Search Documents

By Robert S. Hendricks

LOCATION AND HISTORY The Lakeshore Copper property is located on the Papago Indian Reservation approximately 30 miles South of Casa Grande, Arizona. This major porphyry type deposit was discovered by El Paso Natural Gas Company in 1966. Following an extensive diamond drilling program, El Paso invited several mining companies, including Hecla, to examine the property with a view towards participation. Hecla's examination, and the attendant feasibility studies, led to agreements, which were finalized in September 1969, whereby Hecla would acquire a 50% interest in the property, and would act as operator. The Lakeshore deposit covers an area approximately 3,000 feet in width by 6,000 feet in length. It consists of an upper zone of disseminated copper oxides, averaging approximately 100' in thickness overlying a zone of disseminated copper sulfides up to 1,000 feet thick. Near the base of the disseminated ore is a blanket like zone of high grade copper sulfides, referred to as the tactite ore body. The mine is being developed to produce approximately 6,500 tons per day of oxide ore and 9,000 tons per day of sulfide ore. This represents a total daily production rate of 15,500 tons per day, which will be achieved by underground mining methods using rubbertired dieselpowered mining equipment. DEVELOPMENT LAYOUT The mine is being developed by two parallel 15° decline tunnels. The declines were collared 5,000 feet southeast of the ore body, and are being driven in a northwestery direction, to pass beneath the tactite ore zone. The declines will constitute the primary means of access to the underground workings. One decline (north

Jan 1, 1997

By P. J. Bethell

Background Increasingly complex geological conditions, with the presence of high ash binders in the mining horizon were encountered at the A.C. I. Dugout Mine near Price, Utah. This led to the production of high ash coal from the Dugout Mine during 2003 and 2004. This material had poor marketability and posed operating issues for the utilities burning the coal. Ash levels increased from typical levels in the 9-12% range to between 15 and 25%. etween 15 and 25%. Reviews of the mine plan and expected geological conditions indicated that further periods of high ash production could be expected. Action Plan Detailed sampling of the mine high ash production was carried out. The majority of the coal from the Dugout Mine is trucked to the Savage Coal Terminal (SCT) at Wellington, Utah where it is stored in multiple piles by quality. Coal at the mine is segregated by a CoalScan 2600, on-line analyzer into high ash, low ash and rock chute (waste material). From these piles, the material is crushed prior to shipment to SCT. The samples obtained from the various high ash piles were subjected to detailed sizing and washability analysis. Once this information was obtained, alternative circuit configurations were evaluated to process this material into a salable product. Water supplies in the arid terrain where the plant is located are scarce. This factor played a part in the final circuit design.

Jan 1, 2008

By James D. Bliss

Sedimentary deposits of pluvial Lake Bonneville are an important source of sand and gravel suitable for aggregate and construction in Utah. Data on Lake Bonneville basin sand and gravel deposit thickness, volume, grain size, percent of fines, and durability were statistically analyzed to detect variations associated with geologic domains, geographic location, Lake Bonneville shorelines, and sand and gravel deposit type, and to construct quantitative deposit models. Analysis showed several trends; (1) sand and gravel in younger shorelines was slightly more durable and the deposits considerably larger in volume, (2) younger shore- lines are also more likely to contain more than one genetic deposit type, (3) the volume of terrace deposits is larger than beach deposits, (4) terraces and beaches are generally thicker than spits and bars, (5) the northern part of the Bonneville Basin contains slightly more durable sand and gravel than the southern part of the basin and is more likely to contain deposits composed of more than one genetic deposit type, aid (6) the Wasatch domain deposits are composed of more than one genetic deposit type more often than deposits of the Basin and Range domain. Three additional conclusions with immediate economic significance are; (1) the median sand and gravel deposit in the Wasatch domain, 360,000 m3 (275,000 yd3), is three times larger than that of the Basin and Range domain (120,000 m3 [90,000 yd3]), (2) the median deposit thickness in the Wasatch domain, 5.8 m (19.0 ft), is nearly twice that of the Basin and Range domain (3 m [lo ft]), and (3) the Wasatch domain also contains slightly larger diameter gravel. These three conclusions are significant because the trend for sand and gravel development in the Bonneville Basin is to move from the Wasatch domain to the Basin and Range domain. Smaller, thinner deposits with smaller diameter gravel will require more surface area to mine than would have been necessary in the Wasatch domain. The result is a higher cost for sand and gravel in construction projects in the Salt Lake City area, especially since the gravel must also be hauled farther.

Jan 1, 2001

By B. Burke, R. Colquhoun, K. Thomas, R. Walton, D. Fentie

The new Roasting Facility at Barrick’s Goldstrike Mine in Nevada, U.S.A. was developed to process 12,000 tons per day of refractory gold ore. The process consists of crushing, dry grinding, roasting, extensive gas purification, calcine quenching and leaching in the presence of activated carbon. The new plant is integrated into the existing Goldstrike facility, treating ore from both open pit and underground sources. The process design, procurement, construction and commissioning of the Roaster facility was performed successfully over a 3½ year period with peaks of 400 engineering personnel and 950 construction personnel supporting the project. The US$330,000,000 project was completed ahead of schedule and under budget. The commissioning was well planned and proceeded smoothly through a rapid start-up to achieve all primary goals within three months of the start of processing of ore.

Jan 1, 2001

By G. R. Robinson

Aggregate resources consist of sand and gravel, and crushed stone. They are large-tonnage, bulk-minable mineral commodities that are used in construction and industrial activities (Tepordei, 1999, 2001).Rates of aggregate production, use and mine permit approval in the mid-Atlantic region differ by population density. These rates are influenced by economic and human factors, such as demand, costs, land availability and community opposition. In some areas, the local availability of aggregate is limited. This is due to the lack of suitable local source materials for aggregate, the loss of potential high-quality aggregate resource production sites by preemptive land development and restrictive zoning (resource sterilization), and the difficulty of developing and permitting production sites for aggregate.

Jan 1, 2004

By P. C. Fletcher, E. Kaya

The Bond grindability testing procedure has been standardized to measure the same grindability values, i.e. Bond work index (BWi), for the same ore when tests are performed in different laboratories or by different operators. This is accomplished by the standardization of mill dimensions, tumbling speed, grinding ball charge weight and distribution, sample ore charge weight in the mill and operating practice. The results of this investigation reveal that the Bond work index grindability values may differ substantially with different standard Bond ball mills. This paper will review the results.

Jan 1, 2002

By A. Wahab Khair, John G. Oldsen, John C. Stankus, Song Guo

During the last several years, implementation of trusses, in lieu of wood cribs, has been successful for supplemental tailgate support in the Pittsburgh seam. This paper reviews, the truss support system provided by the new high strength 0.6" tensioned cable truss, which is now also being used in cribless tailgates. Cable loading and roof deformation were monitored to evaluate roof and floor performance. The test results indicate that the cable truss system successfully controlled the roof and floor during the first and second panel extraction. This paper will describe the advantages of cable trusses and their load transfer mechanism as well as mine evaluation.

Feb 24, 1997

By Peter Campi, Harry R. Asche, Ian P. Callow, Edmund G. Taylor, P. Scott Smith

The US$1,850 million EastLink project is a 39km tollway and includes twin 3-lane,1.5km long, undrained driven tunnels. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and so to help preserve the unique flora and fauna in the area. This paper describes several of the key issues in the tunnel design and construction, including: the integration of the temporary support design with the Contractor’s tunnel excavation and support procedures, including sharing of responsibility between the Designer and Contractor for support type selection and the production of a project specific rock mass classification system to enable more objective determination of ground conditions. detailed hydrogeological assessments during the design and construction phases to allow confirmation of design loads for the tunnel lining design and the various suite of waterproofing tools in order to meet the project inflow requirements. development of a pre-cast invert solution to the main tunnel secondary lining to enable faster lining construction and to minimize risks to the tunnel membrane associated with fixing reinforcement and construction traffic.

Jan 1, 2007

By F. D. Fox

The Flambeau and Ridgeway Mines, both owned and operated by wholly owned subsidiaries of Kennecott Minerals Company, were located very close to populated areas having initial concerns about health, safety and the environment. The success of both operations depended upon developing a framework of community support and enhancing sustainable development opportunities throughout the entire life cycle of the mining operations to address these concerns. The protection of the Flambeau River was the cornerstone of the Flambeau Mine’s success. The highest priority for the Ridgeway Mine was to ensure long-term physical, chemical and ecological stability of the reclaimed mine site. Both of these goals have been achieved and are discussed in this paper, which highlights Kennecott Minerals Company’s integration of sustainable development principles into its business decision-making and management processes.

Jan 1, 2003

By Bruce Cavender

Historically, the processing function has been regarded as efficiently managed as long as production costs were kept low, recovery was adequate and sufficient plant capacity was avail-able. In this paradigm, processing is viewed as capable of making only a limited contribution to a company?s competitive advantage. However, the processing function can provide a primary vehicle for building critical competitive capabilities. Processing organizations should be encouraged to become so accomplished they generate new opportunities for other functional groups and thereby influence a company?s overall strategy. This requires a deep shift in processing?s role, in its self-image and in the expectations of it held by managers in other functions. Specific plant improvement techniques ? total productive maintenance (TPM), loss control, etc. ? should be viewed primarily as means for building strategically valuable processing capabilities. Different improvement strategies create different kinds of capabilities and present new strategic options. Broadly speaking, a mineral-producing company seeks competitive advantage through two principal activities: the development of new mineral production and reserves and the optimization of existing operations. These lead to increases in ore reserves, production levels and cash flows that are manifested in increased profitability and, hopefully, increases in the price of the firm?s stock. The profitability of a minerals company is a function of the overall profitability of the industry sector in which the company participates and the firm?s competitive position within that sector relative to those of its competitors. Competitive advantage within the industry comes from two sources: the ability to maintain lower prices than competitors for the same product (cost leadership), or from the sale of products with unique properties that justify higher prices (product differentiation; Porter, 1980). Most mineral companies produce fungible commodities that are sold to anonymous customers, and sustainable cost advantage is the only long-run strategy available to these companies to enhance profitability.

Jan 1, 2008

By G. Budge

In the extractive industry the term ‘continuous improvement’ (CI) usually means procurement of the latest state of the art equipment. This is generally perceived as the only way to add further value to the supply chain, with the driving philosophy of increased tonnage to dilute operational costs. However, not all market places can facilitate this approach. RJB lives in a fiercely competitive market and has targeted the standard efficiency drivers of rationalisation and stock management with a vengeance; and also operate CMMS (Computer Maintenance Management System), RCM (Routine Condition Monitoring)and CBM (Condition Based Maintenance) methodologies. Ultimately though, these systems are only as good as the people who operate and manage them and to add further value without procurement, people must be re-introduced back into the operation. Through TPM (Total Productive Mining), that is what RJB have set out to do.

Jan 1, 2001

By L. J. Prosser, A. T. Iannacchione

Unfortunately from 1991 through 1995, 44 miners were fatally injured in the stone industry. Of these 12 occurred at underground mines from a total work force of less than 2,000 miners. Nine of these 12 miners were fatally injured in falls of roof or rib. A safer environment for the miners can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground control strategies. Roof and rib conditions in the underground stone industry were observed and assessed at 33 mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania, and West Virginia [(Figure 1)]. Hazard assessment indicated that those ground failures occurring under moderate to substantial overburden (> 30 m [l00 ft]) were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine layout decisions tremendously influence ground stability.

Feb 24, 1997

By L. E. Beverage

In 2006, the Mine Improvement and New Emergency Response Act (?2006 MINER Act?), Pub. L. No. 109-236, 120 Stat. 493 (2006) was enacted in a bi-partisan move to strengthen the 1977 Mine Safety and Health Act. This action followed several underground coal mining accidents at the Sago and Aracoma Mines in West Virginia and the Darby Mine in Kentucky. The focus of that legislation was, in part, to force technological development and implementation. It involved the recomposition and training of rescue teams. Requirements for sealing worked out areas of mines were changed when MSHA invoked its Emergency Temporary Standard (?ETS?) authority for the first time in many years. Increased penalty amounts were established for certain types of violations for all types of mining, and minimums were set for unwarrantable failure violations issued under Section 104 (d)(1) and (d)(2); 30 U.S.C. Section 814 (d)(1),(2). The entire 30 C.F.R. Part 100 penalty criteria was revamped in a rulemaking, effective in April 2007. The visions were ambitious and noteworthy and those in industry and government have spent the last four years working through the aftermath of intended and unintended consequences of these changes. The penalty structure arrived at in 2007 has proven unwieldy and has contributed to the increase in contested caseload now before the Federal Mine Safety and Health Review Commission. In essence, litigation under the Mine Act ground to a virtual halt when the number of cases increased but the budget for Administrative Law Judges, who hear the cases, and the Solicitor?s office who represents MSHA, was not increased. Addressing the backlog effectively was one of the major challenges when Joe Main was confirmed as Assistant Secretary in early 2010.

Jan 1, 2011

By Gene Mattila, Ron Boyd

Introduction Rock bolting is a general term that encompasses pinning, roof bolting, rib bolting, and cable bolting. Rock bolting contributes the highest nonproductive cost and is the most significant safety risk in mining today. Total installed bolt costs are now more than $20 per bolt. Rebolting or repair work doubles this. And bolting accidents account for about 30% of all fatal and nonfatal lost time accidents. It is only logical, then, for the mine operator to install the highest quality anchors possible. Every bolt on the market - tensioned, untensioned, full contact, or point anchor - has designed capabilities in axial, shear, and fluctuating ground conditions. Bolts will provide a designed support if material specifications and installation procedures fall within the manufacturer's recommendations. This also assumes that there are no unexpected geological or operational changes. Proper material specifications and installation procedures should guarantee the mine operator a quality anchor. To help assure this, the Mine Safety and Health Administration (MSHA), the US Bureau of Mines (USBM), and the AMC Manufacturers group developed stringent ASTM materials standards. These govern mechanical point anchor bolts and bolts using threaded and nonthreaded rebar. There are also minimum standards that suppliers must comply with in the manufacture of frictional bolts. However, most frictional bolt standards are based on the manufacturer's own specifications. It would be impossible to set uniform regulations on frictional bolts. Each bolt provides support in a slightly different manner and thereby requires different material needs. Quality Control In any case, material quality can generally be assured through tight order specifications and periodic quality control checks. The problem with installing quality anchors does not solely lie with the material. It includes all the events that occur from the time a bolt leaves a manufacturer to the time it is installed. The anchoring ability of any major type bolt can be affected by transportation, storage, mechanical performance of installation equipment, installation demands of the operator, proper drilling accessories, and local geology. Table 1 and Fig. 1 document the negative events that can affect each bolt and the degree to which it can be affected. Drilling a hole of oversized diameter, for example, is an operator controlled factor. It will adversely affect most bolts. An over-sized diameter reduces, or even eliminates, the anchorage capability of a mechanical shell. It will reduce the support capacity of a split set to nearly nothing. And it will cause a partial or incomplete grouting around the resin bolt. Frequently, due to bit wear, holes are drilled undersized in diameter and may not be properly cleaned out. In this case, it will be difficult for the operator to push the mechanical shell into the hole, thereby causing him to drill another hole. In cases where the bolt is obviously not providing anchorage, operators will probably drill another hole and place another bolt. Rock Bolt Regulations It is the situations where a bolt is improperly installed in the hole, but gives the appearance of a good bolt, that are frightening. In fact, some safety officials and engineers believe that only 50% to 60% of installed bolts are working. These bolts cause irregular ground load transfers in other bolts and overload them. This causes hazardous situations and overstressing. It is these bolts that fail prematurely 200 to 255 mm (8 to 10 in.) behind the face and possibly contribute to the high accident rate. The government and several manufacturers recognized the need to check the integrity of rock bolts. These programs are in different stages today. Tight torque regulations have been established for mechanical

Jan 4, 1985

By P. Ulrich, V. Svalbonas

The early to mid 1980s was a period of mining consolidation, and many senior design engineers retired from the mill industry. Similar conditions have existed in the last few years. This creates a loss of a tremendous amount of experience. This paper is a look back by two senior mill designers who survived the dips in both time periods. From a continuous design practice of over 25 years, mill designs and fabrication practices are surveyed with a view of identifying what works, and is necessary, and what doesn’t, or is not necessary, in the creation of a safe, economic, long-lived grinding mill.

Jan 1, 2001

By Pat Wilmoth, Joseph P. Gildner, Dan Nowak, Shane Yanagisawa, Don Z. Painter, Gordon F. Revey

Frontier/Traylor is presently completing construction of twin tunnels for the Tri-County Metropolitan Transit District of Oregon’s (Tri-Met) westside lightrail system. The tunnels are each 4,550 m (14,935 ft) in length and 6.48 m (21.29 ft) in diameter. The 1/3 of each tunnel was driven from the west portal using drill and blast methods and the remaining 2/3 was driven from the east portal using a TBM. The paper describes: The difficulties encountered by the TBM mining the weathered Columbia River Basalts. The execution of drill and blast work despite challenging ground conditions, stringent noise and vibrations specifications, and public relations problems. The excavation and lining of the Washington Park Station 79 m (260 ft) below the park zoo.

Jan 1, 1997

By L. Yuan

To reduce fire hazards from spontaneous combustion of coal in longwall gob areas, a series of computational fluid dynamics (CFD) simulations were conducted by National Institute for Occupational Safety and Health (NIOSH) to model the spontaneous heating of coal in longwall gob areas. The previous modeling results demonstrate that spontaneous heating of coal usually occurred behind the longwall shields and along the face with a bleeder ventilation system. Assuming a stationary longwall face, the spontaneous heating could turn to a spontaneous fire in several days for the most reactive coal under favorable conditions. When the longwall face advances, the spontaneous heating process will be significantly affected. In this study, the effect of longwall face advance on the spontaneous heating in the gob area is investigated using the CFD model developed in previous studies. One longwall panel with a bleeder ventilation system is simulated. The width of the panel is 300 m, while the length of the panel is changed between 1,000 to 2,000 m. The same permeability and porosity profiles are used for gobs with different lengths. The spontaneous heating first develops in the gob when the longwall face is stationary. Then, the face advances at a certain rate. The face advance is simulated as a series of discrete movements, and the effect of the face advance on the maximum temperature developed during the face stoppage is examined. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

By M. Fan

Froth flotation is the most widely-used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubble on the flotation performances of different particle size fractions of coal was investigated using a bank of 10-liter flotation cells, a specially designed 50 mm inside diameter column and a 152 mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during coal froth flotation process improved flotation efficiency. The use of nanobubble in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.

Jan 1, 2012

By T. C. Pool

Physical and chemical conditions permitting, in-situ leaching (ISL) of uranium offers a variety of advantages over conventional production methods including less surface disturbance and less solid waste. Commercial production of uranium by in-situ leaching techniques was initiated in 1963 in the Shirley Basin of Wyoming by Utah Construction. On a world-wide basis, ISL uranium production amounted to about 13.2 million pounds U3O8 in1999, approximately 16% of world output. Both acid and alkaline systems are used, the selection of which is primarily dependent upon groundwater quality and related reclamation requirements. ISL offers low capital costs per unit of annual capacity and is particularly flexible in adapting to changing market conditions.

Jan 1, 2000