Search Documents

By D. G. Chedgy

This article presents a novel design, called the Climax High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 -660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Jan 1, 1997

By Young C. Kim

Use of geostatistics to solve mining problems is gaining importance as the cost of developing new mines is increasing and there is a need to mine more marginal deposits. But, until recently, coal companies have shown little or no interest in geostatistics. However, the stringent quality controls on coal burning has led to a surge in interest in improved methods for estimating clean coal characteristics. Until now, most of the geostatistical applications have centered on the problems of estimating in-situ coal characteristics (Sabourin, 1975; Wood, 1976, 1979; Fang and Stark, 1976; Pauncz and Nixon, 1979; and Knudsen et al., 1980). Little work has been done in applying geostatistics to coal washability, except that by Armstrong (1980). Applying geostatistics to coal washability basically means the estimation of cleaned coal characteristics, with the aid of geostatistics. Cleaned coal estimation plays a very important role in overall emission control strategy, as can be seen by the general flow diagram of such a strategy shown in Figure 1. The scope of this paper is limited to one aspect of the overall emission control strategy shown in Figure 1; namely, the prediction of cleaned coal characteristics using geostatistics.

Jan 1, 1982

By F. Calizaya

This study summarizes the results of various numerical and laboratory experiments per-formed to study the effect of airflow recirculation on gas concentration. The numerical exercises were carried out on a simulated mine ventilation net-work. The laboratory experiments were conducted at the Mackay School of Mines' airflow monitoring system in Reno, Nevada. In both cases, the airflow was recirculated through the system by means of a main fan and a set of booster fans. The booster fans were positioned to produce two types of recirculation: In line and Cross-cut. For each type, various recirculation conditions were generated by changing the booster fan pressure. During each test, the gas emission rate at the simulated working face was kept constant. The study illustrates the conditions under which controlled airflow recirculation may be used to solve a district ventilation problem.

Jan 1, 1991

By F. Woller

The territory of Czechoslovakia is well endowed in deposits of a variety of industrial minerals. At present, 29 different types of industrial minerals are mined from some 600 individual deposits in Bohemia and Moravia only. About half of those production centres involves structural materials like aggregate and common brick clays and loams. A significant proportion of industrial minerals produced in Czechoslovakia are exported. Destinations of main products are shown in Figure 1. Production of industrial minerals in Czechoslovakia has a long history. Glass has been produced since the 14th century, sulphuric acid since 1578, graphite since 1750, and chinaware since 1790, to name just a few; but most of the present production comes from deposits developed during the past forty years. For a variety of reasons, only about 30 per cent of registered and explored industrial minerals deposits in the country are in production (Table 1). Two of the reasons may be the complexity of processing or conflicting interests of parties involved, but lack of market research, investment funds, or processing capacity have also had an impact on the level of utilization of the resource base.

Jan 1, 1992

By Edwin B. Wilson

Electric power generation remains the greatest market for coal in the United States. In 1967, about 272 million tons of coal, amounting to over 51 percent of total coal consumption, were burned to satisfy this nation's hugh demand for power. The size of the utility market is currently five times that of 1941 and continues to grow with the demand for more and more energy. A major reason for this strong market has been the ability of the coal industry to supply a superior product for combustion while maintaining competitive prices. Now that the coal industry is engaged in intensive competition with nuclear power for future energy demand, it becomes ever more imperative that superior coal products are produced. One important problem when burning some coals is a liquid phase corrosive attack on boiler tube metal in the superheater and reheater areas of the furnace where steam temperatures may exceed 1050°F.

Jan 1, 1969

By E. T. Tuzcu

Microscale information about single particle fracture can be incorporated into the macroscale model of the whole size reduction process in the mill. The ultrafast load cell (UFLC) device provides a substantial amount of information about fracture characteristics of a particle under impact loading. UFLC captures high-resolution compressive force signals during particle breakage. The measurement of the compressive force at the instant of fracture of the particle allows computation of a number of comminution-related particle properties, as well as the energy absorbed during fracture. In the current study, limestone particles 50 mm in size were fractured to obtain specific fracture energies. Then, based on the experimental data, two models were proposed to quantify the fracture process. The specific fracture energy distribution of the particles in the range of 6 to 50 mm was defined by the well-known Weibull distribution. The other model is a probabilistic fracture model. This model is a link between energy events occurring in a grinding mill and the breakage rates of particles. The impact energy spectra or energy events occurring in a grinding mill can be obtained with a discrete element method (DEM) simulation. One can model the breakage rates of the mill material by combining the energy spectra with the probabilistic fracture model. This novel approach for the modeling of breakage rates via DEM and UFLC is shown here.

Jan 1, 2011

By E. T. Tuzcu

Microscale information about single particle fracture can be incorporated into the macroscale model of the whole size reduction process in the mill. The ultrafast load cell (UFLC) device provides a substantial amount of information about fracture characteristics of a particle under impact loading. UFLC captures high-resolution compressive force signals during particle breakage. The measurement of the compressive force at the instant of fracture of the particle allows computation of a number of comminution-related particle properties, as well as the energy absorbed during fracture. In the current study, limestone particles 50 mm in size were fractured to obtain specific fracture energies. Then, based on the experimental data, two models were proposed to quantify the fracture process. The specific fracture energy distribution of the particles in the range of 6 to 50 mm was defined by the well-known Weibull distribution. The other model is a probabilistic fracture model. This model is a link between energy events occurring in a grinding mill and the breakage rates of particles. The impact energy spectra or energy events occurring in a grinding mill can be obtained with a discrete element method (DEM) simulation. One can model the breakage rates of the mill material by combining the energy spectra with the probabilistic fracture model. This novel approach for the modeling of breakage rates via DEM and UFLC is shown here.

Nov 1, 2011

By Robert R. Unterberger

The purpose of this paper is to summarize the research of the past sixteen years on three distinct methods of probing into solid rock. The first method is to use radar of the appropriate frequency. The second method is to use sonar. The third method is of recent vintage and uses techniques of nonlinear sonar also known as parametric sonar. The first two concepts, that of radar and sonar, are common to most people. Very few have heard of nonlinear sonar. Each of the probing techniques were investigated in order to overcome deficiencies in the former technique. Each has its advantages and disadvantages. It should be emphasized that all of these techniques for probing (or seeing) into rock are used in mines, and generally speaking not from the surface. Only in very special cases, such as certain very dry parts of Egypt or Peru, or, for example, the surface of the moon, will these probing techniques work from the surface. The reason for the development of these probing techniques has been to alert miners to possible hazards ahead of mining. Such hazards may be (1) old (unknown) boreholes connected with high pressure water zones above, (2) fractures that might connect to the Gulf of Mexico above the mine, (3) water-filled fractures that threaten the safety of miners, or (4) the discovery of dry faults ahead that can disrupt the planning of future operations.

Jan 1, 1983

By V. H. Forsythe

Mr. Chairman, members of SME, and guests It is indeed a pleasure to have the opportunity to appear before this group. The topic of this paper is, "Current Trends in Related Industries and Their Influence on Electric Shovel Design and Size". Before getting into the major items, it is well to point out that this text will deal with loading shovels primarily, since their application is almost universal in major open pit mining operations throughout the world. Related industries influence our design in many ways. For the sake of simplicity, these industries will be broken down into two major categories. The first category to be discussed will include industries that will indirectly influence design and size, while the second category will include industries whose products can directly be incorporated by the engineer in the design of shovels.

Jan 1, 1964

By Martin C. Kuhn

The use of tritium in manufacturing and its subsequent loss to the local environment in Tucson, Arizona resulted in a great debate relative to the physiological effects of low level radiation. This paper reviews some of the facts of the release and attempts to quantify the degree of hazard encountered by the local community. Some of the difficulties in assessing the true degree of absorbed dose and the assumptions necessary for calculation purposes are presented.

Jan 1, 1981

By S. S. Peng

Since the introduction of shield supports in 1975, safety and production in U.S. longwall faces have improved considerably. Many faces had a daily production of up to 8,000-10,000 tons and productivity reached 600 tons per man-shift. But a longwall face requires expensive equipment which slows down the growth rate of the percentage of longwall production. Among the equipment cost the shield support accounts for 50-60%, a very large proportion. Therefore, it will have a large impact on the growth of longwall mining in the U.S. to reduce the support cost (1).

Jan 1, 1988

By Andrew Cushing, Joe Carvalho, Jon Hurt

"INTRODUCTIONThe shales of the Greater Toronto Area (GTA) have been known to experience time-dependent deformations (TDD); those initiated by excavation-induced stress relief which progress with time as a function of rock porewater salinity, access to freshwater (or air) of lower salinity, clay and calcite content, and the buildup of swelling pressures within the rock mass. These deformations can induce long-term pressures on shaft walls and tunnel linings, especially if the permanent works are constructed soon after excavation, with very little time delay. This paper presents measurements of time dependent deformation of recent shaft and tunnel projects constructed in the GTA, and draws conclusions regarding the main influences on the TDD. The key input parameters for the numerical predictive model are critically assessed. Projects which are discussed include the Billy Bishop Airport Pedestrian Tunnel, Hydro One Midtown Tunnel and Hanlan Feedermain (Contract 3).MECHANISM OF TIME DEPENDENT DEFORMATIONExplanation of MechanismThe Georgian Bay Shale unit consists of typically moderately weathered to fresh, grey to dark grey, fine to very fine grained fissile shale interbedded with slightly weathered to fresh grey, fine grained calcareous siltstone and limestone interbeds. There are two distinctive features of the shale in the Greater Toronto Area (GTA). One is a high horizontal stress regime, and the second is long-term time dependent swelling behavior which develops when the following factors occur (Lo and Micic, 2010):• Stress relief of the rock mass• Outward salt concentration gradient from pore fluid of the rock to the ambient fluid• Availability of fresh waterThe swelling is a consequence of the reduction in confined stress in the rock which occurs upon excavation in combination with a differential gradient in salinity between the saline rock porewater and freshwater or even humid air. Osmotic and diffusive processes result in a decrease in the salinity of the rock porewater achieved by an overall increase in the water content, resulting in volumetric expansion of the shale rock over time. The development of this time dependent deformation (TDD) relative to the time"

Jan 1, 2016

By Alfred L. Anderson

Thorite and rare earth deposits in the Lemhi Pass area of southeastern Lemhi County, Idaho, are contained along complex shear and fracture zones and in reopened gold-quartz veins and copper lodes in quartzitic and phyllitic rocks of the Pre-cambrian belt series. Some of the shear and fracture zones are several tons of feet across and comprise broad zones of irregularly mineralized rock. These lodes contain a notable concentration of thorium and rare earth elements along with considerable amounts of barium, .potassium, calcium, iron, aluminum, phosphorus, sulfur, and silicon. The principal minerals are thorite, locally allanite, monazite, xenotime (?), apatite, specular hematite, barite, potash feldspar, occasionally calcite and quartz. Exept for some of 'the specular hematite, barite, reddish feldspar, calcite and quartz, the minerals are not distinguishable without the microscope. The thorite and locally allanite were deposited first, then the monazite and other phosphates, which were in turn followed successively by barite, potash, feldspar, calcite, and quartz. In exceptional cases, deposition of thorite and specular hematite was repeated after the feldspar. Some of the deposits contain several percent thoria, but the average os generally under one percent. The rare earth content is comparable with that of the thoria. The deposits appear to be of hydrothermal origin and are probably related genetically to late Cretaceous or early Tertiary igneous activity, manifested locally by a few dioritie and lamprophyric dikes.

Jan 1, 1959

By E. W. Davis

This paper deals with the role of the Maintenance Department in a milling operation; specifically, the Mines Development, Inc., processing plant at Edgement, South Dakota. The goal of very maintenance department is the smooth and uninterrupted operation of the plant it serves, To achieve this goal, maintenance men adapt various features and procedures into a program designed to fit the characteristics of their particular plant operation. A few of the basic elements of a sound maintenance program are: 1, A periodic preventive maintenance schedule. 2, A systematic inspection and lubrication procedure. 3. A training program for maintenance personnel. 4 A good equipment-history file system, 5. A carefully planned spare parts inventory.

Jan 1, 1962

By William J. Miles

The inhalation of dust has been a problem in the mining industry since antiquity. Crystalline silica is now known to be the cause of silicosis, a form of pneumoconiosis that is associated with excessive exposure to respirable particles in some mining and industrial environments. Crystalline silica was reviewed by the International Agency for Research on Cancer (IARC) in 1986 and classified as a Group 2A, Probably Carcinogenic to Humans in Volume 42 and Supplement 7 of the IARC Monographs (1987). In 1996, IARC reviewed additional literature and studies published in the intervening decade and recommended that quartz and cristobalite, two polymorphs of crystalline silica, be listed as Group 1, Carcinogenic to Humans. Their recommendations and reclassification were published in 1997 in IARC Monographs 68.[2] In both Monographs, IARC classified amorphous silicas as Group 3, Inadequate Evidence for Carcinogenicity to Humans.

Jan 1, 1998

By J. Noll, D. Yantek, J. Organiscak

The Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) conducted laboratory testing of a self-tramming, remotely controlled mobile Dry Scrubber (DS) that J.H. Fletcher and Co. developed under a contract with NIOSH OMSHR to reduce the exposure of miners to airborne dust. The scrubber was found to average greater than 95 percent dust removal efficiency with disposable filters, and 88 and 90 percent, respectively, with optional washable filters in their prewash and post-wash test conditions. Although the washable filters can be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-min washing period. The scrubber’s velocity-pressure-regulated variablefrequency- drive fan maintained relatively consistent airflow near the targeted 1.42 and 4.25 m3/s (3,000 and 9,000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60-Hz fan motor frequency or horsepower rating at 2,610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8,420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the scrubber showed that the outlet side of the scrubber was noisier, and the loaded filters increased sound levels compared with clean filters at the same airflow quantities. With loaded filters, the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6,000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level — under Title 30 Code of Federal Regulations Part 62.101— of 90 dB(A) at or below this airflow quantity. The scrubber’s washable filters were not used during field-testing because of their lower respirable dust removal efficiency and the airborne dust generated by filter washing. Field-testing the scrubber with disposable filters at two underground coal mine sections showed that it could clean a portion of the section return air and provide dust reduction of about 50 percent at the face area downstream of the continuous-miner operation.

Jan 1, 2016

By R. R. Klimpel

The industrial processing of ores containing precious metals such as gold is generally very mining site specific, e. g. McQuiston and Shoemaker (1985), vanZyl et. a1. (1988), Fuerstenau and Hendrix (1990), and Hausen et. a1. (1990). The variety of various mineral processing techniques employed is extensive and includes size reduction, size classification, gravity separation, roasting, cyanidation, chemical and/or bacterial leaching, ion exchange and/or solvent extraction, and froth flotation. Gold occurs in the earth's crust on the average in very low concentration estimated by various sources to be between two and five parts per billion. For a specific ore deposit to be considered as an economic source of gold, generally a concentration of near one part-per million (one gram / Mton) or more is required. From a mineralogical viewpoint, gold often occurs in its native or free form. However, it can also occur as gold compounds of telluride, antimony, and selenium contained within either sulfide minerals such as pyrite, arsenopyrite. and pyrrhotite or, to a less extent, within silicate, oxide, and carbonate minerals. In many locations, alloying of gold with silver is found. The optimal processing method for recovering gold is determined by many factors such as the mineralogy of the gold bearing minerals as well as the associated mineralogy of the gangue minerals, the type of liberation profile of the gold bearing minerals upon' size reduction, and the particle size of the gold itself. Free or native gold particles can vary in size from the extreme of large nuggets to very finely disseminated gold associated in a complex sulfide mineral matrix. Typically free gold particles of several hundred microns or larger are efficiently recovered by one or more of a number of gravity based techniques due to the large specific gravity differential of gold (19.3 to 15) versus typical gangue minerals (5 to 2.7). When gold is associated with a sulfide (usually pyrite) matrix, historically most industrial plants involving size reduction and subsequent liberation have operated in a size range of 50 to 80 percent less than 75 microns. Grinding finer than this has been normally not economical unless the ore has a high gold content in the feed ore.

Jan 1, 1998

Laboratory testing by the Federal Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores which have a high content of water-insoluble impurities. Results indicated that up to 85 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered up to 88 percent of the potash in rougher concentrates containing 47 to 57 percent K20. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K20. Filtration of the insoluble slimes flotation concentrates recovered 87 to 0 percent of the brine. Flotation concentrate filtration rates were 7 times faster than the filtration rates of mechanically deslimed products.

Jan 1, 1977

By A. A. Campoli

The U. S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

By L. K. Holder

The White King / Lucky Lass Superfund site consists of two former uranium mines in south-central Oregon. The remedy included consolidating two large mining overburden stockpiles that contained low levels of radioactivity and heavy metals by moving over 700,000 cubic yards of material and then capping the combined stockpile. An innovative armored cap design was used to minimize the stockpile footprint and thereby prevent disturbing existing wetlands. In addition, the stockpile was designed to merge into the surrounding topography. The remedy also included stream restoration and development of new wetlands. The stream was returned to its pre-mining channel, with the addition of hydraulic features to create new wetlands. The wetlands have greatly enhanced the ecological value of the remedy and the site.

Feb 23, 2014