Search Documents

By T. S. Golosinski

Most of the 154 t (170 st) truck fleets that were predominant in large surface mines in the 1970s and 1980s are approaching the end of their economic life. One replacement option considered by mine operators is a change to the 2 18 t (240 st) trucks. A comparison of load capacities between the 1.54 t (170 st) and the 2 18 t (240 st) trucks indicates a large productivity advantage in favor of the 218 t (240 st) trucks. This advantage, however, is often reduced by a number of site-specific factors. Therefore, a careful evaluation is required to define the actual benefit of changing to the large trucks. This article discusses some important factors that have an impact on truck size selection, based on several different studies. 218 t (240 st) trucks The 2 18 t (240 st) rear dump trucks were first introduced for surface mine service almost 10 years ago. However, it is only during the last few years that this equipment has gained acceptance in the surface mining industry. About 250 units were employed in surface mines worldwide at the beginning of 1992, and further purchase commitments are being made. Encouraged by the mining industry’s interest, all major off-highway mining truck manufacturers now offer 218 t (240 st) models (Table 1). At present, the existing 218 t (240 st) truck fleets are dominated by electric drive trucks. However, recent introduction of a 2 18 t (240 st) mechanical drive truck rounds out the development of this truck size.

Jan 1, 1992

By Charles Stone, Eric Wang

A method for estimating geotechnical rock loads for shallow cut and cover subway stations is presented. Localized geotechnical conditions lead to extreme variations in rock loading on the walls of subway structures. Actual lateral rock stress on these structures can range from near zero to over four times the vertical in-situ rock stress. The primary factors affecting the actual lateral stress are intact and rock mass mechanical properties, excavation sequence, localized tectonic conditions, and potential future adjacent structures. The authors recommend using the AASHTO code value of 65 pounds per cubic foot (10 kN/m3) during concept design, followed by numerical analysis of rock wedges and stress measurement for final design.

Dec 1, 2022

By Roger G. Rowe

The Crandon deposit, located in northern Wisconsin, is a 65.8 million ton Precambrian volcanogenic massive sulfide deposit which averages 1.4% copper and 5.8% zinc. The deposit is classic in origin, mineralogy and shape. Comprehensive understanding of the geology of both the deposit and the project site has been fundamental to the credibility and success of Project feasibility studies and regulatory permit preparation. Mine development in the current investment and regulatory climate requires thorough and timely application of geologic tools. From 1977-1980 geologic activities were focused on the typical objectives of orebody delineation, reserve estimation, depositional geology, and general site investigation. Results from these programs formed the basis for the Project's preliminary feasibility studies. Since 1981 further geologic investigations have provided criteria for project design, site management, and operational permitting. Activities have included mine entry position definition drilling, developing geostatistical reserve modeling, large diameter (150 mm) core drilling for mill pilot samples, rock mecha¬nics testing, and evaluation of the glacial overburden/deposit geohydrology for computer simulation.

Jan 1, 1983

By L. John Minnick

Extraction of crude ores and minerals inevitably produces various by-products either as a result of nonusable residues or as waste by-products from process operations. Thus for each 100 tons of coal extracted in a strip mine operation, one can expect to produce 25 tons, or more, of mine refuse. In addition, the amount of ash produced from the burning of coal will represent 10 to 20 percent of the weight of coal burned. With the advent of lime/limestone scrubbers now being installed on many power plants, an additional by-product is produced that in most instances is equal in volume to the sluiced fly ash. Statistics developed by the National Ash Association have indicated that sluiced waste from power plants in the United States currently exceeds 25 million tons per year (dry basis). Overall mineral industry statistics (copper mines, etc.) indicate better than 200 million tons per year. In the past it was general practice to send most of these waste materials to holding ponds or lagoons simply as a means of disposal or "throwaway" of unwanted by-products. Unfortunately modern society has reached a stage where these large quantities of waste materials are creating monumental environmental and economic problems that need urgent attention. Among these problems are concern for loss of future usable land, pollution of ground water, loss of potential mineral reserves, and loss of opportunities to recycle or use these by-products for the benefit of future generations. An example of the latter is the serious shortages of construction quality aggregates that can be replaced with some of the by-products produced from waste materials from the extractive and chemical industries.

Jan 1, 1975

By Debra Switzer, Swapnil Urankar, Douglas Watson, Steven Hunter, Chandranth Banerjee, Shashank Pathak

A hydrocyclone is a piece of equipment commonly used as a classifier in mill circuit operations. Traditionally, hydrocyclone performance is characterized by the classification efficiency parameter, such as cut size (d50c), sharpness of separation () and bypass (Rf ). A plethora of endeavors have already been made to develop parametric models to determine hydrocyclone performance that correlate design and process variables. In contrast to those studies, we made an attempt to develop an approach to derive required design parameters purely from hydrodynamic principles that provides a platform to optimize the operation of a hydrocyclone for a given application. In this selection methodology, we calculated the differential pressure at the air core, as well as the tangential velocity at the boundary of the air core from the vortex principle in a confined geometry at different operating regimes. A series of experiments were conducted using Weir’s Cavex® hydrocylone where process variables—such as solids concentration and feed flowrates—were experimentally studied to determine the key classification parameters. For the validation of the current approach we used the same process variables to derive design parameters and compared them with the existing design. The current approach can provide insights towards the selection of design parameters and can be useful for mining industry professionals to optimize different operating parameters of hydrocyclones to achieve the best performance.

Feb 1, 2024

By Anna Eleria, Joseph Welna, Jim Herber, Nathan Campeau

Constructed by stonemasons over 120 years ago, a portion of the Trout Brook Storm Sewer Interceptor (TBI) owned and operated by the Capitol Region Watershed District in Saint Paul, Minnesota, needed rehabilitation. A routine inspection of the 10-foot limestone block tunnel revealed degraded and missing mortar between the blocks, allowing significant infiltration and soil migration through the tunnel joints. Conditions, including damaged and missing blocks, were considerably worse in a 250-foot-long segment beneath a busy mainline railroad corridor. Barr’s solution included tuck-pointing to repair the mortar joints, shotcrete overlay, and construction of a hybrid cast-in-place/shotcrete “tunnel within a tunnel” to support the mainline railroad loads.

Jun 13, 2021

By Cary Hirner, Sarah Lothman, Chris Mueller, Savita Schlesinger, Mike Hanna, Ian Fitz-James

Loudoun Water is currently implementing a quarry to reservoir conversion that will improve water supply reliability in periods of drought and flexibility in water supply operations when turbidity in its Potomac River supplies are high. The Milestone Reservoir Project consists of an inter-tie to the existing Potomac River Pipeline; new pipeline and tunnel; and a pumped intake and outlet works. Planned construction involves significant risks due to underground conditions which includes hard, igneous rock and high groundwater at the creek crossing. In addition, the site is constrained by Goose Creek, an adjacent residence, active mining in a quarry next to the new reservoir, public use of adjacent park space, and the Washington and Old Dominion Trail. Working with these constraints will require close coordination with active mining operations and public and private property owners. Safety of personnel involved with construction also represents a concern with quarry high walls over 30 meters in height near the planned construction. In consideration of key projects risks, Loudoun Water determined that an innovative CMAR delivery approach provided the best opportunity to achieve its goals in quality, innovation, front-end cost and schedule certainty, and operational flexibility and reliability. What matters most to Loudoun Water is the value in having a builder participate in the design process where key decisions can be made based on consideration of risks, cost, schedule, quality, and operability and maintainability of the system. While a progressive design-build delivery model may have produced similar outcomes, Loudoun Water had already invested in substantial development of the design for the work, and ultimately, CMAR provided Loudoun Water the opportunity to retain the partnership with the design team while gaining valuable input from a contractor. Among the challenges with CMAR in the Commonwealth of Virginia is a substantial limitation on self-performance corresponding to 10 percent of the construction value of the work. A significant industry outreach program was initiated by Loudoun Water to encourage participation with incentives in contract terms that allowed for the CMAR Contractor to make a reasonable profit. This paper reviews the CMAR procurement process and discusses contract incentives that were adopted to promote the work within the constraints of contract law in Virginia.

Jun 13, 2021

By Chen Chuanqing

The Mining design system is a CAE (Computer Aided Engineering) software and was developed as designer-oriented, interactive mode software to perform geological and mining design calculation and graphics. To perform geology and mining design, the deposit model files created by the software "Deposit Modelling System", are transferred to the environment of graphics support software, then a specially developed drafting submodule can be selected to proceed to interactive graphics design. If it is necessary to calculate the grade and quantity of a particular part of the ore-body, another submodule will be called and run. The resulting file is 'transferred back, and the recalculation program takes the data from the file and refers to the deposit model file to create a summary reserve report: The minimum hardware configuration of the system are IBM-AT Basic work station with high resolution graphic monitor and peripherals needed are digitizer, plotter, printer.

Jan 1, 1989

By Greg Sanders, Bill Lueck, Michael Gilbert, Mahmood Khwaja

"The city of Minneapolis contracted with CDM Smith to update and provide a conceptual design for improvements to mitigate surcharge flooding in the Central City Storm Water Tunnel System (CCSTS). As a part of the project, CDM Smith conducted a field survey and condition assessment of the existing tunnel system. Information from the survey was then used to update the existing XPSWMM model and develop system wide alternatives.The CCSTS provides storm-water runoff drainage for nearly the entire area of the city’s downtown commercial district. The system consists of deep storm-water tunnels constructed in the St. Peter Sandstone, approximately 21 m (70 ft) below the street’s surface. The primary tunnels comprising the Central City storm water tunnel system are located below Hennepin Avenue, Nicollet Mall, Lesalle Avenue, Marquette Avenue South, 2nd Avenue South, South 5th Street, Washington Avenue South, Portland Avenue South, 2nd Street South, and Chicago Avenue South, as shown in Fig. 1. This network of tunnels conveys the runoff from a 305-acre tributary area that is generally bound by Hennepin Avenue and 1st Avenue North to the east, 12th Street to the south, 4th Avenue South and 7th Avenue South to the west, and 2nd Street South. These tunnels were constructed between 1936 and 1940, except for the Marquette Avenue South tunnel, which was constructed between 1963 and 1964.The CCSTS operates as a gravity flow system. These tunnels were constructed within the St. Peter Sandstone layer of bedrock and emerge from the bedrock at the Mississippi River below St. Anthony Falls. The Central City and the adjacent Chicago Avenue tunnel system converge into a single outfall at the Mississippi River. The runoff discharges from the converged outfall to a side channel of the Mississippi River, called a tailrace, located near the Guthrie Theater. The Minneapolis Division of Surface Water and Sewers provided 32 historic plats detailing the plan and profile of the tunnel system.The tunnel plans show nine different cross-section configurations. Eight configurations within the overall system generally show the same geometric “cathedral” shape with the inside dimensions varying from 1.2 to 1.8 m (4 to 6 ft) in width and 1.8 to 2.4 m (6 to 8 ft) in height. For analysis, these eight configurations were reduced to three configurations with regards to tunnel liner, cross-sectional area and support. For simplicity, the three configurations are described according to the three types of tunnel support used during construction: none required, light timber and heavy timber"

Jun 1, 2019

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

This study investigated the performance of citric acid as lixiviant for cathode material from end-of-life lithium-ion batteries (LIBs). Black mass containing 84.2 weight percent MNC (LiNi0.45Mn0.4Co0.15O2) and 15.8 weight percent LCO (LiCoO2) material was leached at solid-to-liquid ratios of 20, 50 and 100 g/L. Leaching with 1.5 M citric acid, 2 volume percent H2O2 and a solid-to-liquid ratio of 20 g/L at 95 °C extracted 90 percent Co, 95 percent Li, 94 percent Mn and 94 percent Ni within 20 min. At the highest solid-to-liquid ratio of 100 g/L with 1.5 M citric acid, 10 volume percent H2O2 and 95 °C, 84 percent Al, 84 percent Co, 87 percent Li, 86 percent Mn and 96 percent Ni were leached after 40 min, producing a leach solution containing 0.68 g/L Al, 20.0 g/L Co, 6.0 g/L Li, 13.6 g/L Mn and 19.3 g/L Ni. Using stepwise addition of H2O2, instead of initial bulk addition, did not significantly improve the leaching efficiency but did reduce the required leaching time. Temperature control of the reactor was also more manageable with stepwise addition of H2O2, and evolution of gas was less vigorous. It was observed that the leaching efficiencies of Co, Li and Mn decreased slightly at solid-to-liquid ratios of 50 and 100 g/L, while the leaching of Ni increased slightly. The solution leached at 20 g/L could be stored for six weeks without any spontaneous precipitation. However, solutions leached at 50 and 100 g/L showed changes in concentration after one month of storage, suggesting that processes that have a large material throughput and use high solid-to-liquid ratios around 100 g/L must ensure that the solutions are not stored for extended periods of time.

Apr 1, 2025

By J. Sohn

The most promising near-term alternative to fuel cell driven vehicles is probably Hybrid Electric Vehicle (HEV or EV) technology. HEV technology combines the best characteristics of fuel-driven engines, electric motor drives, and energy storage components. It is designed with a combustion engine that functions as the primary power source, and an electric power storage system that functions as the secondary power source. The presence of the secondary power source allows designers to size the combustion engine for cruising power requirements. A new energy source for HEV or EV market will become lithium ion batteries (LIBs) in the near future. LIBs for HEV or EV has large scale about more 10,000 times than small size one for IT devices in order to achieve high electric density/capacity and high efficiency, etc. In those reasons, physical treatment of the batteries is more difficult for stable dismantling in comparison with the smaller one. Hybrid vehicle sales will grow by nearly 400 percent during the next seven years, according to a new report from analyst firm ABI Research. By 2013 hybrids will make up 6 percent of annual U.S. auto sales. The traction battery pack will become air-cooled LIBs which consists of several modules of Li ion battery and connected in series/parallel configuration to provide about >450 VDC, >150 kW peak power, and >80 Ah capacity. As the use of these batteries tends to increase significantly for the next years, it is relevant issues that development of new recycling methods as well as optimization of existing processes to treat spent LIBs for HEV have being addressed in order to obtain sustainability. In this study, physical treatment containing stable electrical discharge of spent LIBs for HEV was carried out for recovery of valuable metals from the batteries. Also In order to increase the yield of valuable metals through physical treatments such as electric discharge of spent batteries, crushing, and classification, we also focused on the recovery of cobalt from +8 mesh fraction due to its large portion in crushed intermediates.

Jan 1, 2010

By Erik Sundström, Magnus Nygren

Having seen significant improvements to accident rates in the last 40 years, companies in the Swedish mining industry now show a greater focus on the development of safety cultures throughout their organisations and workplaces. However, there is a lack of research examining the different safety initiatives and strategies practiced in the industry today. This study explores the potential influence and consequences such initiatives may have on the development of safety cultures in the Swedish mining industry. Twelve interviews with experts on safety initiatives from four different Swedish mining organisations were conducted and analysed in a process based on qualitative thematic analysis to identify notable connections to safety culture development. The results of these interviews highlight proclivities in the implementation and use of safety initiatives such as subjects of focus, methods and desired effects. This enables the interpretation of the conceptualisation and methods for the development of safety culture in these organisations based on their approaches to safety development. We believe the results of this study can serve as support for discussions on safety culture development in the Swedish mining industry, and be of interest for international mining industries, in addition to approaches to research in this field. However, we also believe it is important to emphasise the opportunities to approach safety culture in mining from different perspectives than those common today.

Jul 19, 2023

By C. R. Everly

"The purpose of this paper is to review the most effective methods of reducing chloride transfer and chloride removal in the solution extraction and electrowinning (SX/EW) process. Elevated chlorides in electrolyte have various negative effects including a reduction in current efficiency, increased handling costs at rod plants and smelters, increased anode corrosion, cobalt losses due to increased electrolyte bleed, degradation of HDPE piping, and increased corrosion in the SX/EW plants. Historical controls that Sierrita has used to control chloride transfer, in order of effectiveness, have been chloride gasification at the EW that is directly correlated to amperage and chloride concentration in electrolyte, wash stage bleed and efficiency, width and velocity of aqueous bands, and electrolyte bleeds. Maintaining high bleed rates and high amperage settings has been a challenge with decreasing pregnant leach solution (PLS) grades, so keeping chlorides out of the electrolyte has become imperative. The effectiveness of reducing aqueous entrainment, optimizing wash stage efficiencies, and improving organic quality to reduce the transfer of chlorides to the electrolyte are illustrated in this study. INTRODUCTION The transfer of impurities from PLS feed streams to electrolyte in the Copper Solution Extraction process is a very common problem and is the reason that the wash stage exists in most SX operations. The main impurities affecting the SX process are iron, chloride, nitrate, and manganese. Elevated chlorides in the electrolyte have various negative effects including reduced current efficiency, increased handling costs at rod plants and smelters, increased anode corrosion, increased cobalt losses due to increased electrolyte bleed, degradation of HDPE piping, and increased corrosion in the SX/EW plants. Freeport-McMoRan Sierrita Hydromet is unique in that a high-chloride byproduct stream from the molybdenum process is pumped into the SX raffinate solution pond. This byproduct steam accounts for the majority of chloride introduced to the circuit, and over the years has built up to a point where 4000ppm chloride is consistently in the PLS feed to the SX. Concentrations of chloride over 70 ppm in electrolyte will result in downgraded cathode, so it is important to limit chloride carryover from SX as much as possible. Historically, Sierrita has been able to manage chloride levels with reactive techniques including increasing electrolyte bleeds and rectifier amps. Decreasing copper in PLS has made high amps harder to maintain, and increasing bleed rates have a direct impact on production goals."

Jan 1, 2015

By J. A. Herbst

Successful transitions from micro- to macro-engineering are the keys to effective technology transfer between research and development organizations and industrial end users. At the same time, it has proven to be one of the most difficult tasks that the minerals industry has had to manage. Typically, developers of fundamental information concerning how mineral processing subsystems work have been academics and government scientists. These are the individuals giving the most important input to micro-engineering models that can benefit industrial operations. Publication is the usual route for "attempting" to transfer this technology to the end users. Unfortunately, with such publications, very little direct communication occurs concerning real industry needs or the future steps required to make the particular micro-engineering model useful. In the past, the industry has relied on in-house R&D groups and plant metallurgists to "translate" publications, to provide useful macro-engineering tools for plant applications. To some extent, engineering companies have also been asked to serve this function. However, these firms have been rather ineffective in this area since their conservative nature has caused them to look rather suspiciously at new technology. This approach to technology transfer has worked, albeit clumsily, for the last several decades. This communication system is now on the verge of total collapse due to conditions of the minerals industry. Mining companies can no longer afford the significant overhead expenses of specialized technical staffs. Universities are finding it extremely difficult to interest US students in mineral engineering programs, and funding for such programs is weak. Faculty members involved in micro-engineering research today tend to focus on pure (non-application-oriented) research.

Jan 1, 1992

By William G. Pariseau

The purpose of this paper is to present a design procedure for the quantitative estimation of support load requirements in underground mines. Emphasis is upon the basic features of support behavior common to a large variety of support systems-bolts, timber sets, stope fill, steel arches, concrete liners and so forth. A strong reliance is placed upon fundamental principles and modern computing techniques for their quantitative implementation. Example problems illustrate the approach. Where artificial support is required, the ground in the vicinity of the face usually stands unsupported long enough for the support to be installed. At the time of installation, the load transferred to the support from the adjacent rock is essentially zero, although in some cases there may be an initial set load, for example, from timber blocking. With the passage of time and advance of the face, ground motion loads the supports. If the support system is properly designed, then the additional loading poses no threat to the safety and productivity of operations. If not, then difficulties may arise including high maintenance costs, hazardous work conditions and reduced productivity. Of course, over-design can be equally wasteful. Quantitative estimation of support loads is therefore essential to overall efficiency in mining.

Jan 1, 1975

The results of studies to ameliorate acid mine drainage by retarding the rate of oxidation of pyrite at source are discussed. In the transpassive region, pyrite oxidizes by reactive dissolution, mass transfer through the product layer and diffusion in the bulk solution. One can decrease the rate of pyrite oxidation by inhibiting either oxidation reactions or cathodic reactions. It is demonstrated in this study that some surface active reagents extend the passive region by affecting both the anodic and cathodic processes. The extension to higher potentials occurs by inhibition of the anodic dissolution process whereas to lower cathodic potentials through decrease in the rate of reduction of molecular oxygen and/or ferric ions. To retard the oxidation of pyrite by ferric ions, which is considered to be the dominant oxidant under conditions of acid mine drainage, it would be necessary to restrict mass transfer or promote complexation of ferric ions at the surface. Imidazoline based reagents were found to be most effective in meeting this goal.

Jan 1, 1994

By J. K. Wilmshurst

Absorption, emission and reflection techniques for the study of [molten] inorganic materials at high temperatures have been critically examined. In general, the reflection technique is the most satisfactory for tine study of pure materials, while the absorption, and possibly also the emission techniques, may be useful for studies of certain dilute solutions. In the present investigation infrared emission spectra for sodium nitrate and silver chloride were obtained together with absorption spectra derived from reflectivity data by the method of Robinson and Price for sodium nitrate, silver chloride, lithium and potassium fluoride and their 1:2, 1:1 and 2:1 mixtures and for solutions of zirconium tetrafluoride in lithium-potassium fluoride (1:1) and sodium-potassium fluoride (1:1). It is concluded that vibrational spectroscopy cannot give unambiguous information concerning the existence of complex ions in fused salt, mixtures.

Jan 1, 1963

By George R. Mitchell

It is a common observation that objects having, different; temperatures exchange energy by radiative transfer. The quantity of radiant energy emitted by an object is a definite function of its temperature. Therefore, a measurement of emitted radiation, by means of a calibrated radiometric instrument, provides a temperature measurement without contacting the emitting object. The physical laws describing radiant energy transfer and their application to remote temperature measurement form the substance of this paper. The energy radiated by bodies having temperatures up to 4000°C is largely in the infrared spectral region. The infrared spectral region is that part of the electro-magnetic spectrum having wavelengths longer than visible light and extending to the microwave region. The wave-lengths range from 0.7 micron (1 micron = 10-4 cm) to 1000 microns. In general, infrared radiometry deals, with the methods of measuring energy flux in the 1 to 15 micron region of the infrared spectrum.

Jan 1, 1960

By P. Rusin

A new bacterium, Thiobacillus cuprinus, can extract copper from chalcopyrite as rapidly as T. ferrooxidans. On solution with and without nutrient amendments and bacterial growth media were supplemented with T. ferrooxidans or T. cuprinus in shake flask studies. Both species extracted -42% of the copper using growth media. In one case, T. cuprinus solubilized approximately twice as much copper as T. ferrooxidans utilizing a seeded On solution. Thiobacillus prosperus also oxidizes chalcopyrite and tolerates high chloride concentrations. These sulfide-oxidizing bacteria are representatives of the mixed microbial community found in sulfide dumps. Rates of biological copper extraction from sulfide ores, using the native microbes, have been significantly enhanced by amending On solution with PGM.

Jan 1, 1994

By Arcy R., D&apos George

Removal of S02 from smelter gases is being investigated, using an innovative technique that results in the almost simultaneous recovery and production of elemental sulfur. S02 is removed from the gas stream by scrubbing with suitable aqueous salt solutions or high-boiling organic fluids. The S02-laden liquor is then reacted with H2S Crystalline, high-purity sulfur is instantly precipitated and, after filtration, the regenerated liquor is recycled. The H2S required for the process is produced by reacting a portion of the recovered sulfur with hydrogen or with methane and steam. The chemistry and results of preliminary laboratory research are discussed.

Jan 1, 1969