Search Documents

By T. A. Sullivan

The work described in this report was undertaken to evaluate and develop techniques for determining the oxygen content of titanium and titanium alloys. Early investigations of volatilization techniques involving halogenation were unsuccessful. Later efforts were concentrated on evaluating vacuum fusion and inert-gas fusion techniques. Two vacuum fusion methods and an inert-gas fusion method were found to be satisfactory in the 0.02 to 1.00 pct., oxygen range. These methods are described in detail. The coefficient of variation by any of the three methods is approximately 5 pct, While the main portion of this paper is devoted to the vacuum and inert-gas fusion methods, a resume of other suggested methods for analyzing titanium for oxygen also is given. INTRODUCTION The Federal Bureau of Nines has conducted research on titanium metal since 1938. This research included development of the Kroll process for the production of titanium (2)4, various sodium reduction processes for making titanium metal and lower valent titanium chloride-sodium chloride mixtures (17), and a fused salt electrolytic process for Me production of high-purity titanium metal and the recovery of titanium by electrorefining from off-grade materials (20).

Jan 1, 1961

By M. R. Geer

Efforts to evaluate washery performance are nearly as old as the art of coal cleaning, and in former years there was no uniformity in either the methods used or the basic terminology employed. This situation, and the con- fusion it bred, prevailed until about the time of the First International Coal Preparation Conference in 1950, Largely because of the interest of the French coal research organization Cerchar, the subject of evaluating performance was given prime importance at this conference. As a result, there is now a much greater degree of uniformity in terminology and methods of expressing cleaning results. The International Standards Organization currently is working toward international standards of terminology and methods that should improve the situation even more. The various criteria that are used to evaluate the performance of coal- cleaning equipment fall into three categories, depending upon the extent to which they are dependent on the density composition of the raw coal; some are directly dependent, others are only indirectly dependent, and still others are substantially indenpendent.

Jan 1, 1962

By K. T. Lee, M. U. Ozbay, M. D. G. Salamon

Design of yielding chain pillars in deep coal longwall mines is not as well established due mainly to the lack of knowledge in the behavior of coal pillars in the post-peak regime. This study shows that two of the existing strain-softening models have the potential to provide an improved understanding of yielding and, therefore, could form a rational basis for yielding coal pillar design. Analytic and numerical modelings of a row of chain pillars in a two-entry development at a depth of nearly 700 m suggests that yielding pillars are feasible, but the design is very sensitive to the coal’s post-peak behavior.

Jan 1, 2001

By L. Ozdemir, M. Cigla

This paper presents and discusses some of the computer models developed and currently used at the Earth Mechanics Institute (EMI) of the Colorado School of Mines (CSM). These include the performance models for full and partial face machines. Examples of input and output of these models will be illustrated for typical mining operations by using machines such as Tunnel Boring Machines (TBM), Continuous Miners (CM), Marietta borer miners and longwall drum shearers. The general approach to modeling and the available models are discussed and some examples of these models are presented. The comparison between the estimated and achieved performance, as well as the degree of improvement in the performance due to balancing and modification in cutterhead design are also discussed.

Jan 1, 2000

By J. J. Shields

This study by the Federal Bureau of Mines concerns different methods of face haulage used with various types of continuous-mining machines, mobile-loading machines, and track-mounted equipment under varying roof and bottom conditions and in coalbeds of varying thicknesses. This report is the ninth in a series on mechanical mining in bituminous coal mines. Reference to the reports previously published is made in appendix III, p. 106. Use of modern mining equipment in bituminous coal mines has resulted in increased productivity at the face. This especially is true where continuous-mining machines are used, and the supervision is good. Previous methods and equipment for moving coal from the face became inadequate and had to be improved to restore balance to the mining systems. Sometimes new equipment was needed to improve the face haulage, and in some instances, a new combination of existing equipment was used. Detailed studies of face haulage methods were made at 13 mines in Pennsylvania, West Virginia, Ohio, and Illinois to compare their effectiveness and to describe fully the conditions under which each method was used.

Jan 1, 1960

By L. B. Berger

The Haldane gas-analysis apparatus used by the Bureau of Mines is patterned after the device developed by Haldane 4/ and differs from it only in structural modifications that have been added to facilitate operation and simplify construction. The apparatus was developed to permit determination of carbon dioxide, combustible gases, and oxygen with a degree of accuracy not attainable with apparatus of the types ordinarily used for the analysis of fuel gases, flue gases, and similar mixtures. The Haldane apparatus is used by the Bureau of Mines chiefly in the analysis of air samples collected in coal and metal mines and other underground workings and is applied also in the analysis of many other types of gas mixtures when accurate determination of certain constituents is desired.

Jan 1, 1938

The small-scale surface mining operation in northern regions is typically located in a remote, ungaged basin. With the recent increase in the economic potential of mining, the number of small operations is increasing. The year-to-year variability in precipitation in this region under study is of great concern to mine operators. Some years may yield only 5 to 6 inches of precipitation, while others may yield in excess of 15 inches. Such variability makes placer mining operations difficult to plan, since low water years may result in too little run-off for gravel washing and high water years may result in flooding of mining developments. There are no official streamfloaw records in many watersheds in the northern region containing placer mining claims. However, information from other streams permits calculation of an estimated discharge for a watershed under consideration using average flows per square mile of drainage. It is to be emphasized that these are average or expected figures in reality, one water year may be significantly wetter or drier than another. This high variability of annual precipitation is significant in relation to placer operations because of the large quantities of water required for this type of mining. Some operations can not operate in low water years. In the larger watersheds, operations may continue in low water years but at a slower pace because of longer water collecting times. The high variability of available run-off rakes placer mining in many parts of Alaska difficult to plan on a long range because of the unpredictability of water supplies.

Jan 1, 1985

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the utilization of municipal solid waste. One of the primary objectives is the recycling of the magnetic fraction of municipal solid waste (raw refuse). This is consistent with one of the Bureau's goals, which is to minimize the requirements for mineral commodities by maximizing metals recovery from secondary domestic resources, In this investigation, cupola trials were made using combinations of refuse scrap with shredded automobile scrap under basic and acid slag practices. Furnace operating information and the behavior of alloying and tramp elements was obtained. The research showed that it is possible to utilize up to 60 percent refuse scrap in the cupola under basic practice and 30 percent under acid practice, Aluminum in refuse scrap, present in bimetallic cans, increased the recoveries of silicon and manganese charged to the cupola. Increased use of refuse scrap provided iron of lower sulfur. The alumina resulting from oxidation increased the slag volume. The aluminum and tin contents of the iron increased with increasing levels of refuse scrap in the charge. Lead was not a problem with respect to contamination of the iron. In basic practice, operation of the cupola was satisfactory since all slags were adequately fluid. In acid practice, operation became troublesome above the 45-percent level. Under both practices, the cupola iron melting rate decreased. Particulates in scrubber water and stack condensate samples contained lead, zinc, and tin, and the dust load increased. The tensile and transverse strengths of the iron produced under both practices are reported.

Jan 1, 1980

By Jan E. Nesset, James A. Finch, Wei Zhang

"Bubbles are unquestionably the heart of the flotation process. Their size and combined surface area are largely what drive the recovery process. This suggests that plant engineers should be aware of where their plants are operating with respect to what is achievable for these key parameters. The paper presents a model of how the key operating variables of frother type and concentration, gas rate, altitude (above sea level) and viscosity affect the Sauter mean bubble size (D32) and bubble surface area flux (Sb). The results are compared to a set of plant measurements that demonstrate the benchmarking capability of the approach. A case study is used to link hydrodynamic change to improved metallurgical performance.INTRODUCTION At the beginning of the 20th Century the early practitioners of flotation were aware of the importance of understanding bubble behaviour (Rickard, 1916) but measurement of individual bubble and gas behaviour in the industrial environment was not possible due to a lack of adequate sensors. This situation was not rectified until three quarters of a century later with the advent of industrially-robust sensors developed, notably, at the University of Queensland’s Julius Kruttschnitt Mineral Research Centre (JKMRC) (Schwarz & Alexander, 2006) and McGill University (Gomez & Finch, 2002). What emerged was not the chaotic environment perhaps expected, but defined relationships between gas rate, gas holdup, bubble size and the total surface area of bubbles. These relationships could be defined by mathematical expressions and predicted from an understanding of the key process variables (Gorain, Franzidis & Manlapig, 1997; 1999) (Hernandez-Aguilar, Gomez & Finch, 2002) (Gomez, Cortes-Lopez & Finch, 2003) (Nesset, Gomez & Finch, 2007). The early JKMRC work focused on a large pilot cell (3 m3) installed in plant environments, while the McGill work was initiated on flotation columns (Finch & Dobby, 1990) (Xu, Finch & Uribe-Sales, 1991) and later adapted to industrial mechanical cells (Cooper, Scott, Dahlke, Finch & Gomez, 2004) (Dahlke, Gomez & Finch, 2005) (Nesset, Gomez, Finch, Hernandez-Aguilar & Difeo, 2005). Yianatos of Santa Maria University (Chile), a graduate of the McGill research team, carried the work to industrial settings in South and Central America (Yianatos, Bergh, Condori & Aguilera, 2001). The methods of gas dispersion measurement are now well accepted and most major research centres and flotation cell manufacturers have adopted the technology (Pyecha, Sim, Lacouture, Hope & Stradling, 2006) (Yañez et al., 2009) (Collins, Schwarz & Alexander, 2009)."

Jan 1, 2012

By D. E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2.0 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH's Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis, and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items which require the constant attention of miners operating in these conditions. Disclaimer: Mention of any company or product does not constitute endorsement by the National Institute for Occupational Safety and Health.

Jan 1, 2009

By D James

Fletcher Challenge Limited through its subsidiary Grampian Mining Co Limited has carried out an ore evaluation of one of New Zealand's largest known deposits of ilmenite located at Barrytown on the West Coast of the South Island, New Zealand. The ilmenite is located in a beach sand environment which has previously been mined for gold. Two analytical techniques were developed to quantify the resource. Considerable difficulty was experienced in this phase of the evaluation due to the presence of major inclusions within the ilmenite grains. Wet and dry concentration circuits, utilising spiral, wet magnet, high tension and plate electrostatic separators have been designed to produce ilmenite from the ore. Studies to utilise the titanium content of the Barrytown ilmenite have been made. Recent work has been directed towards a titanium dioxide pigment process.

Jan 1, 1986

By Gregory R. Gorrell

The legal issues surrounding the regulation of subsidence are among the major concerns facing the underground mining industry today. Whether subsidence occurs almost immediately as a result of longwall mining or without warning as a result of room and pillar mining conducted years ago, the resulting disputes are highly controversial and typical of the disputes involving the competing interests of surface and mineral estate owners. Until recently, the law governing these disputes was firmly established under the common law. The passage of the Surface Mining Control and Reclamation Act 1, the utilization of new mining technologies, and the general heightened environmental awareness of our times, however, have interjected new issues into this area of the law. State and Federal court decisions and administrative agency interpretations have helped clarify some of the issues. However, as evidenced by the many recent lawsuits between operators, surface owners, and regulatory agencies, many uncertainties still exist.

Jan 1, 1986

By I. Alp

Application of magnetic separation was investigated for the enrichment of colemanite ores by removing the magnetic gangue fraction. The detailed XRD analysis of the ore has indicated that the gangue fraction is composed predominantly of the iron-bearing silicates such as smectite and, to a lesser extent, illite. Magnetic susceptibility measurements of the colemanite and gangue samples have proved that colemanite is diamagnetic in character whereas gangue fraction is weakly paramagnetic to allow the removal of this fraction by magnetic separation. Magnetic separation of the crushed and sized ore samples (-5 mm +75 µm) was performed using a high intensity permanent magnetic separator. Under the test conditions a colemanite concentrate (41.29 wt.% B2O3) was found to be produced from the crushed ore (30.76 wt.% B2O3) at a recovery of 96.76%. These findings suggest that magnetic separation has great potential as an alternative process for the production of a concentrate of commercially sufficient grade.

Jan 1, 2009

In preparing a paper such as this it was thought that the Newstan Colliery Company Ltd., being comparatively new, would need some introduction to mining people in general.The Newstan Company was formed by the Joint Coal Board in December, 1948 during a period of acute coal shortages. The Company took over the holdings of what were known as the Olstan and Northumberland Collieries, situated at Fassifern, alongside Lake Macquarie and adjacent to the Great Northern Railway, within easy rail access of Sydney and Newcastle, as shown on the locality plan (Fig. 1).The Company was developed in order to produce steaming coal for the power house trade and has continued its activities in the steaming coal trade since its inception. The Olstan and Northumberland collieries were together producing some 300 tons per day when the Company was formed, and it was from this foundation that the colliery was built. The planned development of the Company has been along the lines of producing coal by modern, highly mechanised methods, together with the preparation of theproduct for the consumer, to the highest degree possible consistent with up to date methods.In the comparatively short time of 5t years the mine has developed from a small hand-won coal unit to a high capacity modern mine, one of Australia's largest producers, with an output capacity as high as 3,000 tons per shift.

Jan 1, 1954

By A Bagchi, Nabiullah, Jagdieh

"A number of coal mines in India are affected by fire. Most of coking coal reserves in the country are located in Jharia coalfield where more than 18 sq. km is in the grip of fire. Generally such fires are confined in areas near to our crops. About 37 million tonnes of coking coal are lost in recent yearsdue to fire and another 48 million tonnes are blocked in fire areas. Preventive measures adopted to control fires were only partially successful and the cost of such measures was exorbitant I Temperature of blast holes in fire area varies between 60 and 300° C or even more. Even after thorough quenching of holes with water, it become difficult to bring down the temperature below SO"" C. For blasting hot holes primary need is to select safe and suitable commercial explosives and detonating fuse and to measure hot hole temperatures. VWiOUs types of commercially available explosives including Nitro Glycerine bare, slurries, site mixed slurries (SMS), emulsion5 ,detonating fuses and detonators were tested to determine their thermal behaviour at elevated temperatures under field simulated conditions in the Copyright © 2000 International Society of Explosives Engineers 1993g - Studies on Safe Blasting Technique in Fire Area of Coal Mines laboratory and in hot blast holes in field . More than 50 round of blast were conducted in fire areas. NG base compositions and detonators were found unsafe at temperature above SO0 C andtherefore, they are not permitted to be used in hot holes. Slurries and emulsion are stable upto 1200 c. For blasting at temperature exceeding SO0 C a heat resistant gel/ solution was developed by the authors and is being used in number of fire areas."

Jan 1, 1993

By S. Addie

In the early 1990’s the British Columbia (Canada) mineral industry frequently discussed the need to participate in, and compromise with, public environmental interests in order to ascertain long-term stability. However, as the decade progressed the mineral industry withdrew from almost all meaningful public participation. As government protected areas policy in the past year has illuminated, there is a continued need for long-term land access stability. This paper historically analyses the public engagement policies of the British Columbian mineral industry while it participated in long-term consensus-based multi-stakeholder land-use planning processes. From this analysis the paper recommends that the mineral industry reengage the public and institute a new working relationship with environmental advocacy groups so as to ensure British Columbia becomes the most sustainable mineral producing jurisdiction in the world.

Jan 1, 2011

By Mandeep Singh

The smelting of lead ores has been carried out in southeast Missouri for centuries, and modern smelting practices have generated a variety of waste products. Lead blast furnace slag is one such product, which typically contains 10% zinc, 25% iron and 2% lead. This slag has often been stockpiled on the producing smelter site and accumulations have now reached several million tonnes. It is possible that in the near future these slags will be classified by the federal Environmental Protection Agency as hazardous, and therefore there is considerable interest in possible treatment processes to render the slags non-hazardous by removing the offending metallic elements. To ensure that the overall slag processing costs are kept to a minimum, it is imperative that lead and zinc be recovered in a form suitable for sale or further processing. There are two generic routes for processing blast furnace slags and they involve hydro-metallurgical or pyrometallurgical techniques. With hydrometallurgy, the slags would be leached directly and the metal values recovered from purified leach solution(s) by electrowinning. One problem with processes of this type is that the zinc and lead grades of the slags are low and the iron content is high, and thus the economics of metal production are often not favorable. For pyrometallurgical processing (1), it has been shown that the slags can be fumed to produce an oxide dust containing all the lead and zinc, and representing only a fraction of the weight of the initial slag. The oxide dust may then be processed hydrometallurgical to recover zinc and lead.

Jan 1, 1992

Open pit mine plans define the complex strategy of displacement of ore and waste over the mine life. Various mixed integer linear programming (MILP) formulations have been used for production scheduling of open pit mines. The main problem with these models is the inability to solve real size mining problems. We present a mixed integer linear programming formulation for the open pit long-term production scheduling problem. To reduce the number of binary integer variables in the formulation, we aggregate blocks into larger units referred to as mining-cuts. We present a semi-supervised clustering algorithm which aggregates smaller blocks based on rock types and grade ranges into mining-cuts without introducing an error in the grade estimated values. The cluster-based aggregation algorithm is fully integrated into an MILP mine production scheduling prototype software. We have implemented, verified, and validated our models. The efficiency of the new platform is evaluated through iron ore mine case study.

Dec 6, 2010

By M. Tangstad, B. Monsen, H. Midtgaard, R. Ishak, M. Syvertsen, I. Solheim

Charcoal is an interesting reducing agent because it is produced from growing wood which is renewable and does not contribute to global warming, provided that there is a balance between the felling of timber and growth of trees. In the biocarbon project the possibilities for using charcoal is investigated as well as other biological based and renewable reductants for ferroalloy production. The background for the project is that the Norwegian ferroalloy producers wish to contribute to reduction of CO2- emissions. This paper focuses on the use of charcoal instead of coke for the production of manganese alloys, and the consequences of doing so. Results from practical SiMn smelting experiments on a pilot scale have previously been reported, where only 12-14 % Si in the metal was obtained when charcoal was used. Recently we have attained satisfactory 18 %Si also for charcoal, but good results are indeed dependant on good furnace performance. There is no tradition for using charcoal for manganese production in Norway. A change from using mainly coke to the use of some charcoal will demand new routines for furnace operation, raw material and off-gas handling. Hence, characteristic properties of charcoal, which may cause change of furnace operation, have been measured and are compared to coke. The following results are presented: ?Thermal abrasion strength together with CO2- reactivity; important parameters for the performance of the upper part of the furnace. ?Coke-bed resistance; it will increase with the use of charcoal (a review of new results). ?Slag reactivity; a relevant method for testing slag reactivity of industrial reductants is of interest. The suggested method can serve for comparing slag reactivities towards graphite.

Jan 1, 2007

[This Bureau of Mines report presents results of a survey of underground mining equipment and of two demonstration programs showing the feasibility If quieting; a load-haul-dump (LHD) machine and a personnel vehicle. Typical noise levels are presented for the major machine types used in underground mines, along with estimates of the noise overexposure of miners who operate or work near these machines. General principles of noise control are explained, and the application of these principles is illustrated in the description of modifications made to the LHD machine and the personnel vehicle. The noise control package installed On the persona of vehicle lowered its noise level by 14 dBA after 4 months of operation, and inspection of the LHD machine after 2 1/2 years of operation with the modifications showed its noise level 7 dBA lower than that of the unmodified machine. Noise dosimeter measurements indicated that both machines were in compliance with Federal noise regulations for a typical shift.]

Jan 1, 1980