Search Documents

By E. Tarshizi

This research project demonstrates the application of a mine system simulation and animation model in enhancing the efficiency of a truck-shovel operation and reducing the haulage environmental impact in an open-cut coal mine. In any mine, a key objective is to have enough equipment for production and not have excess to where it is counterproductive. Due to the advent of responsible mining, environmental regulations, and eco-friendly practices, these factors must also be considered in the analysis. The over-trucked situation at a mine will be discussed, i.e. when the number of trucks exceeds the optimum number of trucks a mine should have for the most productive/profitable mining operation. When the system has an excess number of trucks, truck utilization is reduced which impacts mine operation, capital costs and the environment, through unnecessary truck purchase, energy use, air pollution etc. A hypothetical surface coal mine layout was used for the simulation model.

Feb 23, 2014

By İlknur Erol

The abstract highlights that hearing loss is an occupational disease caused by noise exposure in the workplace. The study investigates noise-induced hearing loss among miners in underground coal mines in Turkey, considering factors like occupation, age, and exposure time. The research employs logistic regression analysis to reveal the relationship between hearing loss and these factors. The findings suggest that occupational groups and duration of noise exposure significantly affect hearing loss. Miners in production groups and those exposed to noise for 10-14 years have a higher risk. The study concludes that age does not significantly increase the probability of hearing loss.

Mar 24, 2022

By G. T. Lineberry

There is a critical need for effective instructional materials at the university level and for an upgrading of mine safety and health in the mining engineering curriculum. A fundamental approach to mine safety and health is recast into the familiar 3 E's: engineering, education, and enforcement, in that order. Each is briefly reviewed and their interdependence emphasized. A unique philosophy for successfully integrating safety and health principles into the mining engineering curriculum is offered. The concept of textbook ?tailoring? is discussed and defended, permitting rapid assemblage and synthesis of existing educational materials. Final recommendations are made for a u, comprehensive approach to mine safety and health education in the undergraduate curriculum.

Jan 1, 1987

By S. T. Hall

The authors have previously described a method of enhancing the magnetic susceptibility of pyrite by a mild alkaline oxidative pressure leach (Hall et al, 1985). This finding was successfully applied to enhance the magnetic desulfurization of an Eastern Canadian coal (Hall and Finch, 1984). This paper reports on enhancement of the magnetic susceptibilities of iron-containing sulfides (arsenopyrite, chalcopyrite and marcasite) upon similar treatment. It also explores the application of this pretreatment in the magnetic separation of fine sulfides from oxides and other sulfide minerals. In the latter case galvanic interference effects have a serious impact on the potential use of this method.

Jan 1, 1985

By Georgene Renner

Due to disturbance of their traditional roosts, caves and tree hollows, more than half of the 44 bat species found in the United States and Canada now live in abandoned and inactive underground mines. The North American Bats and Mines Project was created two years ago by Bat Conservation International Inc. (BCI) in Austin, TX and the Bureau of Land Management (BLM) in response to the issue of mine closure and bat habitat. The partnership provides national coordination among government and private agencies and the mining industry to minimize the loss of bats living in mines. It also trains land managers on how to conduct cost-effective mine assessment and closure to protect both bats and people.

Jan 1, 1996

By William R. Yernberg

Caterpillar introduced 21 new products during Caterpillar Press Days ‘96, held in June at the company’s proving grounds near Tucson, AZ. The event, billed as the largest product introduction ever held by Caterpillar, was attended by press from around the world. Most of the new products were demonstrated at Caterpillar’s Tinaja Hills Training Center in the Sierrita Mountains south of Tucson. Under the scorching Sonora Desert sun, the press was treated to demonstrations of the new equipment. After a display of the equipment’s power and capabilities, the press was given an opportunity to operate the new models and, in some cases, compare them with the old.

Jan 1, 1996

Zirconium chloride is of great commercial importance as starting materials for production of ZrO2, Zirconium metal and other Zirconium compounds from its main resources (Zircon Sands). The present study concerns with preparation of pure ZrO2 from Zircon by direct chlorination technique. Different parameters affecting the chlorination process are studied viz. carbon, chlorine flow rate temperature and time. The chlorination extent is determined from the loss in weight and chemical analysis of reaction products. The maximum chlorination extent -92% are achieved at 1100°C for 30 min. Zirconium oxide is produced from the collected zirconium tetrachloride either by calcination at 900°C or by hydrolysis in water in presence of RCI with a purity = 99%. Evaluations of the products of the process are investigated microscopically and by X-ray diffraction. The apparent activation energy of the chlorination of Zircon is determined to equal 36 kJ/mole.

Jan 1, 1997

By G. F. Ayakwah

Point load strength (Is50) and slake durability (ID2) indices provide a measure of the strength and durability of rock fragments and are related to the alteration intensity and frictional resistance of the materials. Samples were collected from the rock piles, alteration scars and debris flows at the Questa mine with the purpose of examining relationships between Is50 and ID2, mineralogy, chemistry, weathering, hydrothermal alteration, and other geotechnical parameters. The Is50 from the various rock piles ranges from 0.6-8.2 MPa and the ID2 ranges from 80.9-99.5%. The Is50 and ID2 results indicate that the samples from the debris flows are stronger (average Is50= 4.0 MPa and ID2= 98.4%) than the rock-pile samples and that the alteration scar samples are weaker (average Is50 = 2.8 MPa and ID2 = 89.2%) than the rock-pile samples, but still most of these rocks are strong in terms of their Is50 and ID2. The Is50 decreases as the degree of alteration increases in some rock pile and alteration scar samples, but not in all. However, the majority of the rock fragments within the rock piles still indicate high strength, even after 25-40 years of weathering.

Jan 1, 2009

By P. Mendoza, R. Siwale, H. Amini, R. Silva, M. Richards, V. Ngcoza, D. Rivera, C. Canaza, R. van Reenen

Development of a realistic flotation model to predict its performance is of paramount importance to the processing plant and operators, a model that accounts for predictive and no-predictive maintenance simulating individual equipment downtime and the effect of it in the metallurgical performance on the flotation bank with final recoveries and grades has a huge advantage on optimizing the flotation circuit/bank in terms of mechanical and metallurgical side. The Model was developed in a dynamic environment that allows for a better and more realistic simulation of the flotation bank. The maintenance model accounts for the Failure rate, Mean Time Between Failures (MTBF), Mean Time to Failure (MTTF) and Reliability (R(t)) those characteristics are combined to a multi-compartment process model that consists of a slurry recovery model, two options of froth recovery models, entrainment and carry capacity as a final check for the system. In addition to the maintenance and process model, a dynamic dart valve model was added to the simulation in order to have a realistic model to control the slurry level at the flotation cell. The paper goes over a study case for a current flotation operation trying to explore all the elements and the simulator to optimize the Rougher flotation bank.

Mar 2, 2022

By R. A. Jankowski

Although the number of operating longwall mining systems has remained relatively consistent over the past five years, longwall production levels have increased significantly during this period. Longwall production currently accounts for approximately 50% of U.S. underground coal production. While longwalls are highly productive and offer other advantages, operations employing this method of mining continue to experience dust compliance problems. This increased longwall productivity has meant that far more dust is being produced. An improved understanding of the longwall face ventilation system and advancement of face ventilation technologies are necessary to ensure all face personnel are allowed to work in an environment that is free of excessive levels of airborne respirable coal mine dust. The Dust and Toxic Substances Control Branch of the National Institute for Occupational Safety and Health's Pittsburgh Research Laboratory has examined several basic principles of the longwall face ventilation system, and has evaluated the effectiveness of numerous improved face ventilation techniques for longwall mining systems. These include identifying improved techniques for measuring face ventilation parameters on longwall mining sections and investigating the fundamental relationship between face air flow and the entrainment and dilution of respirable coal mine dust. Studies have been completed to determine the impact on face dust levels from using belt entry air to ventilate the longwall. Novel methods have been identified to increase the amount of face air flow and to manage face air flow to most effectively minimize face workers' dust exposure. Unique systems of auxiliary face ventilation have been developed and evaluated at full-scale, simulated longwall test facilities. The theoretical and applied aspects of each of these principles and technologies are discussed. Application of these results, throughout the longwall mining industry, as documented from surveys conducted in the early 1980's and 1990's, have reduced the health hazard associated with excessive exposure to respirable coal mine dust.

Jan 1, 1998

Laboratory tests were conducted to evaluate the silica collection efficiency of flooded-bed scrubbers with six different filter panel designs and at two operating velocities. Test results indicated that reductions in filter density negatively impacted respirable dust collection. Silica collection efficiency for the least dense filter was as much as 33 % lower than the collection efficiency of the densest filter. At the low operating velocity, the least dense filter allowed over 40% of the respirable silica dust in the scrubber intake air to pass through the unit, where it would be discharged back into the mine environment. Operation of the scrubber at the higher test air velocity increased silica collection efficiency, regardless of the filter panel tested. The density of the filter panels also impacted the quantity of air that is moved through the scrubber, with higher density filters reducing scrubber airflow. For each filter, the relationship between dust collection efficiency and air moving capacity must be considered to determine overall effectiveness for specific mine applications.

Jan 1, 1998

By Jerry G. Rose

This paper addresses a process by which both the disposal and utilization of preparation plant coal refuse can be simultaneously accomplished with an attendant benefit of significantly increasing the percentage of extractable coal. A laboratory study is described in which coal refuse was successfully utilized as an aggregate in low cost concrete (coal-crete) mixes under simulated mine environments. Coal-crete specimens with compressive strengths of 14,000 kPa (2,000 psi) were consistently produced. A construction sequence and mining plans are offered for placing the low-cost coal-crete pillars in accessible areas in room-and-pillar mines so that a Substantial portion of the remaining coal pillars could be extracted. The method could be applicable in areas where mining procedures do not permit pillar extraction because of possible surface subsidence, roof problems, or other conditions. Possible structural difficulties with the coal-crete pillar support system are discussed. Using a discounted cash flow analysis, the economic feasibility of mining with the coal-crete pillar system is investigated. The cost of the coal-crete pillar system is compared to the cost of a mining system which would have less coal recovery. The analysis indicates that although at higher coal selling prices the coal-crete mining system may yield an acceptable rate of return, the alternative of leaving the coal pillars is more attractive at the present time.

Jan 1, 1977

By Walenty Frydel

The paper deals with highly efficient dust collecting systems of the 10-600 type which constitute new generation installations de- signed to eliminate dust hazard in headings driven with roadheaders. A vortex ventube controlling the air flow in the com- bined ventilation system by means of air vortex generated by the ventube drive unit is also presented. From the results of measurements of under-roof concentrations of methane it appears that the application of the vortex ventube makes it possible to decrease the under-roof accumulation of methane more than 10 times.

Jan 1, 1997

By Daniel B. Brimhall

The research presented here was initiated to investigate the role of atmospheric oxygen in the leaching of copper waste dumps. The problem of increasing the recovery rate of copper from these dumps is or great importance considering there are by conservative estimate in excess of fifteen billion pounds of copper located in dumps in the western United States. At this time, there is an increased interest in recovering copper from these dumps on a large scale. Large tonnages of low-grade material are being placed on the waste dumps of most copper mining operations in the western United States each day. The size of these dumps ranges from 5.5 million tons at Mineral Park, Arizona, to 4 billion tons at Kennecott's Utah operation (1). Leach solutions are recycled and contain ferrous and ferric sulfates. Large quantities of dissolved aluminum, magnesium and calcium salts may also be present. To this solution make up water is added to maintain the solution inventory and sulfuric acid is added for pH adjustment. Iron is introduced into the leach solution by the dissolution of the iron-containing sulfide and oxidized minerals present in the ore deposit. In addition to the iron from dump leaching, iron is also introduced during the precipitation process when the pregnant solution is passed over metallic scrap iron if cementation is used to reduce the copper in solution.

Jan 1, 1972

By H. E. Rudi

The advent of open nit mining permitted the development and processing of minerals never before thought possible. New equipment was needed; new techniques were devised; new methods were called for. This development and acquisition of new techniques, methods and equipment did not, however, stir the souls of our industry and educational leaders sufficiently to a recognition of the problem of people, especially the future development of the people needed in open-pit mining. The people problem has been and will be with us as long as there are two of them. The development of people will be required for the same reason. The problem of developing future personnel for open-pit mining is not what must be developed; that is known to all of us and can be briefly stated ashore and better of everything." As I see it, the real problem lies in determining (1) what personnel are really critical, (2) why are they critical and (3) how can we develop them.

Jan 1, 1965

By D. A. Elgillani

Oxidation potentials have been measured in the presence of various concentrations of cyanide, ferrocyanide, and ferricyanide and ethyl xanthate at various values of pH and related to flotation response. Eh-pH diagrams are constructed and show that the formation of surface ferric ferrocyanide is probably responsible for depression when cyanide is added. The influence of cyanide in the depression of pyrite with xanthates as collector has been the subject of many investigations (1,2,3,4,5,6), and from these studies several theories on the mechanism of depression have evolved. Wark and Cox (7) and Gaudin(8) have suggested that the depressing effect is due to a competition of cyanide ion with xanthate ion for the surface. Cook and his colleagues (9,10,11) have explained this phenomenon in terms of competition between hydrocyanic acid and xanthic acid. Sutherland (12) has shown that both of these theories describe accurately the relation between pH value and cyanide addition at constant collector addition but fail to describe the relationship, between pH value and the amount of collector required to cause flotation. Taggart(12) suggested that depression in these systems is due to the formation of a reaction product between ferric ion at the pyrite surface and ferrocyanide ion derived from solution. Majumdar(4,6) has attempted to prove this hypothesis by measuring the contact angles of pyrite in the presence of 25 mg/liter ethyl xanthate and different concentrations of potassium ferrocyanide and ferricyanide. In all cases the contact angles were quite high up to pH 10; these results indicate that pyrite should not be depressed by either potassium ferrocyanide or ferricyanide. In view of these facts, Majumdar has assumed that the compound Fe(CN)2 forms at the surface.

Jan 1, 1968

By R. M. Quinlan

The coal industry in the United States has undergone significant economic changes during the past six years. The price of coal remained relatively constant from 1950 to 1969 (See Figures 1 and 2). Steam coal prices tripled and metallurgical coal prices doubled from 1969 to 1974. This price structure has created a new economic environment for coal preparation. Contributing factors to these price trends include: ? Coal Mine Health and Safety Act of 1969 ? Mid-East oil embargo of 1973 ? United Mine Workers of America contract agreements ? Productivity decrease (tons per man-day basis) ? Environmental Protection Agency regulations The increased value of coal justifies additional capital investment in cleaning facilities to optimize yield. Current trends include recovery of existing slurry ponds and recleaning of refuse. Coal preparation plant product yield and quality must be evaluated in terms of the amount of capital expended and cost of operation. Therefore, it is advantageous to optimize the plant product based on clean coal selling price and rate of return on investment.

Jan 1, 1976

By K. Fair

Using an agitated column 203 mm (8") diameter by 1829 mm (72") tall with independent agitation units for the gas dispersion zone and the collection zones, respectively, permitted the independent evaluation of the attachment and the detachment mechanisms for the chalcopyrite/ silica system. Three particle size fractions were used in this study, i.e. coarse (+75 µ m), intermediate (-75 µ m + 10 µ m) and fines (-10 µ m). The optimum selection of the two agitation zones for the three particle size fractions were determined as a function of grade, recovery, residence time and air superficial gas velocity.

Jan 1, 1990

By Irina Melekestseva, Beltenev. Victor, Victor Ivanov

"One of the major problems discussed over the last years is a possibility of mining of seafloor massive sulfide deposits. In spite of the pessimistic points of view on their commercial development, they are still of great interest and continue to be studied (Hannington et al., 2011). Recently, Barriga (2012) paid special attention to the underestimated amount of massive sulfide hydrothermal fields and pointed to the importance of the buried fields and subseafloor mineralization.This study examines the geochemistry of seafloor and subseafloor precipitates collected at the Peterburgskoe (19°52´ N) and Irinovskoe (13°20´ N) hydrothermal fields (MAR) during the 34th cruise of the R/V Professor Logatchev in 2011. These fields were discovered by the Polar Marine Geosurvey Expedition in 2010 and 2011, respectively (Shilov et al., 2011; Beltenev et al., 2012). The Peterburgskoe field, associated with basalts, is located 16 km west of the main rift valley at the depth of 2800-3100 m at the junction of a large non-transform discontinuity with the second rift ridge parallel to the rift valley. The Irinovskoe field occurs at depths of 2700-2850 m and has a northwestern satellite sulfide site, both confined to an oceanic core complex (MacLeod et al., 2009), which includes mafic and ultramafic rocks. The details of geological structure of the fields may be found in the relevant papers.Diverse samples were collected from the hydrothermal fields: seafloor massive sulfides, Fe-hydroxide crusts, SiO2-rich sulfide-bearing precipitates, and subseafloor mineralized rocks (Melekestseva et al., 2014a). Massive sulfides may be subdivided on the Fe-rich and Cu-rich types. The marcasite-pyrite, pyrite, hydroxide-marcasite, and chalcopyrite-pyrite (Fe-rich) mineral types are dominant in the Peterburgskoe field at lesser amounts of sphalerite-hydroxide-chalcopyrite and pyrite-covellite-chalcopyrite (Cu-rich) massive sulfides. The mineralized sulfide-talc-carbonate-chlorite, chlorite-sulfide-quartz, and hematite-sulfide-quartz rocks host stringer-disseminated sulfides including chalcopyrite, covellite, and pyrite."

Sep 1, 2014

By J. J. Reilly

The Vesta Mines of the Jones & Laughlin Steel Corporation operate in the Pittsburgh Seam in Washington County, Pennsylvania. This seam is overlain with a drawslate, 12" to 16" in thickness, which slimes readily when wet. Because of the need for a uniformly good quality metallurgical coal, the amount of reject, together with the top and particle sizes of the raw coal feed, is a serious problem at the Vesta Preparation Plant. The Preparation Plant operates two, seven and one-quarter hour shifts per day and processes 2,100 tons per hour of raw coal feed. The third shift is, used for planned maintenance of equipment. Since the water clarification equipment is so vital in insuring a uniform product, there is no alternative but that it be in operation at all times. To insure this continuous operation,. well-planned maintenance is a necessity. For years, Plant Management has kept performance records of the various units to determine the renewal dates of vital component parts, the length of wear, the various materials used in the manufacture of the equipment, and the labor cost for renewal. These records have been of inestimable help in planning an effective maintenance program to insure continuous operation of the various units.

Jan 1, 1959