Search Documents

By Galyn Rippentropp, Finn Erik Overlie

INTRODUCTION The wet shotcreting system utilizing steelfiber microsilica shotcrete with remote controlled equipment (The Robocon System) was developed in Norway 7-8 years ago. Norway was the natural origin for this system due to several factors. Almost 30% of all underground hydro-power stations in the world are located here. These projects created a need for high productivity shotcreting rigs for the rock support work in the caverns and in the connecting tunnels. During the period of 1976-1980, more than 1000 miles of tunnels were completed in Norway. Secondly, the utilization of microsilica in concrete was also developed in Norway due to a concentration of the world's ferroalloy p ants there. Robocon has presently placed approximately 110,000 m (150,000 cu. yds.) of this superior shotcrete, and has consequently an extensive experience in the shotcreting method. During a relatively short period of time (1975-1980), Robocon had a change from hand-operated, dry-process shotcrete to remote-controlled, wet-process shotcreting, because of improved productivity, reduced rebound, safer and cleaner working conditions. The introduction of microsilica and water-reducing admixture made it possible to produce wet-process shotcrete of high strength.

Jan 1, 1987

By Han Xuanjiang

Through whole analysis of static testing piles information of a teaching building, this paper put for ward that when the ratioes of unload rebound amount to residual deformation and to total settlement reach the maximum, the testing load is selected as allowable capacity of single pile by camparing with the settlement in the practical engineering, it is proved that this method fits to practice, for other several projects, its also available. Therefore non-destructive testing pile method was improved, so all the tested piles can be reused as engineering piles.

Jan 1, 1991

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By U. B. Kodukula

Attempts are made to evaluate the feasibility of using a water-injection cyclone for the concentration of iron ore fines. The separation characteristics of clay fines, containing large amounts of alumina and silica, from the iron values are discussed. The effects of critical variables, such as injection water rate, truncated cone diameter, spigot opening and vortex finder diameter, on the performance of a water-injection cyclone in terms of iron, alumina and silica grades; iron recoveries; and alumina and silica rejections are discussed. A set of 16 full-factorial experiments (24) was carried out to gain an understanding of the individual and interaction effects of the variables. The results indicate that classifying iron ore fines containing 63.0% iron, 2.5% alumina and 3.5% silica through a water-injection cyclone can produce concentrates with iron grades greater than 66.0% and alumina and silica contents less than 1.5% and 2.0%, respectively, at different study conditions. The achievable iron recovery values are greater than 88%, and alumina and silica rejections are more than 80% and 50%, respectively, within the specific study conditions. While the truncated cone diameter, injection water rate and spigot diameter influences the alumina rejection to a considerable extent, it is mostly influenced by the vortex finder diameter. The iron recovery and silica rejection values are mostly influenced by spigot diameter and truncated cone diameter. The effect of injection water on the concentration characteristics depend on the prevalent truncated cone diameter and spigot diameter conditions.

Jan 1, 2008

By Albert L. Toenges

[During the past few years there has beer trend away from locomotive haulage of coal from the loading point to the preparation plant of bituminous-coal strip, miner to motorized. haulage. The question has arisen whether this is always economical, and the purposes of this investigation is to determine, if possible the economic limit for motorized haulage. The operators of strip coal mines and of open-pit ore mines have shown great interest in this problem, and it is thought that the findings of this investigation will. Provo helpful to them.]

Jan 1, 1938

By Jim Mikelait

Overview ?? Why do we need security? ?? Needs assessment ?? Elements to any security system ?? Protect, Detect, Alert, esponse ?? Electronic Security System Criteria ?? Advantages and Limitations of Various Security Options ?? Internal measures to protect against potentially harmful employees ?? How can technology improve my business?

Jan 1, 2006

By J. C. Kingston

Introduction The sliding-form method of erecting concrete structures was first devised and used in the early part of this century by the Sante Fe Railroad Company for the erection of a grain elevator at Santa Fe, New Mexico. A somewhat related principle has been employed for a number of years in shaft lining work and, to our knowledge, was perfected in Butte, Montana, but until the building of the concrete headframe at the Jeffrey mine of the Canadian Johns-Manville Company, Ltd., at Asbestos, Que., the method, as applied to surface structures, was quite foreign to the mining industry in Canada. The current shortage and cost of structural steel shapes has no doubt contributed more than any other single factor to the investigations that have led to the use of reinforced concrete as a headframe building material. Mining men in western Quebec and northern Ontario have shown a great deal of interest in the design and construction of the headframe at the East Sullivan mine in Bourlamaque township, Que., and we have had many queries regarding the methods used and, in particular, for an explanation of the sliding-form principle. This article is written in an attempt to set forth the conditions which were to be met; to explain the construction methods used, and to discuss the economy of concrete headframes as compared with the conventional steel structures with which the mining fraternity is familiar.

Jan 1, 1949

By Sam S. Taylor

[The discovery of many oil fields in Illinois since 1936, and their rapid development have brought the problem of brine disposal to the foreground in that State. The ultimate magnitude of the problem is not yet known, but already it is treat enough to warrant technical investigation. The Bureau of Mines, therefore, has made a general survey of the methods of handling oil-field b brines in Illinois rend has studied in detail three subsurface disposal systems.]

Jan 1, 1940

Precast prestressed concrete piles designed to be end-bearing in a sand stratum at Drax Power Station met with extremely variable resistance during driving. Some piles came to virtual refusal almost immediately on entering the sand whereas others were driven to considerable penetration with very low resistance. Redriving and load tests on piles experiencing low resistance on initial drive showed that take up in strength occurred over a relatively short period of time. Investigations involving the use of pneumatic piezometers revealed the development of significant excess pore pressures during driving. Samples from boreholes showed that piles met the least resistance when the sand had a high silt content. Comparison with the original site investigation data demonstrated the difficulties in predicting detailed pile behaviour. The varied behaviour could not be related to the original borehole logs or to SPT or static cone penetrometer results. The factors controlling pile driving behaviour were essentially geological and could only be explained with reference to local soil grading.

Jan 1, 1989

Ecuador a gross domestic product (GDP) grew 8% despite a slowdown in production and sales of petroleum, the dominant economic sector. Crude petroleum exports, which amounted to about 35% of total exports in 1977, were valued et $484 million,2 a decrease of 14% from 1976 values. Petroleum export sales were depressed because foreign buyers were somewhat uncertain that State-owned Corporación Estatal Petrólera Ecuatoriana (CEPE) held legal title to the oil until final settlement with Ecuadorian Gulf Oil Corp. In addition to the legal complication, Ecuador maintained a relatively high export price for oil until late in the year. There was also a shrinkage of traditional U.S, markets owing to the Alaskan pipeline becoming operational and an increased availability of Mexican supplies. The export market was also affected by increased domestic production in Peru and Chile, which lessened their import needs, and the pressure of greater competition from the Middle East in supplying crude oil to Caribbean refineries. About 20.4 million barrels or 40% of Ecuador's total crude exports went to the United States. Only 27 wells were drilled in Ecuador during L977; of these, 16 produced oil, 3 were dry holes, and 8 were suspended. About 31 wells were planned for 1978. Three new oilfields were discovered during 1977; two by CEPE in northeastern Ecuador and one by the Argentine State oil company Yacimientos Petraliferos Fiscales (YPF), operating in Ecuador under a service contract. CEPE's two discoveries tested at 5,000 and 1.450 barrels per day, respectively. The YPF discovery tested at about 1,000 barrels per day. Ecuador altered its position regarding

Jan 1, 1981

By J. Bakken, M. Th. Jonsson, G. Sævarsdottir

A typical three-phase submerged-arc furnace for production of silicon metal and ferrosilicon has arc currents ~100 kA, phase voltages ~100 V and total furnace power ~10 - 60 MW. The arcs burn in gas filled cavities or "craters", where the main atomic components of the plasma mixture are silicon, oxygen and carbon. Two quite different simulation models for high-current AC arcs have been developed: the simple Channel Arc Model (CAM), and the more sophisticated Magneto-Fluid-Dynamic Model (MFD). These models have been described extensively and results reported at INFACON-8 and INFACON-9, respectively. The coupling between the arcs and the AC power source is described by a complete three-phase Electric Circuit Model. Recent numerical modelling studies of industrial AC arcs show that the boundary conditions at the cathode and anode are critical for the simulation results. A novel Cathode/Anode Sub-Model for high-current AC arcs that treats both cathode and anode indicates a completely different cathode behaviour than previously assumed. A cathode spot which serves a high-current electric arc is shown to be dominated by the energy impact from the arc. This leads to lower cathode fall voltage than obtained from previously developed models. The anode fall voltage is negative, as the main function of the potential barrier is to repel plasma electrons. The cathode spot is diffuse in the sense that the arc in fact contracts away from the cathode. Simulation results are compared to measurements on both industrial furnaces and smaller scale pilot furnaces. An important conclusion, supported by our arc studies, is that the arc length in silicon metal and ferrosilicon furnaces does not exceed 15 cm and the arc may burn anywhere on the electrode, not necessarily beneath the electrode tip.

Jan 1, 2004

By Thomas Marcher

Stanford Linear Accelerator Center (SLAC) is located in Menlo Park, CA. In order to allow for enhanced experiments, the current facilities required expansion. Tunnels were excavated through very weak sedimentary rock interspersed with uncemented zones (Ladera Sandstone) employing the principles of the NATM. The overburden var-ied from 10 to 80 feet. The paper addresses the characterization of Ladera Sandstone that can exhibit the properties of dense sand and weak rock. The paper focuses on the challenges that were encountered during the NATM initial support design and the construction phase including the geotechnical instrumentation, monitoring and design verification process in particular the excavation of the junction between access tunnel and the FEH cavern (49 ft wide by 32 ft high).

By C Placzek, E Beattie, K Blake

Channel iron deposits (CID) consist of ferruginous chemical sediments, and are an unusual subset of Phanerozoic ooidal ironstone deposits almost unique to the Pilbara, where they constitute around 19 per cent of the Pilbara’s iron ore exports. These deposits occupy many of the ancestral river channels of the Pilbara region, especially the Robe River palaeochannels, incising and meandering through the Precambrian banded iron formations (BIF) of the Hamersley Group and the underlying Fortescue Volcanics.This paper explores the factors underlying geochemical variation in CID, particularly the chemical properties of goethite. The selected deposits in the western Robe palaeochannel and its tributaries show little or no secondary reworking by later water tables. There is a total absence of aluminosilicate clays with all the deleterious elements such as aluminium and silica. Instead, these are associated with the goethite mineral lattice, either within or adsorbed to the cortices of pelletoids.A thickly vegetated environment, and the presence of the Maddina Volcanics as potential source rocks for these western Robe CID is offered as an explanation for relatively high aluminium in the deposits studied, and, in turn, as the reason most parts of the palaeochannel are preserved as inverted topography.CITATION:Beattie, E, Placzek, C and Blake, K, 2017. Dirty goethite – a geochemical characterisation of some western Robe River channel iron deposits, in Proceedings Iron Ore 2017, pp 489–502 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By N. Simpson

Low carbon 11.5% chromium stainless steels are finding increasing use in industry as square or rectangular tubing material for the construction of structures by welding. During processing, resistively welded circular pipes are bent into square or rectangular shapes. During this process longitudinal cracks can sometimes develop atone of the inner corners of the section. An investigation has shown that the processing of round into square tubing with very sharp corners can cause excessive cold working at the inner corners of the squared tube. This, together with the high tensile residual stresses and a susceptible microstructure due to the presence of grain boundary carbides, can result in brittle cleavage cracking. Measures that can be used to reduce the problem are described.

Jan 1, 2003

By Heiner J. Sander

Stanford University operates the National Research Facility which is located at the Stanford Linear Accelerator Center (SLAC) in Menlo Park, California. In order to improve and allow for enhanced experiments, the current facilities required expansion. A1500 foot long tunnel (20 ft wide by 21 ft high) and a 220 foot long underground cavern (49 ft wide by 32 ft high) were excavated through the Ladera Sandstone formation which is an intermediate geo-material with week rock properties. The overburden between surface and crown of the structures varies from 10 to 80 feet. The underground structures were excavated according to the principles of the NATM (New Austrian Tunnel Method). This paper addresses the challenges that were encountered during the construction phase of the project and how construction issues were resolved mutually by the owner, engineer and contractor. The implementation of geotechnical instrumentation, recorded data and interpretations, soil conditions and behavior encountered during construction are also presented.

Jan 1, 2008

By D. J. Fourie

During the production of pure TiO2for the pigment industry, ilmenite, containing 35?60% TiO2, is reduced to high titania slag, containing 70?95% ?TiO2? and pig iron. The high titania slag produced, consists mainly of titanium in different oxidation states and FeO in equilibrium with liquid iron. To predict the phase and chemical reaction equilibria in a furnace, a suitable solution model is required with accurately determined binary interaction parameters, as slag melts tend to behave very non-ideally. This paper investigates two popular slag models, namely, modified quasi-Chemical (MQC) model and the cell model and provides the binary interaction parameters based on recently published data of the ternary system and critically assessed published unary and binary data. Very few modelling results have been published on the ternary Ti-Fe-O system pertaining to high titanium slags. The solution models, with their regressed interaction parameters, can subsequently be implemented in commercial software of the slag-metal phase equilibria to predict how much and which type of solids will precipitate for a given bulk slag chemistry and operating temperature or, alternatively, above which temperature should a furnace be operated to avoid excessive solids precipitation.

Jan 1, 2005

By N. Kuyucak

"Acid mine drainage (AMD) is one of the most significant environmental challenges facing the mining industry worldwide. It occurs as a result of natural oxidation of sulphide minerals contained in mining wastes at operating and closed/decommissioned mine sites. AMD may adversely impact the surface water and groundwater quality and land use due to its typical low pH, high acidity and elevated concentrations of metals and sulphate content. Once it develops at a mine, its control can be difficult and expensive. If generation of AMD cannot be prevented, it must be collected and treated. Treatment of AMD usually costs more than control of AMD and may be required for many years after mining activities have ceased. Therefore, application of appropriate control methods to the site at the early stage of the mining would be beneficial.Although prevention of AMD is the most desirable option, a cost-effective prevention method is not yet available. The most effective method of control is to minimize penetration of air and water through the waste pile using a cover, either wet (water) or dry (soil), which is placed over the waste pile. Despite their high cost, these covers cannot always completely stop the oxidation process and generation of AMD. Application of more than one option might be required.Early diagnosis of the problem, identification of appropriate prevention/control measures and implementation of these methods to the site would reduce the potential risk of AMD generation. AMD prevention/control measures broadly include use of covers, control of the source, migration of AMD, and treatment. This paper provides an overview of AMD prevention and control options applicable for developing, operating and decommissioned mines."

Jan 1, 2002

By T C. Ooi, L Lu

Owing to ongoing development of new orebodies and changes to existing mining operations, new ore types with distinct mineralogy, porosity and textures are generated as feed for iron and steelmaking. Moreover, further product differentiation occurs as fine ores are increasingly beneficiated to achieve grade. A study was necessary to characterise a suite of iron ore fines in terms of their propensity for formation of quasi-particles and green bed permeability prior to sintering. In this study, two Marra Mamba bedded iron deposit (BID) samples, one Pisolitic channel iron deposit (CID) samples, two dense hematite samples (coarse and fine grained microplaty hematite), one hematite-goethite BID samples and one hematite-goethite bedded/detrital iron deposit (BID-DID) composite sample were investigated. Both Marra Mamba fines and Pisolitic fines exhibit the highest green bed permeability followed closely by hematite-goethite fines, fine microplaty hematite fines, hematite-goethite BID-DID composite fines and coarse microplaty hematite fines at a moderate sintering bed depth of 500 mm. While porous fines generally form better quasi-particles upon granulation than dense fines, the amount of moisture addition increased due to the moisture saturation of the porous fines. As sinter strands become ever larger and deeper, it was necessary to examine the granulation performance of these ore types at a range of bed depths ranging from 300 to 900 mm. On average, the green bed permeability achieved by different ore types, decreased by approximately 7.5 - 9 Japanese Permeability Unit (JPU) as the bed height was increased from 500 mm to 900 mm. In order mitigate the effect of lower bed permeability of the deeper beds, small additions of hydrated lime were investigated as a binding agent to facilitate the formation of strong micro-pellets. With the addition of three per cent hydrated lime, equivalent to approximately 2.3 per cent burnt lime, the majority of fines achieved adequate permeability for deeper bed sintering, with the exception of coarse microplaty hematite fines. In simulated coastal steelmaking sinter blends, it was found that the overall granulation performance of the blend is contributed to by individual fines constituting the blend. Therefore fines possessing favourable granulating properties impart better granulation to the blend as a whole.CITATION:Ooi, T C and Lu, L, 2013. Effects of ore type and binder addition on the formation of quasi-particles and green bed permeability at different sintering bed depths, in Proceedings Iron Ore 2013 , pp 459-466 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Michael Arnold, Robert Bachus, Michael Bracher, Jamey Rosen, Robert Roff

"For a high hazard USACE facility, the Center Hill Dam in Tennessee, several disparate streams of data were compiled into a single geospatial and relational enterprise data management system to store, analyze, visualize and distribute the data collected during installation of a deep cutoff wall. These data streams included historical drawings and pre-construction plans and grouting records; geological data from boreholes; attributes of barrier wall elements; element verticality data analyzed from multiple measurement methods; and concrete field and laboratory analytical data. A previously developed data management system developed by the authors, WallTracker, was extensively modified to also include manually collected and real-time measurements from several types of dam monitoring instruments. The system now uses enterprise database technologies with Geographical Information Systems capabilities to manage and relate these data streams into a common platform and allows access to the raw and interpreted data via web and desktop-based interactive tools, including interactive map and cross-sectional viewers and other graphical and tabular reporting tools. One of the primary benefits of this system is the neartransparent interaction that is possible with the Nashville District of USACE on the project. These techniques can now be effectively incorporated into systems that address the unique construction and data management tracking requirements for dams, dikes, and levees.IntroductionThe Center Hill Dam rehabilitation, as with other deep foundation installations, requires the contractor to collect a substantial amount of information over the course of the project, both for internal quality control of construction progress and methods, and for demonstrating compliance with owner specifications. This paper discusses techniques used at Center Hill Dam for consolidating, visualizing and analyzing construction and instrumentation data using relational database and Geographic Information Systems (GIS) technology, collectively referred to as an Information Management System (IMS).The remainder of this paper presents the needs and objectives of the IMS, the components and data flows involved, the capabilities and user interfaces of the systems, and the benefits for the end users."

Jan 1, 2017

By D. B. Stewart

In the past few years, much effort has been spent in elucidating the impact of diesel engines on the mine environment. This paper summarizes diesel fundamentals , exhaust emissions and typical tailpipe concentrations. Mine sampling results and an evaluation of exhaust treatment systems are discussed. A review of changes in pollutant concentrations between the tailpipe and the mine exit is made and suggestions are given to reduce operator exposure to diesel contaminants.

Jan 1, 1978