design fresh air quantity entering the face should ensure that under normal operating conditions the methane entering in the vicinity of the face is rapidly dispersed and dilute to well below statutory TLV&apos;s. The drainage system must therefore be designed to maximise the capture of the methane gas liberated to minimise the amount of gas which enters the ventilation airstream. GAS DRAINAGE The inherent dangers of methane emissions in mine workings have been a problem of concern to mining engineers for many years. To alleviate the risk, methane drainage has been employed for some years to capture the gas before it becomes a hazard to the operation of the mine. The method of drainage employed will be dependent on a number of factors which include the longwall mining method and production cycle employed, the characteristics of the coal seam being extracted and those of the adjacent gas bearing strata. The location of the gas bearing potential of the over and underlying coal measures must be determined. The gas bearing

Jan 1, 1993

By Hugh E. Cronin, Joseph J. Coluccio

The Columbia Slough Consolidation Conduit Project is a 12 ft. 0 in. inside diameter—15 ft. 4 in. excavated diameter tunnel, 8,300 lf. in length. The tunnel is divided in two parts a 4,460 lf. reach to the West and a 3,770 lf. reach to the East separated by a flow regulation structure in the middle. The project was built for the City of Portland, Oregon Bureau of Environmental Services (BES) by the Frank Coluccio Construction Company (FCCC) Seattle, Washington under a $22,600,000.00 contract starting in 1998 and completing the contract in 2000 at a total cost to the City of $25,448,000. An increase of 12.6% from the original contract. The tunnel was constructed in an alluvial sediment that ranges up to 1,500 feet thick. The sediment varies from ?ne silty sand and sandy silt (SM-ML) to coarse sand and gravel (GP-GM) with varying quantities of cobbles and boulders. Most of the tunnel was constructed above the water table although one reach of almost 1,000 lf. had water to above the tunnel crown. The contractor, FCCC, used a Lovat 15 ft. 3 in.900 hp shielded TBM with multiple doors (4) of variable opening to excavate and support the tunnel. Tunnel supports were 5 in. WF 16 lbs. per foot at 4 ft. spacing and4 in. Douglas Fir lagging. Tunnel excavation was worked in 10 hour shifts with additional equipment maintenance and repair on the off time. The original Geotechnical Design Summary Report (GDSR) established a baseline for contractual purposes of slightly over 5 boulders (between 12 in. and48 in.) per foot of tunnel. (Table 1) At the pre-bid conference, three test pits were excavated to approximately tunnel invert, one at each end of the project and one in the middle near the flow regulation structure. The test pits encountered a few boulders but did not seem to support the five boulders per foot (varied from one boulder per foot of tunnel to eight b/lf.). Subsequent to the pre-bid meeting and the test pits, BES issued any addenda which changed the baseline boulder quantity in the GDSR to 1.7 boulders per foot of tunnel (varied from0.2 to 3.5 boulders per foot) a reduction of 67% from the original baseline. It is interesting to note the two separate tunnel reaches and how they were evaluated in the GDSR. Originally the Eastern portion of the work was projected at5.08 boulders per foot of tunnel and the Western portion at 5.30 boulders per foot of tunnel for a variance of less than 5%. In the revised quantity the Eastern portion was projected at 2.01 boulders per foot of tunnel and the Western portion at 1.42 boulders

Jan 1, 2003

By R. H. King, D. R. Schricker, R. E. Cameron

Mine managers rely on their experience, section foreman&apos;s daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today&apos;s highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.&apos;s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment. Western Fuels-Utah owns and operates the Deserado Mine, located about 19 km (12 miles) northeast of Rangely, CO (Upadhyay, 1988; King and Eros, 1988). One longwall and two continuous miner sections produce about 900 kt (1 million st) of coal annually for the Deseret Generation and Transmission Cooperative&apos;s 4000 MW power plant located near Bonanza, UT. Three mine monitoring systems control the underground mine, the preparation plant and the unit train load out. Pattern recognition IDSS/PRS produces a listing of begin and end times for each machine operating event as shown is Table 1.

Jan 1, 1991

By Joseph L. Walker

INTRODUCTION In looking over the diversity of the papers that are being presented during this meeting on The Industrial Practice of Fine Coal Processing one cannot help but be impressed with the progress the industry has made in beneficiating fine raw coals, and in the number of innovations that are under study to increase recovery and to improve the quality of the finest size particles produced at a preparation plant. Those who are not in our industry, who look at the technical program, might be confused, when they see that the papers include such topics as cleaning to zero and heavy media cyclone cleaning 28M x 100M; application and performance of fine coal jigs, tables, hydrocyclones, spirals, and flotation; filtration, dewatering and thermal drying; and ancilliary aspects such as fines handling, instrumentation and process control plus screening and liberation. This is an observation and not a criticism of the diversity of papers being presented. The program fits within the parameters of fine coal preparation as the term "coal preparation" is defined, but perhaps not as the term "fine coal" is defined. Admittedly these definitions are sometimes loose. However, each should be made more definitive if a meaningful fine coal preparation overview is to be possible. COAL PREPARATION DEFINED In the opinion of the writer, the term "coal preparation" should be defined as including all work activities that are performed on all components of a run-of-mine coal from the time it leaves a surface reserve or an underground portal, until all components are either ready for shipment or are stowed on, or in the earth in an environmentally acceptable manner. This definition excludes the work that is performed to improve coal quality or handleability inside the mine or pit. This work is commonly called "face" or "pit" preparation. FINE COAL DEFINED The term "fine coal" means different things to different people. In the past, anthracite finer than No. 3 Buckwheat (3/16 in.) was considered fines which often were discarded from the breaker as an unsalable by product; and bituminous coals finer that about 1/4 in. (slack) were either discarded or sold at cost to prevent an accumulation of "no bills" which referred to a product having no immediate sale. Although a standard definition of "fine coal" is yet to be accepted by the industry, a designation of coals by particle-size range has evolved through the wide use of three-circuit flowsheets, wherein the optimum size range by washer type determines the size fractions: a coarse-coal circuit for the plus 3/8 in., a -11- coal circuit for the 3/8 in. x 28 Mesh, and a fine-coal circuit for the remaining 28 Mesh x 0. Logically, the term "fine coal" should refer to some resultant size fraction or some top size by zero. This definition should include a 28 Mesh x 0 feed to a flotation cell but should exclude a 28 x 100 Mesh size fraction fed to a heavy media cyclone. Failure to include the resultant sizes in the definition precludes accounting of the full range of particle sizes present in the feed to the plant. Since the 28 Mesh x 0 fraction is treated in the final circuit of the three discreet washing circuits, now almost always used in U.S. commercial applications, and since it contains all of its resultant sizes, in the writer&apos;s opinion, it should be designated "fine coal". FINE COAL CLEANING Cleaning coal fines, which in the past was at best marginally profitable, is now an essential part of coal preparation strategy for a number of reasons : 1. Raw coals now cost more to produce and

Jan 1, 1988

By A. G. Kim

Increasing transportation costs, clean air regulations and the decreasing availability of landfill space are factors in the increased interest in the utilization of low cost disposal sites for coal combustion residues (CCR). Inactive surface and underground coal mines can satisfy the conditions for stable CCR disposal sites, and subsurface CCR injection can be beneficial in reducing the amount of acid mine drainage (AMD) often produced at such sites. The material is expected to add alkalinity to the subsurface environment and to decrease the permeability and porosity of the buried spoil. Both mechanisms can reduce the amount of acid normally generated at a mine site. The Bureau of Mines is cooperating with an independent coal company in a test of subsurface injection of a mixture of fly ash, from conventional power plants or from fluidized bed combustion (FBC) , with AMD sludge into a reclaimed surface mine. Changes in water quality parameters and the concentration of heavy metals in water samples from wells and seeps are being used to assess the effect of CCR injection. The preliminary results discussed here indicate that improvement in subsurface water quality was related to fly ash injection and that components of the fly ash were stable in the acid environment.

Jan 1, 1994

By Ian S. Ross

The emphasis in this paper is focussed on dry bulk car go or the same cargo converted to slurry form for ease of handling. It is this type of cargo which is of primary interest to the mining industry whose products it represents to a large extent. The design problems associated with the handling of liquid bulk and of unitized cargo are sufficiently different to be treated separately. This paper then will consider the port handling facilities of dry bulk commodities as part of a system consisting of (1) the movement of products to the port area, (2) the movement of products out of the port area and (3) the handling of products within the port area itself. Expanding within these three components of the total transportation system, the paper will discuss the various difficulties encountered concerning the mode of transport into the port area and the method of handling product from transport to stockpile. Secondly, and before discussing the port area itself and in order to complete the conditions under which the port must operate, the movement of products out of the port area will be covered dealing with such items as the accommodation of the ship, problem associated with the very large ships, optimum berthing arrangements and the need to consider the various costs associated with the vessel. Finally the paper will review within the port or interface area such items as stockpiles, method of recovery, inventory control and an outline of the common design difficulties encountered. In all cases the relative influence on the total transportation costs of each of these dry bulk transportation system components will be considered.

Jan 1, 1972

By V. P. Petrov, V. S. Znamensky

There are a great number of asbestos deposits in the USSR, and some are quite large. The main deposits of chrysotile asbestos are shown in Fig. 1. The Bazhenovo deposit, which is located in the Sverdlovsk region, is the largest and has been mined since 1889. Systematic studies of asbestos deposits were begun from the very be- ginning of Soviet government and are most often connected with the names K.E. Tarasov, P.M. Tatarinov, B.J. Merenkov, N.D. Sobolev, F.V. Syromjatnikov, V.N. Lodochnikov, V.P. Petrov, V.P. Eremeev, L.A. Sokolova, V.R. Artemov, and V.F. Dybkov. Investigations by these people and others helped the USSR be one of the most important producers of asbestos in the world. In this chapter, the main asbestos deposits of the USSR are explained in a general outline from the point of view of their genesis, common features, and differences that must be taken into account for forecasting, exploration, and the mining of asbestos. All chrysotile asbestos deposits of the USSR were formed from magnesium rock as a result of comparatively low grade temperature, hydrothermal alteration, and free crystallization of fibrous chrysotile in open cavities that served as catalysts. Chrysotile, a widely distributed rock-forming mineral, is not in general an important mineral for industry as it is a long fibrous and main vein variety. However, it must serve for geologists as an important prospecting criteria. And, the geologist should search for the mineral not only in places of possible chrysotile generation, but in places where asbestos may be crystallized in its long fibers. The Soviet geologists distinguish chrysotile asbestos deposits in two groups: (1) ultrabasic rocks and (2) sedimentary dolomite terranes, taking into account how the maternal rock was affected by hydrothermal solutions. The largest deposits are related to ultrabasite. In dolomite, the largest deposits are small and their asbestos contains almost no iron, which makes it a better filler for insulating plastics. There are a few types of asbestos deposits within the limits of the ultrabasic group, the largest being a Bazhenovo type to which the deposits of the Urals are attributed. This Bazhenovo asbestos is characterized by the most complete zonality of disposition for various kinds of asbestization. These types of deposits are, for the most part, the only ones presently working in the USSR. The Bazhenovo deposit is connected to the gabbro-peridotite intrusive belt that is about 180 km long and is broken into a number of fault blocks as shown in Fig. 2. Granitoid veins of intruded rocks are found along the deepest faults, and were sources of hydrothermal solutions that affected the maternal rock. The nearest granitoid vein, ultrabasite, is substituted by listwanite that consists of quartz, talc, carbonate, and some other essentially talcous rock. The next zone of hydrothermal alteration is composed of serpentine. The boundry between serpentinite and unaltered ultrabasite is as irregular, diffuse, and rough as the boundaries between all other zones. Nearer the vein of granitic rock, ultrabasite is entirely serpentinized into massif serpentinization that penetrates through cracks and fissures. There is an unaltered ultrabasite space between fissures, and the biggest block is preserved unaltered in the central part of the massif. The Soviet geologists call this ultrabasic sopka. Preservation of the unchanged blocks is of great importance for deposit formation as volume changes are impossible during the process of asbestization and serpentinization. It may be confidently said that asbestization in Bazhenovo type deposits is possible only when alteration of ultrabasite has not completely occurred. Under conditions of massif volume, a very big mass of substance must be carried out of the ultrabasite for the progressive stage of serpentinization. However, in the regressive stage,

Jan 1, 1986

By Roger A. Kauffman, Dean Van Dyk

Feldspar is the earth&apos;s most abundant mineral group. The feldspars are aluminum silicate minerals belonging to the tectosilicate class. Feldspars are the most widespread of any mineral group and are estimated to constitute 60% of the earth&apos;s crust. They make up a large percentage of the exposed rocks as well as soils, clays, and other unconsolidated sediments. Feldspars are widely used in the glass and ceramic industry and are principal components in rock classification schemes. Feldspar minerals and their production are important contributors to the domestic and world economies and standard of living. In 1990, the United States produced 630 kt of feldspar minerals, and world production was estimated to be more than 5 Mt. Feldspar mineral production in the United States has a long and interesting history (Feitler, 1967, Rogers Jr. et al., 1983). The first commercial production in the United States occurred in about 1825 and came from pegmatite bodies located in Connecticut, where feldspar was mined, hand sorted, and shipped to England. Feldspar production grew during the 19th and 20th centuries with important developments in production location, integrated mine and processing facilities, and the development of the flotation process for feldspar by the US Bureau of Mines and the feldspar industry. The first commercial feldspar flotation plant began operations-in Kona, NC, in 1946, some six years after this process had been developed. In 1990, the domestic feldspar industry consisted of 12 operating companies with mines and processing plants located throughout the United States (see Table 1). During the last 25 years, the domestic feldspar industry has been dynamic, marked by new plant construction and capacity expansion at older plants. The industry has also seen plant closures, changes in ownership of existing operations, the consolidation of the Canadian nepheline syenite industry, and the increase of imported feldspar products. The industry has been affected by contractions in its major end-use markets brought about by economic cycles, product substitution, and environmental effects, such as recycling, land-use controversy, and air and water pollution. Despite problems, the industry remains mature and highly competitive. GEOLOGY Mineralogy The common feldspar group of minerals form a single crystalline phase or solid solution series of minerals. Fig. 1 is a ternary phase diagram that shows the feldspar mineralogy-KAlSi,O8, NaAlSi3O8, and CaAl2Si2O8. The end-member compositions are also referred to as potassium, sodium, and calcium feldspar. The feldspars whose chemistry ranges between the potassium and sodium end-members are known as alkali feldspars, while those between the sodium and calcium end-members are plagioclase feldspars. These feldspar groups can be further subdivided based on structural and compositional features within the alkali or plagioclase feldspar series. The distinction between and the proportion of members of the two feldspar groups are important to the classification of igneous rocks (Deer et al., 1966). Perthites are the exsolution product of an initially homogeneous potassium-sodium feldspar solid solution which forms (in an environment of decreasing temperature) a heterogeneous intergrowth of sodium-rich feldspar lamellae in a host crystal of potassium feldspar. Antiperthites are exsolution products in which the host mineral is sodium-rich plagioclase feldspar and the intergrowths are potassium-rich feldspar.

Jan 1, 1994

By Felicia F. Peng

In operation of column flotation of fine coal, the smaller bubbles are required to effectively recovery of fine hydrophobic particles. However, smaller size bubbles alone does not ensure an efficient flotation for fine particles. The sufficient available bubble surface area per unit column are essential for effective column flotation. The experiments are conducted in a lab-scale column using two different bubble size distributions and three different particle size distributions for flotation of Pittsburgh No.8 seam coal. The interaction between particle size, aeration rate, feed rate and wash water addition are examined in this investigation to establish the optimal operation conditions for flotation of fine coal. Despite of wide range of operation conditions used in this study, it is found that the experimental data fall in a single characteristic recovery-ash curve for a given bubble size distribution and particle size distribution. The major parameters affect the flotation performance points along -the characteristic recovery-ash curves are aeration rate/frother dosage, feed rate and wash water rate-.

Jan 1, 1994