Search Documents

By E. J. Gleim

The importance of "good voltage," especially for direct-current systems in coal mines, is not always fully appreciated. From the practical aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By W. L. Brien, O&apos

Molybdenum alloys with good strength properties at elevated temperatures were produced by the powder metallurgical internal oxidation method previously applied to tungsten and known as oxyreaction strengthening. Commercial molybdenum powders were blended with 0 to 10 pet of a reactive powder, ZrMo2. The effects of composition, blending procedure, and sintering conditions on strength properties at elevated temperatures were studied. Strengthening was attributed to zirconium in solid solution with molybdenum and to the presence of submicrometer particles of Zr02. Several alloys had tensile strength and stress-rupture properties com-parable with those of the best commercial alloys. The maximum tensile strengths obtained were 92 kpsi at 1,200° C and 53 kpsi at 1,316° C. The maximum stress-rupture life at 30 kpsi and 1,200° C was 145 hours.

Jan 1, 1974

By Natesa I. Jayaraman

A field study was conducted by the Bureau of Mines to determine the feasibility and effectiveness of a secondary ventilation system retrofitted onto an Eickhoff EDW 340L double-drum shearer as a technique for controlling respirable dust generated during a longwall mining operation. An airflow duct was formed by enclosing the bottom of the undercarriage with steel plate and cutting air channels through the ends of the undercarriage frame. Air intakes were provided behind each cutting drum and at several locations along the undercarriage. Grills were installed at the intakes to prevent the broken coal from entering the ducting. A dust collector consisting of 5,000-ft3/min fan, water sprays, and a minicyclone panel was installed on the shearer at the tailgate end. Field results indicated that the secondary ventilation system reduced respirable dust more than 60% along the face. Reduction was less near the intake airway and when secondary dust sources occurred.

Jan 1, 1977

By Frank G. Horino

Drill cores from 18 exploratory holes that were drilled into the unleached saline beds were tested for mechanical properties by the Bureau of Mines. Test cores were primarily selected from zones L4B, R4B, L3, and R3A in the Piceance Creek Basin, Rio Blanco County, Colo. Regression analysis techniques were tried in an attempt to relate kerogen yield or apparent specific gravity to the parameters compressive strength, Young's modulus, and Poisson's ratio. Correlation coefficients were very poor, indicating that this type of analysis was not amenable to these data. Analysis of variance techniques were tried using a division of either greater than or less than 10% nahcolite together with the requirement of less than 3% dawsonite. Results showed that a larger percentage of nahcolite tended to lower the compressive strength and to increase Young's modulus. A second analysis was made using a division of less than 3% dawsonite and greater than 3% dawsonite together with the requirement of less than 1% nahcolite. For this analysis, a larger per-centage of dawsonite tended to increase compressive strength, Young's modulus, and Poisson's ratio. Mean compressive strength values were determined for the mining horizons of interest. Average physical properties for design purposes were also determined for the horizons of interest and for a proposed adit based only on logged geologic depths to these horizons. No consideration was given to percentages of nahcolite and dawsonite. Creep data obtained from nahcolite-and dawsonite-rich oil shales provides a best fit to a modified power equation.

Jan 1, 1978

By D. Christofferson

This final report documents the cooperative efforts of the Engineered Systems Division and the Mining Equipment Division of FMC Corporation during performance of Bureau of Mines Contract H0252091. Improved operator compartments incorporating overhead canopies, logical arrangements of controls, and design features offering greater operator comfort were developed and retrofitted to the FMC 320A roof bolter and 6L shuttle care The vehicles were evaluated in underground operations at separate mine sites. The successful evaluation has resulted in incorporation of the designs as standard features of the 320A roof bolter, and the 5L, 6L, and 10L shuttle cars.

Jan 1, 1978

By F. W. Wood

The use of consumable.-electrode arc melting as a production technology is growing. One advantageous feature of this process is that it avoids ingot contamination by soluble crucible materials by employing a chilled metal crucible. Because the thermal balance under these conditions is rather delicate and does not necessarily provide a favorable environment for solidification, catastrophic imbalances can occur. The effectiveness and mechanistic roles of various factors are mostly unknown, and more intelligent insight regarding the distribution of temperature and heat is needed. Experience has provided several pertinent observations, some of which are quite superficial. The most meaningful data have resulted from studies of molten pool shapes and sizes and from measurements of heat flow through crucible walls. Overall experience, intuitively interpreted and supplemented, is sufficient nevertheless as a basis for a boundary-value treatment of the problem. A mathematical analysis based on a separation of variables, using conventional differential equation methods, provides a useful solution. For a cylindrical ingot, the temperature varies as a Bessel function of an argument proportional to the radius and as an exponential function of longitudinal position. Trial calculations using the problem solution seem to verify the general correctness of the result as compared with experience. The role and nature of solution parameters are also clarified, though not entirely resolved. It is revealed that the barrier to heat flow at the ingot-crucible surface has a prominent influence. Utility of the model embodied in the problem solution is readily demonstrated by considering a variety of contemporary questions about arc melting, and it is hoped that utility can be enhanced by improvement of the model.

Jan 1, 1968

By John K. Alley

Despite the extensive use of fluorphlogopite, investigators do not agree as to its exact melting temperature. Data on other fluormicas and on related fluorsilicate systems are largely nonexistent. A knowledge of the melting temperature is necessary for the effective synthesis and use of fluorphlogo¬pite or other fluormicas. The increasing use of two- and three-mica systems to yield polycrystalline ceramics has made more urgent the need for melting temperature information concerning these other fluormicas. This report is part of a program by the Bureau of Mines to synthesize large-size or large-crystal fluorphlogopite and develop a usable reconstituted fluormica sheet. The melting temperature of fluorphlogopite, K2Mg6A12Si6020F4, was found to be 1,383° ±2° C. This temperature was found by studying single crystals of fluorphlogopite, heating behavior of glass of fluorphlogopite composition, and the actual crystallization of fluorphlogopite from a melt that had been heated above 1,430° C. The formation of forsterite or norbergite was directly proportional to the loss of volatiles during the experimentation. Many trials revealed that the only reliable seal was a thick platinum sheet with welded seams. If no volatiles were lost, neither norbergite nor forsterite were formed; fluormica was then the only product. Excellently formed crystals of forsterite with an optical sign different from ordinary forsterite were obtained during the single crystal melting experiments. These crystals resulted from a slow loss of volatiles. A congruent melting of fluorphlogopite is indicated by the data of this report; however, incongruency within a small temperature range is not precluded. A more refined method using phase equilibria-quench methods would be necessary to settle the question absolutely.

Jan 1, 1962

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rim. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By D. Harrington

The experience of the past 2 years has demonstrated clearly that mine explosions with heavy loss of life can be prevented. The investigations of the Safety Division of the United States Bureau of Mines disclose that during the fiscal year 1934 there were only 28 deaths from mine explosions in the United States, and during the fiscal year 1935 there were 54 deaths, a very favorable reduction when compared with an average death toll of 265 from this cause during the 20-year period prior to 1929. Although the frequency of occurrence of explosions has not decreased greatly during the past 7 years, there has been a marked decrease in severity, indicating that the coal-mining industry is taking more effective precautions to prevent the spread of explosions. A number of large coal-producing States, which in past years have experienced numerous disastrous explosions, have been free from such disasters for continuous periods of as much as 5 years or even longer. A study of several hundred mine explosions occurring in the United States during the past 10 years or more indicates that the factors mainly responsible for these explosions are inadequate or defective ventilation and disregard of the hazards from explosive gas. Both of these factors are subject to control, and if controlled it is safe to say that deaths from explosions would be reduced to a negligible number as relatively few explosions are now initiated by dust.

Jan 1, 1936

By Roy T. Sorensen

As part of its mission to maintain an adequate supply of minerals to meet national needs and maximize mineral production from domestic sources, the Bureau of Mines is investigating the recovery of alumina by hydrochloric acid leaching of kaolinitic clay. Most iron impurities are leached from the clay along with the alumina and must be removed before or during crystallization to aluminum chloride hexahydrate. The thermal decomposition step then provides an alumina product of acceptable iron analysis. Miniplant studies of a Bureau-developed solvent extraction technique, using a tertiary amine in kerosene diluent, have demonstrated that the iron content in aluminum chloride leach liquors can be reduced to levels of less than 0.007 wt-pct (7 ppm), expressed as Fe203. Entrained and dissolved organic matter in the purified pregnant leach liquor from the solvent extraction circuit can be reduced to less than 2 ppm by using a fabric-packed coalescer and subsequent activated carbon treatment. Investigators discovered that a steady buildup of zinc accumulated in the solvent phase within the extraction circuit, proportional to the amount of leach liquor treated. The solvent phase zinc analysis increased by 0.01 wt-pct ZnO for each 1,000 gal of pregnant leach liquor purified.

Jan 1, 1981

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state requlatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980

PRODUCTION of cesium, cesium salts, and rubidium salts in the United States declined somewhat from 1961 levels; rubidium production was virtually unchanged. Imports of pollucite declined because consumption was supplied partially out of inventory. Domestic Production.-About 50 tons of pollucite was reported mined at the Tin Mountain mine in the Black Hills of South Dakota. The Dow Chemical Co., Midland, Mich., MSA Research Corp., Callery, Pa., and Penn Rare Metals, Inc., Revere, Pa., produced a total of 159 pounds of cesium. Rubidium production remained essentially the same as in 1961. Shipments of the two metals by these companies and by American Potash & Chemical Corp., Trona, Calif., totaled 279 pounds. Production of cesium and rubidium salts by American Potash & Chemical Corp., Penn Rare Metals, Inc., and Rocky Mountain Research, Inc., Denver, Colo., declined substantially during 1962.

Jan 1, 1963

By H. B. Humphrey

[EXPLOSION of gas and dust in coal mines, have caused death t lid injure to mines, and destruction of workings in all countries where coal is mined underground. In the United Stales the first reported explosion wits in Min; explosions have continued to the present. The danger to film ill it mine When an explosion occurs in not always measured by the violence created or by their nevi lies, to the area through which flame and Violence extend. As many, perhaps more, risen have died from gases and lade of oxygen (known as "after-damp") than have been killed by the blast and hart. Me explosions often are caused by it combination of factors, including concentration of methane in air, formation of clouds of dust, and the presence of a flame or spark. These explosion factors have varied with changes ill milting method and practises over the years, but the basis causes have always been the salve. Understanding of the causes and to acceptance of ways to guard against explosions and their effects have been slow to spread from investigates to officials and Own to bosses and miners. To a considerable extent there hats lawn a belief that explosions were a joining risk but might hr, put oil hut could not be presented. Such belief is based on the human failure to maintain and observe necessary precautions. These failures, caused by inertia to change, carelessness, or reliance on continuance, of past explosion-free years, are being reduced in number and effect by education of miners and supervisors and acceptance of higher prevention standards.]

Jan 1, 1959

By F. A. Penning

An experimental and analytical investigation was conducted on a recoverable pit bottom buffer. Work was conducted at the Colorado School of Mines using the U.S. Bureau of Mine-s free fall test tower. The four-sided butter, one of several designs by Cable Belt Ltd., was constructed of reinforced rubber slabs. The kinetic energy of falling weights, 1670 to 6000 lb, was absorbed by the flexure of rubber slabs loaded along their edge. A series of constant energy, 3000 ft-lb and maximum design velocity, 600 fpm tests were conducted. Static testing of the buffer established the load-deformation behavior. A large hysteresis loop plotted above and below the data published by the manufacturer. Creep was evident during; the loading Lend unloading cycle. Electronic instrumentation measured deceleration using your accelerometers; overall and intermediate movement was found from four displacement transducers; bending strains were recorded at four locations; and base reactions were measured by using four load cells. Data were recorded on tape and played back on a recording oscillograph. High speed movies were taken of all the tests. Symmetry of response and rebounds, when they occurred, were noted. From the displacement-time and load-time data, maximum decelerations were calculated by four methods and different assumptions. Good agreement was found from these approaches. Impact loads ranged from a low of 0.7 to a high of 6.1 gs. A dynamic computer model was written for the response of the buffer. Displacement-time, and acceleration-time plots show close correspondence with experimental data for the ten experiments. Data from accelerometers, displacement transducers, strain gages, and load cells are included. The computer program listing, and displacement-time acceleration-time plots are also presented.

Jan 1, 1980

By Roger E. Burleigh

In June, 1989, the U.S. Bureau of Mines, undertook a 9-day evaluation of the tin resource potential of the Sleitat Mountain tin deposit. Significant tin-tungsten mineralization is associated with quartz-topaz-white mica-tourmaline greisen alteration of a multi-unit, 57 Ma, peraluminous, granite stock which intrudes Cretaceous Kuskokwim Group flysch deposits. The granite comprises marginal biotite-, intermediate biotite-muscovite-, and central zinnwaldite-granite units, interpreted as a zoned alteration system. Major vein mineralization is confined to two east-west-trending zones of steeply oriented tabular lenses of greisen interleaved with mildly altered granite. Cassiterite is the dominant ore mineral while arsenopyrite, loellingite, wolframite, pyrite, sphalerite, chalcopyrite, and bismuth-oxides are present in minor to trace amounts. The north and south greisen zones are estimated to contain an inferred resource of 128 to 212 million lbs Sn in 28.6 million st of mineralized rock. An 1,800-lb representative bulk sample contained 0.37% Sn, 0.04% W and 17 ppm Ag and is considered an average grade estimate for the deposit. Drill testing by Cominco Alaska Exploration indicates that substantial widths of high-grade tin mineralization are included within the lower grade disseminated mineralization. Depth of deposit erosion is substantial and there exists a high probability for placer tin deposits.

Jan 1, 1991

By F. D. DeVaney

Metallurgists and coal-washing engineers have used heavy liquids for years in studying the characteristics of ores and coal. By such means true separations can be made between the various specific-gravity increments in the materials examined. To use of heavy liquids has permitted determination of the possible grades of tailings and concentrates by specific-gravity methods on any particular size, and therefore the size to which the ore must be crushed to free the valuable material. The simplicity of float-and-sink separation and the high degree of efficiency attained in the laboratory are factors that commend the method for commercial concentrations.

Jan 1, 1940

By F. D. DeVaney

Metallurgists and coal-washing engineers have used heavy liquids for years in studying the characteristics of ores and coal. By such means true separations can be made between the various specific-gravity increments in the materials examined. To use of heavy liquids has permitted determination of the possible grades of tailings and concentrates by specific-gravity methods on any particular size, and therefore the size to which the ore must be crushed to free the valuable material. The simplicity of float-and-sink separation and the high degree of efficiency attained in the laboratory are factors that commend the method for commercial concentrations.

Jan 1, 1940

By Mark S. Sanders

This report presents a summary of the work reported by Sanders and Kelley (1981). A task analytic approach was used to define information requirements and visual features which served as sources of information. Information requirements were prioritized and the location of visual features determined. From this analysis, visual attention locations, containing one or more important visual features, were indentified. The visual attention locations are contained in this report. A procedure was developed for assessing whether operators in existing machines could be expected to see the visual attention locations. The procedure makes use of a Human Eye Reference Measurement Instrument (HERMI) designed for this project and an outside-in photographic procedure for documenting compliance with the recommendations. A sample of continuous miners, shuttle cars & scoops were used to test the procedure. Illustrative results are presented in the report.

Jan 1, 1981

By Mark P. Zaitsoff

The project involved design, construction, and testing of hydraulic models of culverts, decant and open channel spillways which are typical drainage structures used for protecting mine waste embankments. MSHA (The Mine Safety and Health Administration, U. S. Department of Labor) made a motion picture of the tests. Tests results and products in the forms of graphs, tables and films, demonstrate the principles and factors which govern the function and performance of the three types of drainage structures.

Jan 1, 1981

By Robert Stefanko

A series of workshops were conducted -with invited participants from the coal mining industry to identify the most pressing research and development needs of the industry. Six workshops were held on the following subjects; Research Priorities for Mining-Oriented Universities, R&D Needs-for Surface Coal Mining, R&D Needs for Deep Coal Mining, R&D Needs for Anthracite Coal Mining, R&D Needs for Coal Mine Health and Safety, and R&D Needs far Environmental Control in Coal Mining.

Jan 1, 1975