Search Documents

By H. M. Morse

This report on oil and gas development in Mississippi covers the period from Jan. I, 1944, to Dec. 31, 1944: Salt Domes During the year six salt domes were drilled for sulphur, but no commercial sulphur deposits were found. One salt dome, the Bruinsburg, in Claiborne County, has produced gas- at 935 to 940 ft' in Moody's Branch marl. The Stringer salt dome in Smith County and the Ruth salt dome in Lincoln County both had a slight showing of heavy oil. Other salt domes have been dry. In addition to the Bruinsburg dome, the Allen salt dome, in Copiah County, and the Richton salt dome, in Perry County, were discovered in 1944; also the Sumrall dome, in Covington County. New Oil Fields Baxtemille Oil Field.—The Baxterville oil field was discoveredby the Gulf Refining Co, in sec. 7, T. I N., R. 16 W., Lamar County. At the end of the year this field had one oil well, with two active operations. Production for 1944 was 1047 bbl. of oil. GwinvilLe Field.—Gwinville field was discovered by S. W. Richardson, in sec. 24, T. 9 N., R. 19 W., Jefferson Davis County. This discovery well was a gas-distillate well, the oil being crystal clear. At the end of 1944 there were two gas wells and one oil well in the field. The oil well is approximately 2 1/2-miles from the gas- distillate wells. Gas production was 55,801 M cu. ft. and the distillate production was 2644 barrels. Heidelberg Oil Field.— The Gulf Refining Co. discovered the Heidelberg field in sec. 30, T. I N., R. 13 E., Jasper County, in January 1944. This field has by far exceeded the other 1943 and 1944 discoveries, having approximately 56 oil wells, 7 dry holes, and 10 active wells at the end of the year. Production to Jan. I, 1945 was 1,441,192 bbl. of oil. Mallalieu Oil Field.—The california Company discovered the Mallalieu oil field in set. 10, T. 7 N., R. 8 E,, Licoln. County. At the end of the year there was one well in the field with three active operations. Production was 32,303 bbl. of oil. Old Oil Fields Brookhaven Oil Field, in Lincoln County, has one oil well, which produced 2590 bbl. of oil during 1944. CarY Oil Field, Sharkey County1 has only one producing well, which produced 11,818 bbl- of oil during the Year- In Cranfield Oil Field, dams County, II oil wells and two gas-distillate wells were drilled in 1944 and there were five active wells on Dee. 31, 1944- The total production for the Year was 5251422 bbl-of oil. The gravity of the oil is 40" to 54.9'- In Eucutta Oil Field1 Wayne County1 34 oil wells were completed during 1944. There were five dry holes and six active wells at the end of the year.. The field produced 454,332 bbl. of all d the average gravity is 25" Flora Oil Field, Madison County, pro-

Jan 1, 1945

By G. Hileman

At present there are three fields in commercial exploitation in the Argentine. In order of production they are: (1) Comodoro Rivadavia, (2) Salta, (3) Plaza Huincul. Comodoro Rivadavia.—This field is on the coast of the Territory of Chubut in the southern part of the republic. It is being developed and exploited by Yacimientos Petroliferos Fiscales, the government oil entity, and five private companies. The immediate coastal portion of the field, which embraces the original discovery area, is almost completely developed. This is especially true of the original government reserve and one private property. The Y.P.F. has extended its explorations and developments westward to Escalante, 27 km. distant on the state railway. This extension has been the most active and prolific section of the field for the past three years. The government has also continued its exploration drilling in the region lying south of Colonia Sarmiento and east of the Rio Senguer. Private companies have not been able to extend their operations beyond the claims they had in process of acquisition in 1924, when the government reserve areas were established. The Y.P.F. is the major producer of the field and employs modern methods and appliances. Practically all its drilling and pumping operations are electrically operated, from a central power plant. In view of t'he scarcity of water supplies, this facilitates operations and is an economic factor of considerable importance.

Jan 1, 1934

By J. V. Vogel

Jan 1, 1969

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals-pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent W03 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent WO3, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By Stephen E. Merritt, T. Carl Shelton

Surveying and mapping are used to locate and visually portray objects, lines, or areas in relation to a reference point or line. The actual making of the measurements to locate the objects and points falls under surveying while mapping is concerned with putting the survey information into a graphical form. Generally, the type or class of proposed survey depends on the precision required. Some surveys may need only approximate measurements which can be obtained by simply pacing or by using an ordinary measuring tape; others may require much accuracy, thus calling for the use of an engineer's transit or theodolite along with a graduated steel tape for horizontal measurements, or a level and a graduated rod for measuring vertical distances. Mapping is likewise dependent on accuracy requirements. For example, a general layout showing the relative position of surface facilities may not call for a large scale of dimension or great precision whereas for detailed work, a large scale plus care in plotting points and drawing lines and curves are important factors. SURVEYING METHODS There are many kinds or types of surveying methods. Some examples include: land surveying for determining boundaries of land areas ; route surveying for locating roads, highways, right-of-ways, and haulways; city surveying for laying out lots, streets, and alleys ; and mining surveying for projecting mine openings and locating mining operations. There are other types of surveying than those named, but in general, the type of method to be used will depend on the purpose for which the survey is to be made.

Jan 1, 1973

By G. B. WATERHOUSE

THE year 1929 was exceedingly busy and prosperous for the iron and steel industry in the United States. The lake shipments of ore were approximately 65,000,000 tons, steel ingots produced were about 57,000,000 tons. Plants were very active. operating for many months well over their rated capacity, slowing down during the last quarter following the severe break in the stock market. The ore tonnage mentioned above was the greatest ever shipped by lake from the Lake Superior region. The trend at the ore mines has been to supplement manual labor by mechanical appliances as much as possible. Mining methods have been greatly improved along the lines of safety as well as to increase the percentage of ore recovery. Crushing and grading of iron ores continued to gain in popularity inasmuch as remarkable blast-furnace operations and records were obtained with sizing and uniformity of raw materials. Progress was made along other lines. The Bradley process for the separation of manganese osicle and iron oside from siliceous manganiferous iron ore was cleuelopecl; also considerable work was clone on a process for the beneficiation of the Cuban laterite ores. Sintering of ores and concentrates increased in popularity. A new analytical method for the deter- mination of sulfur in iron ore was worked out which reduced the time required appreciably. The ore re- serves of the Lake Superior district continued to receive considerable attention and played an important part in the recent mergers which have taken place in the iron ancl steel industry.

Jan 1, 1930

By A. R. Marder

Fe-C alloys have been investigated at temperatures below the eutectoid transformation to determine whether the superplasticity phenomenon exists for these materials. As a result of void formation at the carbide-ferrite interfaces that led to void coalescence and premature failure, the large elongations characteristic of superplustic matem'als did not develop. It had generally been assumed that the conditions for obtaining superplasticity include: a) T/Tm =0.5, b) a strain rate sensitivity of the flow stress that results in m s 0.3, and c) fine-grain structure. Although superphsticity was not observed in the alloys studied, stress-strain rate measurements indicated that an additional condition for the existence of superplasticitv in Fe-C allovs is that the fine-wain structure be equiaxed in agveement with previous results on Zn-Al al1oys. MANY investigations have been made on the hot deformation of iron-base alloys in order to obtain an understanding of the variables that may affect high-temperature strength and ductility.'-6 However, only a few papers have studied the effect of carbon content on the high-temperature properties of iron-base alloys. Peretayat'ko and Zaikov and Wallquist and carlen4 studied the effect of carbon on strength in the y temperature range, and recently Robbins, Shepard, and sherby6 studied the influence of carbon on the torsional behavior of iron in the a and cu-plus-cemen-tite temperature ranges. In addition to studying hot deformation behavior, current investigations have also been concerned with the phenomenon of superplasticity in nonferrous materials, and, in particular, ferrous alloys. Superplasticity is identified by the increased resistance to necking that results from a high strain rate sensitivity of the flow tress. ackofenr proposed the strain rate hardening coefficient m = d log a/d log e as a measure of strain rate sensitivity and showed that m must be "-0.3 for superplasticity to exist. In addition, a fine-grained microstrcture,- a eutectic or eutectoid ornosition,- and a test temperature in the creep range (TITm > 0.5)" have also been advanced as necessary conditions for superplasticity. Although many workers""23 investigated superplasticity associated with the allotropic transformation in iron and the eutectoid transformation in steel, and recently chadler " and orrison have studied superplasticity in the a - y phase region, no one has measured the superplastic effect in the a + cementite temperature region. Therefore, the purpose of this investiga- tion was to determine the effect of carbon content, microstructure, and test temperature on the strain rate sensitivity of Fe-C alloys at temperatures below the eulectoid transformation. EXPERIMENTAL PROCEDURE Fe-C alloys with carbon contents of 0.2, 0.4, 0.6, 0.8, and 1.0 wt pct were prepared as 100 lb 54 in. ingots by vacuum-induction melting. The compositions are listed in Table I. All the ingots were soaked at 2100°F for 2 hr prior to rolling to 4 in. plate. The minimum finishing temperature for rolling was 1800°F. The plate was sheared in 10-in. lengths and tensile bars were rough-machined prior to heat treatment. The samples were heat-treated according to the schedule in Table I1 in order to obtain a fine-grained microstructure consisting of finely dispersed carbides in a matrix of small ferrite grains. All the tensile specimens were heat-treated prior to finish machining, and tensile testing was accomplished on an Instron machine in conjunction with a clamshell furnace. The buttonhead specimen configuration is shown in Fig. 1. An inert atmosphere, helium, was maintained during testing with a steel tube shroud in a bell jar arrangement. Predried helium was continually purged over the buttonhead specimens and exhausted through ceramic fiber at the bottom of the tube to keep oxidation at a minimum and to prevent

Jan 1, 1970

By A. B. Parsons

LAST YEAR (1934) saw the completion of a ten-year program of reconstruction and modernization of the world's largest lead- smelting plant, that of the ' Broken Hill Associated Smelters Proprietary, at Port Pirie, South Australia, which has a capacity for smelting and refining 220,000 (short) tons of lead per year. It deals with the entire output of lead concentrates from the famous Broken Hill district in Australia, being owned .jointly by the three leading companies: North Broken Hill, Broken Hill South, and the Zinc Corporation. These companies, together with the Sulphide Corporation, are credited with a production of 198,000 tons of lead in 1934. When one says regarding any metallurgical plant that modernization is "completed" he should add "for the moment." Development in the art of metallurgy and in the equipment used never ceases; that which seems close to the last word today is likely to be obsolete in a few years even in a process so well standardized as smelting and refining lead. However, the reconstruction at Port Pirie has altered the procedure materially. More im-

Jan 1, 1935

By AIME AIME

AN IMPORTANT innovation in Alabama in the semi-longwall type of coal mining as applied to low-dipping thin seams has been introduced by the Galloway Coal Co., mining the Mary Lee high-ash seam which averages only 26 in. thick. The property is their Mill Creek mine, near Carbon Hill, Ala., in the Warrior coal field. The results, although not final, indicate that roof conditions can be successfully handled by this method without loss of walls, with a rate of recovery much above that possible with the room-and-pillar method, and at the low production cost necessary for this grade of coal. Double cross-headings are turned off a main haulageway on 60-ft. centers and driven 40 ft. wide with thin chain pillars between. These double entries are turned at 525-ft. intervals, leaving a solid block of coal 440 ft. across; that is, from the outside of one pair of headings to the inside of the next pair is 440 ft. The bottom, which consists of hard fireclay, is taken in these entries 8 ft. wide and 4 ft. deep for head room.

Jan 1, 1934

By Rip Thompson

ALTHOUGH the metallurgical treatment for the Ophir Hill tailings was developed more than 20 years ago and in the interim a vast amount of experimental work was done with later-developed flotation rea-gents, it was found necessary to revert to the original oil reagents and their combina-tions with specific chemical reagents in order to obtain results of economic value. This is of especial interest because in present ore-treatment investigations later-developed flotation reagents are used almost exclusively and the coal-tar deriva-tives, except in certain patented reagents, are virtually neglected. These coal-tar oils and derivatives still have a definite field of application, especially in the treatment of some oxidized ores when modified sulphidi-zation is desirable. The Ophir Hill tailings deposit is in Ophir Canyon, Tooele County, Utah, about 55 miles southwest of Salt Lake City and 25 miles south of the Tooele smelter of the International Smelting and Refining Co. A road good for trucks leads directly from the Ophir mill to the smelter.

Jan 1, 1940

By Persifor Frazer

CONTENTS. PAGE 1. Committee House of Commons Report (1843).......521 2. Clark (1880).............521 3. Schröder and Schertel (1884).... . 521 4. Committee House of Lords Report (1887).......523 5. Vita (1890).............524 6. Irvine (1890-1)............524 i. Cramer (1891)............525 8. Bailey. Cohen. Tatham and Hartog (1891))......525 9. Morrison (1891)............525 10. Brunner (1891)............525 11. Bell (1892).............585 12. Oades (1892).............526 12a. Purcell (1892)............526 13. Sennett (1892)............526 14. Bulier (1892).............526 1.7. Wiesner (1892))...........526 16. Thomson (1892)............530 17. Fletcher (1892)............530 18. Committee Engineers' Club Report (1892).......530 19. Cohen and Hefford (1892)..........531 20. Discussion Soc. Chem. Ind. (1893). ..532 21. Reuss (1893).............532 22. Thomson (1894—5) ...........535 23. Clowes and Feilmann (1895). ...536 24. Callan (1895)...........536 2.5. Wright (1895)............536 25A. Mabery (1895)............536 26. Re- (1896). ..........536 27. Herman (1896)............ 537 28. Cohen and Russell (1896).......... 537 29. Dennstedt and A hrens (1896). ..537 30. Cohen (1897). ...........537 31. Drehschmidt (1897)........... 538 32. Pfeiffer (1898). .........538 33. Fritzche (1898)............ 540 34. Ost and Wehmer (1899)........... 540 35. Donkin (1899). .........541 36. Beilby (1899)............. 643 37. Berthelot (1900)............ 544

Jan 1, 1908

By Donald F. Saunders

Means and relative standard deviations were calculated for eU, eTh, K, and their ratios for aerial gamma-ray spectral data in 29 quadrangles at 1:250,000 scale. Known or suspected uraniferous provinces were characterized by: 1) Higher eU, eTh, and K means (due to generally higher radioelement concentrations); 2) Higher relative standard deviations for eU, eU/eTh, and eU/K (reflecting the presence of local uranium enrichments); and lower mean eU/eTh and eU/K values (showing uranium loss from "average" rocks to form local enrichments). "Uranium favorability indexes," i.e., combinations of the sensitive variables, show an excellent qualitative relationship to known occurences and geologic favorability. Results appear to confirm the existence of long-term crustal uranium provinces formed at the time of emplacement of the oldest known rocks.

Jan 1, 1980

By Robert R. Walden, LeMont West

K ENTUCKY'S first acid-grade fluorspar flotation Kmill, shown in Fig. 1, was placed in operation Aug. 1, 1952, by the Pennsylvania Salt Manufacturing Co. at Mexico, Ky. During 1951 a critical shortage of acid-grade fluorspar developed and it became necessary for the company to produce part of its fluorspar requirements. In 1951 the company purchased the Crider and Lennen metallurgical fluorspar mill and an adjacent stockpile of tailing at Mexico, Ky. The tailing, assaying about 26 pct calcium fluoride, originated from log washer and jig mill concentrators in the area. As the mill did not have a fluorspar dryer or convenient rail facilities, the company leased the Burleson concentrator at Marion, Ky., where these facilities were available. At Marion, Ky., on the Illinois Central Railroad, dry acid-grade fluorspar is transported direct to the company's Calvert City, Ky., hydrofluoric acid plant. The Mexico flotation plant was reconditioned and designed to produce acid-grade fluorspar from the jig tailing stockpile. The new plant flowsheet is shown in Fig. 2. The ore feed, old tailing, which contains 10 pct of waste rock and coarse gravel assaying approximately 8 pct CaF,, is bound together by sticky clay

Jan 1, 1955

Meeting of Mar. 26, 1915.-The following Committee on Nominations was appointed: Fred W. Bradley, Chairman; James F. Kemp, Past President; Frank M. Smith, Chairman Montana Section; R. C. Gemmell, Chairman Utah Section; Frank A. Ross, Chairman Columbia Section; Louis S. Cates, Arthur Thacher. The Committee on Precious and Base Metals and the Committee on . Coal and Coke were appointed, the personnel of which is shown in another part of this Bulletin. The President was authorized to appoint a Committee on Welfare with J. Parke Channing as Chairman. W. P. Cutter, Librarian of the United Engineering Societies' Library, was appointed a representative of the Institute on-the Committee oh Classification of Engineering Knowledge to co-operate with similar committees of other engineering societies. A vote of thanks was extended-to Edward B. Sturgis for his excellent work in arranging for the Annual Dinner. in February, of this year. The suns of $57.30 was appropriated to the New' York Section. It was resolved that in response to the courteous invitation from 36 members of the Institute in Arizona and the neighborhood, the 1916 summer meeting of the Institute be held in Arizona.

Jan 5, 1915

By Roger C. Ilsley

The $2.1 billion Milwaukee Water Pollution Abatement Program (MWAP) requires the construction of several miles of underground openings at depths up to 350 feet for the conveyance and storage of sewage and storm water overflows. The system will include approximately 27km (17 miles) of deep tunnels ranging from 3m (10 f t.) to 9m (30 f t.) in diameter, 26 shafts and a pumping station cavern. The facilities will be located primarily in Silurian Age dolomites of the Niagara Group. The rock is characterized as competent with vertical to sub-vertical orthogonal jointing and predominantly thin shale bedding planes. The site investigation was carried out incrementally, commencing on an area wide basis, becoming site specific as facility plans were developed. To achieve cost savings through uniformity and continuity, a computerized data bank was established. Software was developed during the initial stages of the program for the production of borehole logs, structure contour maps, geologic profiles and summaries of data for statistical evaluations. This paper discusses in general terms the collection, compilation and presentation of data necessary for the characterization of the rock mass.

Jan 1, 1984

Accessions AMERICAN ELECTROCHEMICAL SOCIETY, TRANSACTIONS, vol. 33. Bethlehem, Pa. 1918. AMERICAN ASSOCIATION OF PETROLEUM GEOLOGISTS, BULLETIN, vol. 2. 1918. (Gift of the Association.) AMERICAN YEAR BOOK: 1915. Edit by Francis G. Wickware, New York. 1919. (Gift of D. Appleton & Co.) ANNUAIRE DE LA HOUILLE BLANCHE FRANCAISE. ` By M. Auguste Pawlowski. 2d year. 1918-1919. Paris. (Gift.) BLACK DIAMOND, Vol. 60, Jan.-June, 1918; vol. 61, July-Dec., .1918. (Gift.) Chicago. CANADIAN MINING INSTITUTE, TRANSACTIONS, vol. 21. 1918. Montreal, Quebec. COMPTES-RENDUS DE L'ATHÉNÉE LOUISIANAIS, vol. 4, No. 3. (Gift of Wm. Beer.) EFFICIENCY OF NATURAL GAS AT Low PRESSURES. Abst. of testimony of Samuel S. Wyer before the Corporation Commission of Oklahoma, February 4, 1919. Printed by Empire Gas & Fuel Co., Kansas City, Mo. GEOLOGICAL. INSTITUTION OF THE UNIVERSITY OF UPSALA, BULLETIN. Edit. By Hj. Sjögren. vol. 14, 1917; vol. 15, 1916; vol. 13, pt. 2, 1916. (Gift.) HYDROGENATION OF OILS. Catalyzers and catalysis and the generation of hydrogen and oxygen. By Carleton Ellis. 2d edition. New York. 1919. (Purchase.) INSTITUTE OF METALS, JOURNAL, vol. 26. No. 2. Edited by G. Shaw Scott. London. 1918.

Jan 6, 1919

By A. C. Dorenfeld

In most mineral enterprises, what is the progress, and shift in responsibilities, as the young engineer advances in the corporation? You are all familiar with the normal pattern-in mine production from level boss, to shift boss, to superintendent to manager; in milling from test engineer, to shift boss, to foreman, to superintendent and then manager; in engineering from surveying on to Chief Engineer; and all then aspire to the corporation presidency. Note the shift-from purely technical jobs, say in the first five to ten years in the profession, to administrative positions for 30 to 40 years. What is the average preparation given to mineral engineering students, who can look forward to about 30 years of administrative work? From the catalogs of 21 institutions, offering 36 curricula of four years length, in mining and/or metallurgy, requiring the equivalent of about 150 to 160 semesterhours for graduation, the following results were obtained: Average number of semester hours of economics, 3 hr. Range of requirements, 0 to 8 hr. Thirteen curricula do not require any economics. Accounting and business law, average: 1 semester hr, 26 curricula do not require business law or accounting.

Jan 2, 1955

By WALTER VOIGTLANDER

FOR nearly 100 years wire rope has been fabricated in much the same way. To the great majority of mine superintendents wire rope is just wire rope, little or no semblance of individuality or identifying characteristics. Such an impression was fairly justified until three or four years ago when a practical means was found of performing or preshaping the wires and strands. This discovery permitted a revolutionary change in wire rope manufacture. Instead of merely twisting a number of wires into a strand, then twisting several strands into a complete rope (which twisting would naturally result in great internal strain, thus reducing the resiliency and over-all efficiency of the completed rope), the preformed wires and strands were laid in place without force or twisting. The obvious result was a rope more nearly approximating mechanical perfection. The applied loads are more evenly distributed throughout the component wires and strands, thus reducing unbalanced wire stresses. This results in a higher safety factor. The fact that preformed rope will not unravel when untied at the ends proves the absence of a torsional stress that exists in ordinary rope. A greater useful allowable stress in the wires is therefore possible in actual operating service.

Jan 1, 1926

Meeting of June 26, 1914.-The President was authorized to appoint Advisory Committees to co operate with the United States Bureau of Mines. The President announced the appointment of Edward H. Benjamin and W. C. Ralston as additional members of the Committee on Arrangements for the San Francisco meeting, 1915. H. T. Van Ells and Judd Stewart were appointed to represent the Institute on a joint committee of several technical societies to consider the standardization of graphical methods for the presentation of statistics. The President announced the appointment of H. Foster Bain to succeed Edward H. Benjamin, resigned, on the Committee of Management of the International Engineering Congress, 1915. The Secretary was authorized to issue a new circular advertising the sale of back Transactions and to sell back Transactions, bound in cloth, at a price of $35 for 46 volumes, provided sufficient orders were received to warrant the special binding. The sum of $177.50 was contributed to the San Francisco Local Section. Upon recommendation of the Committee on Membership, 70 Members, 4 Associate Members and 7 Junior Members were elected to their respective classes; there was also one change of status from Junior Member to Member.

Jan 8, 1914

THE Institute assembled on Tuesday evening, October 24th, in the hall of the Franklin Institute, Mr. Frank Firmstone, VicePresident, in the chair. Mr. J. Price Wetherill, of Tremont, Pa., read a paper on An Outline of Anthracite Coal Mining in Schuylkill County, Pa. The paper was discussed by Messrs. Coxe, Rothwell, Heinrich, Harden, and Symons. The second session was held on Thursday evening. Mr. A. L. Holley, Chairman of the International Committee, appointed by the Institute to consider the nomenclature of iron and steel, offered the following report of the committee, signed by all the members: WHEREAS, The recent production of soft, cast, malleable compounds of iron by the Bessemer, the Siemens-Martin, and the crucible steel processes appears to demand a new nomenclature of iron compounds, for the following reasons: 1st. The term "steel," by which these soft products are commercially and professionally designated in England and in the United States, does not completely distinguish them from previously existing "steel which would harden and temper. 2d. A nomenclature recognized in all languages seems desirable, as well for commercial as for scientific purposes, especially as lawsuits, already commenced, depend on the meaning of the term " steel." 3d. Although homogeneity, due to fusion, is usually recognized, and is by this committee recognized as the most definite characteristic of both hard and soft steel, this quality may be equally well expressed in other terms, thus leaving the old term, " steel," to define the malleable compounds of iron, which will harden and temper. Therefore, resolved, That this committee recommends the following nomenclature : 1. That all malleable compounds of iron with its ordinary ingredients, which are aggregated from pasty masses, or from piles, or from any forms of iron not in a fluid state, and which will not sensibly harden and temper, and which generally resemble what is called " wrought iron," shall be called Weld Iron (German, Schweisseisen; French, fer soudé). 2. That such compounds, when they will from any cause harden and temper, and which resemble what is now called puddled steel," shall be called Weld Steel (German, Schweiss stahl; French, acier soudé).