Search Documents

By Dongxu Jia, Chen Cao, Shuangwen Ma, Jun Han, Huibin Ma

Coal bump, or coal burst, is one of the catastrophic disasters in underground coalmine. Among them, approximate 80% of recorded destructive burst events were occurred in mining roadway. The bump panel is often formed by hard coal seam and hard main roof; however, the cause and course of the bump events are not understood yet. This study provides a fundamental theory for the causality and progress of a coal bump event occurred in longwall roadway. Considering hard roof condition commonly existed in bump panels, we think that the abutment pressure induced by suspended roof behind the working face is the trigger of a coal bump event occurred in the roadway. Once high abutment pressure is concentrated on the hard coal seam around the working face, the roof and the coal around the working face form a seesaw-like structure, which leads the roof in front of the working face moving upwards. The movement of roof uplifting in front of the working face is a well evidenced phenomenon in practice, namely, roof rebounding, which causes unloading of the normal stress on the roof-coal interface around the roadway. A rib coal block bump mechanical model has been developed to establish the critical equilibrium equation of the coal block. Result shows that, the force source of coal bump is the horizontal ground stress perpendicular to the rib surface; and the slippage of the coal block is caused by the unloading of the normal stress acting on the roof-coal interface. Based on the causality and consequence theory of coal bump developed in the paper, several new prediction and prevention measures have been developed, including roadway design and in-tunnel reinforcing methods. The commonly used prevention measures in present have also been discussed. This paper presents a comprehensive explanation of coal bumps occurred in longwall roadways, from abutment pressure at working face forming seesaw structure to roof rebounding leading slippage of the rib coal mass into roadway, which provides a fundamental theory for coal bump causality mechanism and prediction and prevention technology.

Apr 26, 2022

By X. X. Shao

Dewatering of ultra-fine clean coal slurry to a low moisture level of20 percent is difficult using the conventional techniques. A novel approach, which utilized mixing of fibrous waste material, such as paper, carpet and wood, with coal slurry prior to dewatering was developed. It was found that addition of about 10 Kg/t of carpet fibers or 5 Kg/t of raw paper pulp lowered the filter cake moisture from 22.5 to 18 percent. The compressive strength of the filter cake improved from 0 to 4.5 Kglcm2 and impact resistance from 0 to 4. The experimental data indicated that the handling character of the dewatered fine coal was improved significantly.

Jan 1, 1998

By George J. Conroy

Results of a long-term program of electrical parameter measurement in under-ground coal mine working sections, performed by The Pennsylvania State University under U. S. Bureau of Mines sponsorship, are utilized as the basis for an analysis of the electrical energy requirements during operation. A model section is hypothesized, developed from the average or most representative characteristics as determined from tabulations of the measurements. Performance factors of the model section's machine complement are then analyzed, particularly with regard to the energy required per ton of raw coal cut and delivered from the section. Results are given in kilowatt-hours per ton.

Jan 1, 1977

In this paper, a number of novel hypotheses that provide a fresh perspective on the characterization of strata movements associated with longwall mining are developed by analyzing subsidence measurements with an influence- function-based computer program. With this influence-function technique, easily obtained surface displacements can be used to determine some of the complicated, expensive, and difficult to measure movements of the immediate roof strata in a longwall panel. The primary hypothesis developed by this analysis proposes the existence of an area of partial roof caving near the edge of a panel called the "edge effect." A second hypothesis, interrelated with the first, promotes the importance of the effect of gate-entry closure on the observed strata movements. Both the primary edge effect hypothesis and the secondary hypothesis concerning gate-entry closure are justified and quantified in an extensive analysis of surface subsidence that uses supporting information from related theories, design criteria and insitu measurements. Next, the edge effect and the gate closure hypotheses are extended further and used to provide an explanation of the complex subsidence interaction of adjacent longwall panels in what is termed a "redisturbed" effect. Finally, in the conclusions of this paper, the importance of accurately understanding these longwall strata movements for proper subsidence prediction or gate design is stressed.

Jan 1, 1986

By Michael Davis

In the fairly recent past, with a history of cheap and abundant energy, it has been possible to predict with reasonable confidence that world energy demand would continue to double about every 15 years. Those who attempted to forecast the role of nuclear energy in future electricity generation could also start with the fairly safe assumption that electricity demand would increase even faster : with a doubling in demand about every 10 years. To estimate the likely future world demand for uranium it was then necessary to introduce a number of other assumptions including the rate of penetration of nuclear energy, the timing and the specific fuel requirements. This series of assumptions naturally compounded the uncertainty, but, remarkably, usually led to future uranium demands being overestimated. Such a bias which has almost always been observed in predictions made over the past 20 years has increasingly made uranium producers sceptical when expected to match the forecast demand with increased production capacity and supporting reserves. This scepticism has, of course, been reinforced by the persistence so far of a buyers' market in uranium throughout the entire period of emergence of commercial nuclear electricity generation.

Jan 1, 1974

By M. L. Free, N. Dhawan, M. S. Safarzadeh, J. D. Miller, M. S. Moats

"The drum agglomeration of nickel laterite and gold ores has been optimized through the design of experiments (DOE) using a Taguchi L16 (45) orthogonal array to determine the optimum conditions for maximizing average agglomerate size and minimizing the amount of fines. The effects of controllable operating factors including moisture content (nickel laterite ore: 34-37%; gold ore: 7-10%), retention time (2-3.5 min), drum speed (15-45% critical speed), drum load (nickel laterite ore: 8-32 %; gold ore: 6-22%) and acid concentration (150-600 g/L) on the performance of the agglomeration process were studied.For nickel laterite ore, maximum average agglomerate size and minimum percent fines (-1 mm) occurred under the following conditions: drum load (23.7%), moisture (36.5%), time (3 min), drum speed (30% critical speed) and acid concentration (150 g/L). Under the studied nickel laterite ore conditions, the most effective parameters for maximizing average agglomerate size and minimizing the amount of fines were found to be drum load and acid concentration, respectively. Drum speed had a statistically significant effect on minimizing the amount of fines. Maximum average agglomerate size and minimum percent fines (-1 mm) for gold ore occurred under the following conditions: drum load (19.3%), moisture (8.5%), time (2 min 15 s) and drum speed (40% critical). The most significant factors for maximizing average agglomerate size and minimizing the amount of fines for gold ore were found to be drum load, time and moisture.IntroductionSeveral heap leach operations have experienced problems in terms of poor recovery due to percolation issues caused by low-grade complex ores, tailings and clayey deposits. Poor percolation can lead to low metal extraction due to solution channeling or the development of impermeable/dead zones within the heap (Dhawan et al., 2012; Kappes, 2005). Improper heap building practices such as the use of loose agglomerates and inadequate attention toward the presence of clay minerals have been among the main reasons for percolation issues. During the transport of ore material, severe segregation of the material can occur. To overcome percolation problems, a major improvement was made through the introduction of agglomeration prior to ore placement. If the ore particles and agglomerates are of similar size, segregation can be avoided to a great extent (Dhawan et al., 2013; Kinard and Schweizer, 1987; McClelland and van Zyl, 1988). Agglomeration improves the uniform percolation of solution through ore heaps and is applicable to many ores, wastes and milled tailings (Bouffard, 2005; Dhawan et al., 2013). Manning and Kappes (2005) reported agglomeration/ stacking accounts for ~14% of the total heap leaching operating cost. The cost of binder is a primary contributor toward the total cost. Also, the lack of consistent quality control tests for agglomerate often leads to operational problems. The details are mentioned elsewhere (Dhawan et al., 2013). Considering the significant contribution of the agglomeration/stacking step toward the total heap leach operating cost, it is appropriate to study the agglomeration behavior and its optimization for two different ores. The reason to study the same parameters for different ores is the fact that significant variability in the agglomeration behavior of different ores has been reported to exist in industrial operations."

Jan 1, 2015

By V. K. Gupta

The experimental results of some wet batch and continuous grinding experiments carried out in a 40 x 40 cm grate discharge ball mill have been analyzed for the variation of the grinding rate parameters, Si, with various operating conditions using a linearized population balance model. The wet grinding tests were carried out under conditions which were very similar to those encountered in the actual practice in plant operation. Well distributed -4 and -20 mesh feeds of two complex pyritic ores were used. The volume-percent solids in the pulp ranged from 30-40, the particle load from 5-8 kg, and the solids feed rate from 70-1 10 kg/hr.

Jan 1, 1981

By I. S. Parrish

As noted by McKinstry (1948), "How to deal with erratic high samples is one of the knottiest problems in ore estimation." He described a variety of approaches and methods to alleviate the problem through the averaging and weighing of assay data and by "cutting" or "clipping" of the erratic assays. Bird (1991) elaborated on ways of dealing with the nugget effect (erratics). He listed several procedures for cutting. Bird's list has been reproduced and/or added to by several authors including Vallee (1992) and Stone and Dunn (1993). Missing from each of these otherwise excellent reviews is a definition, description or guideline to recognition of an "erratic," or just where or when cutting is warranted or justified.

Jan 1, 1997

By R. K. Mehta, S. K. Dhar, R. R. Mallepali

Introduction The incentives for developing a distributed form of the comminution model include: • for describing the heterogeneous comminution behavior of multiphase mineral systems (i.e. realistic ore bodies, such as complex sulfide ores consisting of chalcopyrite, galena, sphalerite, pyrite and siliceous minerals) and •for generating, for various locked and free particles, in situ, microscopic, breakage behavior such as the mode of fracture (intergranular vs. transgranular), the relative rates of breakage and the breakage distribution. However, the computational difficulty and the effort made in estimating a large number of parameters (Andrews and Mika, 1975; Wiegel, 1976; Herbst et al., 1985, 1988) do not justify the utility of this approach. Also, obtaining the results experimentally is very tedious and time consuming if using this approach. Although recent work in this area (Choi, Adel and Yoon, 1987; Mehta, Adel and Yoon, 1989, 1990) showed good results for liberated particles, the quality of the estimation and prediction was poor for locked particles. Attributing this to the complex breakage behavior of locked particles, it was concluded that additional constraints, and possibly modification in the breakage distribution functional form for locked particles, were necessary. However, further mathematical analysis revealed that the method previously used was in error. The purpose of this technical note is to present the correct solution methodology used in solving the general model equations of a multicomponent mineral system containing multiple classes of locked particles. Previous work and connection The general form of the comprehensive, distributed-component comminution model has been described as (Herbst et al., 1985) [d (m (0) -[ I - B ] S_ m(t) = A m(t) (1)] where [A] is the fundamental matrix/state companion matrix, commonly referred to, in the comminution literature, as the "mill matrix." Note that for a distributed-component comminution model, this is a full, general, real matrix, unlike a lower triangular matrix for a simple grinding model or a lumped-binary grinding model with one locked-particle class (Herbst et al., 1985, 1988). Also note that all of the underlined letters refer to matrices. Herbst et al. addressed the difficulty in arriving at a closed form of the analytical solution of Eq. (1) via similarity transformation [IT J inv (T)]]. This difficulty occurs for several reasons: •[A], as a general real matrix, may have complex eigenvalues and complex eigenvectors. •More importantly, there is no guarantee that a set of eigenvectors of [A] will turn out to be independent. An attempt was made to solve this problem by implementing a decomposition method. With this technique, the mill matrix was decomposed into a sum of lower and upper triangular matrices [(i.e., A = L + U)]. Then the solution was obtained using similarity transformation (Mehta, Adel and Yoon, 1989, 1990). [e(At) = e(L+U)t = e(Lt).e(Ut) _ [ TL Jt- (t) inv(T_L)] [-Tu Ju (t) inv(Tu)]] [But, unfortunately, e 1+U = e t . eu is true only for scalars and not for matrices (i.e., eL+u# eL- eU) unless they commute. In other words. eAt = e(L+u)t= ekt - eU' if LU = UL. Hence, this decomposition scheme must be replaced by a mathematically acceptable method known as the "splitting method"]

Jan 1, 1994

By Leonard Harris

Good morning ladies and gentlemen. I would like to thank Hans von Michaelis for inviting me here today to talk to you on the subject of "How to Reduce Capital and Operating Costs at Heap Leaching Projects". The comments I have to offer are based on my experiences in gold heap leaching by Newmont Gold Company in Nevada, by Newcrest in Western Australia (formerly Newmont Australia), by Minera Yanacocha in Peru, by Penmont in Mexico, by Z­Mont in Uzbekistan, by the Hochschild Group in Peru and expe­riences in copper heap leaching by Magma Copper Company in Arizona and as a consultant on several other smaller projects worldwide. These comments are a mixture of technology, ideology, philos­ophy, strategy, logic and opinions and might be looked at by many of you as "one man's view". I like to look at them as "a view from the bridge". Let me add that it doesn't bother me that you may not agree with my comments and that I would be interested in your comments or criticisms at the end of this presentation. I don't intend to discuss the details of the mineralogical and metallurgical test work. I will assume, for this talk, that the test work has been conducted very carefully and that the ore in ques­tion has been determined to be heap or dump leachable. Let's begin with a couple of don'ts! ! First, "don't build the mill until you have a mine". This might sound to many of you as fundamental but believe me it continues to happen. The minable reserves should be well known and established as being economical to mine and leach. NPVs, ROis and IRRs are fine if you can be sure of the gold price you use in your calculations. The best method is to carefully estimate the capital cost and, most importantly, the operating cost per ounce of gold recovered which should include the repayment of the borrowed capital and the interest thereon. For example, if the operating cost under these conditions is $200 per ounce, you have a project. If it is $400 per ounce, walk away f om it. Incidentally, the same prin­ciple can be applied to projects involving other metals such as silver, copper, lead, zinc, etc. The second don't is - "don't be sheep". Don't climb on the bandwagon with respect to design and operation because every­one else does it a certain way. Keep an open mind, be versatile, look for change, look for every possible innovation for reducing capital and operating costs. Beware of those who will tell you "we tried that it won't work" or "it's too expensive" or "that's a crazy idea" , <' ''what do you know about mining - you are a metallurgist aren't you" or "what do you know about metallurgy - you are a miner aren't you" or "only geologists can handle this issue". Be careful about pigeon-holing people according to their basic degree and experience. In these days of low metal prices, we need to consider everybody's ideas, as crazy as some of them might seem.

Jan 1, 1998

By N. W. Johnson

The behavior of non-sulphide gangue in chaloopyrite flotation circuits has been investigated. Plant and laboratory tests were carried out on five different ores, and linear relationships were found to exist between the rates of recovery of water and free nonsulphide gangue in the concentrates although there was evidence from pilot plant tests that these were linear approximations to parabolic curves over the limited regions which were observed. There was evidence that the free non-sulphide gangue enters the concentrate by hydraulic classification and a classification function has been proposed to define this behavior. This function is suitable for inclusion in a mathematical model of the process.

Jan 1, 1972

By Kirk Carlton

This paper deals with a group of subjects so familiar to all of us that we might question the need for discussion. Even so, nearly every day&apos;s business turns up expensive examples of differences in understanding, misdirected assumptions and incomplete technical purchase documents. As our international activities increase, so do these problem areas. Their expense in both money and embarrassment gives rise to this attempt to focus a little extra attention on technical criteria and specifications. The two terms ?criteria? and "specifications" are, we believe, worth separating with respect to meaning. They should not be used interchangeably, although they often are. Criteria are by definition "standards for judging", whereas specifications are "enumerations of particulars". In relation to plant or project engineering, the criteria are the general rules and data which apply to the whole project and the specifications are the further listing of detailed requirements for specific contractual items or pieces of equipment. We&apos;ll look a little more closely at specifications after we give another minute or two to this "criteria" subject,

Jan 1, 1973

By Charles H. McGuirk

The movement of iron ore, limestone and-coal on the great lakes involves an intricate transportation network between mine, dock, vessel, railroad and consumer. The system requires that stockpiling be performed at certain points in the pipeline because of the seasonal closing of the lakes, traditionally, this has been accomplished at origin and destination with a substantial cost. Impact to both the shipper and consumer, From the time that the raw material is removed from the ground, expeditious handling and movement to final destination is threatened by a series of potential delays. An initial movement from mine or processing plant to the upper lake port must be coordinated between rail equipment and dock facility, As each vessel is loaded, a schedule must be developed which routes the cargo to an unoccupied lower lake port. However, if the vessel is not delayed by unpredictable weather conditions on the lake, the boat may still arrive at a port congested with other vessels awaiting their turn to unload.

Jan 1, 1973

By R. R. Klimpel

The efficiencies of plant scale comminution processes are often evaluated by various indices that are calculated and/or measured somewhat independent of the performance of any associated downstream froth flotation processes. In order to compare some specific comminution factors such as energy utilization, media consumption, equipment utilization time, etc. comparisons of comminution efficiency independent of flotation behavior are appropriate. However, as more and more detailed plant level information is gathered on the joint and highly interactive nature of comminution and froth flotation, it is becoming increasingly obvious that knowing and using simple efficiency indices are not enough. What is needed are more performance related measures of the efficiencies of the combined size reduction -froth flotation system for effective plant level economic optimization to occur. The purpose of this paper is to present some examples of important interactions that influence the joint efficiencies of size reduction and froth flotation processes.

Jan 1, 1998

By B. F. Westfall

Throughout the 1960&apos;s and 1970&apos;s world trade grew rapidly, reaching a peak of USS1.8 trillion in 1980. Since then the world recession of the early 1980&apos;s shrunk trade to about US$1.6 trillion. The reduced cash flow to developing economies made it difficult to service their huge international debts, Nowadays lenders are reluctant to grant Third World countries additional credit. The shortage of export financing, plus trade barriers set up by developed countries, is further inhibiting international trade. Therefore, countries are turning to new and creative alternatives to financing imports of consumer as well as of investment goods. Non-cash transactions, including different forms of countertrade, are rapidly growing alternatives to traditional trade financing patterns. In 1983 about 30% of international trade, or close to US$600 bill ion, were presumably done by non-cash transactions, up from barely 2% in 1976. By year 2000, half the world trade is likely to be conducted on basis of barter. As of mid-1984 some 88 nations used countertrade regularly and Governments of at least 15 Latin American countries had arranged or mandated commercial countertrade.

Jan 1, 1986

By W. W. McClintock

A column flotation system was designed to conduct release analyses of a very finely disseminated, stratiform, copper ore from the Denali Copper Prospect, Alaska. Chalcopyrite is finely disseminated in a carbonate matrix and pyrite is disseminated in both the chalcopyrite and gangue, requiring grinding to 20 microns for adequate liberation. A 25 mm x 2.4 m glass flotation column was designed. The ore and its flotation tailings were repeatedly floated to obtain a rougher concentrate, which was repeatedly floated to produce release fractions. These were analyzed for copper, iron calcium and magnesium. Release curves were plotted. The procedure was replicated at each of two grinds; 99% and 88% passing 37 microns (400 mesh), and should find application for flotation characterization and process selection. Bond grindability work was also conducted.

Jan 1, 1994

By Gh. Crutu

During exploration and exploitation of complex ores, waste dumps that contaminate severely the environment and in particular soils and waters, are genetated. The most hazardous pollutants are heavy metals and metalloids (e.g As, Mo, Pb and Cu) as well as radionuclides (e.g U and Ra).

Jan 1, 2008

By J. T. Carlson

Dolomite is an objectionable impurity in phosphate ores, due to its MgO content. Even though dolomite and apatite liberate at a coarse size, the very similar densities of dolomite and apatite makes density separations difficult. However, if operated correctly, jigging can be a very efficient process. This has led to the development of a unique laboratory scale jig that allows for easy alteration of effective jigging properties. Key jigging parameters have been investigated for the separation of dolomite from phosphate ores. It was found that a pulsation rate of approximately 200 pulses/minute worked best for separating dolomite from apatite.

Jan 1, 2010

By S. A. Elmquist

Research activities performed by Cleveland-Cliffs Research and Hibbing Taconite plant personnel during the last decade have resulted in the development of an improved autogenous mill grinding circuit. Minus one (1) inch autogenous mill trommel oversize material, con-sidered to be a critical size, is magnetically cobbed and then crushed to 100% minus 3/8" prior to reentry into the feed end of the mill. Autogenous mill capacity increases, up to 25%, have been measured in pilot plant tests using this approach and are also anticipated for the Hibbing Taconite concentrator which presently has reached a 15.5% improvement.

Jan 1, 1994

By Van Price

Some technical developments of the National Uranium Resource Evaluation Program which are of general application in geochemical exploration are being studied. Results of stream water and suspended and bottom sediment analyses are compared for an area near Williamsport, Pennsylvania. Variations of uranium content of water samples with time in the North Carolina Piedmont are seen to correlate with rainfall. Ground water samples from coastal and piedmont areas were analyzed for helium. All media sampled provide useful information when properly analyzed and interpreted as part of a total geological analysis of an area.

Jan 1, 1979