Search Documents

By P M. Ashley, M T. Costelloe

The Mary Kathleen tailings storage facility (TSF) contains 7.1 Mt of uranium mill tailings. This waste repository was rehabilitated in the mid-1980s using a multibarrier dry cover. At the time of mine closure, it was predicted that acid mine drainage (AMD) generation would not eventuate and that uranium, heavy metals and radionuclides would be adsorbed within the tailings and not seep from the TSF into the environment. This study reports on the environmental status of the TSF. Gamma-ray measurements indicate an intact dry cover of the waste repository. However, seepage (~0.5 L s-1) of acid (pH 5.71), saline (0.31 per cent), high conductivity (8.8 mS cm-1), slightly oxygenated (DO 2.6 mg L-1), radioactive waters occurs from the toe of the tailings dam into the former evaporation ponds and local drainage system. Seepage waters are calcium-magnesium-sulfate rich with elevated Fe, Mn, Ni, U and Zn values. Oxygenation of tailings seepages causes the precipitation of Fe and coprecipitation and adsorption of other metals (Pb, U, Y), metalloids (As), rare earth elements (Ce, La) and radionuclides (U-235, U-238, Th-227). In contrast, Ba, Ni, Sr, Mn, P, S, Ca, Mg, Na and K as well as Ra nuclides (Ra-226 and Ra-228) remain in solution until pH neutralisation and evaporation lead to their precipitation in efflorescences and sulfate-rich evaporative sediments further downstream. Dry capping of Mary Kathleen uranium mill tailings has resulted in physical containment of the wastes. The dry cover shows no signs of erosion and radiation levels are within acceptable limits. However, the flow rate of surface seepage from the TSF occurs at a much higher rate than predicted. Also, the neutralising potential and adsorption capacity of the tailings and underlying aquifer were overestimated at the time of mine closure. AMD has developed mobilising metals, metalloids, rare earth elements, alkalis, radionuclides and sulfate from the waste repository into surface water seepages.

Jan 1, 2003

The theme i wish to develop in this talk is how we might make use of the scientific and technological knowledge we now have ofextraction metallurgy to meet the present-day needs of the production industry.Before doing so, I would like to say a few words in tribute to Dr. G.K. Williams since he was a past master at precisely what I wish to talk about. I knew G.K., as everybody called him, during the time he spent at Avonmouth in the late 40's and in the 50's. Later, when he was ostensibly retired, I had the pleasure several times of lunching with him when I was visiting Melbourne.When G.K. was at Avonmouth, the Imperial Smelting Process was in that capricious adolescent stage in between the pilot plant and the full-scale commercial unit. G.K. was a great collector of process plant data which hung in cascades from the walls of his office and-from his hand-operated desk calculator. What G.K. understood very well were the basic metallurgical and engineering principles of what was going on in the sinter machine, the shaft furnace and all their ancillaries.

Jan 1, 1985

By S Grant, S Emeric, P Baker, E Jones, D Clark

As we strive for a sustainable and resilient future, repurposing assets has become a top priority. In Australia alone, we have a significant number of mineral projects in the pipeline, extensive existing operations, and over 50 000 legacy sites. Collectively, this presents a unique opportunity to be a world leader in mine rehabilitation. Complex stakeholder landscapes, inflexible policies, aged regulatory frameworks, technical uncertainties and increasing liabilities are all barriers hindering effective transition of legacy assets. The impetus for change is further catalysed by shifting consumer preferences, workforces in flux and regional Australians questioning what the transition means for their local community. We need innovative approaches to take a leading role in the industry and support global efforts more broadly. Co-designing an ambitious, shared vision spanning projects, operations and legacy assets with all key parties is a fundamental step to unlock and realise maximum societal, environmental, economic and reputational value. Serious play and gamification can further enhance this visioning process.

Aug 2, 2023

By Hocking G

For some underground structures, the use of the plane strain assumption in stress analyses may not be justified. The finite element method and photoelasticity have been used to obtain complete 3-D solutions, but, for various reasons, neither method has found universal use. The boundary integral equation method (B.I.E.M.) can be more efficient and economical than the finite element method for 3-D problems involving large volume to surface area ratios. A B.I.E.M. program developed for calculating stresses and deformations in infinite elastic media has been used to determine the 3-D distributions of stress around T- and Y- junctions of circular tunnels in stress fields in which the ratios of horizontal to vertical stress are 0, 0.33, 1.0 and 2.0. For the T- junction considered,stress concentrations at the intersection are approximately twice the plane strain values. Except where horizontal field stresses are high, the stresses in both tunnels approximate the plane strain values at about two tunnel diameters from the point of intersection of the tunnel centre lines. The stresses in the two branches reach those for the corresponding plane strain, two parallel tunnel case two diameters from the point of intersection of thq inner tunnel walls. Very high stress concentra- tions occur in the pillar of rock between the inner tunnel walls near the point of intersection.

Jan 1, 1976

By R Memary

The environmental and economic impacts of a significant dependence on fossil fuels are affecting the future of sectors such as of mining. These impacts are prompting the Australian Government to seek solutions for reducing its dependence on fossil fuels more generally, such developing clean energy and improving energy efficiency. However, limited research has been undertaken to assess the potential synergies between clean energy and mining in an uncertain global future. This paper analyses current energy use by mining in Australia and reviews the drivers and opportunities for energy efficiency and cleaner energy technologies to be coupled to mining under three future scenarios. Linkages between mining and clean energy are investigated for three global scenarios for mining and metals to 2030, developed by the World Economic Forum (WEF), namely Green Trade Alliance, Rebased Globalism and Resource Security. These scenarios are applied to assess how they could change the barriers, opportunities and trade-offs required for the development of a more sustainable energy sources by the minerals industry in Australia.

Nov 22, 2011

The Maddingley brown coal seam at Bacchus Marsh, where mined and bored, tends on the whole to a higher content of volatile matter than the Latrobe Valley brown coals, and this masks the presence of lignitic or earthy coal bands in the bore core analyses. Visits to the Lucifer Open Cut, at Bacchus Marsh, during 1948, revealed, however, a banded condition in the coal seam, as shown in Fig. 1. This banding showed in a face that had been exposed for a considerable period of time, permitting partial drying out and oxidation of the surface coal. The bands consist of different coal types, ,comparable with those found in the Yallournand Latrobe brown coal seams(l).The' light coloured bands in Fig. 1 consist of a buff to light-brown earthy coal of low specific gravity, that closely resembles the pollen coal, that occurs, as similar thin bands in the Yallourn and Latrobe seams. The 40 ft. of coal above the uppermost of these light coloured bands dries out on exposure to a black, closely cracked surface, composed of small dice-like fragments of a lustrous vitrain-like substance, and in every respect resembles the lignitic coal bands of the Yallourn and Latrobe seams.The coal between and below the light-coloured bands develops fewer and more widely spaced shrinkage cracks on drying out, and remains brown in colour and earthy in appearance, resembling the earthy coal of the Yallourn and Latrobe seams.Representative samples were cut of these coals, taking care to exclude surface coal, and analyses were made of them by the Metropolitan Gas Company, through the kindness of Dr. R. S. Andrews, Chief Chemist to the Company...

Jan 1, 1948

Geochemical investigations carried out in the Woodcutters area, Rum Jungle district, NT., consisted of a programme of C-horizon soil geochemical sampling followed by rotary-percussion and diamond drilling.Comparison of detailed geochemical sampling with the original broadly-spaced sampling showed that the structures along which the orebodies occur are reflected very closely by the detailed sampling.A series of vertical rotary-percussion drill holes put down adjacent to a gossan revealed a broad layered dispersion of lead and zinc in the deep lateritic weathering profile, while primary dispersion haloes are only very narrow. The layering appears to be related to the weathering profile.

Jan 1, 1978

Good morning ladies and gentlemen, and may I extend a particularly warm welcome to our shores to those of you who have travelled from overseas to attend this conference. I trust that you will find your visit to New Zealand both rewarding and enjoyable.   This is now my fourth appearance at a New Zealand minerals conference, the second of which has been jointly co-hosted by AusIMM and Crown Minerals. Since taking on the role of Associate Minister of Energy, I have had the opportunity to meet most of the industry players, and to visit a good number of the major mining operations. Through all of this I have become increasingly aware of not only how dynamic the minerals and coal industry is but also the array of factors that affect investment decisions in this business. Many of these factors, such as commodity prices and availability of investment funds, are determined primarily on the international stage. Others however, such as the allocation, regulatory and the fiscal regimes for minerals, are closer to home and are directly influenced by government policy decisions. I will talk more on what the government proposes in this area shortly.   But first, I would like to commend you all on your industryÆs continuing contribution to New Zealand Æs economy. 2004 has seen New Zealand Æs mineral and coal output top $1 billion for the second consecutive year. To put this achievement in perspective, it represents a staggering 47 per cent increase over the national output value recorded just five years ago. Notable contributions over the year came from gold which increased production to 10.2 tonnes (up nine per cent), ironsand production at 2.3 Mt (a 20 per cent increase), and industrial rocks and building stones (up six per cent) with rock for building, cement and roading showing significant rises on the back of strong regional growth and infrastructure development. Many regions, in particular Auckland, Bay of Plenty, Wellington and Southland, recorded significant increased regional activity with supply often struggling to meet demand. By contrast the coal sector had a relatively steady year with production remaining stable at just over five million tonnes for the second year running. Coal exports however are now consistently exceeding two million tonnes annually, generating export earnings of over $200 million, and could well be higher with rail capacity improvements. Many countries throughout the world are now importing our high quality bituminous coal for steel manufacturing and other industrial uses.

Jan 1, 2005

In October 2005 Phelps Dodge mining, a US based company, visited several Australian mining companies and mine sites to ascertain the current applications of risk management methods in the organisation. The results of this review, documented by the author, indicated a ælayeredÆ approach from high level site or major hazard analysis through to face level, æstop and lookÆ, methods. The approaches of several companies were summarised in one simple layered model. This model is helpful to other sites and companies to identify potential improvements but also offers an image of best practice that may assist with the governance of OH&S by both company boards and community regulators. The issue is particularly relevant as we discuss national consistency in mining regulation. This paper examines the layered model, the company and site approaches that helped define the model, as well as the suggested implications of the layered model to governance.

Jan 1, 2006

The paper re-visits an old and proven concept of winzing, a method widely used in the past to gather exploration data for accurate definition of the orebody. It is proposed to use a mobile Supersucker (a giant vacuum cleaner also known as vacuum lift), to carry out winzing activities underground. A brief description of conventional underground winzing used in the past is provided, together with a discussion on other underground bulk exploration methods used in Australia to date. Historical background, principles of the proposed system, Supersucker construction details and productivities, and benefits and advantages of the proposed system in comparison with other exploration methods, are outlined. Other relevant applications of the mobile Supersucker, including surface winzing, are also briefly discussed in the paper. With a view of using the mobile Supersucker to recover all broken ore stocks underground, included are also results of floor sampling conducted recently in the in-stope decline excavated in a coarse gold type, high-grade orebody.

Jan 1, 2002

By Carlini G, Ibba R

The KSS Lead Plant (Kivcet - SNAMPROGETTI - SAMIM) of Por tovesme, owned by Nuova Samim (the sector-head Company for non ferrous metals and derivatives owned by ENI), has been operating since february 1987. This plant is based on the Soviet Kivcet licence and testwork carried out on the pilot plant of VNIITSVETMET in Ust Kameno gorsk fed by the Nuova Samim's concentrates. The plant is com pletely automatized using the most advanced technologies and it is operated by nineteen people on shift work, including all ancillary units and lead decopperizing-casting. The expected performance of the plant has been confirmed and improves day by day in relation of the operating experience, thanks to the new conceptual design of the furnace. Due to the remarkable flexi bility of the process, the integration of the lead plant with the other plants of the metallurgical complex of Portovesme rro-#4 (Electrolytic Zinc Plant, Sulphuric Acid Plant, Imperial Smel ting) has shown all the economic advantages. The lead content in the ambient air, detected by the monitors, either in the working area and on the ground outside the complex, is widely Pb W" below the stricter new limits recommanded by the E.E.C. (Economic European Community) rules and by the Italian law. The whole process is carried out in equipment completely closed and under suction and it does not require manual operations with exposure to the lead. The production cost is much lower than that performed by the traditional technology. This advantage permits wide margin to consider investment to replace the traditional technology.

Jan 1, 1989

A combination of the needs of business, employee desires and safety and health considerations is stimulating increasing attention to the time spent by people at work and the timing of that work. Particularly we are seeing: - innovative work schedules for 24-hour mining businesses; and - response from industry to accommodate the needs, even the desires, of employees in return for systems which are more productive and more capital efficient. There appears to be an evolutionary trend for business management to become more sophisticated and responsive to the need for achieving close to best cost work schedules to sustain continuous improvement. The underlying motivating forces driving this trend for improved techniques in organising attendance at, and time spent at work, is the seemingly inseparable combination of technological advance and ever-increasing accumulation of capital. The mining industry has not remained untouched by this thrust for ever-increasing need for best use of labour, to adopt advances in technology and to provide attractive opportunities for putting accumulated capital to work. An essential component of this on-going thrust is a substantial effort by the mining industry to improve the performance of labour by providing most-productive work schedules.

Jan 1, 1996

By Tamura S, Maekawa M, Nagai C, Deguchi M

Heavy fuel oil has been injected into blast furnaces in order to reduce the coke rate, to improve productivity and to control the furnace heat condition. However, in the first oil crisis at the end of 1973, it became necessary to develop an injection technique of new fuels into blast furnaces to reduce oil consumption. In Kobe Steel, Ltd., it was thought that the injection of a coal-oil mixture (COM) into blast furnaces could be developed in a shorter time than pulverised coal injection. The development of this technique was under- taken in 1974, and COM was injected through two tuyeres of the No.3 blast furnace at the Kobe works in 1977 and 1978. In addition, in order to study the combust- ibility of COM and the phenomena in the tuyere zone, the development of a gas sampling method was under- taken in 1975. In this paper, the results of the injection tests and gas sampling tests are reported.

Jan 1, 1981

By Trutwin W, Tracz J

The outbreak of open fires underground cause disturbances to the conditions of the mine ventilation process. Thermal and chemical effects due to fire create unsteady, transient states in airflow and the spread of combustion products in the mine ventilation network. Changes in airflow have an influence on the fire, constituting a sort of feed-back between the fire and the ventilation process. This paper deals with a numerical simulation method, which enables the determination of transients caused by fires. The mathematical model, of the simulation method considered, has been based upon a: simple model of combustion of fuel in the airway, unsteady exchange of heat between the fire, airflow and surrounding rocks, airflow in mine ventilation networks and the theory of heatflow in the rocks. Initial and boundary conditions allow the determination of a set of parameters describing the airflow, the propagation of combustion products, the tempera- ture of the fire and flow etc. due to the fire. The simulation method, facilitates a graphical presentation of the spread of combustion products throughout the network. The simulation method has been prepared for an IBM PC/AT Computer.

Jan 1, 1988

By Streichfuss M, KeBler H-W, Burgwinkel P

This paper describes the design of an expert system used as a part of a diagnostic system for diesel hydraulic drives. A PC-based diagnostic system ruDi (KeBler and Burgwinkel, 1993) was developed to minimise the time for diagnosis and repair work of vehicles with diesel hydraulic drives used in the mining industry. One part of ruDi is an expert system that helps to locate errors in any of a vehicle's subsystems, and supports technicians in removing the cause of a malfunction. Apart from the standard knowledge of diesel engines and hydraulic transmissions, the expert system supports the interpretation of the data obtained during sophisticated engine analysis tests such as high-resolution speed analysis or high-pressure analysis of the diesel injection system. The expert system is designed to diagnose various vehicles of the same type. Data for each vehicle is stored separately allowing checks to be carried out individually for each machine. An additional feature of this system is a database interface to a Maintenance Planning and Control System (MPCS) that allows an automatic generation of work orders for the defects found during the expert system sessions.

Jan 1, 1995

By Duke J. H

Advanced computer aided geological modelling techniques are now available to the geologist to allow the rapid evaluation of a gold orebody at various stages of its development. The types of grade estimation techniques used change during the various stages as the density of drilling and knowledge of the deposit increases. At the prospect evaluation stage drillhole intercept selection techniques are coupled with preliminary 2D (vein or layer) modelling or 3D block modelling techniques to arrive at a geological resource estimate. At the prefeasibility and feasibility stages more sophisticated 2D and 3D modelling techniques, such as domain controlled grade interpolation with anisotropy, are used along with interactive open pit and underground mine design, to calculate recoverable reserves. At the production stage closely spaced blasthole sample data is modelled quickly and coupled with interactive grade control facilities. Shot volumes, tonnages and grade estimates can be databased to provide reconciliation figures. These modelling techniques are embodied in MINEX-3D, an Australian software system which, with the emergence of the 386-based PC and high resolution (VGA or better) graphics, makes a whole range of advanced geological modelling techniques available to most exploration and mine geologists.

Jan 1, 1989

By Sturgul J. R

ZC Mines investigated a proposal to replace the present underground train haulage system with rear dump trucks. The number of rear dump trucks required to achieve target output and the required mix of trains and trucks during the changeover was of importance to the designers, and a GPSS computer simulation model of the operation was constructed using GPSS/PC, a recent form of the language for the personal computer. Three models were 'constructed to simulate initial and final configurations of underground haulage systems to transport ore from ore passes to the crusher and then to the skip for transport to the surface. The initial model simulated train operation on two levels and rear dump truck operation on a third level. The second model simulated rear dump truck operation on two levels with ore being loaded through the crusher to the skip as in the previous case. The third model replaced the rear dump trucks on the lower level with a train to establish the relative merits of the two methods of transport. The simulations identified equipment numbers, required operating hours and critical points in the operation which can then be addressed by the mine designers.

Jan 1, 1988

In 1984/85 financial year Australia produced 529 thousand barrels per day (kbd) of crude oil. By far the major contribution (453 kbd) was light waxy oil from offshore Gippsland, Victoria. When these discoveries were made in the latter 1960s, imported oil was available in abundant supply and at low prices. Because of this, the Gippsland producers persuaded Government to control the marketing and pricing of their crude, and thus provide the required security of offtake. Political events in the middle East created supply shortages during the 1970s, and dragged up government selling prices for OPEC crude oil. Thus Arab Light crude that sold for less than US$2/barrel (bl) in 1970 reached $34/bl in 1981. Following the consequent decline in world oil demand, in 1982, Australian refiners sought to evade their obligation to lift Gippsland crude. Hence, in 1983, the Government was forced to introduce a floor quota of 385 kbd of Gippsland crude liftings and to allow producers to export any additional production refiners did not require. On expiry of the old arrangements, Government introduced a partial free market from January 1985, whereby the balance in excess of 350 kbd may be sold to Australian refiners at negotiated prices, or exported as before. In 1984/85 exports were some 90 kbd and will be higher in the current year. About half this total has been exported by BHP, providing valuable experience and lessons which are described in the paper.

Jan 1, 1986

By D A. Williams, J C. J Boshoff

The properties of tailings that emanate from laterite nickel processing plants are significantly different to most other mine tailings. They typically comprise a mixture of fine materials that are made up of altered clays, chemical residues and salts. Neutralisation processes that are undertaken prior to tailings discharge result in a high proportion of gypsum in the tailings. The salinity of the pore fluid is commonly higher than 140 g/L of salts, dominated by magnesium sulfate. Hydraulically-placed tailings that undergo solar evaporation typically reach dry densities of less than 1 t/m3 of insoluble solids. In situ water contents after many months of drying may be as high as 80 per cent, and peak undrained shear strengths are unlikely to be greater than 20 kPa.This type of material is not conducive to upstream raising, from both a practicality and overall slope stability perspective. Even at rates of rise of less than 1 m/a, it is difficult to effect upstream raising on unaltered laterite nickel tailings. However, the authors have successfully designed and implemented upstream-raised laterite nickel tailings storage facilities. The upstream raises have been formed from both imported natural materials and air-dried and compacted tailings borrowed from the tailings beaches.Drying and associated strength gain has been achieved through various means of mechanical intervention, repeatedly exposing a zone of tailings to the atmosphere for evaporation. Field trials have been undertaken to optimise the approach, and the findings from the trials have been implemented in practice to allow stable upstream raises to be constructed. The cost savings and reduced environmental impact compared to high-volume downstream raises have been significant.CITATION:Williams, D A and Boshoff, J C J, 2015. Upstream raising of laterite nickel tailings storage facilities, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 271–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By L Jackson, A Parbhakar-Fox, N Fox

"Characterisation of sulfide minerals (eg pyrite, sphalerite) in historic tailings can assist in determining whether there are economic benefits of reprocessing such materials using modern metallurgical practices. In addition, there are associated environmental advantages if the historic tailings are actively generating acid and metalliferous drainage (AMD). At the Old Tailings Dam (OTD), Savage River, Western Tasmania, 38 Mt of pyritic tailings were deposited from 1967 to 1982; consequently it has been recognised as an AMD source. Long-term management options considered for this site have included the establishment of either a water, hard-engineered or vegetation cover. However, due to geotechnical challenges posed and the lack of success demonstrated by previous pilot studies, these strategies have not been implemented. Instead, resolving the pyrite chemistry can allow for a first-pass assessment of whether reprocessing these tailings is a feasible option as part of a long-term management strategy for this legacy site.Tailings samples (n = 144) were collected across the OTD from up to 2 m depth from five facies (A–E), and four zones (1 to 4; defined by hydrological regime and grain size). These materials were subjected to acid-base accounting (ABA) and mineralogical evaluations to determine their geoenvironmental characteristics. Following this, 26 samples were selected for in-depth laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) investigations to evaluate pyrite chemistry across different tailings facies. The results revealed enrichment of Co and Ni in these materials. Specifically, Co content was up to 3.0 wt per cent, particularly within facies C to E, and Zones 3 and 4. Cobalt is recognised as a critical metal, therefore, reprocessing should be considered as a future rehabilitation option for the OTD, pending resource definition using established codes and practices.CITATION:Parbhakar-Fox, A, Fox, N and Jackson, L, 2016. Geometallurgical Evaluations of Mine Waste – an Example from the Old Tailings Dam, Savage River, Tasmania, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 193–204 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016