Search Documents

By Vinay Kumar, Manis Kumar Jha, J. Rajesh Kumar, Archana Kumari, Rekha Panda, Jin Young Lee

Rare earth metals (REMs) play a significant role in the manufacture of permanent magnets, fluorescent lamps, catalysts, medicines, super alloys etc. Recently, China, which controls 97% of world trade in REMs, imposed restriction on its export. Consequently, the global demand of REMs is escalating and is expected to exceed the supply by 40,000 tonnes annually. Present review paper reports the flow-sheets of commercial processes based on pyro-hydro and hybrid techniques as well as systematic research for process development to recover REMs from primary and secondary resources. This review paper also reports the recommendation and future prospective to fulfill its demand and supply gap keeping in view environmental prospective.

Jan 1, 2014

By Xuemei Zheng, Aiyuan Ma, Guojiang Li, Tingfang Xie, Jinhui Peng, Libo Zhang

A new microwave roasting technology for the removal of Cl from zinc oxide dust is proposed in this paper. The effect of important parameters, such as roasting temperature, holding time and stirring speed, were investigated and the process conditions were optimized using response surface methodology (RSM). The experimental results show that zinc oxide dust dechlorination rate can reach more than 95.66% and meet the requirements of wet smelting electrolysis when controlling the stirring speed of 60 r/min,roasting temperature of 650 °C, holding time of 30 min. In addition, the effect of roasting temperature and holding time on removal ef ficiency of Cl was most signi ficant. As a result, the Cl content was decreased without the risk of pollution. This makes it as a good choice for a more ecological treatment of zinc secondary resources.

Mar 1, 2018

By Shilai Yuan, Huimin Lu, Panpan Wang

A big andalusite ore bed was found in Dingxi District, Gansu, China. In this paper, the feasibility of producing solar grade silicon from aluminum-silicon alloys by carbothermal reduction of andalusite ore was studied. First, the carbothermal reduction experiments were conducted in a 100 kVA DC submerged arc furnace with reducing temperature 2000–2200 °C and reducing time 4 h, the hypereutectic aluminum-silicon alloys containing 50–55 mass% aluminum and 35–45 mass% silicon were obtained; then the investigation on solidification of the hypereutectic Al-Si melts under the temperature gradient as an intensified separation silicon way was carried out. According to previous investigation, the optimized technical process for solar grade silicon and eutectic Al-Si alloy from andalusite ore was proposed.

Mar 1, 2017

By W. -S. Hwang, R. A. Stoehr, P. Ingerslev

"The flow of molten metal entering complex two-dimensional foundry molds has been modeled using the Simplified Marker and Cell (SMAC) and Solution Algorithm (SOLA) techniques. The molds were for a series of four and three-spoke wheel designs. The computer calculations were compared to physical experiments in which molten cast iron was poured into C02-bonded sand molds. The metal was photographed with a high speed motion picture camera focused through a Pyrex glass window on one face of the mold. To get good agreement between the calculations and the experiments, it was necessary to accurately represent the velocity through the ingate. This was calculated by application of the Bernoulli equation to flow through the feed system. Some difficulties were experienced with mathematical instability, expecially in the three-spoke design with a narrow ingate. This was overcome by using 100% upwind differencing, and over relaxation parameter near 1.0 (i.e. no over relaxation), and variable mesh spacing.IntroductionModeling the flow of molten metal entering molds has the potential for making significant contributions to the design of feed systems. It will supply information to the computer-aided-design systems of the future that will enable the designer to optimize the placement of gates, dimensioning of passages, and designation of casting speeds. Such design criteria have generally been based on application of energy balance (Bernoulli equation) principles to flow in the sprues, runners, and gates. Indeed, this is the easiest way to determine the proper dimensions to give a suitable filling time for a casting of a given size. A number of computer programs, including one by some of the present authors, have integrated such calculations into CAD systems. l Modeling the flow of metal inside the mold cavity requires other techniques that will handle free-surface transient flow. Stoehr and Hwang reported on the application of the Marker-and-Cell (MAC) technique to mold filling problems at the previous conference in this series at Hennicker, N.H. in 1983. 2 Although considerable progress has been made since that time in improving the accuracy, stability, and convenience of these techniques, the shapes to which they were applied remained limited. Also, physical verification of the results of the calculations was limited to water models.The work to be reported in this paper was undertaken with two objectives: (1) to apply these techniques to more complex and realistic shapes, and (2) to verify the results by comparison with flow patterns observed in molten metal poured into actual sand molds."

Jan 1, 1986

By David A. Neudorf

Known resources of nickel laterites considerably exceed nickel sulfide resources and there is a growing consensus that most new nickel production will be sourced from laterites. The development of nickel laterite projects is very capital intensive due to inherently low grades, inability to concentrate ore prior to processing, complex processing technology and typically large infrastructure requirements. This has resulted in most recently proposed projects being "mega-projects," to achieve economics of scale. However, this may result in unacceptable project risk in many cases. Furthermore, many known laterite resources are not large enough to support a mega-project. This paper describes an alternative model for nickel laterite project development that allows, smaller scale and reduces capital exposure. The requirements of this model in terms of process technology, infrastructure and commercial innovation are described. Keywords: Nickel, Laterite, Project, Economics

Jan 1, 2004

By M. Pakala, Z. Fan, Ray Y. Lin

Deposition of hard chromium coatings using electrodeposition is accompanied by emission of hexavalent chromium mists which is a carcinogenic. Hence alternative chromium deposition technologies are being investigated. Sputter deposition is a strong candidate to economically deposit hard chromium coatings in an environmentally friendly way. Chromium coatings of 2-3 µ m thickness were deposited on plain carbon steel coupons using RF magnetron sputter deposition. Depositions were carried out with 0 to 22 vol% nitrogen in the plasma. Structure of the coatings was studied using x-ray diffraction analysis With increasing nitrogen contents, formation of the two nitride phases was observed. The pure chromium phase was detected in coatings with up to 7% nitrogen in the sputtering gas. The solid solution of nitrogen in the pure Cr phase coating was identified by shifts of Cr x-ray diffraction peaks to higher d-spacing. The microhardness of the coatings deposited at a substrate temperature of 200°C showed an increase in hardness with increasing nitrogen content from 600 kgf/mm2 (5.9 GPa) at 0% nitrogen to I250 kgf/mm2 (I2.25 GPa) at 9.5 % nitrogen and a subsequent decrease in hardness to I 100 kgf/mm2 (11 GPa) beyond 9.5 % nitrogen in the sputtering gas. This corresponds to the formation of the hard Cr2N phase, at 9.5 % nitrogen, and CrN phase, at I5.7 % nitrogen. The reported bulk hardness values of Cr2N and CrN are I600 kgf/mm2 (I5.7 GPa) and I 100 kgf/mm2 (11 GPa) respectively. For pure Cr phase coatings, there is a slight increase in hardness for coatings deposited at 7. I % nitrogen from that without nitrogen in the sputtering gas. This could possibly result from the solid solution strengthening of the Cr lattice by nitrogen. For films deposited at 200°C, phases of the deposited films seem to be the overwhelming factor in controlling the microhardness.

Jan 1, 1998

By P. M. Tyroler

Inco operates a hydrometallurgical plant to treat the residue from the pressure carbonylation process. The main constituent in the residue is cop¬per. The residue is leached under pressure in an acid sulphate solution in two stages and the copper is recovered via electrowinning. The electrowinning tankhouse is fully integrated into the overall plant flowsheet as spent elect¬rolyte is required in upstream leaching steps. In recent years, the amount of residue had increased and copper removal capacity became the rate limiting factor for the entire plant. Consequently, a major program was undertaken to upgrade the tankhouse with regards to capacity, efficiency, cathode quality, working environment and structual integrity and appearance. This paper will describe current facilities and operation, and detail progress in our up¬grading efforts.

Jan 1, 1987

By C. Coetzee

Additives are commonly used in copper electrowinning to improve cathode morphology. Polysaccharides such as guar are generally favoured as additives due to their compatibility with solvent extraction. Polyacrylamides are, however, being considered as possible alternatives. Understanding the influence of the structural chemistry of additives on electrowinning performance is critical to utilise them efficiently. This paper investigated polyacrylamide additives which are structurally different; their effects on copper electrodeposition were characterized and compared to that of guar. Electrochemical impedance spectroscopy (EIS) were used to characterize the effects of molecular weight and ionic charge of the polyacrylamides on electrodeposition. The findings were compared against results obtained with an industrially used guar product. Equivalent circuit modelling of EIS data indicated that an increase in polyacrylamide concentration and a decrease in additive molecular weight increased the overall system resistance.

By T. Thuy Minh Nguyen, Sathish K. Lageshetty, Paul Bernazzani

The addition of nanoparticles to epoxy resins often results in changes in the physical properties of the material particularly when dealing with thin coatings. By characterizing the mechanism of interactions between nanoparticles and polymer chains the material could be tailored for specific applications or properties such as enhanced biodegradability. This study compared the characteristics of common DGEBA resin coated on a silicon substrate and embedded with nanoparticles of TiO2 and Fe2O3. Specifically, we investigated the rate of curing, and the thermal stability of these nanocomposites. Results show changes in the stability for compounds containing TiO2, while Fe2O3 significantly enhanced the curing rates of the nanocomposites while maintaining similar physical properties.

Mar 1, 2017

By H. Y. Sohn, Joshua E. Ramos, Moo Eob Choi

"A new technology for ironmaking based on direct gaseous reduction of iron ore concentrate is under development. This technology would drastically lower CO2 emission and reduce energy consumption by nearly 38% of the blast furnace requirements. Experiments were performed using iron oxide concentrate at 1150oC in a bench-scale facility, which was the highest temperature that could be reached in the facility. The reduction extent was determined at residence times of 3.5 - 5.5 seconds in which the reduction extent approached 43% with 0% excess H2 and 95% with 860% excess H2. Separate kinetics measurements showed that the rate is much faster at 1200 - 1400 oC. Experiments were also carried out using syngas (mixtures of H2 + CO). About 90% reduction in 3.5 seconds with 860% excess hydrogen contained in the syngas demonstrated sufficiently fast reduction for a suspension process and the feasibility of usingsyngas instead of pure hydrogen.IntroductionDespite the improvements in the modern blast furnace (BF) process, it suffers from many drawbacks. The process requires the feed in the form of sinters or pellets and high-grade coking coal. Thus, BF iron production is projected to decrease gradually [1]. The main factors for this are the environmental regulations [2] and the high capital investment cost.A large number of new ironmaking technologies have been developed or are under development [3]. Most of these processes, however, are not sufficiently intensive to replace the blast furnace because they cannot be operated at high temperatures due to the sticking and fusion of particles. Therefore, a new technology is under development for producing iron directly from fine concentrates by a gas-solid suspension technology, which would reduce energy consumption by about 38% of the amount required by the blast furnace and drastically lower environmental pollution, especially CO2 emission, from the steel industry."

Jan 1, 2009

By J. A. S. Tenorio, K. S. Barros, D. C. R. Espinosa

Considering the risks involving the use of cyanide, other complexing agents have been evaluated for the treatment by electrodialysis of the effluent of brass electrodeposition and among them, EDTA is interesting since it has been already tested for many years to separate ions. The main objective of the present paper was to evaluate the occurrence of fouling and scaling on the surface of the anion-exchange membrane HDX 200 by the construction of chronopotentiometric curves and speciation diagrams in different conditions (pH between 10–12 and proportion of cupric ions of 30%, 50%, 70%). According to the results, the chronopotentiometric curves did not show additional inflexion points typical for the cases which occurs fouling and scaling for the pH values evaluated, which is in accordance with the speciation diagrams of the solutions constructed with the aid of Hydra-Medusa software. Hence, the pH and the proportion of cupric ions did not show influence on the curves behavior.

Mar 1, 2018

By Won C. Park

Experiments showed changes in the mineral content of dolomitic oil shale at temperatures and exposure times which bracket conditions encountered during in situ retorting. Laboratory results correlate with cores from a spent in situ retort at Occidental's Logan Wash test site at Garfield County, Colorado. Dolomite, CaMg(CO3)2, decomposes rapidly to form periclase, MgO, calcite, CaCO3, and CO . Both calcite and periclase are intermediate products that can be stabilized by CO atmosphere at lower temperatures, while steam accelerates the formation 2 of silicates. The decarbonation of calcite appears to involve a direct reaction with both quartz and periclase in forming these silicates. Decarbonation preceeds the formation of akermanite, Ca2 MgSi 207, and diopside, CaMgSi 206, within several hours of heating and is followed by the nucleation of forsterite Mg2SiO4, and monticellite, CaMgSiO4. Under in situ retorting conditions, akermanite and diposide are the major minerals above 800°C. Equilibrium is not attained within 200-300 hours. In situ retorting temperatures above 800°C for extended periods of time should reduce potential ground water leaching by the formation of silicate minerals. These silicates are less soluble than free lime, magnesium or alkali oxides. There is a corresponding decrease in the natural pH of these silicates from approximately 12 down to 7.5 to 9:

Jan 1, 1981

By Nobumasa Kemori

Six kinds of copper '90ncentrates. were treated individually in a ,pilot scale. Outokumpu flsah smelting furnace ~n order to study their ?flash smelting behavior with respect to oxygen efficiency and dust generation. The copper concentrates tested were selected from the more than twenty sources which are treated at the Sumitomo Toyo copper smelter, so as to provide a wide range of chemical composition in terms .of Cu, S,Fe, Pb + Zn + As, and Si~ content. Oxygen efficiency 'and dust generation rates obtained in 'the experiments ranged from 80% ,to 108% and 11% to 20%, respectively. Relationships between these results and experhnental conditions such as chemical and mineral composition of the copper concentrates, flux ratio, fuel consumption and so on are also discussed quantitatively in this paper.

Jan 1, 1998

By Kymberley Worrell

The Cripple Creek and Victor Gold Mine was acquired by Newmont in August 2015. The high grade flotation mill project was commissioned in February 2014. The mill to date has been throughput limited due to mechanical and design issues. In order to create the most value from a throughput limited plant a campaign to provide timely ore characterization was undertaken. A diagnostic leach methodology was developed to determine gold associations by ore type. The resulting associations were then used to characterize feed blend; gold losses and optimize gold production. The diagnostic methodology is presented along with discussion on flotation implications.

By Shu-cai Zhou

"To understand the solidification behavior of austenitic heat-resistant stainless steel (TP34 7) in rotary electromagnetic-field, the influence of electromagnetic stirring in mold (M-EMS) on solidification structure of TP34 7 heat resistant steel in a round billet continuous casting was investigated based on industrial experiments. The results indicate that the excellent billet solidification structure of TP34 7 heat resistant steel can be obtained with appropriate electromagnetic stirring parameters. The solidification structure of TP34 7 heat resistant steel can be remarkably refmed, central porosity and shrinkage cavity can be remarkably decreased and equiaxed grains zone widens was enlarged. The industrial trials verify that the stirring intensity of TP34 7 heat resistant austenitic stainless steel should be higher comparing with plain carbon steel. Due to a higher viscosity, rotating speed of molten stainless steel was 20-30% lower than that of molten carbon steel in the same magnetic flux density.IntroductionIn recent years, the development of ultra super critical (USC) plants is accelerated by the demands of environment protection and energy saving, and USC plants with steam temperature and pressure conditions in excess of 593°C and 24.lMPa respectively were constructed. To achieve the goal, it is important to develop new materials with excellent high temperature strength, superior resistance to oxidation and corrosion at high temperature. Besides, their cost must be low enough to meet the requirement of plants [ 1]. TP34 7H steel is promising austenitic heat-resistant steel, which is used as superheater/reheater tube material and is extensively used for high temperature components and fossil-fired power plants, and suitable to be used in USC boilers plant. This kind steel contains with about 0. 7%Nb and it keeps higher allowable stress and creep rupture strength than TP304 and TP321H [1-2]. TP347H has conventionally been produced by ingot casting followed by forging and rolling. Recently, in order to decrease the production cost, challenging trials to produce these types of alloys by a continuous casting (CC) process have been attempted. However, the solidification structure of austenitic stainless steel is one of the key issues that attract more attention. Due to the low thermal conductivity of TP347H heat resistant stainless steel (much smaller than that of plain carbon steel), pronounced defects during continuous casting of austenitic heat-resistant steel such as coarse columnar, center porosity and coarse bridging, greatly influence mechanical properties of fmished products.A widely used technique in metallurgy is the inductive drive of molten metals using rotational or traveling magnetic fields. Recently, rotary electromagnetic stirring (EMS) has been applied to reducing various defects and improving increase the solidification structure of the metals in the continuous casting of steel, Al-based alloys and Mg-based alloys [3-8]. Electromagnetic stirring of plain carbon and low alloy steel in the continuous casting bloom and slab is well established for improving the quality of cast products [9-11] and is widely used in industry. However, very few literatures on electromagnetic casting of heat resistant stainless steel have reported. In this work, an industrial plant trial was performed to clarify the effect ofM-EMS on the macroscopic quality ofTP347heat resistant steel billet, in which the regularity and mechanism of the influence of EMS on solidification casting billet were discussed."

Jan 1, 2014

By Eric Klaffenbach

Valorization of slag from metallurgical industrial processes becomes ever more important as this may help optimizing and reducing the use of natural resources such as rock and sand. In view of this objective, metallurgical processes have to be analyzed in order to modify the slag composition so that it will meet the expected requirements of potential users of these resources. This paper gives the results of a thermodynamic analysis of the flash smelting process to understand the impact of operational parameters on slag chemistry and elemental partitioning in the process. It is shown that an increase of the matte grade and temperature leads to higher deportment of Pb, Zn and As to the slag. With increasing matte grade the volatilization of these elements decreases. Furthermore, the results indicate an increasing solubility of Cu and S in slag at higher temperatures.

By J. A. S. Tenorio, K. S. Barros, D. C. R. Espinosa

In the last decades, authors have been focused in the development of a cyanide-free bath for the electroplating industry of brass due to the risks that involves the use of cyanide and they have been evaluated the electrodialysis as an alternativemethodforthetreatmentoftheeffluentgeneratedinthistypeofindustry because ofthe limitationscaused bythe chemical precipitation. Hence, thepresent paperaimedtodeterminethelimitingcurrentdensityoftheeffluentgeneratedinthe free-cyanide electrodeposition of copper and zinc using EDTA as chelating agent for the treatment of the effluent by electrodialysis. The synthesized solutions were preparedwith copper sulfate andzinc sulfate indifferent conditionsofpH (10–12) and proportion of cupric ions (30%, 50%, 70%). According to the results, the increase of pH and the cupric ions proportion caused an increase in the limiting current density because of the larger amount of anionic species in solution and the consequent difficult to achieve the concentration polarization phenomenon. (cid:1) (cid:1) (cid:1)

Mar 1, 2018

By Fuqiang Zheng, Yufeng Guo, Pengfei Li, Guanzhou Qiu, Tao Jiang, Andrew Yakovlevich Travyanov

Low content of TiO2 and high impurities content of Ca and Mg are the shortcomings of domestic ilmenite. To meet the requirements of the material in the titania produced by chlorination process and titanium sponge industry, enrichment of ilmenite is necessary. In the process of enriching ilmenite, high temperature and reductive condition were beneficial to the formation of anosovite, but the high content of magnesium oxide which was solid soluble in anosovite baffled the following separation. So the effects of pre-oxidation and reductive conditions including reduction temperature, reduction time and hydrogen concentration on the phase composition and metallization rate were studied. The characteristics of reduction samples were analyzed by X-ray diffraction and optical microscope. Results have shown that the reduction product is mainly composed of Fe, Fe(Mg)TiO3 and TiO2 at 1123K, its metallization rate is about 65%,magnesium exists in Fe(Mg)TiO3.

Jan 1, 2015

By C. Landolt

Inco's Copper Cliff Smelter Complex produces some 11 5,000 tonnes per year of nickel and 120,000 tonnes per year of copper. The Smelter flowsheet has changed a number of times over the years. The most recent changes were effected in the mid-1980's in response to new realities in metal markets and heightened awareness about the workplace environment. By 1994, the flowsheet will undergo yet another metamorphosis as part of Inco's SO2 Abatement Program. The paper discusses the improvements implemented during the 1980's and projects the processing in the Smelter through 1994.

Jan 1, 1993

By A. R. Laplante

Recent developments in gold metallurgy are used to illustrate how the interface between gravity recovery and hydrometallurgy has evolved in recent years. Of particular interest is the use of gravity recovery to produce high-grade concentrates that can be subjected to intensive cyanidation. It is expected that a growing proportion of gold production, possibly close to 50% in certain countries, will follow this route. Other examples of the interaction between gravity recovery and cyanidation are also provided. Implications for new and renewed research directions are discussed.

Jan 1, 2003