Search Documents

By Bruce D. McCellan

INTRODUCTION The gathering arm loader was patented by Joseph Joy in 1916. This unique machine motion became the standard of the industry and is used on underground loaders and continuous miners throughout the world. Figs. 1 and 2 show two types of gathering arm loaders. The gathering arm loader is a crawler-mounted ma¬chine primarily used for loading coal in a conventional mining system. Other uses also have been found for this machine in noncoal mines and other industries. MECHANICAL ASSEMBLIES The front or loading end of the machine, commonly called the head, consists of a tapered structural frame, hinged at the rear to the chassis and riding the ground at the front. Two bevel-gear cases are mounted in the head. They are connected by a timing shaft, which also acts as a conveyor drive shaft on most models. An eccentric disk attached to each gear case drives the gathering arms. The rear of the arms are attached to a swivel assembly. The motion derived from this arrange¬ment gathers loose material from the ground directly in front of the machine and loads it into the conveyor. Power for this drive is provided by two electric motors mounted under the gathering head. A speed reducer attached to each motor provides a gathering arm speed of approximately 5.2 rad/s (50 rpm). A torque limiting clutch is provided on each reducer to guard the system against sudden impact loading and continual overloading of the motors. The conveyor consists of an open box section through which a universal-type chain carries the ma¬terial to the rear of the machine, where it is discharged into the haulage vehicle. The chain is driven by a sprocket located on the timing shaft between the two gathering-head bevel-gear cases. On some large loader designs, primarily for noncoal applications, the chain is driven by a separate gear motor at the discharge end of the conveyor. However, the system driven by the timing shaft is used most widely. The conveyor frame is hinged just to the rear of the gathering head. It can be raised or lowered by hydraulic cylinders to the desired discharge height. The conveyor frame also is designed to pivot 0.79 rad (45°) either side of the center, just to the rear of the chassis. This feature increases the maneuverability of the ma¬chine and makes it possible to discharge material into the haulage system when in tight quarters such as when turning a crosscut. This function also is controlled by a hydraulic cylinder. The chassis of the loader consists of two crawler frames and cross members, holding the frames in position. The frames are either welded or cast as¬semblies. Replaceable wear runners are provided on the frames to take the wear generated by the crawler chain. An adjustable take-up idler keeps the crawler chain in proper adjustment for maximum life. The drive system for the crawler chains varies with the manufacturer, but it generally is one of two basic designs. One system provides a traction motor for each side of the machine, coupled to a speed reducer. A spur and bevel-gear train transfers power to the sprocket, which drives the crawler chain. Directional control is achieved by disk-type clutches. The other system also uses a motor for each crawler, coupled to a speed reducer. A roller chain drives the sprocket, which in

Jan 1, 1982

By R. W. M. Lai

The study of flotation kinetics was first reported by Garcia-Zuniga1 in 1935. Since then, literature on the subject has grown with the time. 2-19 Although there is an abundance of flotation kinet¬ics models available in the literature to describe flo¬tation systems, they are mostly of academic interest and are seldom applicable for use in the industrial environment. Several reasons contribute to the wide gap in the industrial -application of the academic models. These include: 1) the lack of generality in the model, e.g., the model is limited to certain size ranges; 14 2) the academic models involve complicated mathematics; 5,6,10,11 3) confusion about the order of the flo¬tation rate, e.g., several authors proposed a first order rate model, 1,15,16 whereas the others propagated a second order rate model: 2,17,18,194) the use of an unrealistic rigid value, such as the use of a maximum recovery of 100%, 5,8,19 which is unrealistic in industrial operations; and 5) the use of graphs that confuse the reader rather than interpret information. 2,3,10 This paper intends to introduce a simple and easy to understand empirical flotation kinetics model along with a way of presenting the model in an informative graphical form, which should stimulate the interest of other practical engineers to become concerned with practical application within the mineral industry.

Jan 1, 1982

By Charles H. Rice

Coal liquefaction processes can be divided into two broad classifications - direct and indirect. Direct liquefaction processes, in general, slurry coal with a solvent and react it with hydrogen under elevated temperature and pressure. Indirect liquefaction is the term applied to processes in which coal is first gasified to generate a synthesis gas of carbon monoxide and hydrogen. The synthesis gas is then converted to various types of liquid fuels by the proper selection of catalyst and conditions. The first experiments on direct coal liquefaction were undertaken in 1933 by Bergius. Development and commercialization of the Bergius concept was accomplished mainly through the effort of I.G. Farben at the Ludwigshafen plant of its subsidiary, Badische Anilin und Soda Fabrik A.G, under the leadership of M. Pier (1). A demonstration plat having an annual capacity of 100,000 tons of coal was built in Leuna, Saxony in 1927. Six years later, Imperial Chemicals Industries, Ltd., commissioned a plant in Billingham, England (2).

Jan 1, 1981

By P. R. Taylor

This work is concerned with the extraction of refractory metals using an electro-reduction process, in which a molten oxide melt, instead of halide, is used as the electrolyte. The process may provide an alternative method of producing refractory metals from their ores through use of a reverse-polarity direct current (DC) plasma arc heating process. In such a process, the plasma torch itself acts as an anode, and resulting liquid or solid product metals work as a cathode, whereas the molten oxide melt plays the role of an electron transfer layer. The focus of this study is: the electro-reduction of scheelite; vanadium pentoxide; and chromite. For the vanadium pentoxide, the proposed melt is mainly composed of CaO-V2O5/Li2O-B2O3-V2O5or FeO-CaO-SiO2-V2O5-Li2O with the addition of other alkali and alkaline metal oxides. In the case of scheelite ore, the SiO2-CaO-Li2O-WO3system is used as melt and metal aluminum or nickel could be used as a collecting media. As for the reduction of chromite ore, SiO2-CaO-Cr2O3-Li2O system with trace amount of CaF2is used as the melt. As a demonstration, chromium was successfully produced at a laboratory scale through the plasma driven electro-reduction process. One of the studied slags had a composition of 13.8% CaO; 4.9%CaF2; 36.4% Cr2O3; 6.9% Li2O; and 38.0% SiO2. Two observations are significant in this laboratory scale study. The first one was that the amount of Cr2O3and FeO, which were predominantly electronic conductors in the oxide melt, greatly affected the conducting mechanism of the melt. With high concentration of Cr2O3and FeO in the melt, the current efficiency was fairly low. In this case, chromium was found to be barely reduced because of electronic conducting mechanism. For example, with initial slag of 60% Cr2O3, no chromium was found reduced. With low concentration of Cr2O3and FeO in the studied melt, typically no more than 30% Cr2O3, it was observed that chromium was readily reduced due to the dominant ionic conducting mechanism. The second observation was that the addition of SiO2tothe melt helped to make the oxide melt more ionic, which was apparently desirable to the molten oxide electrolysis. However, high content of silica had a negative effect on the fluidity of the melt. This was resolved by adding trace amounts of CaF2to the melt. Therefore, by judicious selection of oxide melt, refractory metal oxides might be dissolved into it and yet the melt itself retains the required ionicity. A reverse-polarity DC plasma driven molten oxide electrolysis may prove to be a viable alternative route for the extractive metallurgy of refractory metals.

Jan 1, 2003

By MANZOOR ALI BROHI, IZHAR MITHAL JISKANI, Atta Ur Rehman, SHUAI HAN, MUHAMMAD TARIQ, NIAZ MUHAMMAD SHAHANI

The analysis of mine safety indicators using a scientific method can improve mine safety and assist management in making informed decisions. This research establishes a mine safety evaluation index and proposes an integrative evaluation model based on the entropy weight and grey clustering methods. The index consists of 27 indicators classified into seven criteria: working environment (A), miners’ attributes (B), safety policies and education (E), prevention and control (F), and monitoring and supervision system (G). Using Pakistan’s mine safety situation as a case study, the proposed model categorized the indicators into five safety levels (very low, low, medium, high, very high) for the present situation and for their relevance in terms of future safety improvement. The results show all of the criteria falling into the very low level for the current mine safety situation. Three of the criteria — C, E and G — are identified as having very high levels of significance for future safety improvements.

By V. Rastogi

Acid rock drainage is the result of exposure of sulfidic materials, such as pyrites and sulfidic ores, to air and water. The oxidation of these sulfides is catalyzed by more than a million times by the bacteria Thiobacillus jerrooxidans and close families. Inhibition of these bacteria can mitigate 98% or more of the acid loading generated. This can be achieved by the use of certain surfactants that are selectively bactericidal to the lithotropic acidophilic bacteria. Bactericides are used in two ways. As periodic or continuous treatments for prevention of acidification of material actively handled and moved, and in controlled release form for reclamation where treatment sets up a change in site microbiology to replace Thiobacillus jerrooxidans with heterotrophic bacteria and creates a stable site without need for further treatments. Use of bactericides begins with laboratory testing of the site material to qualify the site for bactericide treatment and dosage determination. Site specific treatments are designed for active sites and reclamation. Once acid production is controlled, solubilization of metals is correspondingly reduced. Results and economics of use from active and reclamation sites are presented.

Jan 1, 1995

By John R. Alderman

INTRODUCTION Uranium production in Saskatchewan commenced in 1953 at the Eldorado Nuclear Mine in the Beaverlodge area of North Saskatchewan, followed over the next few years by nineteen other smaller mining operations. Production rose from 453 600 to 2 721 600 kg per annum by 1958. Over supply and the closure of the U.S. market to Canadian uranium led to an equally rapid decline to an annual production which varied from 453 600 to 907 200 kg during the years 1964 to 1976. As the market strengthened there was a resurgence of the Saskatchewan industry and production from one underground and two open pit mines reached 2 809 000 kg in 1980 for a return of 232 000 000 dollars (Table 1). [ ] Future output will be increased by a potential 4 536 000 kg from the Key Lake mine now under construction and scheduled to commence production in 1983. Three other projects are in an advanced stage of planning and are currently in the regulatory review process. Several other prospects are being evaluated. Figure 1 shows the location of uranium mines in Saskatchewan and table 2 illustrates the present status of uranium mines and deposits in Saskatchewan. At present, 1400 workers are employed directly by the uranium mining industry. Saskatchewan has diverse mining conditions ranging from the underground mine of Eldorado Nuclear Limited 1870 m deep with a low grade ore deposit averaging from 0.17-0.20% with extraction by carbonate leaching through an open pit operated by Gulf Minerals with a moderate depth of 110 m and 0.37-0.5% grade to the shallow open pit of Cluff Mining 30 m deep with a very high average ore grade of 7.0%. Extraction at both open pits utilizes acid leach extraction processes, the latter after gravimetric separation. Key Lake mining has commenced development of the next mine to come into production which will have two open pits to a depth of 80 and 175 m with an average 3% grade to be followed by the deep open pit of Canada Wide Mines Ltd. to a depth of 205 m with average grade of 1.5%. One existing mine will transfer its operation from the present open pit to another of slightly higher average grade. From the Saskatchewan point of view, these different operating conditions present varied problems associated with occupational health and safety and concomitant solutions to reducing worker exposure to radiation. REGULATION OF URANIUM MINES In 1946, the Government of Canada enacted the Atomic Energy Control Act which established the Atomic Energy Control Board (AECB) and vested in that board powers to regulate all aspects of uranium mining. In the early years, the AECB relied heavily on provincial occupational health and safety agencies for the surveillance of uranium mining and milling operations, particularly with regard to "conventional" occupational health and safety, the AECB having at the time no specific regulations covering the mining industry. There has been considerable dialogue between federal and provincial governments since, traditionally, occupational health and safety is a provincial jurisdiction. Saskatchewan is strongly opposed to the intrusion of the federal government into the provincial domain, particularly as there is little justification for a federal presence in occupational health and safety in uranium mining and milling. The province does, however, accept the need for federal involvement in certain aspects of the regulation of nuclear industry, for example, international sales, research and security of reserves for domestic use.

Jan 1, 1981

By D. R. Buist

The Taharoa plant of New Zealand Steel Mining Limited extracts a 57% Fe titano-magnetite concentrate from a large mineral sand deposit 90 miles south of Auckland on the west coast of New Zealand's North Island. The plant consists of an 18-inch suction cutter dredge which feeds a 750 TPH floating separation plant. An initial gravity/ size separation is obtained using cone concentrators. Finished concentrate is produced by a combination of conventional drum magnetic separators and top fed wet Mortsell magnetic separators. Concentrate is stockpiled by cyclone, and reclaimed by a bull- dozer and tunnel system. Repulped concentrate is pumped by sub- marine pipeline to slurry tankers anchored at a single buoy one mile offshore. Current concentrate production rate is in excess of one million metric tons per year.

Jan 1, 1973

By John B. Draper

The 1980 Mine Dewatering Act was enacted to protect water rights and to allow mine dewatering to proceed where impairment of a water right might have otherwise created a bar to mine development. In New Mexico, new appropriations for beneficial use are subject to the State Engineer's jurisdiction and are granted only upon a showing of non-impairment. Before 1980, mine dewatering was not considered a beneficial use, nor was it considered waste. The Act brings mine dewatering under the jurisdiction of the State Engineer, makes it subject to the same requirements as an application for appropriation for beneficial use, grants the right to replace the water of users whose rights would be impaired by mine dewatering without a plan of replacement, and extends the right of replacement to non-mining appropriations of water for beneficial use, Application of the Act requires determination of the definition of impairment (the threshold of significant impact on existing water rights), hydrologic evaluations to determine the impact of the proposed dewatering, and preparation and execution of a plan of replacement to avoid impairment of existing rights.

Jan 1, 1983

By Daryl R. Tweeton

The Bureau of Mines has developed PC-based tomographic computer programs for geophysical applications, and is making them available to potential users as part of a Bureau plan to facilitate the transfer of technology to industry. These programs were initially developed for predicting and monitoring the flow pattern of leach solution during in situ mining. Seismic crosshole tomography has located fractured zones of low seismic velocity and saturated zones of high seismic velocit above the natural water table. The Bureau has applied tomography also to assessing high-wall blast damage, and examining the integrity of mine-related geological structures. The tomographic programs include the straight ray pro ram BOMTOM (Bureau of Mines Tomography? and the program BOMCRATR (Bureau of Mines Curved Ray Tomographic Reconstruction) that can be run with either curved or straight rays. Both programs provide optional mathematical constraints to help counteract the nonuniqueness of reconstructions that occurs with crosshole data. They are available from the Bureau free of charge. With typical data sets, they can be run on a 386 microcomputer with 640 Kb RAM. BOMTOM was described in the Bureau Report of Investigations 9159, so this report emphasizes BOMCRATR. Curved and straight ray reconstructions using seismic field data collected while simulating injection of leach solution were compared. The curved and straight ray tomograms were quite similar even with velocity variations of more than 50 percent.

Jan 1, 1992

By D. J. Brunner, S. Mathur, D. McKinney

With the advent of faster micro-processors, the use of numerical methods to simulate complex fluid dynamic phenomena in three dimensions for use in design has become prevalent in the automotive, and turbo-machinery industries. The Computational Fluid Dynamics (CFD) method divides the region of interest into small control volumes which form the mesh representing the physical characteristics of the problem, and uses the finite volume method to intergrate the equations for the conservation of mass, momentum, energy and species over each control volume. Recent developments in CFD software expedite mesh generation, and enable the use of unstructured grids, comprised of tetrahedral volumes in three dimensions and triangular areas in two. CFD more accurately represents complex geometries and allows for relative movement of meshes enabling simulation of multiple moving bodies. 'ibis paper presents two examples of how CFD simulation can be used to assess mine and tunnel ventilation problems formerly addressed by application of analytical solutions which were developed assuming ideal incompressible conditions. CFD simulation is used to evaluate the impact of varying the airflow in a descentionally ventilated airway on the layering along the roof of smoke and hot gases resulting from a vehicle fire. Control of the smoke layer is required to enable safe egress from the vehicle, particularly if the vehicle is for personnel transport, and to ensure control of the fire contaminants throughout the ventilation system. The airflow required to prevent layering against the ventilation direction, calculated from the Bakke and Leach relations (Bakke and Leach, 1962), is compared with the CFD simulation results. An evaluation of the pressures, generated as a vehicle enters a tunnel portal, using CFD simulation, is also presented for unflared and flared portal configurations. These simulation results are compared with predictions derived using an analytical method which assumes one-dimensional and incompressible flow. Results of the CFD simulation are presented in an animated video format. SIMULATION OF BACKLAYERING In designing a ventilation system for a transit tunnel, the ability of the ventilating air to control and prevent backlayering of smoke and hot gases resulting from a vehicle fire is of prime concern. The buoyant nature of hot smoke causes it to rise relative to the colder, fresh air provided by the ventilation system. If the vehicle fire occurs in a descentionally ventilated tunnel, the smoke may tend to move upgrade in a layer above the incoming ventilation airflow. The layer may become thick enough to engulf a substatntial part of the tunnel cross-section upgrade of the incident that comprises the evacuation route. This effect is termed "backlayering' and it is similar to the development of methane layers in mines for which most studies related to backlayering have been done. Prediction Techniques Analytical A number of studies have been conducted (Bakke and Leach, 1962) to define the characteristics of this phenomena and as a result have produced relations which are used both in the mine and transit ventilation fields to define the air velocities required to control layering. In the transit industry the air velocity required to prevent the backlayering phenomena from occuring during a vehicle fire is called the "critical velocity" (Associated Engineers, 1975) and is dependent upon a number of factors: tunnel height, cross-sectional area and grade; ambient air temperature and density; and the heat release rate of the fire. Common practice in transit ventilation design is to provide an airflow which meets or exceeds the critical velocity. In order to determine whether or not the critical velocity can be achieved with a particular ventilation system, a one-dimensional simulation of the tunnel network is typically performed using programs such as the Subway Environment Simulation program (SES) originally developed in the late 1970's (Associated Engineers, 1980). The results obtained from SES are compared to the critical velocity to determine the adequacy of the ventilation system. Computational Fluid Dynamics For the backlayering simulations, a commercial CFD code which has been used successfully in a wide variety of engineering applications, was used. It provides numerous options for modeling laminar and turbulent flows, multiple turbulence models, definition of multiple species and chemical reactions between them, a variety of boundary conditions (including constant pressure and constant velocity inlets) and the ability to apply user-defined FORTRAN subroutines. It includes the ability to model conductive, convective, and radiative heat transfer. FLUENT also permits the use of "body-fitted coordinates" to match the computational mesh or grid to complex real-world geometries. Computational Fluid Dynamics Model The model developed to simulate the backlayering phenomena is comprised of an airway of rectangular cross-section, 4 meters wide, 4.5 meters high, and 200 meters long. A laterally

Jan 1, 1995

By Musa I. Marto

The theory of ore flotation has developed at a rather fast rate and the application of theory to practice has been successfully investigated. Significant technological advances have been made in such areas as control of the ore grade, automation in metallurgical control through conductivity measurements, and the development of faster and continuous analytical techniques for ore pulp analysis. Further significant improvements in mill control are being_ investigated through the application of a computer control to the process. This represents the more advanced trend in process control. At the heart of a control system installation, the digital computer will communicate directly with process instrumentation, perform' complex calcu¬lations to determine on a timely basis the control settings for attaining optimum results and automatically furnish signals to effect control actions. The process is considered as an integrated unit and economic criteria are used to measure its performance. The approaches to a mathematical model development to describe the process, optimization and control schemes as applied to an ore beneficiation process will be discussed.

Jan 1, 1962

By Robin J. Batterham, Stephen H. Algie

It is often stated that innovation is central to the economic survival of mining and mineral processing in the face of global competition, and yet technology is often far from a core strategy in our industry - hence the concerns that are often voiced about the apparent slow rate at which new technology is applied. Much of the discussion stems from a lack of understanding of the role of technology in innovation, and of the role of R&D within the innovation process. To a large extent this has all been said, however, the messages are clear and deserve repetition. This paper expresses the personal views of the authors, based on experience in government-funded (CSIRO and universities) research, and in CRA Ltd, a large mining and mineral processing company. Further than this, it explains how our own development unit within the CRA Group has come to see its key roles as including the transfer of technology, and the training of technologists to move into the operating business units. We conclude that these critical tasks are the keys to creating the environment that will allow us to maximise the contribution of technology.

Jan 1, 1995

By R. J. Nankee

Recent on-going efforts to develop commercial coal cleaning beneficiation processes using chlorinated solvents-as the separating media will be described. True heavy media separations were performed on raw coal feedstocks, including Pennsylvania anthracite; Western, Eastern, and Midwestern bituminous; and lignite coals. Separation techniques included bath-type devices, cyclones, and liquid/liquid partitioning. Details on separation devices, removal of solvent, and recovery and recycling of solvent will be discussed. Projected costs of full-scale plants will be given for various coal sizes. A number of the coals evaluated are good candidates for beneficiation using chlorinated solvents. Coal beneficiation is desirable to provide needed coal quality. These needs include low ash fuels for coal water slurries and low sulfur fuels to meet emission regulations. In October of 1985, a paper, "Chlorinated Solvents for Coal Beneficiating"' was presented at the fall meeting of SME-AIME at Albuquerque, New Mexico. It reported the results obtained from various coals as feedstocks and of the separations using chlorinated solvents. These beneficiation results depended on true heavy media gravity and liquid/liquid partitioning separations. This paper will include detailed descriptions of the liquid/liquid partitioning process used in "Dow's Advanced Coal Cleaning Technology?2 and of the "Dow Solvent Recovery Technology.?3

Jan 1, 1987

By A. J. Monhemius, S. Raghavan, G. W. Warren, E. Peters, D. W. Furerstenau

A lyometallurgical process for extracting copper from an ore containing chrysocolla by leaching it with a kerosene solution containing LM 63 in the presence of small amounts of aqueous ammonia is described. The experimental results indicate that 70 to 75 percent of the copper can be extracted from the ore using an ammonia content that is about one-fourth the stoichiomeaic quantity required to leach copper in an aqueous leaching system. The rate of copper extraction was found to be a function of particle size, ammonia concentration and temperature. The large quantity of physically adsorbed water together with ammonia in the pores of chrysocolla provides a mechanism for the transport of copper to the external surface of the particles where it is complexed by the LM molecules and transferred into the organic phase. When size reduction accompanies leaching, the extraction process was found to proceed when only "trace" quantities of ammonia are present in the system. The kinetics of the extraction process appear to be controlled by a mixed (reaction and diffusion) mechanism.

Jan 1, 1993

By W. C. Streib

A wide variety of materials have satisfactory to superior insulating properties and can be used to control the flow of heat, provide energy savings, improve personal comfort and contribute to personal safety. Such materials range from completely organic products--both of natural origin and synthetics--to completely inorganic. In many cases, thermal protective systems are actually combinations of both. Obviously, those insulating materials which are principally inorganic have the inherent advantages of low to minimal combustibility as well as utility at vastly elevated temperatures. Both of these properties are highly desirable in providing not only thermal energy conservation, but also personal safety in residential and commercial applications. As the thermal insulation needs of man and industry have developed, there has been an ever-increasing demand on the minerals industry to provide the resources required to fill these needs. On a global scale, industrial minerals have become the fundamental base upon which today's thermal insulation industry has been built. The use of minerals to control heat flow range from the most unsophisticated applications to those requiring the ultimate in scientific technology. In many cases the minerals are themselves converted in- to the major insulating media; for example, fiber glass, rock wool or refractory fiber. In other cases, minerals are used as the chemical reactants to form the binder matrix which in turn provides the product strength required for adequate handling and installation; for example, calcium silicate bonded products wherein the binder is the reaction product of lime and silica. In still other cases, low density mineral products are added to a high density binder System to provide lower weight and better insulating properties; for example, the use of expanded perlite in concrete.

Jan 1, 1976

By Hans G. Kok

At this time in the history of engineering and construction, cost indexes give weekly evidence of the sharply rising costs of labor and materials. Paralleling the rise in construction costs are the costs of plant maintenance. Automation of the modern industrial plant has permitted a substantial reduction in the total number of employees required for plant operation. Of this reduced total, however, up to one-half of the employees may be engaged in plant maintenance. Management's decision to risk investment capital for a pro- posed plant or improvement is increasingly dependent upon the engineer's ingenuity in designing plant systems and structures which will require a minimum of materials and labor for manufacture, installation, and operation and which will be maintenance-free to a maximum degree. This paper concerns itself with the structural elements of bulk material handling systems in which the foregoing factors influenced the design to a considerable extent.

Jan 1, 1969

By C. B. Manula

The total systems model for underground coal mine planning and design (Master Design Simulator) is a set of computer programs which encompasses a realistic reproduction of the interaction among the geological, environmental, equipment, methods, and the health and safety aspects of the mining plan (Manula, Rivell, and Ramani, 1975). The total system includes nine major subsystems: geology and reserves, methane generator, roof support, subsidence, production, rail haulage, cost, water generator, and ventilation (Fig. 1). The subsystems themselves are divided into two categories based on the frequency with which they are executed: (1) event-oriented subsystems are executed either independently or at discrete intervals when certain specific events occur; and (2) dynamic subsystems function interactively during the production cycle, transferring data to or requesting data from event-oriented subsystems only when specific events occur (Fig. 2). Each subsystem has been tested and validated independently (Ramani, White, and Sutton, 1974; Ramani and Owili-Eger, 1974; Manula, Mozumdar, and Jeng, 1974a; Manula, Mozumdar, and Jeng, 1974b; Manula, et al., 1974; Manula, Rivell, and Sanford, 1974; Ramani, McClay, and Burgos, 1975; Manula and Owili-Eger, 1975; and Ramani, Owili-Eger, and Manula, 1975).

Jan 1, 1979

By Joe Keane

DOUG HALBE: The kickoff speaker, and my unanimous choice, is Joe Keane. Joe was born in Butte, Montana, and began his association with the mining industry as an under- ground miner at age 16. Currently he is president of KD Engineering and Metcon Research. He had it lucky when he went to school because there were only 44 elements in the periodic table, I understand. [laughter] Here's Joe. JOE KEANE: I'm doing this under protest. Maybe we can start the slides. Mr. Halbe gave me this topic, but I don't like it. I don't like Mr. Halbe either [laughter] because of the way he shanghaied me into this. He called me up on the phone and said this is what you're going to speak about: "Five Things I Never Want to See Again in Plant Design," and I said, "Huh!" Then I started getting stuff from SME about how to make a presentation. I have decided to change the title to "More Than Five Things I Never Want to See in Plant Design," since you can't have a completely negative speech; you have to have other topics. So we will have some other, not completely nonrelated, topics to sort of break the tension. I tried to find a joke to open with. I talked to Omar Mutati. All of his jokes were either about Bill Clinton, our beloved President, or they were too filthy to say in a mixed group. [laughter] So I decided to start this out with a profound statement. The pro- found statement is, "The meek shall inherit the earth, but not the mineral rights," [laughter] by J. Paul Getty. J. Paul Getty was one of my favorite guys because when a real obnoxious reporter asked him one day, "How can I become wealthy?" he said, "Drill for oil and find it."

Jan 1, 1998

By John R. Hawley

Ontario, one of the richest mining districts in the world, is a natural storehouse for much of the earth's fresh water supply. Covering over 344,000 square miles, the surface of this Canadian Province is dotted with 250,000 fresh water lakes and is laced with uncounted thousands of fresh water rivers and streams. The southern portion of the Province, for the most part, is flat or lazily rolling farmland. This is where most of the people in Ontario live. Although it is not a major mining area, southern Ontario does possess important deposits of salt, oil, gas and gypsum. Most of these deposits are being actively worked. Toronto, the capital city of Ontario, lies deep in the southern region. Here the climate is mild and the winters are short. The total annual precipitation consists of 27 inches of rain and 65 inches of snow. Most of the major mining companies that do business in Canada have made Toronto their Canadian headquarters. There are two reasons for this. The first, of course, is money. Toronto is the gathering place of many well- known financial institutions. The second is access. Toronto lies within a few hundred miles of some of the most spectacular mining enterprises that exist in the world.

Jan 1, 1973