Search Documents

By D. J. MacDonald

Wettability measurements and laboratory waterflood tests were compared under a wide variety of conditions. Experiments were conducted with synthetic and natural crude oils, treated and untreated outcrop and oilfield sandstone cores, and synthetic brines with and without caustic, detergent, or phosphate additives. Measurements were made on equilibrated and unequilibrated systems at 77° and 150° F. Wettability was evaluated by the Bureau of Mines method from capillary pressure curves determined with a centrifuge. The waterflood data were fitted by empirical curves; the parameters of the curves characterize primary and subordinate production and also give the ultimate oil recovery. Results showed that wettability measurements at 77° F were useful predictors of recovery efficiency in waterflood tests run at both temperatures. Oil recovery in the early stages of waterflooding increased with increasing water wettability; however, the ultimate recovery was highest at a slightly oil-wet condition. The oil displaced at highest speed in the centrifuge was correlated with ultimate recovery in waterflood tests. Chemical additives to the brine sometimes lowered wettability and also sometimes improved waterflood recovery, but wettability and recovery were not correlated with additives present. The effect of additives on recovery in waterflooding was best seen in water-oil ratio curves.

Jan 1, 1974

By Thomas Novak, Robert Goldstein

The analysis of a machine-luminaire configuration is a time- consuming process requiring the construction of a machine mockup, installation of a designated lighting arrangement, and an extensive set of illumination measurements. This entire process, however, is well suited to computer analysis. By simulating the machine geometry and the characteristics of the desired luminaires, the incident light levels can be calculated at the required set of points. This Bureau of Mines paper presents a general description of the techniques involved in performing this simulation.

By Laszlo Toth

A feeder is used to control the gravity flow of bulk solids from storage areas, like a bin or a stockpile. For this type of application, it is important to select a proper drive that can fulfill all of the demands put on it. High starting torque capacity, variable speed and the ability to handle frequent starts and stops are some of the demands that the drive must be able to meet. The following is a comparison of the most common type of drives used today for feeder applications. When a feeder is started, the breakaway torque may reach as high as200% of the running torque. The accelerating torque usually is set to protect the carrying element of the feeder, like the belt for the belt feeder and the carrying chain of the apron feeder (Fig. 1).

Jan 1, 2003

By Jennifer Riefenberg

Ground control hazards, coal quality, ore reserve estimation, and pollution modeling seem unrelated topics from most mining perspectives. However, geostatistical methods can be used to characterize each of these, and more topics. Exploratory drill core data, and continued drilling and field measurements, can provide a wealth of information related to each of the above areas and are often severely underutilized. Recent studies have led to the development of the Multiple Parameter Mapping (MPM) technology, which utilizes geostatistics and other numerical modeling methods, to generate a "hazard index" map, often from exploratory drill core data. This mapping has been presented for ground control hazards relating roof quality, floor quality, numerically modelled stresses due to mining geometry, and geologic features. A review of the MPM method, future directions with the MPM, and a discussion of using these and other geostatistical methods to quantify coal quality, ore reserve estimation, and pollutant modeling are presented in this paper.

Jan 1, 1996

By J. D. Miller, C. L. Lin

As the techniques and resolution for 3-D spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional x-ray microtomography offers a unique imaging capability. Spatial resolution on the order of ten microns can be achieved with the use of microfocus x-ray generators. Recently, a state-of-the-art cone beam x-ray microtomography system has been installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility has been designed to obtain 2048 x 2048 pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind, instrument will be used to obtain three-dimensional spatial reconstruction for such applications as specific examples 3D liberation analysis, pore structure analysis of particle beds during filtration and air-void system of concrete structures. The utilization of x-ray microtomography not only will allow for quantitative analysis of multiphase systems but also allow for textural characterization and the determination of phase continuity. In this paper, we present information regarding the current use of this new facility and reviewed potential applications for the advanced analytical system.

Jan 1, 2001

By Virgil J. Stachura

The Bureau of Mines has investigated techniques and instrumentation that measure accurately the airblast overpressures from surface mine blasting. The results include equivalencies between broadband research instrumentation and commercially available impulse precision sound levels meters measuring: root-mean-square, peak, fast, slow, impulse, A and C weighting, C-weighted sound exposure level (CSEL), and "linear" (flat) response. These values were obtained from field measurements and broadband FM tape recordings of production blasts at area and contour coal mines, limestones quarries, and iron mines. Frequency response was determined for 14 commercial systems.

Jan 1, 1981

By Steve C. Albrecht

The objective of this study is "to assess the impact of surface mining on soil compaction in the Midwest". The study revolves around a unique field sampling program targeted at four mine sites utilizing four distinct types of soil movement of midwestern prime land. Through the preparation of a final report for use as a guidebook, an assessment is made of the degree to which surface mining operations contribute to the soil compaction problem. The final report is formulated through the use of field study data as well as information gathered in an intense literature review. The final report centers on applying collected data to practical field applications. Soil sampling on the four mine sites centers on a comparison of natural and replaced soils for moist bulk density. This characterization evaluates changes in density and texture throughout the soil profile to a depth of 48 inches. Fertility of the topsoil is also assessed for natural and replaced soils. During field sampling and observations, a base of information has been gathered to compile a case study on each mine site. The report accesses the regulations in the prime farmland areas through the use of a matrix. The regulatory matrix allows easy access of mining personnel to State and Federal regulations.

Jan 1, 1982

By José Mirão, Pedro Madureira, v Costa, Patrícia Conceição

"The exploration of seamounts south of the Azores during the EMEPC/Açores/G3/2007 campaign allowed for the collection of 30 Fe-Mn crusts from the Atlantis, Great Meteor, Small Hyeres, Irving and Plato seamounts, as well as from the East Azores Fracture Zone. These were the first samples of Fe-Mn crusts studied from these seamounts. The Fe-Mn crusts were analyzed using multiple analytical methods.The crusts are fairly homogeneous, showing typical textures for this type of occurrences. The Fe/Mn ratio, patterns and concentrations in rare earth elements, and the great homogeneity of the crusts lead to the conclusion that they have a hydrogenetic origin, precipitating directly from seawater. Although the content in Fe and Mn of the crusts is consistent with data available for the Atlantic, the mean concentration of Co is comparable to the average values for the Pacific. Cu and Ni show lower values than the ones known for the Pacific."

Sep 1, 2014

At the end of a century of mining education in South Africa, it is appropriate to reflect on the past, take stock of the present and ponder the future of mining education. While it is likely that changes in the mining industry will generate an increased demand for mining graduates, the number of suitably qualified applicants to study mining is worryingly small. While good progress has been made in unifying the educational system that previously provided schooling on a racially separate basis, it appears that a decade or more will be required to raise competency levels in mathematics, science and English, and this paper describes the process as it affects mining engineering programs. It also describes the initiatives currently being undertaken by the University of the Witwatersrand and the mining industry to ensure that the South African industry receives an adequate flow of well-qualified mining graduates, despite more than 70% of the intake coming from severely disadvantaged educational backgrounds.

Jan 1, 1999

By J. R. Hamke

THE WILLISTON basin is the largest known sedimentary basin on the North. American continent. Two-thirds of this large basin lies within the United States in Montana, North Dakota, and South Dakota. Less than 10 years after the first commercial oil discovery in North Dakota in 1951, the petroleum became one of the largest industries in the three-state area. Crude petroleum is now the most valuable mineral resource in the area. In 1960, the basin produced 39 million barrels of worth $100 million at the wellhead. Most of the 137 oil pools covered to date are in Paleozoic carbonates at depths ranging from 3,000 to 13,000 feet. The major producing fields, centered on the Cedar Creek anticline in Montana and the Nesson anticline in North Dakota, produce from depths below 6,000 feet. This report presents descriptions of all phases of the Williston basin petroleum industry, including leasing, exploration, geology, drilling, production, transportation, and refining. Engineering, physical, and production data, maps, and crude petroleum analyses for 137 separate oil pools are included.

Jan 1, 1966

By T. A. Muhlare

"Large quantities of slag are produced every year and dumped on slag heaps around the world, posing a potential environmental threat due to contained heavy metals content. Slags are waste minerals produced during furnace smelting of minerals. The contained values of base metals may be released into the environment under natural weathering conditions polluting ground and underground water. Copper losses into slag are a continuous problem in pyrometallurgical smelting operations. Due to shortage of ore concentrate, various mining operations have initiated the recovery of copper from dumped slag. The typical process uses crushing, milling and flotation. These operations create excessive liner wear rates during crushing and milling because the bond work index of copper slag is 22 kWh/t and this is considered a very hard slag. The process also has reduced flotation recoveries and requires high flotation reagent consumption. The present work shows that digestion of the milled copper slag slurry with concentrated sulphuric acid at a temperature of 250oC forms a solid cake and leaching of the solid cake with water is a possible option. However, the consumption of sulphuric acid can have a considerable cost on the recovery process. This can be limited by producing a leach residue containing gypsum and silicate materials as amorphous silica which are suitable for use as an additive for Portland cement. Laboratory results show that 90% copper recoveries can be achieved. The leaching is conducted to prevent silica gel formation and iron co-extraction. Leaching is optimum if silica gel-free solutions and good filterable residue are obtained. INTRODUCTION Slag is a waste by-product of smelting and converting operations in metallurgical plants. Both smelting and converting operations are aimed at iron separation from base metal sulphides in non-ferrous metallurgy. The iron sulphide component of the ore or concentrate is oxidized to iron oxide at higher temperatures in the molten form, and then fluxed with silica and other oxide rock minerals to produce fayalite (2FeO•SiO2) slag (Schlesinger et al., 2011). Slags are generally deposited on dumps and considered to be unreactive materials. Smelter copper slag contains significant concentrations of several potentially toxic elements, including arsenic, lead, cadmium, barium, zinc and copper. These elements can be released into the environment under natural weathering conditions and cause pollution of soils, surface waters and groundwater (David, 1998)."

Jan 1, 2015

By I. O. Ojala

Detailed knowledge of velocity-depth trends is essential for constructing well-to seismic ties, determining background velocity and generating synthetic seismic traces for interpreting seismic amplitudes in terms of porosity, lithology and pore fluid type. The acoustic properties of shales are of particular importance in the exploration setting as shales constitute more than 80% of sediments and rocks in siliclastic environments. Seismic and sonic log data may be used for estimating overpressure in shales in order to maintain borehole stability during drilling. In addition, velocities in shales can be used for predicting its mechanical properties and hence, borehole collapse. Despite of the apparent importance of understanding shale acoustics, sonic logs in shales are frequently unavailable or unreliable especially for older wells. Hence, it is essential to compute pseudo-velocity logs from other available information. This can be accomplished by using empirical relationships or rock physics transforms. In this study we have compared the predictive power of resistivity (Faust 1951, Hubert 2008) and porosity based models (Wyllie 1956, Holt & Fjær 2003) for computing synthetic P-wave velocity logs using wireline log data from mudstone intervals at three North Sea wells. The wells 6507/2-1, 6507/2-2 and 6507/2-1 are located at the Haltenbanken area at the Norwegian Sea. The wells targeted hydrocarbon potential at the upper Cretaceous and lower Tertiary sandstone sequences. The sandstone beds are overlain by thick Tertiary and Cretaceous sequences of mudstones. Since our primary goal is to model acoustic velocities in shale, we used wireline data from the Nordland (NL), Rogaland (RL) and Hordaland (HL) groups that are mainly composed of mudstone. The mudstone beds were identified from the well log data by using natural gamma log, sonic and resistivity data as well as information from the Norwegian Petroleum Directorate website. The volume of shale was estimated from the natural gamma log and the data points with values higher than 0.65 were discarded. Similarly, the data points with shale volume less than 40 % were discarded. Furthermore, exceptionally high resistivity values amounting to more than 6 Ohm m were not included in the analysis. Porosities were determined from the density log assuming 2.7 and 1.05 g/cm3 for matrix and fluid densities, respectively. The depth that was used for calculating Vp from Faust (1953) was the depth below mudline in order to the compare of well data from wells that have been drilled at different depths (Hubert 2008).

May 1, 2009

A series of electron beam, cold hearth, single melt Ti-6Al-4V plates (nominally 2.5 cm thick) impacted by 2cm diameter, 4340 steel projectiles (with 54g nominal mass) at velocities ranging from 0.633 to 1.027 km/s were sectioned along the impact axis and examined by optical metallography to characterize the formation, growth, and microstructure of adiabatic shear bands. Near ballistic limit velocities, the shear bands propagate towards the rear of the target where they coalesce and grow to provide a cylindrical solid state flow regime for the plug volume.

Jan 1, 2006

By J. A. Luckmann

"SynopsisThe purpose of this paper is to introduce an innovative approach to risk management in surface mining operations, namely, positive risk. Traditionally, risk management focused on mitigating losses (negative). Positive risk, on the contrary, reverses the approach and focuses on exploiting a project’s inherent benefits (positive).The inability to accurately determine project objectives during the project planning phase and the failure to achieve those objectives during the execution phase is a major problem for any project management in the mining environment.The advance of computer aided design models for mine planning enables mining engineers to examine various options within a very short time. Employing positive risk management combined with drivers-based risk management when evaluating these options provides an ideal opportunity to investigate areas for improving the mining project’s profits. Furthermore, harnessing positive risk returns during the planning phase contributes immensely to the successful achievement of project objectives.Mining has inherent business risks, which can appear overwhelming when considering the risks associated with a mining project schedule, cost, and safety or resources, etc. The question is – how to manage risks in a surface mining environment, and what process methodologies, work methods, processes, and standards should be used when considering the surface mining risks. Applying the principles of positive risk management to manage surface mining risks is not only relevant, but definitely beneficial to mining projects and to the mining industry as a whole.It would be beneficial for risk managers and risk professionals to understand the roles of positive risk ‘drivers’, also known as ‘propitious attractors’. Identifying, analysing, estimating, and understanding the propitious attractors, their behaviour and their influence on project risk events helps considerably during the planning and execution phases. The theoretical and practical knowledge of both sides of the risk – the downside risk (negative risk) and upside risk (positive risk) – can add substantial value to any organization when downside risk is adequately mitigated and upside risk is beneficially exploited."

Jan 1, 2015

By F. Block, K. Kohli

Outcrop barrier pillars serve to keep mine personnel and the public safe from sudden uncontrolled flows of water accumulated in active and abandoned underground mine workings. When an outcrop barrier fails, the result is an outbreak of water to the surface and is termed as blowout. Mine blowouts are associated with above-drainage mines and can occur through the coal outcrop and sealed portals. A blowout is often catastrophic, a threat to the people on the surface living or working in the path of a potentially large flood. In addition, blowouts can destroy homes, cause landslides and severe erosion and release pollution and acid mine drainage. This paper provides guidance on the planning, design, evaluation and inspection of barriers to address the problem of mine blowouts associated with above-drainage coal mines.

Jan 1, 2007

The only economically significant deposit of dolomite in New Zealand is at Mount Burnett, in north-west Nelson. The dolomite, associated with marbles and schists, is complexly deformed, and is of Paleozoic age.A very large quantity is present, although the recoverable amount is to some extent limited by the difficult terrain.Physically the quality of the dolomite is excellent. It is a tough, durable, fine grained rock. Chemically it is a little more variable. The range and frequency o~ the more important impurities are illustrated by hlstograms, as is the "dolomite factor"-a measure of the amount of the mineral dolomite in the rock. lbe dolomite factor averages 84 per cent, the remainder of the rock consisting largely of calcite. Quarrying, milling, production, and uses are described. In 1966 production reached 13,250 tons.

Jan 1, 1969

By David A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. 80122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available. Personnel involved in the investigation include J.R. Wait (Principal Investigator), D.A. Hill (Co-Principal Investigator), K.P. Spies, A.Q. Howard, and Lana Slusher (Administrative Assistant).

Jan 1, 1974

By A. Wright, P. Lacombe, R. del Villar, D. Hodouin, C. Sepulveda

"The data acquisition from industrial plants is a fundamental step for process modelling in process optimization, process analysis and automatic control.The introduction, some years ago, of modern distributed control and data acquisition systems in concentrators imposes a new approach in designing experimental schemes for data acquisition campaigns and new criteria for the treatment of the obtained discrete information.This paper presents the methodology applied to sample a zinc flotation circuit at Les Mines Selbaie, Joutel, PQ. Values of 85 process variables were obtained form the Distributed Control and Data Acquisition System (Bailey Network 90) and transferred to the DOS environment. Another 11 variables (flowrates and valve positions) were directly sampled using an IBM-PC compatible computer equipped with a data acquisition card and a signal processing circuit.All variables, under the vector form, were processed in the PC-MATLAB environment to either filter or eliminate the non-linear disturbances and noises, producing useful data for model development. The filtering algorithms are also presented.INTRODUCTIONProcess control does not need to be justified. Whether manual or automatic, any processing plant requires some form of control to accomplish its main objectives: a good quality product and a target throughput. Process control of mineral processing plants has steadily evolved from manual control, where the operator skills and/or experience play an important role, to some level of automatic control, usually considered better, as less human subjectivity is involved, at least when actions have to be taken.The design of these control systems requires the knowledge of the dynamics of the process it is deemed to control. Process modelling is therefore an essential step in the assessment and the design of a control strategy. The choice of model will depend on the available resources and manpower."

Jan 1, 1991

By David L. Holt

It is well-established that hydrostatic pressure distribution is hardly achieved during uniaxial compaction of powders. All the previous investigations1-4 give consistent results and this variation is attributed to the die-wall friction. The conclusions are based on measurements of the density of very small portions of the compact. Although the analysis of the density or the strain distribution in the compact is very helpful in obtaining information about the stress distribution within a powder compact, it does not describe the problem from a more fundamental point of view. The densification in metal powder compacts takes place chiefly by plastic deformation (ignoring particle rearrangement) at the points of contact of the powder particles. The onset of yielding and subsequent growth of the contact areas (for spherical powders) take place fixed by a constant stress equal to three times the yield stress in tension or compression,5-7 assuming little or no work hardening. Therefore, by deforming spherical powders in the die and measuring the contact areas on each particle, the load at each contact point can be determined. In the present investigation, this was done by hot-pressing uniform spheres of lead, K-Monel, and sapphire. The details of the experiment have been described elsewhere.' The spheres were studied for the size and the number of contact points on each particle using a specially designed goniometer. It was found that the deformed faces that were approximately normal to the direction of pressing were about 2.2 times larger than those parallel to the direction of pressing. Fig. 1 shows the typical deformed sphere. A detailed study showed that the mean value of the contact areas on each sphere was within 5 pct for all the spheres in the die (ignoring those touching the die walls and the top and bottom of the die).' The spheres touching the die walls and the top and bottom of the die were found to have larger contact areas (8 to 10 pct) which indicates higher pressures in these regions of the compact and thus higher compact densities in these regions. These results show that density distribution calculated from such an experiment will give results consistent with the previous investigators. It is concluded, therefore, that the pressure distribution in the die is better understood by studying contact areas on each particle. 'R. Kamm, M. A. Steinberg, and J. Wulff: Trans. TMS-AIME, 1947, vol. 171, p. 439. 'Pol Duwez and Leo Zwell: I. Metals, 1949, vol. 1, p. 137. 'G. C. Kucynski and I. Zaplatynskyj: Trans. TMS-AIIME, 1956, vol. 206, p. 215. 'R. P. Seelig and J. Wulff: Trans. TMS-AIME, 1946, vol. 166, p. 492. 'H. Hencky: Z. Angew. Math. Mech., 1923, vol. 3, p. 241. "J. Ishlinsky: I. Appl. Math. Mech. USSR, 1944, vol. 8, p. 233. 'D. Tabor: Proc. Roy. Soc. (London), Ser. A, 1948, vol. 192, p. 247. 'Ashok K. Kakar and A. C. D. Chaklader: 1. Appl. Phys., 1967, vol. 38, p. 3223. Superplasticity in 60Zn-40Al David L. Holt THE occurrence of superplasticity in Al-Zn alloys is of interest because of its possible industrial exploitation.' The eutectoid composition (78Zn-22A1) has been the most extensively studied;'-= neck resistant flow and high strain rate sensitivity of flow stress (characteristic of superplasticity) are associated with a micron-size grain conferred on the alloy by an homo-genization and quench.5'6 Compositions away from the eutectoid have received comparatively little attention, especially from the viewpoint of relating the structural

Jan 1, 1969

China has made great progress in thick coal seam mining, commonly characterized by longwall top-coal caving mining and single-pass longwall mining with a large cutting height. At present, the maximum mining thickness of longwall top-coal caving reaches 20 m while that of single-pass longwall mining approaches 8.8 m. The top-coal caving–related technologies have significantly improved the mining efficiency of thick coal seams and have also made a great contribution to the centralized underground mining of coal. Thus, the number of underground coal mines is greatly reduced in China. However, due to the increase of the mining height and the changes in mining operations, the overburden movement caused by the mining of thick coal seams is more intense, and the influence scope is larger, which brings a series of new problems on ground control of longwall faces. In order to enhance ground control and improve the mining efficiency of thick coal seams

Jul 28, 2020