Search Documents

By M. H. Foroughi

This paper discusses the effects of seam inclination and lateral stresses on the stress distribution in pillars in inclined coal seams. The average pillar stress is a function of the overburden weight, the mine depth, the effective extraction ratio and the angle of seam inclination. Normal and shear stresses in the pillar are computed by numerical modeling. In medium dipping seams, leaving a pillar with its axis normal to the stratification causes a shearing stress concentration in the top and bottom corners of the pillar. This results in the pillar possibly becoming less stable in comparison to pillars in horizontal coal seams. Therefore, to reduce the stresses, it may be necessary to leave the pillar at an angle of b deviated from the normal axis to stratification. A mathematically approximate formula for determining b is proposed, and the results are confirmed by numerical modeling.

Jan 1, 1998

By R. L. Wolfrom, R. Hogg, S. Chander

A gravimetric method for measuring rates of capillary rise in powders was explored. Methods to improve reproducibility and consistency of the results were investigated. In particular, the effects of particle size and packing uniformity were addressed. Studies of the wetting behavior of both spherical glass beads and irregularly shaped synthetic graphite particles by various organic liquids were carried out. Standardized procedures for bed preparation will be described. The applicability of the Washburn equation for surface energy evaluation in such systems will be discussed. Key words: Wettability, Powders, Capillary rise, Surface chemistry

Jan 1, 2003

By R. G. Darmody

Chemical problems associated with surface mining, such as acid generating materials, are important and well documented. However, reclamation research has shown that poor soil physical condition is the most limiting factor to successful row crop production on reclaimed mined land. Critical to success are selection of the best available soil materials used in soil construction and a material handling method that minimizes soil compaction. Excellent corn and soybean yields have been achieved on low strength soils both in high weather stress years as well as low stress years. Total crop failures have occurred on high strength soils in years of weather stress. Some deep tillage practices have been successful in improving compacted soils, but it is preferable to avoid compaction when the soil materials are handled. Soil strength measurements with a cone penetrometer have proven to be a useful tool in evaluating rooting media and reclamation practices. Research has shown that surface mining can be a short term land use that may be followed by productive farmland, if reclamation is done correctly.

Jan 1, 2002

By Wen-Long Cai, A. Frederick Banfield

This paper investigates, through case studies on a porphyry copper and a coal deposit, the differences and relevances between an approximate production schedule approach, i.e., the best case and the worst case schedules and a practical production schedule approach. The comparisons were with regards to: 1) choosing an optimum ultimate pit size, 2) determining processing capacities, 3) selecting 'optimum' cutoff grades, and 4) blending. The comparison criteria was to maximize the project net present value. Conclusions were drawn based on the study results.

Jan 1, 1996

By Robert C. Bates

Published information on costs of radon-daughter control in uranium mines was analyzed to develop estimates of the cost per ton for any level of radiation exposure control. All data were converted to 1967 cost of living index to provide a common analysis base. Results of the analysis show that the cost per ton increases exponentially as the radiation level is lowered. A linear relationship with the cost of living index is assumed, and equations and graphs are provided to estimate control cost per ton for any exposure control level and cost of living index.

Jan 1, 1981

By Y. Lin

The objectives of this investigation were to study the zeta potential characteristics of a Powder River Basin coal in water and to study the effects of zeta potential on the agglomeration of coal particles. The electrokinetic measurements show that the zeta potential of the coal is dependent on pH, temperature, coal concentration and contact time with water. The effects of various additives for changing the zeta potential of the coal were also evaluated. It was found that the strength of the coal agglomerates is increased when the zeta potential diminishes. Neutralizing the zeta potential enhances agglomeration. Therefore, it is important to control the zeta potential of coal to achieve optimum performance in coal-particle agglomeration.

Jan 1, 1997

By David Jenkins

Grefco Inc. operates two diatomite mines in the western Santa Ynez Mountains. The larger of the two mines, the Palos Colorados Mine, is located approximately seven miles southeast of Lompoc. The Miguelito Mine is located about two miles south of Lompoc on the west side of the Miguelito Canyon. Diatomite from the Palos Colorados and Miguelito mines is trucked to the Grefco plant at Lompoc for processing (Figure 1). HISTORY Grefco, Inc. evolved from the originating Dicalite Company which in 1929 began operations at the Walteria plant in the Palos Verdes Hills south of Los Angeles. In 1942 Dicalite leased the Palos Colorados mine at Lompoc. In 1944 the Dicalite Company was purchased by Great Lakes Carbon Corporation.

Jan 1, 1995

By R. R. Beebe

When an economic mineral deposit is first discovered, it is almost immediately defined in terms of tonnage and grade. As exploration and assessment continue, the initial definition is ordinarily qualified by such terms as "proven," "probable" and so on. Even at this stage, the fundamental philosophies of the discoverers may manifest themselves in conservative or optimistic views of the deposit's potential. It is unusual, however, for the philosophies to be expressed in terms of metallurgical performance criteria at such an early stage unless the ore is very unusual in its chemistry or mineralogy. Even before drilling is completed, the first mining plans appear, with or without the benefit of metallurgical test data. This is the point at which management philosophies can have some of their greatest impacts. In ideal cases, where large, uniform ore bodies can be developed and mined according to assay cutoffs, the conventional philosophy of maximizing tonnage while minimizing cost can be followed without much metallurgical difficulty. Unfortunately, such cases are rather uncommon. Even large, low-grade

Jan 1, 1991

By H. Sevim

This paper summarizes the research effort in simulating the operation of "Underground Coarse-Coal Hydrotransport Systems" (UCCHS). The equipment of the system to be simulated is already optimally selected by using an analytical optimization model. The purpose of the simulation model is to test the performance of the system and to obtain the distributions of operating parameters such as water and power consumption and amount of slurry delivered to the preparation plant. Knowledge of the distributions of these parameters is essential for the efficient operation of the system.

Jan 1, 1987

By D. Harney

Accurate measurement, tracking, and planning are vital for efficient utilization of energy in any mining operation, the major focus of this paper. This can be done with a number of assessments: 1) accurately measure KWH usage and track peak demand periods first; 2) identify the electrical equipment that affects your usage and the conditions that require it to be running; 3) remotely monitor and control as much equipment as possible, especially larger pieces of equipment; 4) with your utility determine that you are on the most suitable rate for your usage profile, then understand how your utility company calculates your electrical bill; 5) recognize how production affects energy usage and utility costs; 6) keep historical records of everything you monitor; 7) make information, live and historical, available to everyone; and finally, with the knowledge of your equipment and energy needs, automate controls that you have identified to optimize your energy usage and time of usage.

Jan 1, 2007

By Ernest K. Yanful, Paul H. Simms

The lysimeter is a useful tool for evaluating the performance of mine waste covers or liners. A major problem with its application is the possibility for preferential flow into or away from the lysimeter, if the lysimeter soil is finer or coarser than the barrier soil or sub-base soil. Analysis of a field lysimeter using a two-dimensional unsaturated-saturated liquid flow model suggested that preferential flow would occur and little or no water would be collected; however, in the field, the lysimeters collected significant amounts of water. A similar discrepancy was found between the observed and predicted water balance of a simple laboratory test simulating the lysimeter design. Vapour flow and partial flow, two phenomena not generally simulated in conventional flow models, are possible explanations for the difference between field and laboratory observations.

Jan 1, 2000

By Jan Wolski, Jack Barry

Ventilation ductlines with a single fan or with a series of fans are analyzed. The duct friction loss factors are discussed. Numerical solutions, presented in the paper, applies to any fan number and locations along a duct line. The findings are compared with formulas available in the technical literature. Values of the air leakage factors are presented in the SI, technical metric, and US unit systems. A method is shown of how to determine the leak- age factor for a given ductline. Optimum solutions for the sample duct lines with two and five fans in series are discussed and presented in a graphical form. Performance of fans in series is discussed in conjunction with both friction pressure loss and leak- age.

Jan 1, 1997

By Eric Forssberg, Benny Andreasson

The paper describes experiments to stabilize mineral processing waste materials for use in construction. Fine mineral processing wastes from various mines have been mixed with binders and compacted. As binders blast furnace slag and other materials have been used. Experiments have been made in laboratory scale and in large scale. The results have been evaluated by means of determinations of compression strength and the modulus of elasticity. The paper also describes some experiments in laboratory and large scale to use stabilized mineral processing wastes for back filling in cut and fill mining.

Jan 1, 1992

By Dean J. Soderstrom

Soil and sands were contaminated with depleted uranium from weapons testing. This resulted in the formation of a complex mixture of uranium compounds. Characterization studies of the soil indicated the uranium was present as uranium metal, uranium oxides, silicon-bearing metallic uranium, and uranium silicates. A process was developed to selectively remove dense uranium compounds using gravity separation and a chemical extraction system to remove uranium which was not available for separation by gravity methods. Results from characterization studies and pilot scale testing are presented for background information. The primary purpose of this presentation is the report of the results achieved in the field application of the processes.

Jan 1, 1995

By J. Hanna, H. R. Gonzalez

Four Ca-bentonitic clays from Alabama were evaluated for use in diammonium phosphate (DAP) or urea ammonium nitrate (UAN) fertilizer suspensions. The viscosity and gel strength of suspensions prepared with different proportions of a Western bentonite clay and sodium-exchanged Alabama clays were measured as a function of clay content and dispersant concentration. The results obtained suggested that three of the Alabama Ca-bentonites would replace about 40% of the more expensive Western bentonite in UAN and DAP fertilizer suspensions. The performance of the Nu-modified clays, prepared according to the Tennessee Valley Authority soda ash method, was as good or even better than those observed for the Mg-, NaIMg- or K-modified clays. The TVA clay modification procedure appears to be reliable and cost effective.

Jan 1, 1991

By J. Paraszczak

Water-powered jackleg rock drills, introduced recently in South African mines, are reported to be more efficient, faster and more comfortable to operate than conventional pneumatic drills. Comparative testing of these drill types was performed in Quebec. Based on the test results and on time studies performed in the mines, water-powered drilling was reviewed. The review considered the drilling rates achieved, the infrastructure needed, side effects and health and safety considerations. This study shows that the application of water-powered drills may, under specific conditions, help increase the footage drilled and may improve the working environment. Examples of such applications are presented in the conclusions.

Jan 1, 1997

By J. Mastoris

The determination of the surface area that may be impacted by underground mining is an important consideration in subsidence engineering. A number of parameters have been utilized to identify this influence area, most notably the angles of draw and break. This paper discusses the implications of selecting an appropriate "damage angle" for defining a potential damage area due to mining, within which surface structures may be impacted. Furthermore, the influence of both mining and geological factors (i.e., mining width, depth and overburden lithology) on this angle is examined using the Surface Deformation Prediction System (SDPS) software. Finally, recommendations are given for applying these concepts in subsidence control.

Jan 1, 1995

By John K. Kellis

With the cost competitive nature of material mining, the ability to actively monitor the condition of the conveyor belt systems without personnel dedicated to that task is very desirable. This paper discusses the development of a conveyor belt condition monitoring system, which actively monitors the conveyor belt, without the need to install special antennas. A belt width map can be generated, as well as detection of three types of physical damages: (a) failure of mechanical fasteners, (b) reduction in belting strength due to reductions in competent belt width, and (c) longitudinal belt rips.

Jan 1, 2000

By J. E. Gebhardt, L. Piga, G. Schena

The possibility of beneficiating a low-grade alunite ore from the Tuscany region of Italy was examined. Flocculation and flotation techniques were investigated to separate alunite and kaolinite from the ore, which also contained feldspar and quartz. Flotation was performed at pH 6.5 with oleic acid as collector and sodium silicate as dispersant. A concentrate containing 12% alunite with a recovery of about 65% and a concentrate containing 28% alunite with a recovery of 84% were achieved from the -38-µm feed samples containing 5.0% and 12.9% alunite, respectively. Poor recovery of alunite was achieved by flocculation methods.

Jan 1, 1999

By J. B. Hiskey, V. P. Atluri

Resin-in-leach (RIL) cyanidation experiments were performed on a refractory carbonaceous gold ore. The objective of this investigation was to determine if strong-base ion exchange resins could adsorb the soluble aurocyanide complex in preference to natural "preg robbing" organic constituents. Direct cyanidation of the carbonaceous gold ore used in this study resulted in less than 2% gold extraction in 24 hr. RIL cyanidation resulted in about 70% gold recovery onto the resin. Kinetic experiments indicated that 50% of the gold is extracted after 1 hr of leaching. Resin breakage was investigated for as-received and preattrited resins. Similar results were obtained with three different strong base resins.

Jan 1, 1990