Search Documents

By Jan Jekielek

Increasing capacity of bulk material handling systems creates difficult problems for accurate in-line material weight measurements. At the same time increasing system complexity and growing user demands call for more measurements. Precision in-line weight measurements for bulk materials are usually accomplished by application of conveyor belt scales. Belt scale accuracies listed by scale vendors are applicable for ideal situations with suitable conveyor design, belt scale location and calibration means. This paper attempts to provide designers and users with simple means to evaluate belt scale accuracy for practical scale installations. Based on known mathematical models simplified formulas for measurement errors are derived and discussed. These formulas allow for simple determination of achievable accuracy for alternative scale installations on the conveyor, conveyor designs, etc.

Jan 1, 1979

By William J. Orlandi

The intent and scope of this paper is to present to you, as concisely as possible, the problems and requirements -- and what we consider advantages -- of all-belt haulage in a modern underground coal mine. Mine No, 10, at Pawnee, Illinois, was opened in 1951; consequently, all the planning and consideration given to haulage selection was based on information then available and on Peabody Coal Company? s experience to that date,

Jan 1, 1961

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By W. G. Lacy

Anticipation of problems and the adoption of corrective measures in the design of engineering structures, establishment of pertinent building codes, and urban planning and zoning to obtain optimum land usage and conservation of natural resources demands a thorough understanding of geological conditions of a developing urban area. In the and to semi-arid southwestern United States erosional and depositional processes result in special situations that require special precautions in building practices. A series of studies currently underway in the Tucson area prompted by foundation failures and breaking, of buried service lines serve to illustrate some of these relationships between the geological environment and history, and engineering problems.

Jan 1, 1963

By Edgar F. Cruft

It is sometimes said that "mines are made, and not found". I rather doubt that the exploration geologist would be overly sympathetic to that statement, and, of course, like most one-liners it is only partly true. As an explorationist who has been involved in building his own company over the last ten years, and by necessity has become a financier, I can appreciate what real grains of truth are in that statement, however. Because technical people are seldom taught financing in their basic training, and because they are usually not involved in it until at quite a senior level in their careers, the whole field often acquires a certain mystique. The engineering professions have too often believed financing is the province of the accountant or financial executive and just as we in the technical world are often too quick to bristle if the latter try to tread on our domain, the opposite can just as easily be true. Unfortunately, this is another example of a compartmentalized individual, and that is one thing the successful financier cannot be.

Jan 1, 1979

By Don Opacic

The disposal of sludges and other similar industrial wastes is a major problem. Liquid wastes from industrial operations, when treated, produce significant volumes of sludge which are difficult to dispose of, because of the chemical and physical properties of the sludge. In the mining industry sludge is produced from various water treatment operations, in particular mine drainage neutralization. Waste water from coal preparation plants also produces a sludge however the sludge is in fact a slurry containing clays, coal fines and coal impurities. In many areas the disposal of these sludges is producing a serious problem. Mine drainage sludge consists of a variety of hydrous iron oxides, usually ferric oxides, contaminated with other neutralization products such as calcium sulfate. The volume of sludge from mine water or mine

Jan 1, 1973

By W. W. Vaughn

In the technique described and evaluated, detection of mercury is based on the principle of atomic absorption. An analog signal, produced when mercury vapor absorbs ultraviolet light, is converted to digital form and calibrated to mercury concentration. Interferences are eliminated by selectively trapping the mercury on gold. The lower limit of sensitivity, using a 1-gram sample, is 5 parts per billion. A model of the instrument mounted in a station wagon has been tested successfully in the field.

Jan 1, 1964

By D. D. Young

During the 1970's a number of covered storage facilities were constructed in North America to store and handle large quantities of bulk, solid materials. This trend, away from outdoor storage piles, will probably continue at a stronger pace in the 1980's. This paper attempts to answer some of the questions often raised about the economics of large covered storage facilities. The paper is in four parts: 1. Why Build a Storage Facility? 2. 2. Common Components of Storage Systems With Details of Six Storage Facilities 3. Results of a Study for 50,000 Mg Clinker Storage 4. Guidelines for Conducting a Study to Select a Storage System.

Jan 1, 1980

By Melvin A. Jennings

Even though the title of this paper is quite long, the ideas presented herein are very simple. In fact, it occurs to me to be somewhat humble about coming before such a distinguished group with such a simple presentation. However, the application of these ideas has proven useful in at least two copper flotation plants. The purpose in presenting this paper is to inspire some interest in the great stores of data chat the Mining Industry often accumulates without making any attempt at analysis. Unfortunately, many milling engineers rely rather heavily on percent recovery as a strict measure of a concentrator's relative performance. The fallacy of this reasoning is not difficult to see since, by definition, percent recovery is a function of feed assay, tails; and concentrate grade. If copper tailing is constant, and it very nearly is for a strictly sulfide copper ore, percent recovery must fluctuate almost directly to the feed assay. The point that I wish to make here is that it is very seldom justified to compare the percent recovery figure from one period of time to another without considering the difference in feed assay. The problem of comparing results is even further complicated when the ores are of mixed oxide and sulfide mineralogy.

Jan 1, 1978

By Saul Escalara

Data on sulfonate adsorption by silicate minerals are very scarce in the literatures. Perhaps the only comprehensive paper written on the topic was done by Fuerstenau and Bhappu (1); this work dealt exclusively with quartz but included many important suggestions as to the form and nature of the hydroxy-sulfonate species of some cations formed during the conditioning step and their effect on the flotation response of quartz. Another paper by the same authors (2) contains additional data on the role of hydrolysis in sulfonate flotation of beryl. As postulated by Fuerstenau and Bhappu, a solid form of cationic sulfonate functions as the collecting species to produce flotation of quartz and beryl. According to the authors, the solid compound is a hydroxy-sulfonate of a given cation, where the hydrogen of the hydroxyl part provides a means for bonding of the species to the mineral surface; thus, the presence of hydroxyl in the neutral precipitated compound is of primary importance to produce flotation. Although the preceding examples illustrate the effect of a sulfonate collector in silicate systems other than plagioclases, they are important as examples of processes of hydroxy-sulfonate complex formation. Since the plagioclase minerals con¬tain Ca(II) and Al(III) cations, which are very reactive in sulfonate media (1), the formation of hydroxy-sulfonate compounds with these cations released from the solid phase may well prove to be the cause for their flotation.

Jan 1, 1973

By Toru Nakao

Fujiwara Quarry had been operated by the "Glory-hole Benchcut" mining system. But because it became difficult to meet the expanding demand by this system, "Central- shaft MCP" mining system was introduced in 1979. This MCP is equipped with a hydraulic walking system manufactured for the first time in Japan. Nowadays "Central-shaft" mining is the common method at limestone quarry in Japan. In this method crushing facilities are usually installed at the bottom of the shaft. But at this quarry, MCP was adopted and installed on the quarry surface. Many MCPs are operated in foreign countries, but in Japan few examples exist. Normally, Japanese limestone deposits lie in high mountains, which is obviously inconvenient for MCP to walk in and around the quarry. This difficulty, however, was overcome at this quarry, and MCP has been operated satisfactorily and efficiently for about 2 years after it was installed. In order to overcome the difficulty, in "Cen¬tral-shaft MCP" mining system, two mining methods are employed, the one is "SLICE-DOWN" mining method, and the other is "BLOCK-CUT" mining method.

Jan 1, 1982

By Bruce Hebblewhite

"Historically there have been a number of different hypotheses and empirical models developed in an attempt to describe the nature of fracturing above longwall panels in underground coal mining. The motivation for such models varies, ranging from understanding the impact of mining on surface subsidence to back-analysis of caving behaviour in the immediate roof behind the longwall face. One of the most critical motivating factors that is taking on increased importance in many coalfields is the need for better understanding, and hence prediction of the impact of mining on overlying strata, particularly strata units acting as aquifers for different groundwater horizons.This paper reviews some of the major prediction models in the context of observed behaviour of strata displacement and fracturing above longwall panels in the Southern Coalfields of New South Wales, south of Sydney. The paper discusses the parameter often referred to as “height of fracturing” in terms of the critical parameters that influence it, and the relevance and appropriateness of this terminology in the context of overlying sub-surface subsidence and groundwater impact. The paper proposes an alternative terminology for this parameter that better reflects what it is and how it is used. The paper also addresses the potential role of major bedding shear planes mobilised by mining and their potential influence on overlying subsidence and groundwater interference.INTRODUCTIONKnowledge of the detailed nature of rock deformation and failure above any form of large-scale underground mining is always going to be limited to interpretation from a very incomplete set of data. It is extremely difficult, if not impossible, to directly measure the detailed nature of the rock failure, fracture networks, and deformational behaviour above an extracted mining area. Limited techniques such as borehole extensometry can provide some evidence of relative or incremental deformation in the direction of the borehole (usually vertical). However, such data cannot assist below the horizon where full caving has caused major rotation and dislocation of rock blocks and effectively destroyed the instrumentation borehole. Above such a horizon, the data is only valid along the axis and in the direction of the borehole, and to the level of detail defined by the extensometer anchor spacing intervals. It is often also restricted by major shear planes intersecting the extensometer borehole and cutting off the instrumentation below the level of the shear horizons."

Jan 1, 2019

By William R. Barton

The domestic portland cement industry consumes more than 12 million tons annually of raw materials chemically similar to fly ash. How these materials are used and how fly ash can serve in their place are discussed. Factors influencing whether or not a particular plant will use fly ash in place of an alternate material are discussed.

Jan 1, 1968

By Leonard Sargeant

The Pocahontas Coal Field consists of eight mineable seams of low-volatile coal in southern West Virginia and Virginia. The deeper seams, especially the Pocahontas No. 3 and No.4 Seams, under heavy cover and below drainage are notoriously gassy. Methane in the Pocahontas Field is generally thought of as being confined in the coal itself, rather than in mud slips or clay veins. Furthermore, it is characteristic of Pocahontas coal to retain its gas until the coal is broken and removed from the solid. Because of this inability for gas to escape from unmined coal, entries developed around large blocks are seldom of significant value in bleeding off methane before pillar extraction begins. This is evidenced by the fact that it is not uncommon to find gas liberated during the mining of chain pillars and barriers which have been developed for several years. The Pocahontas Fuel Company develops almost all solid coal by conventional methods with shuttle car haulage. To provide the maximum productive capacity without compromising ventilation and safety requirements, the Company has adopted standards for ventilating 5, 6 and 7-entry sections.

Jan 1, 1960

By Walter E. Heinrichs

To many, petroleum exploration and successful geophysics , are partly synonomous, This is not because natural petroleum is usually concentrated as a liquid, nor certainly not because oil can be detected directly. The reason is Chat geophysics helps to at least better understand and sometimes, to even explain the essential geology involved. That groundwater is similarly a liquid with all but a few of its basic geologic relationships practically identical to petroleum, seems to have escaped many of those most interested and responsible for complete geo-hydrologic knowledge. The paramount need to use every means at our disposal for maintaining and expanding our crustal resources reserves are generally obvious, However, in view of the rapidly mounting requirements, continual re-emphasis is worthwhile.

Jan 1, 1963

By William A. Vogely, Robert T. Deacon, Walter J. Mead

Oil and gas together are the most important energy sources consumed in the United States. In 1983, 67% of total energy consumption was represented by these two resources (43% was oil and 25% natural gas), while coal accounted for only 23% of U.S. energy use. All other sources (hydroelectric, nuclear, geothermal, wood and other waste products) accounted for only 10% (U.S. Department of Energy, 1983, p. 1). In this chapter we address the issue of regulation in the oil and natural gas sectors of the U.S. energy industry. In addition, we analyze the cartel characteristics of the Organization of Petroleum Exporting Countries (OPEC). If OPEC is an effective cartel, then U.S. oil as well as substitute energy prices, production, and consumption will be affected by cartel action. Further, as the nation learned in the 1970s, major changes in oil prices produced major disturbances in other sectors of the U.S. and world economies. Consequently, it is important to determine whether the roughly ten-fold increase in nominal prices that occurred in the 1970s was the result of cartel action, the result of normal economic forces adjusting to the fact that the world was running out of cheap oil, or some combination of the two. Furthermore, the presence of OPEC- associated oil price increases is related to regulations that were imposed on the energy sector during the decade of the 70s. THE RATIONALE FOR GOVERNMENT INTERVENTION Economists have traditionally judged the state of an economy to be efficient if it is impossible to improve the welfare of any one member of society without harming someone else. Any economy that satisfies this condition is said to be Pareto efficient, after the Italian economist Vilfredo Pareto who first gave rigorous attention to such questions (see Chapter 4.10). It is easy to see why an economy that fails to satisfy this condition could not be efficient; by definition, it would be possible to alter the allocation of resources in a way that improves everyone's welfare.' Much of the appeal of this weak efficiency criterion is that it avoids comparisons of levels of well being among different individuals. The cost of such generality, however, is that in any given economic system a wide array of different Pareto efficient states will typically be attainable. In the simple Robinson Cursoe economy of the undergraduate textbook, for example, efficiency could just as easily be attained in the case where most of the island's resources are owned by Friday as in the case where they are under Crusoe's control. However, the distribution of welfare among the two inhabitants would obviously be quite different in the two situations. Such equity issues cannot be settled on objective or scientific grounds. To decide which distribution of welfare is socially "best" an explicit value judgment is needed. It is useful to keep in mind the preceding distinction between efficiency and equity issues when analyzing the role of government in a market economy. Decentralized market processes will not necessarily result in a distribution of welfare that society considers just. For this reason a potential role for government lies in the redistribution of income among individuals. In some circumstances, however, market pro-

Jan 1, 1985

By D. R. Gibbons

This morning I would like to speak to you about an area of chemistry that is enjoying a revival-organometallic compounds. This renewed interest, principally stimulated by defense needs, has already created new markets for the products of the mineral industry. Although the consumption of metals in these new products is modest at oresent, several hold promise of importance. Because this is a new and growing market, I am sure the Council of Economics is aware of many of its facets and is interested in new developments. Of course, the chemical industry has been a significant consumer of minerals for many years. I estimate that in 1957 the chemical-industry purchased a total of $1175 million worth of minerals as raw materials (not including fuels). This estimate can be broken down as follows: [Metals and metallic minerals $375 million Nonmetallic minerals (excluding hydrocarbons ) 330 million Hydrocarbons 470 million $1175 million]

Jan 1, 1958

By Charles E. Weaver

A core from the La Camelia attapulgite mine in north Florida was studied in detail to determine the detailed vertical variability and the relations of the various parameters. The structural, textural, mineralogical and chemical data indicate there are two major depositional cycles represented within the minable interval. The sediments deposited during the two cycle differ in detail but in general are similar. The environments of deposition grade from shallow marine to lagoonal to tidal flat to marsh. The sedimentary structure (lamination, burrows, pebble conglomerate), mineralogy (attapulgite, montmorillonite, sepiolite, dolomite, calcite) chemistry (Al, Mg, Fe) are closely related to each other and their nature is determined by the depositional environments. Most of the clay minerals and carbonate minerals are authigenic and are therefore particularly sensitive to environmental differences. The variability and environmental features seen in this core are characteristic of the sediments in the general attapulgite mining area. A detailed understanding of the relationships discussed should be of value in prospecting, mining and processing.

Jan 1, 1972

By A. M. Gaudin

In a recent paper we have reviewed principles and applications of measurement methods for contact angles and their hysteresis (22). In this paper we apply these methods to a system consisting of rutile, an organic liquid (benzene, decane, or dodecane) and water. Surfactant (dodecylamine hydrochloride) was used at various concentrations and various pH values.

Jan 1, 1964

By Henri Letient, Tom Aley, David Evans

Antamina is a large open-pit copper and zinc mine located within the Central Andes of Northern Peru at an altitude of 4300 masl. The facilities are situated within the headwaters of several watersheds, within the Amazon basin. Nearby villages rely heavily on springs and streams for drinking and irrigation water. The principle source of baseflow during the dry season is from Cretaceous karstic limestone aquifers. Antamina will produce nearly 1.4 billion tonnes of waste rock over its mine life. Finding suitable sites for storing large volumes of waste rock is often a challenging task – especially in karstic, alpine terrain. Detailed hydrogeological investigations are essential for delineating the karstic hydrogeologic watersheds associated with the proposed waste facilities, which are often very different than topographic (hydrologic) watersheds. Contamination vulnerability mapping at Antamina consisted of geological and karst mapping, geophysical surveys, geochemical testing, dye-tracer studies, drilling and aquifer testing. Detailed mapping followed by dye-tracer studies proved to be the most cost-effective methods for characterizing the karst aquifer systems. The results were used to optimize waste rock management at the site to minimize potential impacts on groundwater resources.

Jan 1, 2005