Search Documents

By H. Y. Yang, L. L. Tong

For gold recovery, a Chinese refractory, high-sulfur gold concentrate was subjected to biooxidation with high pulp density in a single stirred-tank reactor. The flotation concentrate contained 36.9 percent sulfur (S) and 33.9 percent iron (Fe). Different experimental regimes for biooxidation were applied. With a mixed culture and by controlling the amount of addition of the gold ores and the pH of the biooxidation system, maximum iron oxidation of 82.6 percent and sulfur oxidation of 79.3 percent were achieved. The experimental results indicate that the pH control was beneficial to the biooxidation of this concentrate. Approximately 28.4 percent of elemental sulfur (S8) was found in the oxidizing slags. Two dissolution mechanisms of elemental sulfur are proposed: (1) FeS2 → S80 → S2O32− → SO42− and (2) FeS2 → S80 → SO42−. The high pH had a positive effect on the reduction of the S8. The results of thermodynamic analysis indicate that as an oxidant the dissolved oxygen can effectively reduce the Gibbs free energy of the pyrite oxidation process and, compared with the reaction of ferric iron as the single oxidant, the oxidation of pyrite is easier. The efficiency of the gold recovery was related to the iron oxidation as well as the sulfur oxidation. Gold and silver recoveries of 92.4 percent and 66.4 percent, respectively, were achieved.

Column flotation cells continue to gain acceptance in the coal industry for the treatment of high-ash streams containing clay slimes. Unfortunately, some industrial installations have failed to meet expectations due to improper scale-up, incorrect operation and poor ancillary circuit design. To overcome these problems, case studies have been conducted to fully define the capabilities of column cells for coal applications. These data have been used to develop generic engineering guidelines for column circuit design and operation. An economic analysis has also been conducted to illustrate the importance of key capital cost considerations. These analyses indicate that column cells are significantly more expensive than conventional machines, although this difference can be greatly reduced through the installation of very large-diameter columns.

Jan 1, 1999

By T. R. von Ow

The method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said that almost every decade in the last half century had its own trend. The trends were dominated by the market demand, the advanced process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology. The increasing size of the ring geared mills in the last years requires more awareness on the drive train solution. Special attention must be paid to the mechanics and the requirements of the power grid. Operational challenges such as soft starting and controlled operation as well as the protection of the equipment have gained importance. Frequency converter drive solutions dedicated to single or dual pinion ring-geared mills offer significant advantages over conventional drives due to their application specific features and controls. Solutions with low speed motors as well as high speed motors cover all possible configurations available for ring geared mills.

Jan 1, 2010

By T. L. Myron

In recent years increasing attention has been given to improving both the chemical and physical properties of sinter. The first step toward this goal was the production of a self-fluxing-sinter. More recently, blast-furnace operators have found that significant improvements in blast-furnace performance can be achieved by improving and controlling the physical size of the sinter. The results of full-scale blast-furnace tests have shown that blast-furnace production can be improved by using a closely sized agglomerate. The improvements obtained by the use of pellets, a closely sized agglomerate, are well known. In contrast, blast furnaces charged with sinter having a wide size spectrum have generally not yielded results as satisfactory as those from furnaces 1) * charged with pellets. Beginning in 1958, Appleby-Frodingham charged plus 3/8-inch sinter to their blast furnaces. Further tests by other companies in Canada, 2) the United States, 3) and Australia showed that blast-furnace production could be improved by about one percent when the plus 3/8-inch material in the burden was increased by one percent. Because of the promising results obtained with screened sinter, an extensive test program was initiated to determine an effective means of producing sized sinter in U. S. Steel's sinter plants. This paper describes the work done by the Applied Research Laboratory in this program.

Jan 1, 1965

By Ralph Musick, Brian Briggs

The U1h Shaft Project is a design/build subcontract to construct one 6.1 meter(m) (20 feet [ft.]) finished diameter shaft to a depth of 321.6 meters (m) (1055 ft.) at the Nevada Test Site (NTS). Atkinson Construction was subcontracted by Bechtel Nevada(BN) to construct the U1h Shaft for the Department of Energy (DOE). The project consists of furnishing and installing the sinking plant, construction of the 321.6 m(1055 ft.) of concrete lined shaft, development of a shaft station at a depth of 297.5 m(976 ft.), and construction of a loading pocket at the station. The outfitting of the shaft and installation of a new hoist may be incorporated into the project at a later date. This paper will describe the design phase, the excavation and lining operation, shaft station construction and the contractual challenges encountered on this project.

Jan 1, 2001

By Ratnakar Singh, Raj Kishore, Kisor Kumar Sahu, Ranjeet Kumar Singh, Ganesh Chalavadi

The Falcon concentrator is capable of separating minerals in fine size classes based on their differential density. Separation of mineral particles depends upon the fluid flow characteristics and relative movement of particles in a fluid. In the present study, a fluid flow characteristic inside the Falcon concentrator was established through experimentation and modeling. The Falcon concentrator has two fluid entry points: (a) Fluid entering through gravity assisted feeding system and (b) Fluid entering through the fluidized hole on the concentrator wall. In order to identify the role of fluid entering the concentrator, a tracer was injected into the system. As per the tracer based experimentation, it was established that fluid entering through the gravity based feeding system is responsible for thin flowing film formation in the stratification zone where particles are stratified based on their relative density. The momentum balance and continuity equations were simplified for a high centrifugal force field, and the fluid velocity profile was estimated inside the thin flowing film. Estimated fluid flow profiles will help to simulate the particle trajectories inside the Falcon concentrator. The influence of rotational speed, fluid flow rate, and cone angle on the fluid velocity profile were investigated. Fluid thickness over the concentrator wall is also estimated, and it is typically of the order of ~150–200 μm.

By Raj K. Rajamani

In ball milling the rates of breakage vary primarily with the size distribution of powder in the mill. In wet grinding viscosity of the slurry varies continually as size distribution changes and hence the breakage rates change. In this study a simpler estimation scheme is used to determine breakage rates in batch grinding. Using an approximate solution to the batch grinding equation, acceleration and deceleration of breakage rates of all individual size classes is determined when the grinding environment is varied. Experimental results with limestone and copper ore show time-dependent breakage rates under both dry and wet grinding conditions. In general the breakage rates increase for coarse sizes and decrease for fine sizes with increase in the fines present in the mill. Such variations have strong implications in closed-circuit grinding.

Jan 1, 1991

By Aurel Goodwin

I chose the title "Let's Clear the Air" for this afternoon's presentation because it has two meanings, the literal and the figurative. Most of you know what MSHA is. Most of you know what MSHA does. And, for the most part, most of you know why. What I hope to accomplish today is to "clear the air" around our health standards, to clarify for you how MSHA views its congressional mandate under Title I Section 101(a)(6), (7), and (9) of the Mine Safety and Health Act. Asbestos, silica, radiation, noise, welding fumes, carbon monoxide, lead, hydrogen sulfide, nitrogen dioxide - the list of physical and chemical hazards encountered in the metal and nonmetal mining industry is as diversified as the industry itself, possibly even more so. In addition, miners are often exposed to several of these health hazards simultaneously.

Jan 1, 1980

By A. H. Brisse

In considering the use of a coal or a coal blend for the production of metallurgical coke, the fact is often overlooked that laboratory data can be most effectively used to determine coke plant operating conditions conducive to maximum output as well as to predict the quality of coke produced. The discussion here presented attempts to point out the manner in which carbonization data can be interpreted for industrial use and the significance of specific laboratory test results in this interpretation. The major considerable must, of course, be the safeguarded of coke oven batteries, against wall damage arising either from excessive carbonization pressures or from the wedging of the pushing ram into non-contracting coke charges. In order to be specific in the matter of handling the laboratory data involved, two series of blends are analyzed. The first of these, referred to as the "AB" series, is typical of some d' the more highly expanding Eastern- coal blends whereas the second series, here referred to as the "CD" series, is probably more typical of the Western coal blonds. Reference to Table II should be made for rank of coals considered in these blends.

Jan 1, 1959

By John E. Crawford

A year ago, if I had the pleasure of addressing you, I would have discussed ocean mineral resources from a promotional standpoint. I would have described exciting indications of mammoth tonnages of sea-floor industrial minerals. I would have attempted to fire your imaginations as to the potential of a nation having the technologic know-how to exploit its submerged boundaries. As a first step toward this capability, I would have solicited your support for a Bureau of Mines? program aimed at determining the industrial worth of marine minerals and devising techniques and hard- ware for their recovery. We still need your support, but recently we have ventured out of the realm of planning and into your Government's first program in marine mineral engineering. Today, I wish to describe what we have done within the framework of existing research problems and our possible goals. I will be brief so as to allow ample time for questions, and I can do this with confidence because our program is so new that I need not be chagrined at not having all the answers.

Jan 1, 1965

By William H. Dresher

A study has been made of the reaction mechanisms occurring during the salt-roast process to form water-soluble sodium vanadate compounds from the vanadium oxide compounds present in vanadium-bearing ores and concentrates. Two reactions have been identified, either of which lead to water-soluble compounds--oxidation of sodium chloride by water vapor and. oxidation of sodium chloride by oxygen. The former reaction has been found to be predominant in the salt-roast process. A kinetic treatment of the data has shown that for the formation of sodium metavanadate the rate-controlling step in the reaction, in which sodium chloride is oxidized by water vapor is the decomposition of a species containing water and sodiumm chloride, on the surface at the gas-solid interface. For the formation of sodium pyrovanadate, the rate-controlling step is the decomposition of a species containing water and sodium metavaradate on the surface. The transportation of water through the system, perhaps as a sodium chloride-water complex or a sodium metavanadate-water complex, and the actual chemical reaction are relatively fast compared to the initial surface decomposition step. A similar treatment on the data for the oxidation, of sodium chloride by oxygen has shown that the rate-controlling step, is the actual transportation of oxygen from the gas-solid interface to the reactive site. This transportation is by a sequence of two diffusion processes. Transportation during the early stages of the reaction is by the diffusion of oxygen through a continuous layer of reaction product. After, the first few minutes of reaction time a second diffusion process begins and is continuous for the remainder of the reaction. This second diffusion process involves the diffusion of oxygen, through a layer of reaction product that has developed voids around which the oxygen must diffuse. The hindering, nature of this latter process causes the rate of transportation of oxygen to the reaction site to be considerably slower than by the simple diffusion mechanism initially followed. A thermodynamic treatment of the data has shown that the energy of activation for the decomposition of the water-sodium chloride species on the surface is -12.1 Kcal. per mole. For the decomposition of the water-sodium metavanadate species on the surface' the energy of activation is -15.1 Kcal. per mole. The results of this study indicate the limiting mechanisms of the basic reactions occurring during the salt-roast process. These results suggest what variables should be examined in applying this information to actual plant operations.

Jan 1, 1961

By Jan M. Mutmansky

30.1-THE SCOPE OF SYSTEMS ENGINEERING JAN M. MUTMANSKY JAN M. MUTMANSKY 30.1.1-DEFINITIONS The terms "systems engineering," "systems analysis," and "operations research," common in today's technical literature, often are interchanged because of their similar meanings. However, some differences exist which need explanation. The most convenient way to achieve an understanding of the differences is to start with the definition of a system, namely, a collection of components which interact in a specific manner to accomplish a common objective. Accordingly, a haulage truck, a computer, a missile, a mining company or a nation each may be considered a system. Systems engineering generally can be defined as the conception, planning, design and engineering of any system of interacting elements so that the objective of the system is automatically optimized. Thus, systems engineering normally is con¬cerned with systems not yet activated.',' Systems analysis may be described as a scientific method of making decisions based on a quantitative or other objective evaluation of all action alternatives. It is very similar to systems engineering but usually is not considered to be restricted to problems of design prior to use. While the previous two disciplines are somewhat vague and can encompass a great variety of engineering functions, operations research can be more specifically defined as the application of mathematical models to the problem of optimizing the objective of any predefined system. Systems analysis and systems engineering are closely aligned sciences but opera¬tions research differs in the following ways. First, it generally is associated specifically¬with optimization and mathematical models while the other two often are not. In addition, it, is used predominantly on well-defined problems which can be ex¬pressed in mathematical terms. However, systems engineering or systems analysis may deal with highly complex social or governmental systems which may be ill¬defined and unsolvable by the classical methods of operations research. Finally, systems analysis and engineering always strive to look at the entire system to avoid the problem of suboptimization often necessary in operations research because of the necessity for a mathematical model. Because of his more extensive system, however, the systems engineer often is less able to find the optimal system. In summary, operations research, systems analysis and systems engineering are very similar in purpose but one, operations research, is more mathematical in nature and forms an important part of the other two activities. Other definitions which may be helpful are provided by Griffiths 3 Wilson,4 Falkic 5 Hall,2 Quade and Boucher, 6 and Flagle et al. 1 30.1.2-METHOD AND TECHNIQUES The systems or operations research approach makes use of scientific problem solving. The basic procedure comprises the following general steps: 1. Definition of the problem. 2. Construction of a model of the system. 3. Testing of the model under known conditions.

Jan 1, 1973

By Warnie Flint

According to statistics compiled by the National Safety Council, US Bureau of Mines, American Medical Association, and other agencies, accidental injuries cause more deaths than all the leading diseases. No one is immune to an accident. Probably the best way to describe an accident is to say that it is an unexpected happening. The automobile driver is not expecting a terrifying crash, the electrician does not expect to be electrocuted, nor is the coal miner expecting the roof to fall on him. All personal injuries will not result in death. There is a multitude of victims who are living proof of what accidents can mean to an individual-victims who are blind, paralytic, missing arms, legs, etc. In most instances the earning power of these individuals is gone, and they are utterly dependent upon family or welfare. For many years there seemed to be an attitude that prevailed in industrial America that accidents were inevitable, and that so many fatalities and injuries should be expected. This, of course, was utter nonsense. Since the birth of such organizations as The National Safety Council, American Society of Safety Engineers, and. the US Bureau of Mines, much progress has been made in reducing accidents. The enactment of compensation laws greatly contributed to the progress that has been made. Does this mean that all accidents can be prevented? Unfortunately, it does not. Human psychology indicates that men will work unsafely or perform unsafe acts for the following reasons : 1) Lack of knowledge or skill. 2) Conflicting motivations, such as: (a) to be more comfortable, (b) to save time or effort, (c) to be accepted by a group. 3) Physical or mental condition. Nearly everyone desires his own safety, but not all individuals are willing to do what they know to do to insure their own safety.

Jan 1, 1981

By George W. Land

For the year 1985, the U.S. coal industry produced 881 million tons of bituminous coal and lignite. Domestic consumption amounted to 814 million tons. The electric utilities consumed 689 million tons, almost 85 percent of total consumption, over 78 percent of production. In May, 1986, the NCA forecast that with moderate growth rate averaging 1.9% per year from 1985 through the year 2000, production could reach 1,176 billion tons and domestic consumption 1079 billion. The estimate for electric utilities indicate 924 million tons for the year of 2000, about the same percentage of production and consumption as now experienced. Before we consider the main topic of this paper, the cost of using high sulfur coal, let us examine the coal use patterns of the last 25 years, the changes in those patterns and consider the reasons for those changes. Table I shows those changes.

Jan 1, 1986

By Thomas Pollard

It is truly remarkable how the image of longwall as a method of mining has changed. Between 1920 and 19609 viewed on a world wide basis, longwall was regarded as a' system for difficult and deep conditions and associated with intensive labour extraction. Today the world looks on longwall in the hope that it can produce the next really big break through in productivity, Three correlated machinery developments have made this possible, but it is not only the machinery developments, interesting though these be in themselves, but together with developments in control systems of these machines that longwall now looks so much more attractive, The machinery concerned is, of courses:- 1. The Anderton Shearer Loader - A miner that takes a narrow strip off the, face at rates acceptable to modern mining engineers. 2. An Armoured Flexible, Conveyor which can be kept in close contact with the face and still convey coal as it is snaked over to the faces 3. Powered support systems which can be mechanised and controlled with reliability at any distance from the individual support itself.

Jan 1, 1964

By Ian Graham

In 2013 the Government of New Zealand launched a number of ‘National Science Challenges’ (NSC) to address major issues facing the nation, and raise public consciousness about science and its role in promoting evidence-based decision making. One of the 10 proposed NSCs focuses on New Zealand’s extensive Exclusive Economic Zone (EEZ) and Extended Continental Shelf (ECS)1, with an objective to enhance utilisation of marine resources within environmental and biological constraints, and the desired outcome of:

Sep 1, 2014

By Robert P. Bell, John T. Waggoner

The Metropolitan Water District of Southern California is designing new outlet facilities for Lake Mathews, including a junction shaft, connecting tunnels, and an ear-shore outlet tower. Since Lake Mathews must remain operational during construction, groundwater inflow potential is a concern. This paper describes the challenges and methods used to investigate rock mass and groundwater conditions at an operational reservoir, where offshore and onshore geotechnical exploration was performed. Several investigative and analytical methods were used to characterize rock mass and groundwater conditions, including rock coring, downhole geophysical and video surveys, hydraulic conductivity testing, automated groundwater level monitoring, and laboratory testing.

Jan 1, 1999

By Olav Moklebust

The R-N Process is an outgrowth of the development by the National Lead Company's Norwegian subsidiary Titania A/S, of a process for producing metallic iron and a high titanium content co-product from ilmenite. Development of the process for the treatment of iron ores was continued as a joint project of the Republic Steel Corporation and the National Lead Company in 1953. More recently in July, 1957, the R-N Corporation was created by these two companies to undertake the commercial promotion of the results of this joint project. This paper has been prepared with the permission and encouragement of these three companies. The R-N process has as its objective the making of metallic iron from iron ores or iron ore concentrates. The general principles of the process have already been disclosed in technical papers and patents. In general the process comprises the following steps: 1. Iron oxide in crushed natural iron ores or iron ore concentrates is reduced to about 95% metallic iron, without fusion in a rotary kiln in the presence of solid carbonaceous fuel,*such as, coke or char, limestone and combustible gases. 2. The kiln discharge, consisting of metallized ore, coke, lime and coke ashes, is cooled. The excess coke is regenerated and recycled to the kiln feed.

Jan 1, 1959

By Dennis Molvik, Omar Fulton, Chris D. Breeds, Don Gonzales

The Tolt Pipeline No. 2, West Snoqualmie Valley project, is part of a water supply project linking the Tolt reservoir in East King County to the City of Seattle through a nominal 2.13 m (7-ft) inside diameter conveyance. Receipt of the National, 2002Microtunnel Award provided recognition of the many challenges overcome by this project. Baseline conditions revealed in the Geotechnical Documentation included over-consolidated glacial deposits, landslide and alluvial deposits, artesian water, boulders up to 36-in in diameter, logs, heaving sands, and liquefiable soils beneath the river. Schedule constraints associated with setting the shafts in the floodplain of a salmon bearing river and the fickle performance of the river during those times it was not supposed to flood added to the challenge.

Jan 1, 2003

By Stephen P. E. Redmond

A 15 km water supply tunnel is being constructed in Buenos Aires, Argentinata expand the capacity of the existing system. Two 4.3 meter diameter Earth Pressure Balance (EPB) tunneling machines operating at times from the same shaft on a congested work site and advancing through sedimentary deposits underlying this wonderful city pose interesting challenges. As of January 1999approximately 50% of the tunnel has been excavated. Combined machine production rates of 1026 m/month have been achieved. Presentations made in prior proceedings can be referenced for details of the overall Project scope and for details of the tendering process. The purpose of this paper is to compliment those presentations by addressing now the execution of the work.

Jan 1, 1999