Search Documents

By Rudolf E. Greuer

It is undisputed that an interaction between mine fires and mine ventilation systems exists. The ventilation carries the poisonous and sometimes explosive combustion products, which constitute the greatest danger of mine fires, through the mine and it provides the oxygen on which the intensity of the fire depends. The fire, on the other hand, can produce considerable ventilation disturbances which make it difficult to predict the path along which the combustion products travel. The opinions, how serious a threat such fire generated ventilation disturbances are, vary. Where shallow deposits are mined and brisk ventilation currents are used, it is frequently felt that these disturbances are of no serious concern. Where mine workings extend over larger elevation differences and where such disturbances have been encountered and been the cause of some larger disasters, their assessment is an integral part of all fire emergency plans. The author felt that the potential of digital computers for the design of ventilation emergency plans, contrary to their acceptance for conventional ventilation planning for more than two decades, is not yet fully utilized. He designed a program for the simulation of ventilation systems under emergency conditions in particular fires. This was part of work completed for a contract with the U.S. Bureau of Mines ( Open File Report OFR 115(1)-78)

Jan 1, 1980

By G. C. Presley

Estimated domestic production of pumice and pumicite in 2004 increased about 23 percent since 2003, according to the U. S. Geological Survey (USGS). The USGS estimate of domestic production of 687 kt(757,000 st) for 2003 turned out to be 870 kt (959,000 st)of actual production. The USGS estimated the value of pumice and pumicite sold or used in the United States to be $26 million in 2004, up $4 million from the value in 2003. There was an estimated decrease in the mine, or mill, average price to $24.14/t ($21.90/st) in 2004 from $25.19/t ($22.85/st) in2003.

Jan 1, 2005

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By D. W. Rich

An environmental management system (EMS) is a key part of a company?s environmental stewardship. Procedures and practices to continually improve environmental performance can provide great benefits in operating the company. Managing site environmental quality data is a key component of this. An environmental data management system (EDMS) is an important element of the EMS for mining and other projects, providing project staff with the information that they need to make decisions that can have a significant impact on public health. Improvements in computers, data communications, and transfer formats have made it much easier to implement an integrated EDMS program for gathering, managing, selecting, and displaying data from the field and the lab. Software now lets users define sampling plans, create files for field data entry, and print Chains of Custody. Laptop and handheld computers facilitate field data entry and may provide automated communication back to the office. Most labs can now create usable electronic data deliverables. QC checks and limit comparisons can be largely automated. The result is organized data that can be efficiently used for reporting, graphing, and mapping, to better understand project issues.

Jan 1, 2009

By W. L. Garrison

Improvements continue to be made in rapid excavation and tunneling technology. There are several ways to examine the impacts of such improvements. The most common procedure is to monitor current developments and to evaluate prospects for expansion of present types of uses. Other approaches are called for, however, if the technology might be used in ways not now imagined, if the search is for information for managers of technology development, and if the issue is that of the wise use of the technology by society. The first section of the paper will pose these matters as questions. These questions will be examined from the point of view of the processes of technology development and utilization, and then further examined against the backdrop of processes at work within the urban area. Such an examination will provide insight into the way technology developments should proceed. The final section will present some comments that may be useful to those guiding the development of the technology and to those who might provide leadership for its wise utilization. THE QUESTIONS Three questions are posed: 1. Are there uses for the technology beyond further penetrations of its present markets? 2. Can information be supplied to managers of technology development so that they may improve the assignment of priorities among development choices? 3. How can society make wiser use of the technology?

Jan 1, 1974

Newmont Gold's methods for deposit modeling vary, depending on geology, mining and processing methods, economic feasibility and availability of historical information. It is argued that successful modeling requires understanding these factors, knowing the strengths and weaknesses of the various modeling techniques and being flexible in selecting the appropriate methods. Newmont is one of the world's largest gold mining companies, with operations in the United States, Peru, Mexico, Indonesia and Uzbekistan. And it is active in exploration worldwide. At the end of 1996, Newmont declared a total reserve of 1.15 equity kt (37.1 million equity oz) of gold and 2.17 equity Mt (2.39 million st) of copper. The gold deposits managed by Newmont totaled 752 Mt (829 million st) of ore containing 1.28 kt (41.3 million oz) of gold averaging 1.71 g/t (0.05 oz/st). In addition, Newmont is developing a porphyry copper-gold deposit that totals 9.1 Gt (1 billion st) of ore containing 380 t (12.1 million oz) of gold and 4.82 Mt (5.32 million st) of copper. (In May 1997, Newmont Gold Co. merged with Santa Fe Pacific Gold Corp., thus increasing Newmont's reserves to 1.72 kt or 55.2 million oz of gold and 2.17 Mt or 2.39 million st of copper.)

Jan 1, 1998

By Mike Tracy

This section of the Handbook deals with general principles to be evaluated in the development of a mining operation. It addresses the major issues that must be examined to fully evaluate a mining venture. Of course, one of the main topics to be evaluated is mine planning, which is covered in more detail in other sections (13, 17) of the Handbook and should be referenced in mine development projects. The topics to be discussed in this introduction include equipment and supplies, infrastructure, utilities, and project management. In any of the aspects mentioned, the current existing conditions at or near the mine site must be evaluated. This will include assessment of current use of utilities, infrastructure, housing, equipment suppliers, etc., as well as anticipated growth, both in the supply aspect of these systems as well as projected usage on these systems. After full assessment of both these aspects, an evaluation must be made as to the requirements the project will place on these items. Assessment must be made as to any up-grades required to bring the project on line, what impact the project will have on existing or expanded systems, and anticipated future growth impacts on support systems not only of the project but of other surrounding industry and urban devel-opment

Jan 1, 2008

By Antti Porvali, Vivek Agarwal, Mari Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2·H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can then be further converted with NaOH solution to form REE hydroxides. However, present literature has paid little attention to how to minimize the consumption of reagents in this recovery process. In the current study, a process model was built using HSC Sim software, and metamodeling of the simulated flowsheet was conducted with the design of experiments (DOE), after which the basic functionality of the flowsheet was verified by experimental work, starting from sulfuric acid leaching of spent batteries. As the process is based on chemical circulation internally in the process, the objective was to investigate the accumulation of the elements in solution, specifically Na+ , K+ , SO4 2− ions and impurities liberated in the NaOH conversion step. It was found out that metamodeling could be utilized in obtaining first estimate of the process behavior, prior to any experiments. Flowsheet functionality with circulated solution was confirmed, obtaining at best 96.9% La recovery.

By Antti Porvali, Vivek Agarwal, Mari Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2·H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can then be further converted with NaOH solution to form REE hydroxides. However, present literature has paid little attention to how to minimize the consumption of reagents in this recovery process. In the current study, a process model was built using HSC Sim software, and metamodeling of the simulated flowsheet was conducted with the design of experiments (DOE), after which the basic functionality of the flowsheet was verified by experimental work, starting from sulfuric acid leaching of spent batteries. As the process is based on chemical circulation internally in the process, the objective was to investigate the accumulation of the elements in solution, specifically Na+ , K+ , SO4 2− ions and impurities liberated in the NaOH conversion step. It was found out that metamodeling could be utilized in obtaining first estimate of the process behavior, prior to any experiments. Flowsheet functionality with circulated solution was confirmed, obtaining at best 96.9% La recovery.

By Edward DeLilla

For the past 30 years, surface mines have moved toward more highly mechanized, automatic systems that continuously mine overburden and ore to increase productivity, lower operating costs and minimize manpower needs. To achieve these goals, mine operators must be involved in every step of the machine procurement process. Several factors are involved in making the machines operate economically and efficiently: -Prudent engineering. -Proper planning. -Realistic feasibility studies. -Effective specification. -Thorough training of the mine personnel.

Jan 1, 1994

By Galyn Rippentropp, Finn Erik Overlie

INTRODUCTION The wet shotcreting system utilizing steelfiber microsilica shotcrete with remote controlled equipment (The Robocon System) was developed in Norway 7-8 years ago. Norway was the natural origin for this system due to several factors. Almost 30% of all underground hydro-power stations in the world are located here. These projects created a need for high productivity shotcreting rigs for the rock support work in the caverns and in the connecting tunnels. During the period of 1976-1980, more than 1000 miles of tunnels were completed in Norway. Secondly, the utilization of microsilica in concrete was also developed in Norway due to a concentration of the world's ferroalloy p ants there. Robocon has presently placed approximately 110,000 m (150,000 cu. yds.) of this superior shotcrete, and has consequently an extensive experience in the shotcreting method. During a relatively short period of time (1975-1980), Robocon had a change from hand-operated, dry-process shotcrete to remote-controlled, wet-process shotcreting, because of improved productivity, reduced rebound, safer and cleaner working conditions. The introduction of microsilica and water-reducing admixture made it possible to produce wet-process shotcrete of high strength.

Jan 1, 1987

By U. B. Kodukula

Attempts are made to evaluate the feasibility of using a water-injection cyclone for the concentration of iron ore fines. The separation characteristics of clay fines, containing large amounts of alumina and silica, from the iron values are discussed. The effects of critical variables, such as injection water rate, truncated cone diameter, spigot opening and vortex finder diameter, on the performance of a water-injection cyclone in terms of iron, alumina and silica grades; iron recoveries; and alumina and silica rejections are discussed. A set of 16 full-factorial experiments (24) was carried out to gain an understanding of the individual and interaction effects of the variables. The results indicate that classifying iron ore fines containing 63.0% iron, 2.5% alumina and 3.5% silica through a water-injection cyclone can produce concentrates with iron grades greater than 66.0% and alumina and silica contents less than 1.5% and 2.0%, respectively, at different study conditions. The achievable iron recovery values are greater than 88%, and alumina and silica rejections are more than 80% and 50%, respectively, within the specific study conditions. While the truncated cone diameter, injection water rate and spigot diameter influences the alumina rejection to a considerable extent, it is mostly influenced by the vortex finder diameter. The iron recovery and silica rejection values are mostly influenced by spigot diameter and truncated cone diameter. The effect of injection water on the concentration characteristics depend on the prevalent truncated cone diameter and spigot diameter conditions.

Jan 1, 2008

Editor's note: Biographical information about Ihor Kunasz, president, Newmont Uzbekistan, can be found in the February 1998 issue of ME, page 94 and in the May 1996 issue, page 92. Your personal assessment of the minerals business. Gosh! When I think about what has happened to the minerals industry over the past 27 years that I have been a member of SME! There have been fundamental structural changes in the industry. And I think that SME has been quite successful in coping with these changes as well. There has been a reorientation in how the minerals industry does business. It used to be called rationalization. Today we call it reengineering. In addition, the minerals industry has become more complex and more global. Shareholders have become more vocal and demanding in the management of the business, asking for protection of their shareholders' value. In the 1980s, a fundamental change was precipitated by a merger and acquisition fever in all industries, including the minerals industry. Raiders such as T. Boone Pickens put enormous demands on companies that, in turn, had to spend substantial management time to fend off the raiders. This resulted in a major restructuring of the mining houses. Today, for example, Anaconda, Kennecott and Amax are only historical names.

Jan 1, 1998

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Thomas Marcher

Stanford Linear Accelerator Center (SLAC) is located in Menlo Park, CA. In order to allow for enhanced experiments, the current facilities required expansion. Tunnels were excavated through very weak sedimentary rock interspersed with uncemented zones (Ladera Sandstone) employing the principles of the NATM. The overburden var-ied from 10 to 80 feet. The paper addresses the characterization of Ladera Sandstone that can exhibit the properties of dense sand and weak rock. The paper focuses on the challenges that were encountered during the NATM initial support design and the construction phase including the geotechnical instrumentation, monitoring and design verification process in particular the excavation of the junction between access tunnel and the FEH cavern (49 ft wide by 32 ft high).

By Heiner J. Sander

Stanford University operates the National Research Facility which is located at the Stanford Linear Accelerator Center (SLAC) in Menlo Park, California. In order to improve and allow for enhanced experiments, the current facilities required expansion. A1500 foot long tunnel (20 ft wide by 21 ft high) and a 220 foot long underground cavern (49 ft wide by 32 ft high) were excavated through the Ladera Sandstone formation which is an intermediate geo-material with week rock properties. The overburden between surface and crown of the structures varies from 10 to 80 feet. The underground structures were excavated according to the principles of the NATM (New Austrian Tunnel Method). This paper addresses the challenges that were encountered during the construction phase of the project and how construction issues were resolved mutually by the owner, engineer and contractor. The implementation of geotechnical instrumentation, recorded data and interpretations, soil conditions and behavior encountered during construction are also presented.

Jan 1, 2008

By P. Campbell, E. M. Gardy, L. Hachkowski

Introduction The efficient process control of a uranium mill and its associated mining operation requires a nearly continuous knowledge of the uranium concentration in the ore. Generally, the approach is to use laboratory assays of grab samples from the mill feed belt. In some cases, elaborate and expensive systems have been used to ensure random sampling, but even with these systems, mass-balance discrepancies still exist. There is a requirement for an on-line instrument that can give a prompt, accurate analysis of a large portion of the feed stock. The authors have recently evaluated a laboratory system that achieves these goals using neutron activation and delayed neutron counting. The development of the on-line uranium ore analyzer is a consequence of previous work done at the Whiteshell Nuclear Research Establishment (WNRE) (Campbell et al., 1978 and 1981), and is based on the emission of delayed neutrons after the neutron irradiation of fissionable materials. The mechanism of delayed neutron emission has been described (Keepin, 1965), but briefly is as follows. The fission fragments resulting from irradiation are in an excited state. Certain of these delayed fission products, precursors, decay to a more stable state by the emission of a delayed neutron. The delayed neutrons can be divided into six groups with effective half-lives ranging from 0.2-55 sec. It is important to note that more than 50% of the delayed neutrons are emitted within the first 6 sec after irradiation; this has an influence on the design of the analysis instrument. Measurement Cycle The measurement cycle involves a neutron irradiation, a delay time, and a counting period. The laboratory demonstration model of the ore analyzer comprises a californium-252 neutron source, a source chamber, a pneumatic transfer facility, and a neutron irradiation and counting module (Fig. 1). The ore sample is placed in the irradiation chamber. The neutron source is transferred to the center of the chamber for a 5-sec irradiation while the helium-3 thermal neutron detectors are switched off. As the source returns to the storage chamber, the detectors are switched on and the delayed neutrons counted. The total assay cycle is 16 sec. The current instrument design calls for the ore to be cut from the main belt every 16 sec by a mechanical arm and dropped into the analyzer directly, or via another belt. The cycle starts when there is a sufficient mass of ore in the irradiation chamber to depress a switch and stops when the delayed neutron count is finished. The ore is then dropped through the bottom of the analyzer chamber and returned to the main belt. The counts from each cycle are accumulated and the data reduced to give the desired information. Key for Fig. 1 A-Helium-3 neutron detector B-Wax moderator for neutrons C-Irradiation chamber D-Funnel for receiving ore E-Gate F-Transducers G-Biological shield for neutron source H-Transfer tube for neutron source I-Neutron source J- Microprocessor K-Accumulator for hydraulics L-Control panel M-Electro-hydraulic servo valve to control movement of the source N-Electro-hydraulic proportional valve to control movement of the gate O-Hydraulic power unit Irradiation and Counting Equipment Irradiation of the ore is achieved using a 1 X 10 7 neutron*s-1 californium-252 neutron source. The source is contained in an iron capsule and pneumatically transferred between the irradiation/counting and storage chambers. The irradiation/counting chamber possesses 12, 600-mm (24-in.) long helium-3 thermal neutron detectors embedded in an annulus of wax (Fig. 1). Two sets of six detectors are each interfaced to a preamplifier, amplifier and single-channel pulseheight analyzer system, and the two systems are connected to a scaler. A special timing unit controls the transfer of the source and the on and off switching of the detector assembly, in sequence with the movement of the source. Results and Discussion In the experimental demonstration, using the 107 neutron.s-1 source, a 10% uranium ore was measured to ± 10% (2o total error) in 10 cycles and ±6% (2o) in 100 cycles. Since a larger source was not available, it can be statistically predicted that a 109 neutron-s-1 source could be used to measure a 0.1% ore to ± 10% (20) in 10 cycles. The uranium can occur as discrete nonhomogeneous particles in the ore, and the error caused by such a distribution of particles is ± 4% (2o), as determined by

Jan 1, 1984

By David L. Veith

As the basis for the State of Minnesota's Regional Copper-Nickel Study environmental evaluation, hypothetical mine models were developed ranging in ore capacity from 5.35 to 20.00 x 106 mtpy. Open pit and underground mining operations were defined utilizing conventional methods of ore extraction. Processing of the copper-nickel sulfide material involved conventional bulk flotation of the valuable minerals, with maximum water recycle And tailing disposal. Flash smelting and electrolytic refining of the concentrate resulted in 0.10 x 106 mtpy copper plus nickel metal, plus associated cobalt and precious metals. Variations in model parameters allowed environmental trade-offs to be identified.

Jan 1, 1980

By Steven K. Duke, Jay Arabshahi

An economic, real-time probe drill monitoring system was developed for Metropolitan Water District’s Arrowhead Tunnels project to quantitatively evaluate ground conditions ahead of a TBM. This system digitally records hydraulic feed, rotation, and percussion pressures and calculates drill advance rates during drilling. These data are computer synthesized to develop a digital representation of the ground ahead, and the resulting “picture” of the ground is distributed to the project team to assist with tunnel construction decisions (i.e., targeting grout holes, optimizing mine-cycle lengths, and avoiding becoming stuck). The analysis and interpretation procedure has now been calibrated and refined using over 5,000 m (3 miles) of geologic face mapping data.

Jan 1, 2007

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011