Search Documents

By Yuanbo Zhang, Guanghui Li, Zhenyu Fan, Tao Jiang, Xiaohui Fan

"Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60% of the total. Aiming at the features of sintering flue gases and existing problems during the flue gas desulphurization, a technical route of flue gas circulation sintering (FGCS) for iron ores has been put forward. Under the simulated experimental conditions, effects of FGCS process on the main output and quality indexes and SO2 emission rule are researched using simulating flue gases. Compared the novel FGCS with conventional sintering process, SO2 in the final sintering flue gas is obviously enriched and the total exhaust gases can be reduced evidently. The decreasing of oxygen content in circulating gases has bad effect on the sintering indexes. Increasing the oxygen potential is beneficial to obtain high quality sinters. This investigation shows that the FGCS process is promising.IntroductionSteel is a kind of essential material for modern society, but steel-making process is characterized by high energy-consumption and emission as well as heavy environmental pollution. Chinese steel industry has developed rapidly in the last decade, and the environmental problem caused by ironmaking and steelmaking have also aroused the greatest concern, especially the atmospheric pollution caused by SO2, CO2, etc. Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60 % of the total. The development of the desulfurization process for sintering flue gases to reduce SO2 emission in sintering process is not only the requirements of sustainable development but also the most important environmental tasks for steel industry [1-5]."

Jan 1, 2011

By Motohiro Horiguchi, Kazuo Ichii, Toshio Oishi

"As a fundamental study to prepare copper-based alloys with rare earths (RE: La, Gd, Nd, Ce and Y) without any inclusions, the solubility of rare earth in liquid copper was experimentally determined. Liquid copper alloys were equilibrated with carbon and rare earth carbide in a graphite crucible in an argon atmosphere at 1523-1873 K.Solubilities of rare earth in liquid copper were determined by approaching the equilibrium values from both the lower and the ·higher concentrations than those expected· in the preliminary experiments. They were expressed as a function of temperature. Carbon in Cu-RE alloy was also analyzed and thermodynamically discussed.IntroductionOver the past several years, the demand for highly conductive and high strength copper-based alloys, such as Cu-Cr, Cu-Zr and Cu-Cr-Zr for use in electronic materials has increased.1 -7 These alloying elements are very reactive and easily oxidized to form oxide inclusions during melting. To avoid the oxide inclusions, it may be effective to utilize the strong reducing power of carbon in conditions under which no carbides form.In this study, to provide fundamental data for producing Cu-RE( rare earth) alloys without any inclusions, the solubility of rare earth in liquid copper in equilibrium with .carbon .was determined and discussed on the basis of the experimental results and the thermodynamic data.ExperimentalSample preparation for equilibrium experimentsOxygen-free copper (99.99%), lanthanum (99.9%), gadolinium (99.9%), neodymium (99.9%), cerium (99.9%) and yttrium (99.9%), and their oxides were used as starting materials.Each rare earth carbide was prepared by mixing rare earth oxide with carbon, which is a little more than the stoichiometric composition, pressing it into a tablet form and sintering at about 2000.K for 20 ks in a vacuum furnace using a graphite crucible. Powder X-ray analysis showed that only the carbon and rare earth carbide (REC2) was present in each sample.Cu-RE mother alloys (5-20 mass % RE) were prepared beforehand by mixing metallic rare earth with oxygen-free copper, and melting in an electric arc furnace."

Jan 1, 2000

By J. M. Skeaff

As much as 100% of the gold and 67% of the silver in a sulphur-bearing hydrometallurgical leach residue have been transferred to copper metal at copper smelting temperatures by dissolving the partially calcined residue in an iron-bearing slag maintained in equilibrium with the liquid copper metal and matte phases. The precious metals can then be recovered by conventional refining techniques. Copper can be recycled at least four times without any detrimental effects on gold and silver transfers and recoveries. Apparent copper recovery in the .process can be over 100% because of the copper content of the residue. Based on slag analys.es, the overal1 recovery of gold in the copper metal and matte phases varies from 94% to 100% under all conditions investigated. On the? same basis, silver recovery varies .from 9S% ?to 99% under optimum conditions, but is only 4S% to 73% under other, less attractive conditions. Unaccounted for silver losses of' about 30% make it difficult to determine the major factors affecting ?silver transfer and recovery. A method for implementing the technology on a commercial scale at a Canadian copper/zinc smelter has been proposed. A preliminary economic assessment and comparison of the proposed pyrometallurgical process with conventional cyanidation indicates that either process is economically attractive for recovering gold and silver from leach residues. Although the capital costs are higher, the pyrometallurgical process is simpler, has higher recoveries, lower operating costs and no .potential environmental problems related to cyanide disposal.

Jan 1, 1989

By Thais Cristina da Costa Caldas, Carlos Mauricio Fontes Vieira, Alline Sardinha Cordeiro Morais, Sergio Neves Monteiro

"This work has as its objective to evaluate the effect of the incorporation of a glass powder waste obtained from discarded and Hg-cleaned fluorescent lamp into clayey ceramics used to fabricate bricks and roofing tiles. Formulations were prepared with incorporation of the waste in amounts up to 10 wt.% into the clayey body. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa to fire at 850 and 1050°C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The microstructure of the fired ceramics was evaluated by optical microscopy. The results showed that the waste incorporation significantly improved the evaluated properties mainly at 1050°C.IntroductionFluorescent lamps use mercury as a main component for its operation. This metal is potentially toxic and can contaminate soils, animals and water bodies. The problem is aggravated if considerations are made with respect to the amount of lamps that are commercialized and discharged in emergent countries like Brazil [ 1].By using appropriate recycling processes applied to discharging fluorescent lamps it is possible to reuse most constituents of these lamps into new productive processes. A study has shown that one million common fluorescent lamps can generate 900,000 tubes of clean glass [2]. Moreover, this Hg-cleaned gloss may be recycled in different products.In fact, to recovery and recycle all materials that constitute the lamp instead of discharging them. This action protects the soil avoiding the formation of environmental passives [3]. It is also relevant to mention that the glass from fluorescent lamps is 100% recyclable while its permanence in the environment would correspond to very long time pollution, since its decomposition time is undetermined [4]."

Jan 1, 2011

By Shu Xinqian, Zhou Weining, Shan Zhiqiang, Feng Jifu

"Modified calcination conditions on the extraction of rubidium resources from muscovite (KAlz[AlSi301o](OH)2) ore are systematically studied. The impact of various factors on the rubidium leaching rate is also analyzed, including the agent types, roasting time, the mass ratio, roasting temperature, etc. The results indicate that the best agent is a combination of sodium chloride and calcium chloride, its mass ratio ofmuscovite/NaCl/CaClz is 1:0.25:0.25. Calcined at 8500 for 30 minutes, the rubidium leaching rate is up to 90%. The reaction of muscovite ore with the chlorinating agent CaC12 has been studied by TG/DSC, the calcined intermediates are identified by XRD, and the surface morphology before and after leaching is characterized by SEM. Rubidium chloride products can be obtained with a purity of 92% by using t-BAMBP extraction, hydrochloric acid reextraction and purification.IntroductionRubidium is one ofrare alkali metals, which is found in 1981 by German R.W. Bunsen and G.R. Kirchhof. Rubidium includes the following features: atomic number is 37, each atom weight 85, the body-centred cubic lattice, each unit cell has two metal atoms, and the density is 1.532g/cm3. The properties of low melting point (312.46 K) and malleability make rubidium have a strong chemical activity and photoemission. Rubidium provides a main material for manufacturing phototube with a wide range oflight waves, which possess high sensitivity and stability. Efforts are being made to carry out research on rubidium ion gngine, magnetic flux generators and thermoelectric transudcer, etc. Rubidium exists in muscovite ore(KA12[AlSh01o](OH)2 (monoclinic system and hexagonal layered structure) as isomorphism and replace the large radius of the potassium atoms, as well as part of rubidium locate between structure layers. The complex components bring great difficulty in comprehensive recycling."

Jan 1, 2013

By Zhang Chuanfu, Li Shixiong

"In the electrolysis electrodeposition or electroplating of aqueous solution of copper, lead, zinc, nickel, manganese etc, with the increase in cathodic over potential the reducing rate of metal and the cathodic current efficiency increases and the deposit becomes more compact and smooth. According to this principle, a method and equipment of the auto-control of electrolyte quality is invented. The industrial application shows that this method turns the experienced operation into auto-control. The quality and quantity of metal is improved greatly and the consumption of electric energy is reduced.In the electrolysis, electrodeposition or electroplating of aqueous solution of copper, lead, zinc, nickel, manganese etc, usually organic additives are added according to the state of cathodic deposit according to experience. This traditional and experienced operation, often lead to that the quality of additive is not optimum which affects the quality and quantity of metal and increases the consumption of electric energy. To counter the controlling problem of the quantity of additive, the authors have invented a corresponding equipment of the auto-control of electrolyte quality [1], it has found application in industrial practice."

Jan 1, 2000

By Jim Sundal

Primary steel manufacturers using electric arc furnaces generate one of the largest hazardous waste streams nationwide. The waste stream, known as electric arc furnace dust, is a listed hazardous waste with the designation K061. Oregon Steel Mills, Inc., (OSM) of Portland, Oregon, has implemented a process known as Glassificationn, which uses KO61 as an ingredient in an onsite recycling process. Because OSM was able to demonstrate that the Glassificationm recycling process beneficially uses all toxic constituents in the electric arc furnace dust and that the recycling process produces marketable products, the process is not subject to Resource Conservation and Recovery Act (RCRA) permit requirements. The marketable products manufactured using Glassificationn include roofing granules, ceramic glazes and colorants, abrasive blasting media and, more recently, synthetic slag fluidizers. The purpose of this paper is to identify the regulatory issues for recycling hazardous waste and demonstrate that OSM glass frit is effective as a slag fluidizer in primary steel manufacturing.

Jan 1, 1994

By Carvalho A. Felipe de

The search for environmentally friendly and cost-effective methods for gold extraction has been undertaken in order to provide alternatives to the use of cyanide leaching in the gold industry. Among such alternative reagents is the combination of chloride and hypochlorite ions due to their oxidation of metallic gold and its complexation. Therefore, the current work aims at investigating gold leaching from an oxidized material by means of a solution comprising calcium hypochlorite and sodium chlorite. The sample used in the current research contained 66.1% Fe2O3, 20.4%SiO2, and 35.7 g/t of Au. In addition, XRD and SEM-EDS analysis revealed iron oxide, quartz and muscovite as the main crystalline phases in the sample. For comparison purposes, cyanidation of the oxidized material resulted in 90% gold extraction in 24 h. The reference conditions for the leaching tests with the chlorite-hypochlorite system were: particle size −37 μm, solid/liquid ratio of 10% (w/v), 10 g/L NaCl, 10 g/L Ca (OCl)2, pH 5–6, 3 h of leaching. The effects of the: (i) Ca(OCl)2 concentration, (ii) NaCl concentration, (iii) pHrange and (iv) the effect of pulp density in the extraction of gold were assessed. In addition, the stability of the hypochlorite solutions (OCl−) was investigated. The ideal concentrations of Ca(OCl)2 and NaCl were determined as 25 g/L and 15 g/L, respectively, whereas the optimal pH range was 4–6. Under these conditions, the final gold extraction reached approximately 84%. By varying the solids content of the pulp (10%, 20% and 30%), it was observed that the lower solids value resulted in greater gold extraction (84%). The degradation of the hypochlorite solution and the possible catalytic effect of the presence of the solid were evidenced. To sumup, in the experiment, high gold extractions were achieved in shorter periods of time (3 h), as compared to the cyanidation of the same sample. On the other hand, itwas necessary to use significant amounts of the reagent due to hypochlorite instability at the pH conditions recommended for high gold extractions.

By M. Oliazadeh

Spodumene [LiAl(Si2O6)] is the most common and desirable economic lithium-bearing mineral due to its high lithium content. In Canada, there are several spodumene deposits at the development stage that have the potential to help narrow the forecast lithium supply gap stemming from the widespread acceptance and increasing use of electric vehicles. Spodumene processing can be conducted using Dense Media Separation (DMS), flotation or combination of both. If spodumene liberation is sufficient at coarse particle sizes, DMS can be used for primary lithium concentrate production and silicate gangue minerals rejection. If liberation is not sufficient, flotation is then the main processing route for spodumene concentration. Even in cases where DMS is a viable beneficiation option, flotation may still be required to process the DMS middlings and/or the undersize fraction which is outside the particle size range for DMS. Considering flotation as a technique for spodumene beneficiation, there are several alternatives including the use of mechanical flotation cells, column flotation cells, coarse particle flotation cells, and/or Staged Flotation Reactors (SFR), either alone or in combination. Ore sorting can be incorporated at the start of the spodumene flowsheet to remove gangue minerals, particularly amphibole and pyroxene in the early stages. The main objective of flowsheet development for hard rock lithium deposits is to evaluate the ability of these options to produce a spodumene concentrate with a concentrate grade above 6% Li2O, lithium recovery of above 80%, and with the minimum operating and capital cost. This paper aims to describe the various processing options available for the beneficiation of spodumene from hard rock deposits and compare the associated operating and capital costs for each.

By Daniel Hoffman, Katerina Aifantis, Ibrahim Miskioglu, Jaroslaw Drelich

"A new method to determine the elastic modulus of a material using the atomic force microscope (AFM) has been proposed by Tang et al. (Nanotechnology 2008, 19, 495713). This method models the cantilever and the sample as two springs in a series. The ratio of the cantilever spring constant (k) to diameter of the tip (2a) is treated in the model as one parameter (a=k/2a). The value of a, along with the cantilever sensitivity, are determined on two reference samples with known mechanical properties and then used to find the elastic modulus of an unknown sample. To determine the reliability and accuracy of this technique it was tested on several polymers. Traditional depth-sensing nanoindentation was preformed for comparison. Using both methods, the elastic modulus of the polymers tested was calculated. The elastic modulus values from the AFM were within ±(5-20)% of the nanoindenter results.IntroductionThe atomic force microscope (AFM) has proven to be a useful tool for characterizing materials on the micro- to nano-scale. The most common use of AFM is to image and measure the topography of the sample surface, but AFM has also been used to characterize the mechanical properties of materials [1-3]. With AFM's ability to scan the sample surface, features of interest can be found and indented. It provides an advantage over traditional nanoindenters that use optical microscopes and thus cannot resolve nano-scale features. This makes AFM a useful tool for characterizing materials on the nano-scale."

Jan 1, 2011

By F. H. A. Abdalla

A process is described for the recovery of valuable nonferrous metals from steelmaking dust by suiphatizing roasting using ammonium sulphate. Maximum recoveries of soluble metal sulphates achieved at optimum conditions were> 99.0 %. Selective metal separation of the soluble sulphates in the leached liquors were performed either by controlling the roasting temperature or by adjustment the pH values of the leached liquor ranging from 3.6-6.2. Either pure zinc oxide orland tin oxide could be obtained at optimum conditions, and the products were evaluated chemically and by X-ray analyses. The residues rich in iron oxide can be removed and recycled. The mechanism of sulphatizing roasting process was considered. A general flow-sheet for the overall process of treatment the steel making dust to recover its valuable nonferrous metals was suggested, which ca be applied for other nonferrous bearing materials.

Jan 1, 1996

By Xiao-hui Fan, Xu-ling Chen, Zhi-yuan Yu1, Guanghui Li, Min Gan, Yun-song Huang, Tao Jiang

Compared with the traditional de-NOx processes by cleaning the waste gas, a new approach for reducing the formation of NOx during sintering process is proposed. Since more than 90vol% of NOx comes from the fuel combustion, the influence of sintering coke breeze pretreated by CO(NH2)2 additive on the NOx emission is researched. As adding CO(NH2)2, the reduction agents (NHi) are generated during the pyrolysis of CO(NH2)2, which reinforce the NOx reduction, And the appropriate content of CO(NH2)2 is 1.0 mass% of coke breeze.

Jan 1, 2015

By Xuemei Zheng, Aiyuan Ma, Yonggang Zuo, Jinhui Peng, Shiwei Li, Libo Zhang

The effect of moisture content on the dielectric properties and microwave drying behavior of zirconium hydroxide was studied by using an open-ended sensor dielectric measurement system at the frequency of 2.45 GHz. The experimental results showed that moisture content can significantly influence the variation of dielectric properties. Dielectric constant, loss factor and loss tangent all increase with the increasing moisture content. Compared with the conventional drying method, the microwave-assisted drying method resulted in a substantial decrease (81.8%) in the drying time, and the drying effect was better at the lower power level of 600 W. This study offers the useful information on dielectric properties of zirconium hydroxide, which can be used for developing microwave drying applications in mineral processing and designing better microwave sensors for measuring zirconium hydroxide moisture content.

Jan 1, 2015

By Rajashekhar Marthi

Lithium is a key component for future electric vehicle batteries and energy storage. The future availability of lithium to meet the growing demands remains in question. Around 60% of lithium resources exist in the form of continental brines. Traditional methods to recover lithium from brines use solar concentration with precipitation and have found limitations in lithium extraction due to interference of Mg in high Mg/Li brines. Thus, there is a need for highly selective adsorbents. Recently, spinel structured delithiated lithium manganese oxides have demonstrated promising results. However, due to the small particle sizes, it is economically difficult to recover the adsorbents and thereby limits industrial applications. In our work, LiMn2O4 ion sieve was synthesized and immobilized on diatomaceous earth. Fundamental adsorption studies were carried out in lithium buffer solutions to understand the nature of adsorption and kinetics. The adsorbents were also tested for recycle stability, as well as recovery of lithium from Great Salt Lake water samples.

By Run-boWang, Fan-yi Meng, Jian-Liang Zhang, ZheWang

To elucidate the influence of high Al2O3 content on sinter softening and melting behavior, heating-up reduction test under load was carried out. In addition, microstructure study of sinter bed structure change at a different temperature was also made and the mechanism that the effect of Al2O3 content on sinter softening and melting property was discovered. SEM results showed that the increase of Al2O3 content favored the formation of Al2O3-rich slag phase, such as the eutectic (2CaO·SiO2-2CaO·Al2O3·SiO2-FeO) and gehlenite (2CaO·Al2O3·SiO2), resulting in the decrease of sinter Ts temperature. Further, high Al2O3 content improved the concentration of metallic iron and lowered the dripping temperature due to the decrease of slag liquidus temperature and viscosity. At a fixed basicity, it was indicated that there was a relationship between Al2O3 content and sinter softening-melting property. Based on the results, counter strategies to cope with the adverse effect of high Al2O3 content on the cohesive zone property were also proposed. It could provide guidance for the blast furnace operation of sinter with high Al2O3 content.

Jan 1, 2015

By I. Gaballah

Cadmium is toxic to plant, animals and humans. The council directive of the European Communities No 8315 13lEEC has fixed an upper limit of 200 ppb for the release of cadmium in industrial effluents. The conventional method of neutralization/prccipitation ( NIP ) is inefficient to reach this limit. The objective of this study is to test the efficiency of the trees modified bark to remove cadmium cations from industrial effluents after the conventional treatment by NIP. Laboratory scale tests with synthetic solutions show that the cadmium removal depends upon pH and initial concentration. About 99.9 %, 99 % and 96 % of the metal are removed from synthetic solutions containing 10, 100 and 1000 ppm respectively. Pilot plant trials ( 1 m3 ) with an industrial effluent bearing about 500 ppb of cadmium lead to the almost complete elimination of the cadmium ( final concentration is lower than the analytical detection limits < 20 ppb ).

Jan 1, 1994

By Tibor Zoltai

Asbestos is a generic term for industrially useful fibers recovered from exploitable deposits of the asbestiform varieties of five silicate minerals: chrysotile, anthophyllite, actinolite-tremolite, cummingtonite-grunerite, and riebeckite. Asbestos and asbestiformm fibers of some other minerals are known to be carcinogenic. Minerals crystallized in the asbestiform habit are characterized by unique properties (morphology, strength and flexibility, physical and chemical durability, and defect-free surface structures). The key to the unusual properties, and health effects, of asbestifarm fibers appears to be in their unusual surface structure. In contrast, non-asbestiform crystals of the same minerals, including the five so-called asbestos minerals do not have these properties and are not carcinogenic (1, 2).

Jan 1, 1989

By Nagahiro Saito, Takahiro Ishizaki, Mituhito Hirota, Akio Fuwa

"Owing to their extremely high toxicity in the environment, the dioxins have been attracting social, technical and scientific attention in recent years. The authors theoretically had predicted the thermodynamic properties of all the dioxins via quantum chemistry and statistical thermodynamics and elucidated the generation-decomposition behavior of dioxins in the equilibrium calculation· of C-H-0-Cl system. In actual combustion processes, it is said that metallic compounds have much influences on the dioxins behavior. The aim of this study is to reveal the roles of metallic compounds the generation-decomposition behavior of dioxins is revealed from the viewpoints of quantum chemistry. Especially, the catalytic effect of copper has been investigated for the reaction, 2HCl(g)--H2(g}+Cl2(g) and for the etherification reaction from precursors, which is Phenol(g) here, to dioxins. The catalytic role of Cu is shown to have much influence on the generation -decomposition of dioxins.1. IntroductionIt is well known that dioxins are very harmful not only for our health but also for that of our children and grandchildren because they are very stable substance and their reaction rates of decomposition are considerably low. On the other hands, it is not well know how dioxins are generated and decomposed; the generation-decomposition conditions and paths as well as the catalysts to decompose them'1l. The authors believe that the thermodynamic and kinetic study of dioxins is useful to find a solution to these issuers. The authors have been investigating the following problems to reveal the generation-decomposition behavior of dioxins; (a) the prediction of the thermodynamic parameters of dioxins (2), (3), (b) the generation -decomposition behavior of non-chlorinated dioxins by the thermodynamic equilibrium calculations in C-H-O system(4) and (c) the generation-decomposition behavior of dioxins by the thermodynamic equilibrium calculations in C-H-O-CI system(5). Summaries of these thermodynamic researches are as follows.(I) The thermodynamic parameters for dioxins, which had been unknown and/or inaccurate'6 l, could be predicted and are available within the scientific accuracy."

Jan 1, 2000

By G. Granata

In this work, we studied the recovery of copper from AMD by cementation with iron powder. To control the size of copper particles within the nanoscale range, we tested the use of the anionic surfactant sodium dodecyl sulfate (SDS). We tested three concentration levels (0.2, 0.4 and 0.6 M) and temperatures (25, 50 and 75 °C). The activation energy of cementation was also assessed by fitting the experimental data with the Arrhenius equation. Under all investigated conditions, the cementation reaction was found to be a diffusion-controlled process. Without surfactant, the activation energy was 19.9 kJ/mol. In the presence of SDS the activation energy increased up to about 35 kJ/mol. With or without SDS, the particle size of the copper product was strongly affected by the cementation temperature. Without SDS, the cemented product aggregated into micro-sized clusters of about 15 μm at 25 °C, 2–3 μm at 50 °C and 1 μm at 75 °C. The addition of SDS resulted in a dramatic decrease of copper particle size up down to the nanoscale range. Under the best operating conditions, the particle size of copper was <100 nm.

By Neal Schwartz, Robert De Saro, Richard Rosenthal, Ed Kear

"A Stack Melter has been installed and is currently operating at Lexington Die Casting. The Stack Melter consists of a 1 meter (3 foot) diameter refractory tube, 2 meters (7 feet) high. Specification ingots are continuously fed to the top of the melter and piled to nearly the top. A burner fires through the scrap which melts the lower portion and preheats the upper portion. As the lower portion is melted, it is drawn out and the upper preheated scrap falls to a lower level where it in tum melts. The molten metal is fed to one of two holding furnaces for eventual delivery to a casting machine.The Stack Melter's energy use is approximately 2900 joules/g (1,250 Btu/lbm), resulting in an overall energy savings of about 58%. This energy savings is brought about primarily because the flue gases preheat the scrap and the flue gas temperature is dropped to well under 528°C (1000°F)."

Jan 1, 2000