Search Documents

By K. Norrena

Grade control in open pit mining requires the specification of dig limits that account for mineral grades, economic costs, and selectivity of mining equipment. Visual identification of ore rock types is ideal, but this is not always possible in lower grade disseminated deposits where ore/waste contacts are not visually discernible. In this case, conventional grade control practice consists of a two-step procedure (1) create a map of mineral grades at some selective mining unit scale, and (2) determine practical ore-waste boundaries or dig limits on the basis of the gridded block grades or assay information. This procedure is laborious, depends on a subjective assessment of where the boundary should be, and may be economically sub-optimal. We pose the determination of dig limits as an optimization problem and solve that problem with the technique of simulated annealing. Simulated annealing has the unique advantage of being able to combine multiple non-linear constraints into a single objective function. We use maximum profitability and the ability of the equipment to mine the proposed dig limits as constraints in the determination of optimal dig limits. We require a map of expected profit for eah block. Geostatistical techniques are recommended, for mapping expected profit but not necessary. Geostatistics will provide a quantification of the uncertainty in the grades within rock types using all available blasthole samples and exploration drilling. Some variant of L-optimal estimation or kriging can be used to determine the block-by-block classification that is economically optimum. We also need the expected profit for each block. It is unrealistic to assume free selection, that is, each block cannot be extracted independently of its neighbors. The optimal balance of ''accepting dilution'' and ''wasting ore'' is achieved to maximize profit subject to equipment constraints.

Jan 1, 2001

By Austin E. Dwight

IT has been shown by Oelsen and Wever' that the effect of a solute element on the allotropic transformation in iron is dependent upon the quantity

Jan 1, 1957

By Werner Burger

The Hallandsås project with a long history, first started in 1991, is well known in the tunneling community. In the past it has been stopped twice for technical and environmental reasons. The third attempt started in 2004 using a dual mode rock TBM. The heterogeneous highly fractured and abrasive rock mass as well as large areas of water bearing zones present most difficult subsurface conditions. The tunneling concept is based on the use of watertight segmental lining and a TBM able to operate in open mode, possibilities for extensive pre excavation grouting and high pressure closed mode operation up to 13 bar to cover exceptional conditions.

By Y. D. Lee, J. H. Park, D. S. Kim, H. S. Song

The viscosities and the infrared spectra of the CaO-SiO2-MgO-CaF2(or Al2O3) slags were measured to enhance our understanding of the interrelationship among the thermophysical property, microscopic structure, and chemical thermodynamics of molten slags. The structural role of CaF2and Al2O3in the calcium silicate melts can be explained by a change of the degree of polymerization (DOP). The effect of CaF2on the viscous flow of molten slags is based on a decrease in the DOP by F-as well as by O2-ions and this was confirmed by the infrared (IR)spectra of the quenched slags. The effect of Al2O3on viscosity increase can be understood from an increase in the DOP by the incorporation of the [AlO4]-tetrahedra into the [SiO4]-tetrahedral units and this was also confirmed by the IR spectra. An amphoteric behaviour of Al2O3in the aluminosilicate melts could be correlated to the effect of ionic species of alumina, that is [AlO4]-tetrahedra and [AlO6]-octahedra, on the stability of silicate polyanions by taking the activity coefficients of slag components into account. Keywords: viscosity; infrared spectra; degree of polymerization; amphoteric behaviour; stability; activity coefficient

Jan 1, 2004

The process of hydraulic transport through pipelines, worldwide well known for the transport of fine-grain solids is also being used to a greater extent in mining for the handling of primarily coarse-grain solid û water mixtures for the removal of, for instance û coal and waste mixtures after coal winning using hydraulic monitors, tailings for backfilling underground and washer tailings and flotation waste to the dump. A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining Research Company) in Essen-Kray, GFR, to further improve this technology. The unit was planned and built by Krupp Industrie- und Stahlbau of Duisburg in cooperation with Bergbauforschung GmbH. The paper deals in detail with the demands made on this test unit and the technical results obtained on it and with the planned experimental research work.

Jan 1, 1980

By Hani Henein

Recent innovations in atomization of molten metals have occurred in the area of single fluid atomization. Impulse Atomization (IA), one of the single fluid techniques, provides unique capabilities to study different regimes of atomization in a controlled environment. By changing processing variables, a mono-dispersed distribution of droplets above one millimeter in diameter can be produced. This is accomplished through proper characterization of the forces influencing the process and in particular the flow of melt through the orifice. This paper will discuss the approach and illustrate results with molten aluminum and cobalt.

Jan 1, 2006

By Gilberto Nunez, Ron Eastman, Hector Parra

The prediction of blasting outputs has proven to be a sound engineering tool to provide a guideline for design improvement. It has also been demonstrated to be extremely useful in critical situations when production can be compromised and there is no chance for error.

Jan 1, 2015

This study was conducted to determine the effects of a machine-mounted scrubber and water sprays on face methane levels. Testing was conducted in the NIOSH ventilation test gallery which was designed to simulate a full-scale mine entry. In the test entry, a model mining machine, equipped with water sprays and a simulated dust scrubber, was located at the face of a 20-ft box cut. Blowing ventilation was provided using a curtain with a 40-ft setback distance. Methane released from a pipe manifold located inby the mining machine was monitored at six locations that were 1 ft outby the pipe manifold. Tests were first conducted to evaluate the effects of using sprays and scrubber separately on face methane levels. Additional tests were conducted to determine how a scrubber used with various water spray systems would affect face methane levels. The use of either sprays or scrubber reduced face methane levels significantly. The combined use of sprays with the scrubber further reduced face methane levels a small amount. Primarily the sprays affected methane levels by changing airflow distribution close to the face.

Jan 1, 2001

By T. Lindstad, J. Kaczorowski

The Boudouard reactivity of single cokes produced from selected bituminous coals and commercial cokes has been investigated in a thermo gravimetric furnace. The effect of potassium as a catalyst for this reaction was studied, as it is known to accumulate in ferromanganese furnaces. A gaseous impregnation technique using K2CO3 as the potassium source was applied to impregnate the coke samples. The reactivity experiments were designed to simulate conditions occurring in an industrial furnace, as used for production of Mn-alloys. The coke particle size varied from 3.35 to 6.63 mm, while the temperature was maintained between 800- 1100oC with a gas composition from 50 to 75% CO2 in a CO/CO2 mixture. To determine the catalytic effect of potassium, the concentration varied from a fraction of a percent up to 15%wt. The results show that single chars vary significantly in reactivity, depending on the properties of the parent coal, while commercial cokes exhibit similar reaction rates. Temperature and partial pressure of CO2 have the strongest influence on the reactivity, while the influence of gas flow rate and coke particle size were found to be negligible. The catalytic studies revealed that the relative reactivity of non-impregnated samples are preserved after the impregnation, so the least reactive coke is still the least reactive after the impregnation for the whole range of potassium loads. Also, it has been confirmed that the Boudouard reactivity reaches a plateau at potassium concentration of 4%wt.

Jan 1, 2007

A computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. The system operates, interactively from a Tektronix 4014 graphics terminal which handles all input/output functions. The software is installed on a Cyber 74 computer that communicates with the terminal via telephone line.

Jan 1, 1978

By S. J. Benson

The Harts Range deposit, owned by Olympia Resources is located some 130 kms northeast of Alice Springs, in central Australia (part of Australia’s Northern Territory). The core economic minerals here are industrial grade garnet and alumino magnesio hornblende (AMH). The resource contains an estimated 2.3 million tonnes of recoverable garnet and 6.2 million tonnes of recoverable AMH, making Harts Range one of the most significant abrasive medium deposits in the world. Part of the general marketing axiom of Olympia Resources is to make high quality products from the garnet and also a special series of blended garnet/AMH products to match the needs for other sectors of industry. The deposit mineralization is of alluvial origin and thus, requires no significant liberation regimes. Over 50% of the head feed is in the form of SiO2/quartz and as much as 17% is –63micron clay slimes and mica. Original pilot scale testwork for flowsheet development centred around fairly conventional wet gravity systems, with spiral concentrators being the pre-eminent separating device. To a point, this type of flowsheet was going to achieve some of the aims albeit fairly predictably. The one area that this circuit would be very limited though is in the recovery of the very coarsest of the medium SG minerals. This was going to be a very important and longer-term costly flaw. Amongst the highest demand, greatest value of products to be produced will be the range of garnet & AMH in the +600 microns sector. A flowsheet dominated by spirals would be fated to forfeit a significant proportion of these coarse minerals to tails. At the Outokumpu Technology P/L test facilities in Perth, testwork was conducted using a pilot scale Floatex® Density Separator, the LPF-230 model. Using a twin stage approach, whereby a primary Floatex® underflow reports directly to a secondary Floatex®, recovery of the economically important +600 micron garnet was increased from 65% in the spirals-only flowsheet to 95% using the Floatex® based flowsheet. Finally, the other significant aspect of this approach is in substantial simplification of the circuit required and a huge reduction in plant footprint. Also, the nature of using hindered settling provides substantial opportunities for process control and automation.

Jan 1, 2005

Objective To reduce dust generated from soiled floors within enclosed operator cabs. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. For cabs to be effective in controlling airborne respirable dust, they must have an efficient air filtration system, while providing a positive pressurization of the cab interior. Ideally, the recirculated and exterior makeup air filtration should provide at least 99% capture efficiency for dust particles as small as 0.3-µmaerodynamic diameters. Many of these enclosed cabs use heating units mounted or directed along the floor (see figure 1), which can cause dust entrainment problems. Prior studies by the National Institute for Occupational Safety and Health (NIOSH) of enclosed cabs have shown that these floor heaters can generate notable amounts of dust within the cab enclosure (see Technology News 486). Multiple-shift dust levels measured inside a drill cab increased on average from0.04 mg/m3 during the summer months to 0.68 mg/m3 during the winter months. Additional dust level measurements, made with optical particle counters during a nondrilling time period, verified that dust levels inside the cab increased from 0.03 to 0.26 mg/m3when the floor heater/fan was turned on. Dust levels within the cab also became greater than the ambient air dust levels outside of the cab when the floor heater was turned on during the nondrilling time period. This shows that the floor heater was a notable dust source problem. Cab floors are commonly soiled from operators tracking dirt inside the cab upon entering from the mine or construction site. Interior cab dust levels can be increased by (1) airflow disturbance of the soiled floor or (2) operator disturbance of the soiled floor. Approach During prior NIOSH surveys of surface coal mine drills, several drills with very low cab dust levels (#0.1 mg/m3) were observed to have floor sweeping compound spread out over the cab floor during the working shift. This initial observation led to a more controlled A-B study of the effect of the sweeping compound on the interior cab dust levels. This study involved dust sampling with and without sweeping compound inside the cabs of a bulldozer and two drills. Sweeping compounds commonly use sawdust or cellulose as the main bulk material, with oil or wax added for dust adhesion purposes. Sand is sometimes added to increase bulk density. Sweeping compounds with sand are commonly used to sweep up concrete floors. Those without sand (usually referred to as "gritless") are used to sweep up smooth finished floors. Most of the oils and waxes used for the adhesive ingredient are petroleum-base and can have an irritating odor. People sensitized to petroleum distillates could have allergic reactions to these sweeping compounds. A few companies offer non petroleum-base sweeping compounds, using either a natural oil or chemical additive for dust adhesion. During this study, it was decided that only the gritless sweeping compound (without sand) would be used, eliminating the addition of another potential silica source inside the cab. Since the sweeping compound would be applied on the enclosed cab floor for the duration of the shift, it was decided to use a canola oil-base sweeping compound to eliminate irritating odor from the petroleum-base sweeping compounds. The natural canola oil-base sweeping compound had a slight woody scent. The three pieces of equipment used in this study had notably different cab layouts. The bulldozer had a small cab with vents discharging air-conditioned or heated air from adjustable louvers at operator waist level and floor level. The bulldozer also had a cloth fabric seat and a carpeted floor. Drill A had a large cab with the heat directed from adjustable louvers at operator knee level and the air-conditioned air directed from cabin ceiling louvers. This drill had a vinyl fabric seat and a steel plate floor. Drill B had a small cabin with the heat directed across the floor (see figure 1) and the air-conditioned air directed down from the ceiling. It had a vinyl fabric seat and a worn rubber mat on a steel floor.

May 1, 2001

By Michael Jatczak

The San Vicente Tunnel Project is an 11-mile water tunnel constructed for the San Diego County Water Authority. One of the many challenges of the project included tunneling a 22,000-foot single-heading tunnel on the western half of the job in varying geology using a 3.66m (12ft) diameter open shield excavator or ?digger shield.? This paper will discuss the design considerations for the temporary liner, the tunneling, and ancillary equipment. It will also highlight the challenges faced while mining this geology, explain the methods implemented to drive this section of tunnel, and discuss the experiences while performing mechanized tunneling in an extensive and varied San Diego geology.

By Mostafa Benzaazoua, Bruno Bussière, Philippe Poirier, Denis Bois

"Environmental desulphurisation is an attractive alternative for the management of acid generating tailings. Non selective froth flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works (McLaughlin and Stuparyk, 1994; Bussière et al., 1995; 1998; Benzaazoua et al., 2000a,b; 2002). This process can reduce the volume of problematic tailings to manage, by making a sulphide fraction concentrate. The desulphurized tailings can then be used as a moisture retention layer in a cover with capillary barrier effects to prevent acid mine drainage.In this paper, the authors present the results from different laboratory and pilot scale flotation tests which confirm that low sulphide, non-acid generating tailings can be produced by froth flotation. It is also demonstrated that the sulphide concentrates obtained from desulphurisation, when mixed with binders gave good long term results in terms of mechanical behaviour, thus demonstrating that the sulphide fraction can be used for paste backfill material. From previous work (Bussière et al. 1998, 1999) on the evaluation of the operating and capital costs of the desulphurisation process for different ore types, the use of desulphurized tailings to create a dry cover was then studied for several scenarios. The desulphurisation process was compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation and the advantages and disadvantages of desulphurisation are presented as well as the costs of this method of AD prevention.INTRODUCTIONThe principal environmental problem of the mining industry today is the generation of acidic drainage (AD) resulting from the natural oxidation of the sulphides in mine tailings. This phenomenon involves the generation of acidity which increase the amounts of toxic metals in the waste water released into the environment by a mine. The environmental impact of the AD has been described in detail in previous work (e.g. Down et Stocks, 1977; Ritcey, 1989; Gray, 1997; Ripley et al., 1996; Aubertin et al., 2002)."

Jan 1, 2004

By L. Alan Weakly

Global warming is a political reality in the United States today. The actual impact of the continued utilization of fossil fuels is not known and is open to debate. However, the growing concern about the continued use of these fuels is problematic. There are technologies available to us today that would permit America to meet its future energy demand and not contribute to global warming. The inconvenient reality is that fossil fuels cannot completely be replaced with energy conservation and the use of wind, solar, hydroelectric, geothermal and nuclear energy. The connection between the greenhouse effect and global climate change was first identified by physicist John Tyndall in the 1860s. To prove the greenhouse hypothesis, Roger Revelle and his research team started measuring carbon dioxide concentrations in the earth?s atmosphere in the early 1960s (Becker, 2007). With the rising concern about global warming, scientists throughout the world have been obtaining surface and air temperature data. Scientists have also been comparing CO2 concentrations found in glaciers throughout the world with theorized annual temperatures. Data for both dates back 1,000 years. Armed with this data, many nations of the world and the United Nations Intergovernmental Panel on Climate Change (IPCC) have concluded that climate change is a reality. The IPCC also concluded that this climate change is the result of mankind?s consumption of fossil fuels and that catastrophic consequences will occur on a

Jan 1, 2008

By Wesley Schmutzler

The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.

By Robert Martin, Brian W. Stump, David P. Anderson, W Scott Philips

Since 1994, various mines in the US have cooperated with research scientists at the Los Alamos and Lawrence Livermore National Laboratories to address issues related to verification of the Comprehensive Test Ban Treaty (CTBT). The .CTBT requires that no country may conduct any nuclear explosion in the future. While the CTBT is a significant step toward reducing the global nuclear danger, verifying compliance with the treaty requires that the monitoring system be able to detect, locate and identify much larger numbers of smaller amplitude seismic events than had been required previously. Large mining blasts conducted world-wide will be of sufficient amplitude to trigger the monitoring system at the lower threshold. It is therefore imperative that research into the range various blasting practices employed, the relationship of yield to seismic magnitude, and identification of anomalous blasting results be performed. This paper will describe a suite of experiments funded by the Department of Energy and conducted by the Los Alamos and Lawrence Livermore National Laboratories in cooperation with the US mining industry. Observations of cast blasting, underground long wall generated coal bumps, stoping, and explosively induced collapse of room and pillar panels will be presented. Results of these dual use experiments which are of interest to the mining community will be discussed. These include 1) variation of amplitude of seismic energy at various azimuths from cast blasts, 2) identification of the extent of back failure following explosive removal of pillars, and 3) the use of single fired shots for calibration of the monitoring system. The wealth of information and discovery described in this paper is a direct result of mutual cooperation between the US Government and the US Mining Industry.

Jan 1, 1997

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By Lewis Dr. Wade

It is really an honor and pleasure to be here at the 231d International Conference on Ground Control in Mining. My name is Lew Wade. Until recently I served as the Associate Director of Mining for NIOSH. That's a position that I recently moved out of and that position is now filled by Dr. Jeffery Kohler. I now serve as the Sr. Science Advisor to the NIOSH Director. The topic of my talk today will be coal mine ground control, a look back at the last 30 years, and then a brief look forward. I will start by talking about coal mine ground control statistics and with just a brief look, those statistics clearly show that you people are making a difference and there have been tremendous improvements. I'll then look at reasons for those improvements and those will include people working together (this conference being a prefect example of that), as well as technology development. In the area of technology development, I will give you my top-ten list of technology developments in the area of coal mine ground control. Then I'll end with a look towards the future and point to some possible future developments. Then, I will be so bold as to issue some challenges to the participants of this conference. Again, if you take the broad look back at underground coal mine roof falls and ground fatalities, you see this tremendous improvement that we have all come to appreciate. We have all been a part of improving the safety conditions for our underground miners and the number of fatalities is orders of magnitude less than what it was at the turn of the previous century. We have every reason to be pleased and proud of what we have been able to accomplish. Now, the question is why. What are the reasons for those improvements? Just look around this room. You see evidence of what I think are one of the principle reasons: miners, mine operators, government workers and researchers, equipment suppliers, people in research and academia working together. Coming together and sharing at a Conference like this over the last 23 years.

Jan 1, 2005

By R. R. Sayers

The increasing use of hydrogen fluoride (annual consumption now exceeds 500,000 pounds (1)4/) directly and its occurrence as a byproduct of the utilization of fluorine compounds in the mineral industries, especially in metallurgical processes and in the refining of petroleum products, has aroused interest in its toxicity, and a brief review of the literature, with special reference to the hazard of poisoning in the mineral industries, seems to be opportune. Recently, residents in the vicinity of aluminum plants have been complaining of injury to livestock and vegetation as well as to their own health from the gases discharged into the air during operation of the plants, hydrofluoric acid gas apparently being the offender. The comparatively recent utilization of hydrofluoric acid in the alkylation process for the production of high-octane gasoline has raised the question of the hazard of poisoning in the petroleum Industry. In addition, the use of fluorine-containing refrigerants has extended the potential al exposure outside of industry (2).

Jan 1, 1945