Search Documents

By Eduardo Poltronieri Trés, Anderson Denadai Thomazini, Rodrigo Boyer Fernandes, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Maycon Athayde, Rossano Augusto Pilon Nunes

The fundamental importance of comminution by high-pressure grinding roll (HPGR) technology to efficiently increase the particle surface area lies in lower energy and water consumptions for iron ore pellet feed production. This study compared the ball wet milling process with the innovative HPGR processing technology for hematite-goethite ores. Green-pellet balling and induration processes were simulated on the bench and pilot scales.

By Bryant Fitch

This paper will review thickening theory, from the ( ) of the practicing engineer, with particular emphasis on ( ) uncertainty or disagreement. It will attempt to outline broadly what we know and what we don't know. This should serve two purpose First, it will warn the process engineer where he might get into trouble. At least it will alert him to the risk involved in uncritically accepting any of the recommended design procedures. Second, it will identify for researchers some areas in which further work might be fruitful. Not too many years ago there would have been little to write on such a subject. We had been designing thickeners for decades, using the classic Coe and Clevenger procedure. As far as we were generally aware, they all turned out to be about the right size. And so if there was anything we didn't know, It certainly wasn't hurting us much. Today we know better. While it is true that in most cases units designed by the Coe and Clevenger procedure (1) will perform satisfactorily, we now know of cases in which they don't. And during the past few years there have been many developments and advances in basic thickening theory. So there is now a lot more room for disagreement, and a whole lot more to be uncertain about. What is "thickening" "Thickening" means different things to different people. For this paper we define it to mean sedimentation behavior characterized by line settling. Solids subside with a clear line of demarcation between settling solids and supernatant. Although the supernatant will usually be clear, in some cases it may be turbid. Line settling must entail that all particles just below the pulp-supernatant interface have the same subsidence rate, so that

Jan 1, 1971

By James L. McGregor

St. Joseph Lead Company has been paying incentive bonuses for well over 40 years. In 1958 almost half of St. Joe's 1,860 employees in Southeast Missouri received some form of incentive bonus in addition to their guaranteed wages. There are very few payroll jobs in St. Joe s Southeast Missouri organization that lend themselves to a reasonably good measurement of production or quality, or both, where an incentive bonus is not paid. The term "Incentive Bonus" is used to differentiate betwen bonuses that are based on quantity or quality of work, and those that are merely additional pay of a standard amount per hour or day because of an employee being temporarily assigned to some unusual task, An employee temporarily assigned to a job where the working conditions make the job performance unusually difficult or where a special skill is used is often given a bonus of some standard amount per hour or shift in addition to his usual rate. This is merely a convenient way of paying something extra without disturbing the normal rate structure. Actually, it is differential pay similar to that almost universally paid for evening and night shift work. Bonuses of that type are not being considered in this paper. The basic reason or theory for paying incentive bonuses 9s to get improved production at lower cost, Unfortunately, it is often difficult, if not impossible, to find a yardstick by which it can be definitely proved that a particular bonus plan is accomplishing its purpose, It becomes, then, a matter of judgment on the part of management personnel as to the value of the bonus plan. The fact that St. Joe Lead Company has continued to pay bonuses for over 40 yews and has increased the number of bonus schedules used attests to a definite belief that they are beneficial to the company's successful operations.

Jan 1, 1960

By James Corcoran, Richard McLane, Matt Neuner, Joseph DeMello, Hugh Davies

The Los Angeles County Metropolitan Transportation Authority (LA Metro) Purple Line Extension Section 1 (PLE1) is a $3.12 billion USD design-build, underground heavy rail project, connecting an existing station at Wilshire Blvd. and Western Ave. and extending 3.92 miles under Wilshire Blvd, terminating approximately 550 feet west of Wilshire and La Cienega Blvds. The project alignment runs immediately adjacent to the La Brea Tar Pits, world renowned for Pleistocene fossils and continuous seepage of asphaltum (locally known as tar) and gas in an urban setting. This paper presents a successful case history of the planning, design, and construction efforts to safely construct the bored tunnels through Reach 3 of the alignment (between Wilshire/Fairfax Station, and Wilshire/La Cienega Station), in a designated Methane Zone in the City of Los Angeles. Historical context on decades of challenges and studies is summarized. Further, this paper outlines the pro-active partnership between the Owner: LA Metro, the Design Builder: Skanska-Traylor-Shea Joint Venture, and geotechnical design services provided by Golder Associates to safely manage pressurized face tunneling through a confined gas zone near the La Brea Tar Pits. Specifically, a program of in-situ oxidation and soil gas extraction was designed to test and analyze risks associated with pressurized face TBM tunneling through the complex subsurface geological conditions, then implemented during construction. In advance of tunneling, a network of wells was used to draw air into the gas zone to oxidize the 6,500 ppm hydrogen sulfide gas, as well as determine methane recharge rate. During TBM tunneling, the wells were converted to a gas extraction system to evacuate, filter (H2S) and burn (CH4) the gas as the Tunnel Boring Machine passed, providing a preferential pathway for the gas to migrate toward extraction wells, and preventing the migration to adjacent buildings. The team extracted and treated 3,857,000 cubic feet of mostly methane gas over 40 days as the TBMs passed through the zone. Gas behavior, pressures, and concentrations were monitored not only from the extraction system, but also in basements and utility vaults along this section of the alignment.

Jun 13, 2023

By B. Samanta

This paper highlights the use of an innovative mine production scheduling scheme for grade-control planning tasks that take into consideration grade-model uncertainty. The scheduling exercise has been carried out with the help of a multiobjective genetic algorithm (MOGa) for the production scheduling operations. The underlying motive behind the use of MOGa has been the generation of a set of pareto optimal solutions to meet the goals of the target-grade specifications for the considered multiple grade attributes. Several new concepts related to MOGa formulation, in particular the mutation operation and the convergence criteria of this algorithm, are proposed in this paper. The modeling of grade uncertainty into the scheduling outputs has also been incorporated through a set of conditional simulated grade maps. The proposed scheme of production scheduling operations has been applied for the grade-control planning operations in an iron ore mine to meet the targeted grade specifications of iron, silica and alumina, and a risk analysis has been performed to this end.

Jan 1, 2013

The mineral sands industry is oriented primarily toward the supply of titanium (Ti) raw materials (titanium feedstocks) for the production of titanium dioxide (TiO2) pigment and titanium metal. Titanium minerals ilmenite, rutile and leucoxene, and titanium slag and synthetic rutile are all used principally as feedstocks for the production of white TiO2 pigment. It accounts for almost 90 percent of the world?s consumption of titanium minerals. The remainder is used for the production of titanium metal, fluxes for welding rods and as a metallurgical flux in iron and steel making. Titanium dioxide pigment is produced by two alternative process routes, the sulfate process or chloride process. The bulk of the world?s titanium dioxide is derived from the mineral ilmenite, which also contains iron oxide and other minor impurities. At some mining operations, the iron present in ilmenite is removed (ilmenite beneficiation) to produce a high TiO2 feedstock (slag or synthetic rutile) typically containing between 80 percent and 95 percent TiO2. Pigment producers then further process it to produce pigment.

Jan 1, 2011

By N. D. Jagger, I. M. Arbuthnot

Introduction Over the last five years, a large number of small- to medium-sized carbon-in-pulp treatment plants have been built in Australia, most designed to treat between 250,000 t/a and 1.5 Mt/a of ore. Because of the limited capital resources and tight cash-flow positions of these relatively small mining companies, the primary requirement was often to get a plant built and operating in a short period of time and at minimal capital cost. Therefore, since the inclusion of both pre-leach and tailings thickeners represents an obvious and significant capital cost, most of these plants were built without thickeners or even detailed, cost-benefit analyses on their inclusion. In some cases, the increasing use of High Rate Thickeners (HRTs) in the mineral processing industries has, however, resulted in a reassessment, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas where borefields are costly to install and water is limited. With the startup and operation of these installations, the resulting significant savings in cyanide consumption has been recognized, in many situations, as a primary justification for the installation of HRTs. Solution balances Degradation of cyanide occurs in the tailings water discharge to slime dams. The degree of degradation (cyanide loss) in the water recovered depends on a number of factors, but it is usually assumed to be about 90%. The most important mechanisms of CN loss are through HCN losses and oxidation by oxygen in the air, which also assists in the hydrolysis of CN. These mechanisms are supported by the large dam surface area and the long retention time of the tailings water in the dam. By thickening the CIP tailings at the plant and recovering as much tailings water as immediately possible, these losses are avoided. The retention time in an HRT is less than three hours, and the surface area is relatively small. Therefore, CN losses are negligible, which is not necessarily the case in conventionally-sized thickeners. Fig. I shows a block diagram of a 100-t/h gold plant without a thickener. In this example, 50% of the tailings water pumped to the tailings dam is recovered, and the CN concentration of the returned water is 10% of the tailings CN concentration of 150 ppm. Fig. 2 represents a plant with an HRT on tailings, thickening to 55% w/w solids. In this case, the thickened tailings are pumped to the dam, and 25% of the contained water is recovered. The recovered water and the mill make-up water are not sent directly to the mill; instead, they are added to the thickener feed and mixed with it prior to thickening. By doing this, the tailings are effectively washed, and the additional cyanide is recovered. Solution balances over these two circuits show cyanide recoveries of 5% and 65%, respectively. Thus, the thickener use increases cyanide recovery by 60%. Fig. 3 shows a two-stage HRT circuit in a countercurrent decantation (CCD) configuration. In this example, an additional 13% of cyanide is recovered through the use of the second-stage unit. This configuration can be justified when residual cyanide levels are high. Capital and operating costs - Case study 1 Illustrative cost figures are based on a CIP tailings thickener installed, in early 1988, as part of Dominion Mining's treatment plant at Paddy's Flat near Meekatharra. (All costs within this paper, unless stated otherwise, are in Australian dollars.) [Assumptions: Feed rate 150 t/h Ore moisture content 5% Leach density 40% solids Underflow density 55% solids Residual cyanide in tailings 150 g/m3 Flocculant dosage 15 g/t Consumable costs: Water $ 0.40/m3 Cyanide$ 2.00/kg Flocculant$ 4.50/kg Power$ 0.12/kWh Length of tailings pipeline2,500 m Capital costs of the major items involved in the thickener installation are given below: Thickener unit, 15-m diam $ 230,000 Water return pumps 12,000 Water recirculation pumps 28,000 Feed box 5,000 Flocculant make-up system 18,000 Flocculant storage tank and dosing pumps 11,000 Piping and valves 85,000 Electrics and instruments 47,000 Civil works 29,000 Installation 69,000 Total cost$ 534,000] Savings in capital costs that can be attributed to the

Jan 1, 1993

By Harold A. Taylor

The first use of graphite is lost in the mists of time. It was used by primitive man to make drawings on the walls of caves and by the Egyptians to decorate pottery. As early as 1400 AD graphite crucibles were being made in the Haffnerzell District of Bavaria. Through the Middle Ages graphite was confused with other minerals, especially galena and molybdenite. Two common names that are still being used for the mineral are plumbago, meaning lead-silver, and black lead. The latter name implied that graphite is either composed of lead or at least contains a large percentage of it. Gessner is credited with having recognized it as a separate mineral in 1565, but its composition was not determined until 1779, when Scheele demonstrated that graphite oxidized to carbon dioxide, thus proving its carbon constitution. In 1789, Werner named it graphite from the Greek word graphein, meaning to write. The United States has long relied on foreign countries for its graphite supplies. This reliance has been due more to the lack of suitable domestic graphites than to any particular preference for buying minerals overseas. Sri Lankan graphites were imported as early as 1820, and Madagascar graphites have been imported since the properties on that island were opened up about a hundred years later. Mexico has long supplied the United States with most of its requirements for amorphous graphite.

Jan 1, 1994

By Nick Barton

The ability to estimate that support is unnecessary for various dimensions of opening in certain rock mass environments is of particular relevance in the mining industry, where most excavations are not expected to remain open indefinitely. As Hoek1 observes: "the basic aim of any underground excavation design should be to utilize the rock itself as the principal structural material, creating as little disturbance as possible during the excavation process and adding as little as possible in the way of concrete or steel support". Approximately two hundred case records have been analysed for the purpose of determining the amount of permanent support normally used when a given span is excavated in known rock mass conditions Some thirty cases concerned unsupported openings. Excavations that can stand unsupported appear to have certain common characteristics as regards rock mass quality. However, the mechanical properties of the rock mass are not the only factors controlling the choice of design. The dimension of the opening (span or height) and the type of excavation are two important variables.

Jan 1, 1975

By Haydn H. Murray

Although alumina constitutes about ii percent of the earth's crust, it is expensive to separate and purify for the production of aluminum with the exception off the alumina in bauxite. The United states has a variety of non-bauxite resources that could substitute for bauxite, including high alumina clays, alunite, dawsonite in oil shale, anorthosite, and nepheline syenite. Each of these resources are discussed from the standpoint of geology, geography, processing, potential recovery, and environmental problems. Potential by-products include silica from clays, potash and sulfuric acid from alunite, soda ash from dawsonite, and soda ash and potash from anorthosite and nepheline syenite.

Jan 1, 1982

By A. J. S. Spearing, B. Forbes, T. Kostecki, A. Hyett

Improving upon the past understanding of the interaction between installed rock bolts, the immediate roof and sidewalls is vital for the implementation of sound support system design, as this has a direct impact on rock-related safety. This is the primary goal in rock-bolt-related research. The earliest research in this field concentrated on limited laboratory and in situ measurements accompanied by theoretical analyses, based on the Kirsch equations. This represented the initial insight into understanding relative ground movements and their impact on primary support. However, these studies were far from complete. More recently, major technological advances in computing power within the mining industry has changed the scope from theoretical analysis to computer simulation. Even with these advancements our understanding of rock bolts in situ and in the laboratory has not progressed, particularly concerning bending and shear. To measure the behavior of rock bolts, the widely accepted practice is to populate the bolts with an array of strain gauges. Historically, resistive foil strain gauges or long displacement sensors have been used. Additionally, all instrumented rock bolts have used only two diametrically opposed slots. Rock bolts instrumented with these methods have significant shortcomings, one of which is the inability to capture shear and bending. The shearing and bending of rock bolts are particularly common in tabular soft rock mining, such as coal mining. This paper discusses the use of three slotted rock bolts, cut diametrically 120º apart, and two new optical fiber technologies populated along the entire rock-bolt length.

Jan 1, 2015

By Choon K. Quan

Subsidence is a surface manifestation of the underground development and exploitation of minerals, and its impact on the environment is becoming of increased concern, particularly in the face of an accelerating demand for energy and minerals. In the United States, the state-of-the-art in subsidence prediction, control, and prevention and in subsidence-related damage abatement has not progressed to the level achieved in other countries. To bridge this gap, the Bureau of Mines, through its Mining Environmental Research program, is pursuing a comprehensive subsidence investigation, specifically designed to address major problems on the local, regional, and national level.

Jan 1, 1979

By S. K. Kawatra

In this paper three methods of on-stream analysis 1) Radiometric techniques, 2) X-ray tube techniques and 3) Neutron activation method are reviewed. Advantages and disadvantages of each method are discussed.

Jan 1, 1984

By M. R. Haibach, M. L. Shema, J. M. Silvis

"Since 2005, longwall coal mine operators in Pennsylvania (US) have been required to collect extensive hydrologic and biological data to document pre- and post-mining conditions of aquatic resources (streams and wetlands) overlying the subsidence control plan areas. Continued operation of the longwall mine is dependent upon empirical data demonstrating that the undermined aquatic resources have either been maintained or restored to an accepted range of pre-mining conditions. This study used quantitative hydrologic methods and comparative biological metrics to examine response of aquatic resources to longwall subsidence at the Bailey Mine located in Greene County, Pennsylvania. This study analyzed data from over 25 miles of streams and over 8 acres of wetlands that traverse the 4,779-acre study area. Hydrologic analysis of flow intermittency suggested that there are variable degrees of change to headwater streams immediately following mining; however, the majority of the effects are reversible through streamflow mitigation measures. Furthermore, the post-mining discharge from streams can be restored to within the range of pre-mining conditions the majority of the time. Biological assessments showed that greater than 95% of assessed stream length has maintained its ability to support benthic macroinvertebrate communities following mining and intervention (i.e., mitigation). Comparative metrics of the benthic macroinvertebrate communities showed that the biological community in 48 of the 50 sample sites is being maintained or restored across both high- and low-gradient streams. The effectiveness of intervention was further substantiated by the similarity in recovery times between streams having no intervention (median = 2.1 years, 95th percentile = 4.9 years) and streams with intervention, when recovery times were measured from the date of the intervention (median = 1.7 years, 95th percentile = 4.7 years). Changes to individual wetlands were observed between the pre- and post-mining assessments, but cumulatively a net gain of 7% in wetland acreage was realized. Hydrologic assessments were used to infer whether there was a potential that streams had been affected by mining; however, the ultimate test of stream recovery is based on biological metrics that establish the relative quality of the biological communities following mining. Overall, the hydrologic balance is being protected and the aquatic life use of streams is being maintained within the Bailey Mine’s subsidence control plan areas."

Jan 1, 2017

By James T. Furey, Laurence D. Hartzog, Graham A. Karklin

A pilot plant study was conducted to evaluate the performance of column flotation in the recovery of gold from the gold/tellurides bearing sulphide ore of the Kensington deposit (Echo Bay Mines and Coeur d'Alene Mines), and to compare the performance of column flotation to conventional "mechanically agitated" flotation, Tests were conducted in a 150 mm diameter, 60 liter glass column with ground flotation feed split from a concurrently operating conventional pilot plant, thus permitting direct comparison between the two processes. During the test program, the effects of wash water rate, gas holdup, froth depth, residence time and flow bias were examined in detail. The bulk metallurgical ore sample had an average "as tested" feed grade of about 5 git gold and 1 % sulphur, with the gold occurring primarily as inclusions of montbrayite (Au2Te3) in pyrite, with minor amounts of native gold. Conventional flotation using 60 minutes residence time across four roughing stages recovered about 97% of the gold into concentrates grading about 50 g/t Au. A single stage of column flotation roughing using 25 minutes residence time matched the conventional circuit recovery of97%, but produced grades of +150 git Au.

Jan 1, 1992

By G. E. McKelvey

A group of gold deposits in southeastern Ecuador, near the town of Zamora, have become the focus of intensive mining activity, due to their extremely high gold grade (unconfirmed reports of about 50 g/t or 1.4 oz per st, or more). The deposits at Nambija and other prospects in the district are hosted by a sequence of sedimentary and volcanic rocks that are present within a large xenolith orpendant within alkalic phases of the Jurassic Zamora Batholith. The xenolith, unknown in size, is composed of various island arc lithologies (limestones, shales, sandstones, tuffs and flows). All have been altered to some degree by skarn-hornfelde alteration assemblages. Mineralized areas appear to be localized within a linear zone containing tectonic and intrusion breccias that cross-cut a complex calcic skarn assemblage developed within the xenolith. Although the nature of the host rocks appears to have exerted some control on mineralization, the high-grade ore is concentrated along north-northeast trending breccias, faults and dikes that crosscut the flat-lying stratigraphy and skarn alteration as suggested by the strong linear trend of workings in the district.

Jan 1, 1991

By Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

Most of the future phosphate resources in Florida, which accounts for 70  percent of production in the United States, are contaminated with too much dolomite that is difficult to remove with existing industrial practices. The low-grade ore quality coupled with increased phosphate demand is of concern to the Florida phosphate industry. In order to resolve the dolomite issue, various beneficiation technologies were designed and evaluated, but none have been sufficiently successful [1]. 

By Francesco Chiappalone, Tanner Murt, Lance Waddell, Cristina Oñate Salazar

The 3RPORT project is a 5-mile-long, 16-foot-internal-diameter tunnel excavated in hard rock by Slurry TBM in Fort Wayne, Indiana. Two-component grouting can be separated into two core areas of operation: batching and underground operations. This paper addresses the challenges faced and solutions implemented in these fundamental areas. The effects of external factors and their impacts on mix design and batching of grout will be explored. Underground, challenges of monitoring parameters and ensuring a proper mix between the two-components will be discussed, focusing on the adopted technical solutions and considerations to be taken in the design stage of tailskin grout ports.

Jun 13, 2021

By George S. Barnett

The Equis and El Roble projects are located in the Cordillera Occidental of Colombia. The Equis vein deposits have sulfide ore reserves of 95.9.5.5 mt (105.770 st) grading 8.51 g/mt (0.248 oz/st) gold and 12.4 g/ml (0.36 oz/st) silver with 0.94 % copper. 1.10 a lead and 11.06% zinc. Ore reserves at El Roble are estimated as 1.1% Mmt (1.21 million st) grading 4.89% copper and 3.39 g/mt (0.099 oz/st) ,old. Geologically possible reserves at Equis may total 1.6.Mmt (1.76 million it). El Roble has the potential to contain several tens of millions of metric tons. Exploration included diamond drilling, trenching, channel sampling, rock and soil geochemistry, geophysics and tunneling. Erratic high grade samples affect the weighting of channel and drill core samples. Secondary reconcentration of gold is also a factor. Sample maps and graphs show the distribution of values to be highly variable. Geostatistical treatment of some of these data gave important guidelines for parameters such as sampling densities, drill hole spacing and confidence limits.

Jan 1, 1984

By J. van Wijk

"Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems (VTS). To investigate flow effects under realistic conditions, especially clogging effects, a 136 m high test facility for flow analysis in vertical transport has been constructed using available mining infrastructure. Tests are run in a closed circuit, using a system of downfall and riser pipelines connected to a compact sediment injection- and separation unit as well as the centrifugal pump. The riser is equipped with pressure sensors, as well as temperature sensors, flow meter, concentration meter and high speed camera to allow comprehensive analyses of the flow regime and behavior of transported material within the flow. Additional mobile measurement devices allow wear and tear analyses of pipe material. This paper focuses on the determining factors of the tests leading to the design as well as the installation and trial of the test facility itself and explains the used components and work principles. INTRODUCTION Since the 1970s several research projects had been conducted investigating in the possibility of deep sea mining. In recent times projects for deep sea mining operations have started again, considering the rising demand on natural resources, especially raw earth elements. Yet projects like the Nautilus project on the deposit Solwara 1 [1], or Japanese projects focusing on the region of Okinawa [2] and Chinese projects [3] planning on depths of “only” about 2,500 up to 3,000 m. Until now no economical deep sea mining project was realized, due to the enormous difficulties of deep sea environments. Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects, considering transportation heights up to 5 km. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems or VTS [4]. Critical parts of the system would be identified and investigated to deliver solutions and higher the technology readiness level to a level were planning of a pilot project can be considered. At first case examples for mining projects of seafloor massive sulfides (SMS, 1,600 m water depth) and manganese nodules (MnN, 5,000 m water depth) had been calculated on basis of economical frame conditions, such as planned production rates to be efficient. As depicted in Figure 1 two major possible systems had been used for comparison, airlift system and pump system, considering multiple pump stations or single pumps. Based on the results and comparisons for the calculated vertical transport systems critical components and flow effects had been identified."

Jan 1, 2018