Search Documents

By Edward Holloway

The basis for the selection of the ultimate pit for an open pit mining operation is generally opaque. Some form of value-based analysis will generally guide the final decision; however, the value will often gradually plateau whilst the ultimate pit size continues to increase. There is no established framework to guide specialists in the selection of the ultimate pit, with such decisions regularly made on a somewhat arbitrary basis. The key component that is missing from the analyses typically used to select the size of the ultimate pit is risk. Once risk is quantified within the analysis framework, the decision-making range is significantly reduced, and the process for selecting the ultimate pit becomes more consistent, replicable, and defensible. This paper provides an approach to including risk in the process used to select the ultimate pit.

Feb 21, 2024

By E. Woodburn, R. Putman, A. L. Mular

Optimization strategies of possible interest to mineral processing are reviewed and typical strategies initiated in processing plants to date are discussed. Both On-Line and Off- Line optimization procedures have been employed by industry, assisted either by operators or by digital computers. In every case, dollar benefits have accrued.

Jan 1, 1976

By Karl R. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fie or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. most longwall coal mines in australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflowmonitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

May 1, 2013

By Larry Powell

Rend Lake is an Army Corps of Engineers reservoir located in Franklin and Jefferson Counties in south-central Illinois. The lake consists of 20,000 acres of water and 19,000 acres of public access land. The site attracts over two million visitors a year and is surrounded by campgrounds and other recreational facilities. The lake overlies the largest tonnage of low sulfur coal in the state. Coal is being removed beneath the lake from five mines operated by three coal companies. Currently high extraction mining operations are approaching low-lying, environmentally sensitive, and high-use recreational areas. Advanced planning to maximize coal extraction and minimize potential effects of subsidence requires the development of procedures to assess the impact of high-extraction mining on the land use of the area. The Bureau of Mines, the Corps of Engineers, and the coal companies have initiated research to assess the following proposed planning steps to ensure the maximum recovery of the coal resources while minimizing impacts to surface land use: 1) Establish a dialogue between the surface and mineral owners; 2) develop a geographic information system to aid in assessing existing land use and potential changes; 3) assess the potential effects of subsidence on drainage, wildlife habitats, and changes in land use prior to mining; 4) coordinate the mining displacements with surface activities to minimize disruption; and 5) develop appropriate mitigation plans before mining occurs.

Jan 1, 1986

What is your assessment of the current state of the minerals industry? It is no understatement that domestic mining is facing a severe crisis at this time. The sharp decline in commodity prices and demand is putting a great strain on domestic and worldwide mining, causing major declines in profits and market capital of mining companies. This, in turn, has lead to major production cuts, layoffs, shut-downs of operating properties, and the deferral of new and expansion projects. These changes in the minerals industry have played a major role in the health of the economy. Operationally, the industry continues to develop new technologies that are making our work more efficient, more cost effective and more environmentally acceptable and safe. During downturns like this, companies generally pay closer attention to operational efficiencies and process optimization. Historically, new technologies and processes tend to be developed during down markets, and I believe we will see the same thing as companies strive to preserve liquidity and maintain or improve their margins. On the positive side, the drop in commodity prices has resulted in a reduction in operational costs, as the costs for fuel supplies and construction materials have decreased.

Jan 1, 2009

By M. M. Fine

One of the most persistent topics at technical gatherings and in the recent scientific press has been the reduction of iron ore. To cite some of them, in May 1960, a symposium on the subject was sponsored by the Electrochemical Society. The proceedings, comprising two dozen papers, were later published.3/ More recently, November 1966, a similar gathering took place at Michigan Technological University, Houghton, Mich. The latest meeting was the International Congress on Production and Utilization of Reduced Materials, Evian, France, May 1967. If the volume of literature, symposia and conferences is a measure of industry concern, then current interest must be at a high level. To the casual observer of the metallurgical scene, the abiding and recurring attention to iron ore reduction outside the blast furnace must be somewhat puzzling in that so much research endeavor has resulted in so little commercial activity.

Jan 1, 1968

By Louise H. Michaud

An interactive mine planning system that employs recent advances in 3D computer graphics capabilities and 3D geologic modelling to aid with the tasks involved in producing dragline mine plans was developed. As well as offering large potential saving in the time required to carry out the planning tasks, the system offers immediate visual feedback to the planning engineer. This can greatly aid in the conceptual understanding of complex geology and mine plans. The package incorporates the generation of a three dimensional Gridded Seam Model (GSM) as the basis for the development of the geologic database. This modelling method is capable of accurately representing rugged topography and multiple coal seams, including folding and faulting. The GSM is then integrated with an interactive graphics mine planning system in order to develop one model and one database for the generation of the mine design, the depletion of the coal resources and the movement of spoil material. The gridded structure of the model also provides the foundation on which all mine and spoil pile volumes are calculated.

Jan 1, 1992

By C. H. Grant

On the Mesabi Range, Ammonium Nitrate is used for blasting a variety of materials having widely varying blasting characteristics. The materials vary from hard, dense, magnetic taconite, which requires heavy blasting, through relatively soft, earthy, direct shipping ores, which require only light blasting to facilitate shovel operation. In view of the fact that materials gradational between these two end members are encountered in large tonnages, it is evident that a wide range of blasting situations face the mine operators on the Mesabi Range. In April of 1956, at Cleveland-Cliff s Hawkins Mine near Nashwauk, Minnesota, a fertilizer grade of Ammonium Nitrate prills was first used as a blasting agent. This first attempt was made without the addition of any carbonaceous material and even though it did go off, the force was not sufficient to produce the required results. Fuel oil was then added In the amount of one gallon for each 80 pounds of Ammonium Nitrate, with the oil and Ammonium Nitrate being added to the hole simultaneously. This blast was successful. Since then most of the mining companies have used Ammonium Nitrate, experimenting with various ratios of oil and fertilizer, mixing these ingredients either before or during loading of the holes. Since the additional of fuel oil to the Ammonium Bitrate before loading produces a more uniform saturation, most companies have adopted the method of pouring the fuel oil directly into the Ammonium Nitrate bags and then pouring the mixture into each hole. The ratio of 3- ½ quarts of fuel oil to each 80 pound bag of Ammonium Nitpate prills is now being used.

Jan 1, 1958

By N. Ward

The Gualcamayo Mine is located in the Andes Mountains north of San Juan, Argentina (Fig. 1). A property of Yamana Gold Inc., it declared commercial production in July 2009 and has a total mineral reserve and resource base of approximately 88 t (3.1 million oz) of gold. Crushing operations for the openpit mine are located in a 13,500-m3 (477,000-cu ft) underground cavern with a ceiling height of 22 m (72 ft). More than 3,600 m (11,800 ft) of tunnels are used to access the cavern and convey the ore. The project as described in this paper relates to the design and construction of the main cavern, conveyor system exit tunnel, the mechanical system access tunnels and two 4.2-m- (13.7-ft-) diameter shafts (Ore Pass #1 and Ore Pass #2) (Fig. 2). Preliminary engineering for the project was performed by Hatch Chile. Rizzo Associates Argentina, S.A., a division of Paul C. Rizzo Associates, Inc. (Rizzo), was contracted to provide geomechanical and geotechnical support for the construction of the access tunnel system and geomechanical design and construction supervision for the cavern and shafts.

Jan 1, 2011

By Nai-piu Tong, Huaren Dou, Sui-shun Poon, Leslie H. Swann

This paper mainly presents geotechnical aspects of a vehicular underpass that was built across under one of the busiest highway in Hong Kong. The underpass, in a section comprising an upper arch and invert slab, is approximately 6.2 m high at crown and 15 m wide at the base level with 40 m in length. The construction inevitably requires the underpass to be built using tunneling techniques to keep the overheadroad traffic uninterrupted. The paper will describe the design of temporary support for the tunnel excavation that was provided by an arch formed with horizontal pipes, which were installed using the pipe ramming method. The pipes arch was then supported by steel ribs founded on rock or mass concrete. Permanent lining design consideration was also discussed. Results of numerical modeling of the soil-structure interaction using the 2-D computer code FLAC will be presented. The predictions have been compared to the monitored results during construction, which indicates the prediction is in reasonable agreement with the measurement in the light of ground movement. The construction challenges will also be discussed in the paper.

Jan 1, 2003

By H. Maleki

The U.S. Bureau of Mines pioneered the use of borehole deformation gauges and overcoring techniques to measure in situ stress. These measurements provide input to structural mine design and support selection for specific geologic conditions. This paper presents recent stress measurements in a western U.S. coal mine where the orientation of the stress field remained relatively unchanged over distances of several kilometers. The horizontal stress magnitude increased with depth of cover and in relation to major geologic structures. Local variations in roof stress profiles were used to develop generic models relating stress arching to strata stiffness and the inelastic behavior of mine roof.

Jan 1, 1994

By David R. Hargis

Large-scale groundwater withdrawals are necessary to depressurize a confined aquifer system allowing the dry open-pit mining of the overlying phosphate ore. The extent of the existing and planned groundwater development led to the establishment by the State of North Carolina of Capacity Use Area No. l. Groundwater use in the Capacity Use Area is regulated by a permitting system. A two-dimensional finite-difference ground- water flow model was developed for North Carolina Phosphate Corporation. The aim of the model is to aid the Corporation in matters relating to permitting by serving as a predictive tool. The model can be used to project regional water level impacts resulting from various scenarios of depressurization pumping.

Jan 1, 1983

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the U.S. National Institute for Occupational Safety and Health collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants revealed not having a systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. In this paper, we identify and describe three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication and specialized training, to increase awareness of imminent danger situations. IntroductionIn recent years, the metal and nonmetal mining sector, as categorized by the U.S. Mine Safety and Health Administration (MSHA), experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured, twice the number of fatalities in each of the previous two years (MSHA, 2015a). As a way to address this increase, MSHA issued its P15- IV-01 program policy letter, suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners” (MSHA, 2015b). The goal of these examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 9, 2018

By Ross A. Scarano

It wasn't until late 1976 that the U. S. Nuclear Regulatory Commission (NRC) set about to address the uranium tailings issue in earnest. It was decided that a generic environmental impact statement related to uranium milling operations would be prepared to support formal tailings regulation. We recognized, however, that this was a task that would take many years to complete and we could not take a "business as usual" approach to tailings management in the interim; the issue was too sensitive. To facilitate licensing during the interim period, the NRC developed guidelines in May 1977, for the industry in the form of the following performance objectives for tailings management: Siting and Design 1. Locate the tailings isolation area remote from people such that population exposures would be reduced to the maximum extent reasonably achievable. 2. Locate the tailings isolation area such that disruption and dispersion by natural forces is eliminated or reduced to the maximum extent reasonably achievable. 3. Design the isolation area such that seepage of toxic materials into the groundwater system would be eliminated or reduced to the maximum extent reasonably achievable. During Operations 4. Eliminate the blowing of tailings to unrestricted areas during normal operating conditions. Post Reclamation 5. Reduce direct gamma radiation from the impoundment area to essentially background. 6. Reduce the radon emanation rate from the impoundment area to about twice the emanation rate in the surrounding environs. 7. Eliminate the need for an ongoing monitoring and maintenance program following successful reclamation plan. 8. Provide surety arrangements to assure that sufficient funds are available to complete the full reclamation plan.

Jan 1, 1980

By Michael J. Cruickshank

MICHAEL J. CRUICKSHANK SENIOR AUTHOR Marine mining is a very broad field. It encompasses every facet of terrestrial mining but with the unique addition of a superimposed liquid overburden, which is itself mineralized. It is the unique aspects of marine mining that are discussed in this section. In keeping with the times, a systems approach is taken in the presentation of the material. The environment is first described, and this is followed in logical sequence by the common requirements for working there, then the mineral exploration phase, the exploitation and, finally, the operational restraints imposed by man and nature. Free use is made of tables and figures from original and published works and extensive listings of reference material round out each section. The title "Marine Mining" was chosen in preference to ocean or underwater mining because it is broad enough to include oceans, beaches and inland seas. The selection of terms sometimes may seem odd but they have not been chosen arbitrarily. All things are reduced, where possible, to basics and defined. Applying systems terminology, the word "platforms" is used in the functional sense and includes not only airborne, waterborne and fixed platforms, but man himself in his capacity as a working diver. If there is confusion it is often because of familiarity with a word in a context personal to the reader. For example, what does extraction mean to you-or mining or exploitation? Cost data have been interspersed throughout the section whenever they could be obtained. The use of these data should be tempered with understanding because no two situations are alike and improvements in marine technology are constantly being made. The names of individual authors are listed with each subsection. Where no name is given, the responsibility has been that of the senior author. Acknowledgment is sincerely made to the U.S. Bureau of Mines, and latterly the National Oceanic and Atmospheric Administration, for encouraging and supporting the preparation of the work ; to the secretarial staff at the Marine Minerals Technology Center and to Donald Eisman for editing. To the many other contributors who may not be listed by name, grateful acknowledgment is also due. It is hoped that the chapter will be useful to the practicing mining engineer who suddenly is assigned to marine work or to the experienced marine engineer who is equally suddenly assigned to mining work. It is not possible to put "everything-you -need-to¬-know" into one section, but. the very full bibliographies at the end of the text should adequately fill in for those who wish to know more. 20.1-THE MARINE ENVIRONMENT Marine mining is set apart as a separate discipline by the marine environment. The following subsections describe the environment from the point of view of the physicist, the chemist and the geologist. The interrelationship of these disciplines with the economic mineral potential of the oceans and seas is apparent from the description of the marine mineral resources. The marine environment is an extremely complex natural phenomenon with which the marine mining engineer must learn to live. It can be the source of his wealth or his frustrations and sometimes both. It can never be ignored.

Jan 1, 1973

By V. Montaruli, A. Nieto, M. Cardu

Nickel is a metal whose workability and mechanical strength at high temperatures and in corrosive environments makes it an indispensable alloying element for the realization of stainless steel, specialty steel, super-alloys, rechargeable batteries and electroplating. Because its main fields of application are key to the development of industry and, thus, to society, nickel has recently been recognized as a potentially critical mineral, despite its abundant reserves. The purpose of this paper is the creation of possible case scenarios determined by factors and events that, in the medium to long term, could change the current structure of the nickel market on the demand and/or the supply side. Four scenarios have been determined by considering a demand variation due to the occurrence of a natural disaster and an aerospace plan implementation and taking into account the resource nationalism and the skills shortage as supply varying factors. Through the creation of a georeferenced global nickel database, the paper proposes supply strategies related to the four scenarios for each top nickel consumer: China, India, European Union, United States and Japan.

Jan 1, 2013

By Louis W. Cope

The various types of placer deposits will be described as an introduction to the subject. The several methods and machines used for sample taking and processing will be discussed. The advantages and disadvantages of each will be covered. Included will be mistakes and pitfalls of placer sampling and sample reduction.

Jan 1, 1987

By Donald Whittaker

Severe climatic conditions in mines are normally associated with working at depth. More precisely, it is a matter of working in regions of high strata temperature, since, for example, some coal mines in the Ruhr have strata temperatures at 1000 m which are matched only at 3 times that depth in the South African gold mines. In Britain we are perhaps fortunate in encountering strata temperatures in our deeper coal mines some 10-15 K lower than at the same depth in the hot mines of the Ruhr. Nevertheless the problems of high temperatures and humidities in UK mining operations, which in the past have been confined to a few specific sites, have in recent years become more widespread, and there is every reason to suppose that the trend will continue. Clearly strata temperature is not the only .causative factor. Long ventilation circuits serving districts remote from the shaft must also play a part, while the heavy use of machinery and the rapid, rates of excavation of modern mining methods are obviously important. It is necessary to understand the mechanisms of all such factors, and to measure their magnitudes and fluctuations, if remedial measures are to be properly designed or predictions made which are accurate enough to be of use in ventilation planning. This paper presents the results of a long-term (and continuing) investigation carried out in several mines to measure the major sources of heat and moisture on longwall districts and trunk conveyor roadways. The variation with time of these sources is reported, and the resultant effect on the climate is considered. In their investigations of the heat exchanges occurring in a whole mine Oakes and Hinsley (1955-56)1 listed and estimated the magnitudes of a large number of heat sources. Some of these, namely autocompression of the air in the shaft, diesel engines and compressed air mains, do not apply to the present investigations, which refer to longwall districts with conveyor transport and no compressed air supply. Others, such as oxidation of coal and, desorption of methane, have not been taken into account in the measurements, but are discussed later. One other source, the importance of which was pointed out by Gracie and Matthews (1975)2, is the coal on the conveyor, a form of strata heat emission, but one which is strongly dependent on the rate of coal production. The heat emissions measured in the present investigations were the energy consumed by electrical machinery, the heat conducted from the strata and the heat lost by the conveyed coal. Most of the emitted heat was removed from the district by the ventilation air, and was measured by continuously recording the enthalpy of the air at fixed stations. The heat removed by service water, supplied for machine cooling and dust suppression, was also measured. Account was of course taken of the relatively minor changes in level around the districts, in terms of the potential energy gained or lost by the coal and by the ventilation air (autocompression).

Jan 1, 1980

By Kerry Burns

Contrary to active subsidence, which occurs concurrently with mining operations, or is completed within a few days following coal extraction, delayed subsidence may take many years to appear at the surface after coal mines are abandoned. There are two principal morphological types of delayed subsidence: troughs, which are shallow depressions, and sinks, which are steep-sided crown pits. Both types are damaging to surface structures, and a variety of methods have been introduced to deal with the problem, ranging from subsidence insurance to site restitution. In planning insurance or restitution measures, a predictive model is of value in estimating the magnitude of the problem and the size of long-term budgetary commitments. Only one model is known, which was developed for the Bureau of Mines by GAI Consultants of Monroeville (l,2,3). The GAI model is presented in qualitative terms. This report develops a formal basis for the model and tests a numerical implementation on one of the best-described study areas, Allleqheny County in Pennsylvania.

Jan 1, 1982

By Hsu-Hui Hsing

In several previous studies from this laboratory (1-4) the autophobicity concept of Zisman and co-workers (5, 6) has been extended to gas phase adsorption processes. Low molecular weight alcohols adsorb on silica or alumina to yield novel isotherms in that monolayer adsorption occurs at low relative pressures indicative of strong bonding, but subsequently multilayer adsorption is quite sparse and diminishes with molecular weight of the alcohol. Such isotherms fit no standard classification scheme, however, in the vacinity of monolayer coverage alcohol isotherms give an excellent fit to the Langmuir or B. E. T. , Type I model (7). Monolayer adsorption is relatively irreversible and it is thus possible to prepare these chemisorbed layers and perform subsequent adsorption studies thereon. All indications are that the adsorptive properties on such films is radically different from that on the underlying alumina (4, 8) and in one study finite contact angles for hydrocarbon fluids were observed. One perennial conceptual difficulty is that there is no observed upper bound to the adsorption isotherm which would be necessary for autophobic adsorption to occur. The cause for this has been studied, and it is currently believed that adsorption is complicated by reversible capillary condensation at contact points between powder particles. The evidence for this is that large particle powders give less "apparent" adsorption at high relative pressures and in one very tedious study adsorption on planar sheets, oxidized aluminum displayed similar reduced uptake at high relative pressures when compared with high specific surface area powders (3).

Jan 1, 1974