Search Documents

By A. Zeni, S. L. Bessinger, T. A. Palm

San Juan Coal Company (SJCC) operates an underground coal mine near Farmington, New Mexico. Continuous miners and a longwall produce 7-8 million tons per year. The coal seam at SJCC has tested to have a propensity for spontaneous combustion. As such, during feasibility for this project, it was elected to utilize a bleederless ventilation system on the longwall. Three-entry gateroads are developed, and the longwall gob is sealed as mining progresses. SJCC utilizes a nitrogen injection system to continuously inertize the gob. In 2004, the mine was nearing completion of its first longwall district. The next district would contain longer panels (up to 12,500 feet). Due to the liberation of methane, and to a lesser extent hydrogen sulfide, a typical wrap-around ventilation system would not be appropriate. Not only would gas concentrations likely be challenging, but the overall ventilating pressure in the mine would have to be increased beyond limits established to mitigate the potential for spontaneous combustion. Given the above-described operating constraints, SJCC determined a need for a small ventilation shaft in the back (longwall setup area) of the next district that would draw adequate air past the longwall seals to maintain low gas levels and permit the required regulatory inspections to occur. Extensive ventilation modeling and gas desorption testing indicated that the shaft would be required to handle a volume of air ranging from 40,000 cfm to as high as 185,000 cfm. This large range is driven by the position of the longwall face with respect to the shaft and the effectiveness of the SJCC degasification program (SJCC uses vertical gob vent boreholes and horizontal in-seam methods). Ventilation simulations determined an appropriate diameter for the 350-ft-deep shaft to be 5 feet. Having determined shaft size, the next decision related to the method of shaft construction. Conventional shaft sinking was ruled out, due to the small diameter. Raise boring was an attractive option but had two drawbacks: (1) development crews would reach the bottom of the shaft just a few weeks before longwall startup, leaving a compressed timeframe to install the shaft, and (2) raiseboring requires additional underground entries to be developed to stow the project’s cuttings. While raiseboring remained a viable option, the problems associated with it led SJCC to also investigate blind drilling.

Jan 1, 2006

By S. Dixon

The Phelps Dodge - PD/PERI Heap2D Model is a phenomenological stockpile leaching model that has been used to investigate the best operating practices for leaching chalcocite. The model was used to investigate the interrelationships of raffinate application rate, aeration rate, raffinate iron grade, acid cures, lift height, crush size, bulk density, air injection spacing and raffinate drip emitter spacing.

Jan 1, 2006

By J. J. Sammarco

Illumination is essential for mine safety because miners depend most heavily on visual cues to detect hazards associated with slips/trips/falls and powered haulage. The National Institute for Occupational Safety and Health (NIOSH) is conducting mine illumination research to improve miner safety by enhancing a miner?s ability to see mine hazards. Thus far, 16 papers have been published covering diverse topics such as cap lamps, machine-mounted lighting, glare, lighting maintenance, and light-emitting diode (LED) technology issues. NIOSH has also developed an LED cap lamp, LED area lighting, and a Visual Warning System (VWS). This paper provides an overview of the improvements from NIOSH-developed lighting that include: 94% faster trip hazard detection with the NIOSH LED cap lamp; 79% faster peripheral motion detection to detect pinning/striking hazards; no increase in glare; 71% faster machine movement hazard detection with the VWS. Current research is described concerning an LED cap lamp for metal/nonmetal miners, illumination for refuge alternative deployment and inspection, and whether lighting could be used to improve miner escape and rescue in smoke. Lastly, future possibilities of using lighting to improve miner safety are described.

Feb 27, 2013

By O?Connor. D. F.

The ever increasing energy costs associated with mining at depth has become an important issue that needs to be addressed for future sustainable production. Vale Inco Limited?s Creighton Mine being the deepest has the highest energy cost per ton due to the ventilation system requirements. A review of the ventilation systems was undertaken with respect to current practices and identification of opportunities to the practical application of technology that would facilitate energy savings. Energy conservation initiatives such as time of day controls have been implemented; however there still remained some opportunity for further reduction. Based on previous studies that identified opportunities due to actual time spent in the workplace, our mining method and ventilation design, it was determined that Ventilation on Demand (VOD) could provide further additional energy reductions with respect to our auxiliary fans. A pilot project has recently been initiated to apply a Ventilation on Demand concept to two 112 kW auxiliary fans and their related workings located on the 2340m level of Creighton Mine. The project objective is to determine the practical methodology and application of this technology in the field. This project involves the installation of variable frequency drive (VFD) starters on the auxiliary fans to allow variable volume (through speed control) based on demand. The required flow is determined based on equipment and/or personnel via identification tags. The Fans adjust to the flow requirements as measured by flow sensors. Since the fans are sized for the final requirements the required flows can be achieved regardless of system length. Energy savings are realized by supplying only the volumes (power) as required and only when required. This paper discusses the rational and program being tested at the VALE Inco Limited, Creighton Mine.

Jan 1, 2009

By Charles Ronkos, Jeffrey Edwards, Brian Brodsky

The Marlin gold-silver deposit is in western Guatemala, 15 kilometers south of a major transform fault that separates the North American and Caribbean plates. A district-scale, northwest-trending graben controlled deposition of a greater than 1200 meter thick upper Tertiary quartz latite to rhyolite volcaniclastic sequence. These volcanics were subsequently intruded and unconformably overlain by a small intermediate, latite to andesite, volcanic complex. Classic low-sulfidation, quartz-calcite-adularia veins and stockwork formed a 2.2 million ounce gold deposit, in association with late-stage andesite dike swarms, along a west-northwest striking normal fault on the eastern flank of the volcanic complex.

Jan 1, 2005

By F. Bruey

The Factorial Model Experimenters are often interested in systems that are multi-factorial. A multi-factorial system is one whose output is believed or known to be dependent on the particular settings of several inputs, or factors. We can think of these factors as defining a space, with each point in this space corresponding to a particular set of factor settings. Experimenting can be thought of as exploring this space - finding out how the response of the system changes as factor settings are changed. There are several challenges in this exploration, among which are deciding what region to explore, designing an experiment that explores it most effectively, and describing the results of the exploration. This paper deals principally with the last of these; it shows how the factorial model can be used to describe how the response of the system changes as factor settings are changed. A strength of the factorial model is that it treats the factors as causes of change in the system's response and focuses on relations among these causes. In particular, the factorial model focuses on whether causes act independently on the system (in a sense to be explained below), or whether they interact. This is important because the experimenter generally seeks to control the system, and because control based on causes that act independently of other causes is relatively simple, whereas control based on causes that interact is more challenging. Also, mapping the space - finding out how the response of the system changes as factor settings are changed - will require less work if, during the exploration, it can be determined which of the causes act independently. For the sake of example, let us assume that the space we are exploring is three-dimensional, and that we have already defined, for each of the three factors, the range of interest. Let us consider all the ways in which the response of the system might depend on the settings of these three factors. In the simplest case, the response in this region does not depend on any of the factors. The response is constant throughout the space, at say, 80 units.

Jan 1, 2007

By M. Zhang, M. Menabde, R. Middleton

Whilst mine planners almost universally assume deterministic forward commodity prices when undertaking valuations of mining projects, historical data well demonstrates that those prices are quite volatile. This paper seeks to understand and quantify how this forward price uncertainty will impact mining project valuation. This paper will also present a way of computing an upper bound on the expected Net Present Value (NPV) of a mining project given forward commodity price uncertainty.

Jan 1, 2007

By Werner Burger

Earth Pressure tunnel boring machines are tackling difficult ground conditions that five years previous were not considered feasible. The technology has evolved that allows EPB TBMs to cross into areas that with the latest in conditioning and special design considerations are now possible to mine. This paper will review the various recent developments and those projects where these new techniques have been applied.

Jan 1, 2008

By A. Cole, F. Porretta

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

Jan 1, 2002

By Jon Hurt

INTRODUCTION The entire scope of new facilities for Lake Mead Intake No. 3 includes a sub-merged intake structure, a deep tunnel beneath Lake Mead, a tunnel access shaft, Intake Pumping Station No. 3, and connections to an existing intake and water treat-ment facility, as shown in Figure 1. In March 2008 Vegas Tunnel Constructors (VTC), a joint venture of Impregilo SpA and SA Healy were awarded a $447m Design-Build contract by SNWA for a section of this work (Contract 070F 01 C1), including the 185 m deep tunnel access shaft, the 4.7 km long, 6.1 m diameter tunnel and the submerged intake. Arup, supported by Brierley Associates, is the Design Engineer for VTC. The scope of the work is shown in Figure 2. This paper will describe the design and construction on this contract, with a focus on the access shaft which is the most complete section of the work. The shaft is being sunk using drill-and-blast methods with the finallining placed as excavation proceeds. The shaft passes through a major fault zone, and extensive pre-excavation grouting for water control is required for much of the depth of the shaft.

By K. Mondal

A macroscopic approach integrated with microscopic analyses for wettability characterization is presented. Wetting depends on 1) Contact between the dust and the fluid droplets, 2) Wettability of the particles by the wetting fluid, and 3) Wettability rate (due to low contact times). The goal of this paper is to show that the wetting rate is a significant factor in dust control. Samples from the roof, three different horizons of the coal seam and the floor were pulverized to less than 25 µm. Experiments were conducted with known wetting fluids to correlate surface tension and equilibrium wettability. Further analyses were performed in terms of surface charge (zeta potential), particle size, mineral composition, elemental composition, and quartz content. The surface tension reduction was also achieved by the use of chemicals and/or altering the temperature of the water. Two methods were used to evaluate wettability rates: a) near real-time comparison of wettability rates, and b) comprehensive evaluation of the intrinsic wettability rates. The data obtained provides meaningful insights towards the design of engineering controls for an economical solution to dust control in coal mines.

Jan 1, 2012

By Kazem Oraee

In underground coal mining, particularly room-and-pillar methods, the coal pillars play a significant role in roof stability. If the pillar dimensions are increased, the pillar bearing capacity also increases, but more coal remains in the pillar and therefore the recovery of mining operation decreases. Therefore, determining the optimum pillar dimension based on technical, economical and performance parameters is important. In this paper, the coal pillar is designed by using the concept of ground reaction curve (GRC). For this purpose, the GRC for coal pillars is drawn and then the elastic and plastic zone of coal pillar behavior is determined. Based on elastic and plastic zone, different equations are presented to draw a pillar reaction curve and the process of coal pillar design based on GRC is explained. As a case study, this new technique is applied to study the coal pillar state in Tabas coal mine of Iran. The results show that the presented new approach is successfully used in the design of the optimum coal pillar dimensions, and also determines the elastic and plastic behavior limit, which is important especially for the logical design of yield pillars.

Jan 1, 2009

By David Van Horsen

Big Creek Tunnel 2, constructed in 1912, is located in the Sierra Nevada Mountains of California, east of Fresno. It is horseshoe and circular shaped with a 3.6m (12ft) diameter and extends 6.6km (4.1mi). Historically, tunnel performance suffers from highly jointed rock and low cover. In 2003, leaks were observed surfacing through outcrops of highly jointed graniodiorite, and subsequently investigated by visual inspection, joint mapping, ground penetrating radar, and a water-tracing survey. Several grouting targets were identified as a result of these investigations. Cement grouting was used to fill void spaces, broken rock and open joints expected to exist behind the concrete and steel liners. Project work consisted of grout hole drilling through the existing concrete liners, and grout placement through squeeze packers supplied by standard grout hose and portable grout plants. Grout pressures were typically 20?30 psi. Grouting was completed in 16 days with a total of 1,550 sacks of Type II/III grout placed at the three likely leak source areas. No grout was observed exiting the tunnel and the leak was stopped.

Jan 1, 2008

By Meisam Ghiasi, Mohammadreza Khalesi, Mahmoud Abdollahy

In the current research, isothermal experiments of kinetic analysis were performed at different temperatures (800–1050 °C) and particle sizes (885 to 10,763 μm) to investigate the calcination kinetics of high-purity limestone. Thermal analyses were carried out in a zirconia crucible, 1 cm in height, for different temperatures and particle sizes. The reaction rate coefficients were varied in the 2.2 × 10−5-1.62 × 10−3-m0.6.s−1 range. Moreover, various isothermal kinetic analysis methods were applied to assess the decomposition mechanism and the calcination function governing the process. The modified shrinking core model was found as the best representation of the high-purity limestone kinetic data. The activation energy was evaluated using the Arrhenius curve, and an average value of 86 kJ.mol−1 was obtained.

Sep 15, 2020

By Shawn Collins

BACKGROUND The history of the Pine Point Mine is a rich one. This property once boasted one of the largest and most profitable lead-zinc mines in Canada's long and storied mining history. The Pine Point mine used open pit technology to extract the ore, but they faced several challenges. In addition to logistics problems with haul distances and metal prices, the mine faced the challenge of a large in flow of water from the Great Slave Lake. Eventually, the Pine Point Mine was closed leaving behind a large deposit of lead-zinc ore. Following the closing of the Pint Point Mine, Tamerlane Ventures Inc. acquired this property which includes approximately 70 million tonnes of lead-zinc reserves. The initial phase of this project will concentrate on the R-190 deposit as a test site to prove their new approach for extracting the ore. The R-190 reserve is believed to have approximately 1,014,000 million tonnes of high grade ore varying from 5% to 52% combined lead-zinc. Once the pilot project proves the approach is valid, the process will be repeated in approximately 33 other ore bodies on the property. This paper is written to discuss the design process to determine the most effective means of placing production and service equipment in the same shaft. Currently the design work and the mining scheme is complete, but lead-zinc pricing has prevented Tamerlane Ventures Inc. from moving forward with the project.

Draglines are one of the largest land-based equipment moving across the earth. They typically ranging in size from2.5 to 6.5 kt (2,750 to 7,100 st). Their size, though, makes them difficult to maintain. Recently, G&S Engineering Services used an Enerpac synchronous hydraulic lifting system to lift a 3.2-t(3,500-st) dragline at the Curragh Mine in Queensland, Australia’s Bowen Basin.

Jan 1, 2004

By C. C. Russelll, V. T. McLemore

The Metals Mining Sector of the Acid Drainage Technology Initiative (ADTI-MMS) addresses technical drainage-quality issues related to metal mining and related metallurgical operations, for future and active mines, as well as, for historical mines and mining districts. One of the first projects of ADTI-MMS is to develop a handbook describing the best sampling, monitoring, predicting, mitigating, and modeling of drainage from metal mines, pit lakes and related metallurgical facilities based upon current scientific and engineering practices. One of the important aspects of planning a new mine in today’s regulatory environment is the philosophy of designing a new or existing mine or expansion of operations for ultimate closure. The holistic philosophy taken in the ADTI-MMS handbook maintains that sampling and monitoring programs should be designed to take into account all aspects of the mine-life cycle. Data required for the closure of the operation are obtained throughout the mine-life cycle, from exploration through post-closure.

Jan 1, 2004

By Liming Yuan, John C. Edwards, Gene F. Friel, Robert A. Franks

Diesel fuel fire experiments were conducted in NIOSH’s Pittsburgh Research Laboratory’s (PRL) Safety Research Coal Mine (SRCM) to determine the critical air velocity for preventing smoke rollback. Such information is necessary for the preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 kW to 300 kW depending upon the fuel tray area. Airflow in the 2 m high and 2.9 m wide coal mine entry was regulated during the course of each experiment; measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor; and recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light obscuration monitors, ionization smoke sensors, and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics (CFD) fire dynamics simulator.

Jan 1, 2005

By H. Gurgenli

Mining companies require accurate short-term mining forecasts to meet budget targets and customer needs. Challenging mining conditions along with employee turnover and lack of standard geologic modeling and mine planning processes can result in time-consuming and inconsistent mine plans. Documentation and automation of the processes involved in mine planning, as well as proper software utilization, are critical in overcoming these challenges. This paper discusses the steps involved in achieving an optimized mine planning system to accomplish productive and cost effective operations. In addition, a case study is included to describe the process of implementing a semi-automated system whereby the geologic model and mine scheduling database are updated monthly to incorporate changes in geology in a relatively complex open-pit coal mine. This case study proves that the ability to update geologic models based on the latest information gathered from production drilling and mining activities can greatly enhance the ability to accurately predict short-term mining production.

Jan 1, 2011

By J. L. Yordan, J. Kortmeyer, I. Yildirim

Talc is used to remove stickies from pulp during paper recycling processes. It is well known that the interaction is controlled by the surface chemistry at the talc/water, sticky/water and talc/sticky interfaces. If the interfacial tensions are known, one can calculate the free energies of interaction and hence predict whether the stickies can be removed by talc. In the present work, the surface tensions of several different talc samples were determined using the acid/base theory. The information was then used to determine appropriate interfacial tensions, which in turn were used to determine the free energy of interaction between talc and stickies. It was found that the calculated free energies are much more negative than those between the stickies and other minerals such as calcium carbonate, bentonite clay and kaolin clays.

Jan 1, 2002