Search Documents

By D. Gu, R. G. Anthony, C. V. Philip, M. E. Huckman

"In this paper, we review the equations needed to construct an ion exchange column model. These models contain three major components: 1) a differential material balance around the column, 2) a differential material balance around an ion exchange particle, and 3) a constitutive equation for diffusive flux. We then examine the ability of a fairly simple mathematical model to predict ion exchange column experimental data. This model contains the traditional absorption theory equations and is used to predict the behavior of a column filled with a hydrous crystalline silico-titanate and which is removing trace amounts of Cs+ from a high pH, complex electrolyte solution. Finally, we propose replacing Fick's law with the Nemst-Planck equation as the constitutive equation for diffusive flux. We use a NemstPlanck type model to predict batch experimental data, then evaluate it by comparing it's ability to predict experimental data to that of a more traditional Fick's law type model. The data from this comparison suggests that the Nemst-Planck type model yields better results.IntroductionMillions of gallons of strongly basic, radioactive waste are currently stored in underground storage tanks at Hanford and Savannah River and several locations within the United States. Due to the limited life expectancy of the tanks, there is a pressing need to remediate these wastes. This need has prompted the recent development of new ion-exchange materials for removing radioactive elements from aqueous solutions. A novel material called TAM-5 has been developed jointly by Texas A&M University and Sandia National Laboratories. TAM- 5, a crystalline silico-titanate, is highly selective for Cs + in the complex electrolytic solutions typical of these wastes. It is stable in very basic solutions and in radioactive environments [1, 2 ,3]. In laboratory testing to determine the selectivity of various materials, TAM-5 was superior to other candidate ion exchangers [4, 5]. The selectivities were determined by measuring a distribution coefficient, Kd, which is defined as the concentration, gig or mmols/g of Cs in the solid phase divided by the concentration, mg/L or mmols/mL, of Cs in the liquid phase. The units of Kd are ml/g or L/kg. Table 1 shows Kd values for TAM-5 compared to 9 other candidate materials in a typical waste solution [6]."

Jan 1, 1996

By Mitsutaka Hino

The contents of gangue minerals, such as A1203, P205, crystalline water and so forth in the iron ore imported to Japan tend to increase year by year, Though the increments of such gangue contents are approximately 0.1-0.2 mass%, some problems for the blast furnace operation in ironmaking process have already been reported, In order to clarify the mechanism of harmful effect caused by the small increment of gangue minerals, mainly A1203, on the blast furnace operation, the dripping behavior of FetO-CaO-SiO2-AI2O3-MgO slag from the iron funnel, which simulated the micro-porosity in sinter ore, has been observed with the wide range of basicity, Al2O3, FetO and Mgo contents. The effect of MgO on the dripping behavior of slag has been summarized in this paper, It was found that the addition of 2mass% MgO resulted in large increase of hold-up on the most of the conditions. When FetO content was less than 20mass% and the basicity was lower than 0.8, MgO lowered the hold-up even if the slag contained 10mass% Al2O3. Every slag hold-up showed the minimum at the basicity of less than unity on the conditions of constant FetO and A1203 contents. This trend became remarkable when the slag contained 2 mass% MgO.

Jan 1, 2003

By Ping Long, Bin Yang, Jian Wu, Xiumin Chen, Wenli Zhang

In this study, the analysis method of trace element in pure indium using glow discharge mass spectrometry (GD-MS) has been established by correcting the analysis result, which was obtained from non-standard quantitative method of GD-MS. The effect of instrument operating parameters, the resolution and isotopes and the pre-sputtering time on the determination results were investigated respectively. The optimized operating parameters of the instrument were obtained as follows: the discharge current was 37.5mA and discharge airflow was 475ml/min. Mass spectral interferences have been eliminated using selected resolution and isotope. The pre-sputtering time was 30 min. 4 trace elements in two pure samples were determined for 6 times. The RSD were less than 20%. The content of trace elements in indium samples was determined by GD-MS and Chemical Analysis Method of Indium which is tested by inductively coupled plasma atomic emission spectrometry, respectively. The results were consistent with each other.

Jan 1, 2016

By Shigeatsu Nakazawa

Activities of Bi and In in the Bi-In liquid alloy were measured over the whole range of composition at the temperatures from 850K to 1050K. An alloy was vacuum-sealed in a quartz cell and heated at the temperature of interest. The absorption for 307nm radiation from Bi lamp was measured for Bi atom vapor in the cell. By heating a pure metal as a standard and measuring the absorbance as a function of the temperature, an analytical curve for Bi atom vapor was constructed and used for conversion of the absorbance to the vapor density. Bi activity was determined as the ratio of the Bi atom vapor density over the alloy to that over a pure metal. The same procedure was applied to the In 304nm radiation from In lamp and In activity was determined independently of Bi. Results showed that the liquid Bi-In system behaves like a regular solution.

Jan 1, 2003

By Dean Ilievski

Mathematical modelling of the precipitation process requires that the kinetics of crystal growth, nucleation and agglomeration be known: This paper reviews the current state of knowledge on these precipitation sub-processes (ie. growth, nucleation and agglomeration) and describes a number of experimental techniques for estimating their kinetics. The experimental methods used to generate the precipitation data and the data analysis techniques used to extract the kinetics information from the data are discussed separately. There is no universal "best" technique for determining the kinetics. However, studies on multi-crystal systems are more reliable for modelling purposes than are single crystal studies. The selection of a technique will depend on which sub-processes are present. A problem with all kinetics studies is that there is generally a large uncertainty in the estimated kinetic parameters. This stems from the scatter in the experimental data being further propagated by the mathematical techniques used to extract the kinetic parameters.

Jan 1, 1996

By F. -Z. Ji

Carbon injection into metallurgical slag is important in electric arc furnace (EAF) steelmaking for foamy slag practices and in nonferrous slag cleaning operations. The current publication presents kinetic data for coal injection into EAF slag to understand the interaction between injected carbon and metallurgical slag. Coal particles were injected into EAF slag and the kinetics were followed by gas and slag analysis. The results were analyzed, in terms of fundamental rate equations for each possible reaction step, as a function of temperature and slag composition.

Jan 1, 2003

By Xuling Chen, Zhiyun Ji, Min Gan, Wenqi Li, Xiaohui Fan, Zhiyuan Yu

"Specularite and vanadium-titanomagnetite are difficult to granulate, and with the increase of their proportions, the permeability of sintering bed is deteriorated together with the combustion velocity of fuel for the shortage of air through the sintering bed, which can lower sintering speed and specific production capacity significantly. The biomass fuel has a higher combustion velocity than coke breeze, therefore the productivity of specularite and vanadium-titanomagnetite ore can be improved remarkably by replacing coke breeze partly with biomass fuel .The results showed that, when the proportion of biomass fuel replacing coke is 40%,the sintering speed and specific production capacity of 35% specularite were improved from 19.06mm/min, 1.33 t/(m2·h)to 21.45mm/min, 1.47 t/(m2·h),and that of 55% vanadium-titanomagnetite were improved from 17.23mm/min, 1.11 t/(m2·h)to 22.80mm/min, 1.44 t/(m2·h). As a conclusion, biomass fuel is effective to strengthen sintering of refractory iron ore.IntroductionThe iron and steel industry of our country has achieved significant development in the recent years. In 2010, the output of steel has reached to 0.627 billion tons. The increasing scale of iron and steel has led to rigorous domestic iron ore environment, and the reserves of hematite and magnetite that have superior sintering characteristics are on the decline with continually exploiting and utilizing [1]. Therefore, the RIO (refractory iron ores) SP (specularite) and VT (vanadium-titanomagnetite) have to be applied vastly. However, the quality of sinters can be deteriorated when utilizing RIO in high proportion due to their poor granulation and metallogenic performances [2, 3]. Generally, the ratio of SP is 3~5%,which should not exceed 10% in our country currently [4]. Though high rate of VT is adopted in PZH steel for a long time, the productivity is obviously low compared with normal sintering [5]."

Jan 1, 2012

By Jan Vrestal, Josef Tomiska, Pavel Broz

"Thermodynamic investigations on fcc solid ternary Fe-Ni-Cr alloys have been performed by means of the computer-aided Knudsen cell mass spectrometry. Ternary T.AP.-series (Thermodynamically adapted power series) are used for the algebraic representation of the thermodynamic excess properties. At 1650 K the molar excess Gibbs energy GE is negative over the whole field of stable fcc phase. The molar heat of mixing HE is exothermic in the predominant part of the fcc phase field. Only between the section with a constant ratio of mole fraction Xcr/XNi = 0.64 and the fcc phase field boundary the HE values are slightly endothermic. The results of this work can be used successfully for phase diagram calculations.IntroductionThermodynamic investigations on multicomponent alloy systems such as the Fe-Ni-Cr ternary system including the three binary boundary systems are very time-wasting and usually beset with considerable experimental difficulties. Additionally, the required experimental equipment is very expansive and the obtained results are not always satistying. Therefore it is understandable that many phase diagram calculations are based only on few experimental values of the molar excess free Gibbs energy GE. Consequently, Kundrat and Elliott [1] as well as Hillert and Qiu [2] used in their reassessments of the phase diagram of the Fe-Ni-Cr system thermodynamic data mainly assumed and/or optimized by means of various reasoning.Lee [3] reported recently, a revision of the used thermodynamic description of the Fe-Ni liquid phase is necessary to obtain a better agreement with the experimental data on the bcc/liquid or fcc/liquid tie lines and liquidus temperatures in the Fe-rich region of the Fe-Ni-Cr ternary system than in the previous assessments. This is 'in full agreement with mass spectrometric investigations of Fe-Ni alloys in the liquid and in the fcc solid phase, published earlier [4,5]. Indeed, phase diagram calculations based upon the molar excess free Gibbs energies GE obtained in these studies yield liquidus and solidus lines in excellent agreement with experimental phase diagram data [5]. Nevertheless, these experimental data have not been considered later on any more, not even in the revision by Lee [3]."

Jan 1, 1996

By T. R. A. Davey

The technologies of lead, zinc and tin extraction have made varying degrees of progress over the past twenty years. Producers of all metals have faced increasing demands for reduction of pollution and environmental degradation, and the level of public concern is rising rather than abating. New processing techniques must therefore be not only economically feasible, but politically acceptable, even when the demands of "conservationists" and ?environmentalists? are unreasonable. A new generation of processing techniques has come into being, which do not rely on an expensive sintering stage, nor use metallurgical coke, which is difficult to make without serious pollution. They utilise intense reactors, conveying materials from one stage to the next preferably within an enclosed space, obviating fume emissions, and avoiding heat losses as far as possible. The acceptability of the new techniques? is increased if lowgrade or complex materials can be treated, along with a variety of returns and wastes. In addition, a good selling and servicing organisation seems to be as important as good process technology in determining the spread of the new processes. In the field of pyrometallurgical refining the need is for more general application of several recently developed techniques rather than a search for alternatives to the existing process technologies. However, there is a need for fundamental work investigating the phenomenon of oxygen anode overvoltage in the electrolytic zinc process, in order to make progress in the further reduction of energy consumption. There is also scope for further development and application of vacuum distillation to up-grade thermally produced zinc. This paper presents a personal view of processes which should be developed to overcome existing problems, as we approach the turn of the century,

Jan 1, 1990

By Yasuo Ojima

The mainstream of copper smelting processes in the world today is a combination of Outokumpu type Flash smelting and PS (Pierse Smith) converting process. Presently it can be estimated that about 50% of the worldwide copper production is produced by the Flash smelting process and 80% by the PS converting process. PS converting process due to its operational flexibility and despite its batch character of operation has been widely used in many smelters for more than 100 years. However, an environmental issue has been pointed out related to this process because of the difficulty of handling the fugitive gases. Recently several copper smelters in the world have been newly constructed and others have executed major modification and modernization, The continuous converting process has been applied in many of them instead of PS converting process. This paper compares PS to the emerging continuous converting process and makes a prospect of the future of the copper converting process.

Jan 1, 2003

This report presents overview of the authors' results of thermodynamical investigation of some important metallurgical processes and phenomena. Among them: carbo thermal reduction of silica, and boron oxide, silicon carbide obtaining from different precursors, investigations on copper and manganese ores processing, investigations on pollution from different sources. Special attention is paid-to thermodynamical approach to investigation and estimation of multi component multi element compositions stability, developed by the authors. Also are discussed some auxiliary but' important for the thermodynamical investigations issues.

Jan 1, 1997

"In this paper, a mobile heat treatment furnace from Akkermans Gloeitechniek, a Dutch company, was simulated with Computational Fluid Dynamics (CFD). The furnace is cylindrical with four oil burners, and large metal products such as dredging pumps and impellers can be flexibly heat treated to obtain required microstructure and mechanical properties through stress relief, annealing, hardening and tempering. The furnaces are exposed to the open air, and thus the heat loss becomes significant and varies from day to day and from season to season. Since the temperature of the metal products to be heat treated can only be measured on the surface, the temperature evolution inside the metal could not be tracked in practice. CFD simulation provides a useful tool to predict the temperature evolution within the metal pieces and within the combustion space of the furnace. Energy distribution and heat loss can be subsequently estimated. An overall energy balance through temperature measurement indicted relatively low energy efficiency. Especially during the soaking period, the high energy supplied is barely used to compensate the heat loss of the furnace to maintain a constant temperature of the metal piece. The current CFD modeling aims to give advice on how to modify the design and optimize the operation to reach higher energy efficiency and low heat loss. The CFD model consists of turbulent combustion model, radiation model in participating media, and conjugate heat transfer between the combustion space and solid metal. Temperature measurement was carried out to provide thermal boundary conditions and overall energy balance of the operation. After the model validation with temperature measurement within the combustion space and metal surfaces, furnace optimization will be conducted.IntroductionHeat treatment is a common practice in metal production and manufacturing industries. Through heat treatment at certain temperatures with special patterns, unique mechanical properties of the metals and the metallic products could be obtained. ""Akkermans Gloeitechniek"" is a company situated in K.inderdijk, at location of LHC-Holland (www.ihccaland.com), the Netherlands. Heat treatment of metals is its core business. Various type of heat treatment are applied, such as stress relieving, soft annealing and hardening (quenching), tempering, transformation and precipitation. At the company 6 furnaces are in operation and the 7th is being built"

Jan 1, 2004

By E. V. Verhoef

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-lndicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LeA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LeA assessments, thus leading to erroneous results. The suggested approach provides directions for including these external effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003

By E. V. Verhoej

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-Indicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LCA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LCA assessments, thus leading to erroneous results. The suggested approach provides directions for including these extemal effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003

By Leo Brewer, Kazuyoshi Shimakage, Mamoru Mitomo, Toshiyuki Nishimura, Yoichiro Uemura, Shinji Hirai

"In the synthesis process of ß -La2S3 via the sulfurization of La2O3 powder using CS2 gas, La2O2S was formed. This occurred at an initial stage of the reaction for sulfurization temperatures below 973K, and ß -La2S3 was also formed at a shorter period for higher sulfurization temperatures. It was found that the oxygen content in ß -La2S3 powders decreased gradually with an increase in sulfurization temperature. On the other hand, the carbon content in these powders increased gradually with an increase in the sulfurization temperature. Though it has been reported that ß -La2S3 was transformed to Y -La2S3 at 1723K± 50K, the sintered compact of double-phase Y -La2S3 and ß. -La2S3 was formed at a rather higher temperature of 1973K when the synthetic powder of ß -La2S3 containing a high amount of oxygen was used. However, phase transformation of -La2S3 to Y -La2S3 progressed preferentially with a decrease in the oxygen content of synthetic ß -La2S3 powder. The Seebeck coefficient of the sintered double-phase Y -La2S3 and -La2S3 was higher than that of the single-phase Y -La2S3, reported previously.Introduction La2S3 exists in three polymorphic forms that are similar to a series of Ce2S3, Pr2S3 and Nd2S3: a, ß , and Y'. The a -La2S3, which is stable at low temperature, is irreversibly transformed to ß -La2S3 of various compositions in the solid-solution range between La2S3 and La3S4, at 923 ± 50K. The -La2S3 may also be an oxysulfide of La10S14O2. Moreover, the ß .-La2S3 phase is transformed to Y -La2S3 ,which has a Th3P4 structure, at 1573 ± 100K. The melting point of Y -La2S3 is 2398 ± 30K where this temperature is similar to those of common refractory materials such as silica and alumina. Therefore, it can be predicted that y -La2S3 which has a high melting point and a thermodynamic stability due to the strong affinity of La for S, would have &high refractory character and chemical inertness in many molten metals. The y -La2S3, colored vivid faint yellow is stable up to 623K in air, where oxidation starts. y -La2S3 is frequently used as pigments for plastics and paints3. Furthermore, Y -La2S3 which is a semiconductor, is considered to be useful as a thermoelectric conversion materials, because it has a high Seebeck coefficient."

Jan 1, 2000

By S. Seetharaman, Du Siehen

"In the processing of molten metals, it is extremely important to monitor continuously the concentration levels of various minor elements. In the production of common metals like copper, iron and aluminium electrochemical sensors involving solid as well as liquid electrolytes are being increasingly used to measure the concentrations of minor elements. The present paper deals with the electrochemical principles underlying these measurements and the possible errors involved. One of the major difficulties in the case of the solid electrolytes is to correct for the consequences of the electronic contribution to the conduction of the electrolyte.The application of the electrochemical sensors for molten metals processing involves designing of these probes to withstand the industrial operating conditions. In this respect, significant achievements have been made with respect to the design of oxygen probes for liquid metals in general and liquid copper in particular. Some of the salient design features are discussed in the paper. The application of auxiliary electrodes for impurities in molten metals like phosphorus in copper and silicon in iron are taken up. The development of oxygen sensors for slags is given special attention. Recent developments in the field of sensor technology, as applied to metals processing are highlighted.1. IntroductionThe rapid technological advancement today require precise control of the process parameters and the impurity levels. Most of the molten metals processing in industrialized countries are often steered by suitable computer models, either phenomenological or simulations based on theoretical principles. These models often require that the process parameters are continuously monitored so that the progress is followed and modified suitably as and when required. It is common practice to measure temperatures by incorporating temperature sensors at the various strategic points of the reactor. In the case of monitoring the composition changes in the various phases, the method of sampling followed by routine chemical analysis involves a time lag as well as uncertainties in sampling and analysis. In this respect, electrochemical sensors have the advantage of generating accurate data when properly applied and increasing attention is being paid in the development of electrochemical sensors for various common species in molten metals processing. In the present paper, the developments in this area over the years are outlined and typical process applications are discussed. A greater emphasis will be laid on sensors based on oxygen conducting electrolytes and their application to the production of common metals like iron and copper."

Jan 1, 1996

By Ronald Erdmann

Today the BOF filter dusts and sludges are mainly dumped due to their zinc contents. By typically ranging from 2 to 5 % they prevent the filter dusts and sludges from beeing recycled via the blast furnace route. Based on the different discharge kinetics of Iron and zinc during the main blowing period In a bottom stirred BOF a simple and efficient system for recovery allow zinc fractions has been developed. The obtained material Is suitable for recycling without nsc of shell formation In the blast furnace. Different subsequent development steps have been performed. By starling with a very simple lime dependent model the sludge from the BOF off gas cleaning system was collected in two different sludge channel systems. This model based an the fact that most of the scrap based zinc Is discharged from the melt within the first eight to ten minutes of the BOF process. To Improve the system a spectroscope zinc sensor was Installed at the hot section of the off gas cleaning system to get more reliable informations on the actual zinc concentation of the BOF dust. By use of the system up to 50 % of the BOF sludge can be recycled.

Jan 1, 1995

By Shu Yamaguchi

The behavior of halide impurities in pyrometallurgical processes such as Wealtz kiln and MF process has been discussed based on the thermochemical data and the reported data of PbO activity in PbCl2-PbO melts. The role of PbCl(g) has been estimated to be significant in the chloridization evaporation reaction. From reported data on the PbO activity in PbC12-PbO melts, activity of PbCl2 has been calculated by the numerical integration of Gibbs-Duhem equation, and the stability domains and the composition of the liquid phase as well as the vapor pressure of PbCl2 have been estimated as functions of log P2HCI/PH2O and temperature. From the discussion of the path during cooling process on the log P2 HCI . PH2O vs. temperature diagram, the authors proposed a possible dechioridization process that utilize water vapor as a dechloridizer for the direct precipitation of PbO from gas phase.

Jan 1, 2003

By E. G. Noble

The potential for using heterotrophic microorganisms to solubilize manganese from low-grade domestic ores is being assessed at the Reno Research. center, U.S. Bureau of Mines. More than 90 pct of the manganese has been extracted from a variety of oxide ores in shake-flask tests using molasses as a source of .. nutrients for the microorganisms. It has also been demonstrated that high recoveries of manganese can be obtained from a domestic wad ore using column bioleaching. 'l'he isolation and identification of organisms responsible for manganese extraction is discussed, as are the mechanisms responsible for manganese solubilization.

Jan 1, 1991

By De-qing Zhu, Zi-fu Gao, Jian Pan

"In order to produce high quality metalized products and prevent from burden cohesion during pre-reduction, self-fluxed pellets were made for COREX process in the paper. The effects of reduction temperature and reducing gas composition on pre-reduction behaviors of self-fluxed pellets are studied. The results show that the prereduced pellets have poor quality and deposited carbon appears when the reduction temperature is between 600°C and 700°C. The metallization rate, reduction degree and compressive strength of prereduced pellets are promoted by the elevating reduction temperature and mole fraction of H2. Pellets reduced by pure H2 at 800°C have high metallization rate (96.2%), reduction degree (99.4%) and compressive strength (960N/pellet). In all tests, self-fluxed pellets display normal swelling (RSI<l5%) behavior which reveals that self-fluxed pellets are suitable for COREX process. Increasing reduction temperature and mole fraction ofH2 in reducing gas is benefit for pre-reduction of pellets.IntroductionCompared with Blast Furnace, the COREX process has advantages of short flow sheet, using non-coke coal and high-energy utilization. Acidic pellets and lump ores are the chief iron- bearing burden for COREX process which could lead to low melting point substance appearing in per-reduction process. In addition, the acidic hematite pellets tend to swell during the reduction [1-3]. This will result in decreasing compressive strength of pellets, burden cohesion, bad air permeability and poor work status in shaft furnace. Adding carbonate flux could restrain burden bonding to some extent in actual production, but decomposition of carbonate flux increases energy consumption. Worse still, weak reduction potential is unfavorable to iron material reduction [ 4, 5]."

Jan 1, 2013