Search Documents

By C. R. Boyd

WITHOUT attempting to do more than give a preliminary or skeleton report upon the geology and minerals of Southwestern Virginia at this time, I am led to hope that the great commercial importance of the sixty miles of cross-section here crudely treated of

Jan 1, 1877

By M. Murakami, Y. Murakami, O. Kawano

The formation and growth of Guinier-Preston zones in Al-Zn alloys containing 4.4, 6.8, 9.7, and 12.4 at. pct zn have been studied by the X-ray small-angle scattering method. Particular attention was paid to the effects of small amounts of third elements silver, silicon, and magnesium on the formation and growth of G.P. zones. It was noticed that an appreciable number of G.P. zones were formed during the course of rapid cooling and that the size, volume fraction, and number of these G.P. zones were influenced by the existence of the third elements. During subsequent aging it was also found that the addition of both silver and silicon lowered the temperature for the growth of G.P. zones, whereas the addition of magnesium raised it. These results were explained in terms of the mutual interactions among zinc atoms, vacancies, and the third elements. A number of studies on the formation and growth of Guinier-Preston zones in Al-Zn alloys have been reported.1-4 Panseri and Federighii have found that the initial stages of zone growth take place at temperatures as low as around -100°C. For investigation of the mechanism of the initial stages of zone growth, growth studies must be carried out at low temperatures. In order to investigate the possibility of the formation of G.P. zones by the nucleation mechanism or the spinodal decomposition during quenching which was reported by Rundman and Hilliard,5 the examination of the as-quenched structure must be performed. In this paper the investigation of the early stages of the formation and growth were determined by means of the X-ray small-angle scattering method. With this technique, change of X-ray scattering intensities was measured while quenched specimens were heated slowly from liquid-nitrogen temperature to room temperature. At as-quenched state and after heated to room temperature, investigation of zone size, volume fraction, and zone number per unit volume was carried out. Measurements on these specimens yielded information on the early stages of zone formation and growth. Measurements were made also on specimens quenched to and aged at room temperature. From these measurements the previously reported model6 for the later stages of growth is confirmed; namely, the larger zones grow at the expense of smaller ones. Three elements, silver, silicon, and magnesium, were chosen as the third elements for the following reasons: Silver. In the binary A1-Ag alloy the spherical disordered 77' zones were observed immediately after quenching.7 Therefore, in the Al-Zn-Ag alloys, it is suggested that silver atoms might induce cluster formation during quenching. Also, since the migration energy of the zinc atoms was found to be raised by the addition of silver atoms,' silver atoms may have a great effect of the zinc diffusion, especially during low-temperature agings. Silicon. The effects of the addition of silicon atoms were found to be marked, especially at low-tempera-ture aging. In the binary Zn-Si system, no mutual solid solubilities between silicon and zinc9 and no in-termetallic compounds10 are reported to exist. Shashkov and Buynov11 investigated the behavior of silicon atoms in Al-Zn alloys and showed that silicon was not in the G.P. zones. The interaction between silicon atoms and vacancies is strong enough to increase the quenched-in vacancy concentration.* Magnesium. Magnesium atoms are reported to trap quenched-in vacancies and after much longer aging times these trapped vacancies will become free and act as diffusion carriers.13 Therefore at intermediate aging times, the diffusion of zinc atoms in Al-Zn-Mg alloys will be slower than in the binary Al-Zn alloys, whereas at longer times zinc diffusion will become faster. EXPERIMENTAL PROCEDURE The alloys used in this investigation had compositions of 4.4, 6.8, 9.7, and 12.4 at. pct Zn with or without 0.1 and 0.5 at. pct Ag, Si, or Mg. The alloys were prepared from high-purity aluminum, zinc, silver, silicon, and magnesium, with each metal having a purity better than 99.99 pct. The analyzed composition of the specimens is given in Table I. The measurements of the X-ray small-angle scattering were carried out with foils of 0.20 mm thick. The change of the scattering intensity was always measured at the fixed scattering angle of 20 = 2/3 deg. This angle exists nearly on the position of the intensity maximum. The value of the interparticle interference function14 which has large effect in this range of angles may not change abruptly in the case of the spherical shape of small zones. Therefore, from the above considerations, it is concluded that an increase of the intensity measured at this constant angle corresponds to an increase of the average radius and volume fraction of G.P. zones. The specimens were homogenized at 500°, 450°, and 300°C for 1 hr in an air furnace. For the study of the formation and growth at low temperatures, the foil

Jan 1, 1970

By R. Varbanov, D. Nikolov, I. Nishkov

An interesting new flotation technique which reportedly improves mineral recovery over an extended particle size range-from 3 mm to 5 microns and below-has been developed by the Institute of Physical Chemistry, Bulgarian Academy of Sciences. Designated the "static" flotation technique, it is suited for upgrading tin, molybdenum, tungsten, uranium, gold, copper, lead, zinc, and other metallic ores. Recoverable nonmetallics include feldspar, sulfur, and phosphorite. Characteristic of the static flotation process are: •longer contact period (up to 1000 times longer between particles and bubbles, •low collision velocity and inertial forces between the contact and aeration in a thin pulp layer, • aeration without the harmful hydrodynamic repulsion upon particles below 5 microns (the pulp layer is only a few millimeters thick and rising bubbles collide with the particles either directly or in the thin foam films formed), •option to conduct the process with or without froth by film flotation at equilibrium contact angles, and • the use of inexpensive frothers and/or unstable froth with separate regulations of froth stability by hydrodynamic, ultrasonic, or electrostatic means.

Jan 10, 1979

By G. Rowan, M. W. Clegg

The basic equations for the flow of gases, compressible liquids and incompressible liquids are derived and the full implications of linearising then discussed. Approximate solutions of these equations are obtained by introducing the concept of a disturbed zone around the well, which expands outwards into the reservoir as fluid is produced. Many important and well-established results are deduced in terms of simple functions rather than the infinite series, or numerical solutions normally associated with these problems. The wide range of application of this approach to transient radial flow problems is illustrated with many examples including: gravity drainage of depletion-type reservoirs; multiple well systems; well interference. INTRODUCTION A large number of problems concerning the flow of fluids in oil reservoirs have been solved by both analytical and numerical methods but in almost all cases these solutions have some disadvantages — the analytical ones usually involve rather complex functions (infinite series or infinite integrals) which are difficult to handle, and the numerical ones tend to mask the physical principles underlying the problem. It would seem appropriate, therefore, to try to find approximate analytical solutions to these problems without introducing any further appreciable errors, so that the physical nature of the problem is retained and solutions of comparable accuracy are obtained. One class of problems will be considered in this paper, namely, transient radial flow problems, and it will be shown that approximate analytical solutions of the equations governing radial flow can be obtained, and that these solutions yield comparable results to those calculated numerically and those obtained from "exact" solutions. It will also be shown that the restrictions imposed upon the dependent variable (pressure) are just those which have to be assumed in deriving the usual diffusion-type equations. The method was originally suggested by Guseinov,1 who (a) postulated a disturbed zone in the reservoir, the radius of which increases with time, and (b) replaced the time derivatives in the basic differential equation by its mean value in the disturbed zone. In this paper it is proposed to review the basic theory leading to the equations governing the flow of homogeneous fluids in porous media and to consider the full implications of the approximation introduced in linearising them. The Guseinov-type approximation will then be applied to these equations and the solutions for the flow of compressible and incompressible fluids, and gases in bounded and infinite reservoirs obtained. As an example of the application of this type of approximation, solutions to such problems as production from stratified reservoirs, radial permeability discontinuities; multiple-well systems, and well interference will be given. These solutions agree with many other published results, and in some cases they may be extended to more complex problems without the computational difficulties experienced by other authors. THEORY In order to review the basic theory from a fairly general standpoint it is proposed to limit the idealising assumptions to the minimum necessary for analytical convenience. The assumptions to be made are the following: 1. That the flow is irrotational. 2. That the formation is of constant thickness. 3. Darcy's Law is valid. 4. The formation is saturated with a single homogeneous fluid.

By H. J. Hager, P. H. Haskell

Fox the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wettable plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to retreat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both by-product coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to l00 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands 1 in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within ±0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation's mines could not clean the fine sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to 0. The washed table coal is mixed with the 3 to ¼ -in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1941

By H. J. Hager, P. H. Haskell

For the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wet-table plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to re-treat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both byproduct coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to 100 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands I in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within +0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation's mines could not clean the he sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to o. The washed table coal is mixed with the 3 to ¼-in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1942

By H. J. Hager, P. H. Haskell

For the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wet-table plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to re-treat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both byproduct coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to 100 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands I in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within +0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation's mines could not clean the he sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to o. The washed table coal is mixed with the 3 to ¼-in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1942

By Harry R. Cedergren

Properly designed drainage systems can be of great benefit to many kinds of Civil Engineering works, including embankments, and often are the most economical way to protect such works from the damaging effects of water. To function properly, drains must be able to remove water without also removing soil or becoming clogged with soil or erodible rocks. The first criterion to be used in designing drainage systems, called the filter criterion, can prevent all such problems (erosion and clogging) when properly fulfilled in design and construction. The second requirement of drains is that they must be capable of removing all of the incoming water without the build-up of large amounts of head that can damage the protected works. To insure this kind of perfomance, the discharge capabilities of drains should always be verified by appropriate hydraulic and seepage calculations. This paper describes these two basic drain design criteria and also gives examples of application of seepage principles to the evaluation of the potential benefits of drains and to the design of drains for mine waste embankments.

Jan 1, 1985

By J. C. Swartz

Measurements of the effect of precipitation stresses on the solubility of cementite (Fe3C) precipitates in a iron are reported. Solubilities were determined from measurements of the Snoek relaxation due to interstitial carbon after quenching from various equilibrium treatments. Stress-free precipitates were obtained by a spheroidizing treatment of vacuum-melted Fe 0.06 wt pet C. Subsequent equilibration treatments were designed to suppress nucleation of other precipitates. The results for stress-free cementite give a heat of solution of 14.8 i 0.2 keal per mole and an entropy change of 1.1 i 0.2 eu in the temperature range 400" to 715°C. Comparison with previous data indicates that the heat of solution increases about 6 keal per mole as temperature increases from 700" to 1000°C. Data on self-stressed cementite in quench-aged specimens of Fe 0.013 wt pet C indicate 1) an apparent heat of solution of 12.1 i 0.4 keal per mole in the range 280" to 690°C, 2) a strain energy of- 1.1 keal per mole Fe3C accompanying precipitation at 280°C, and 3') a gradual decrease in the strain energy of precipitation with increasing equilibration temperature. In com-parison with 2 and 3 the strain energy calculated for an isotropic model is 1.7 keal per mole Fe3C. The lower values obtained from the experiment indicated substantial stress velaxation by dislocation motion. WHEN a supersaturated solution of carbon in a iron is aged at temperatures in the range 200o to 700oC, the carbon clusters by interstitial diffusion and forms cementite (Fe3C) precipitate particles. Unstressed cementite has a volume per iron atom 9 pet higher than that of a iron;' hence, cementite precipitate particles are usually under pressure from the iron matrix. The pressure would tend to increase the solubility of cementite in iron.' This report describes anelastic measurements of the solubilities of self-stressed and stress-free cementite in a iron. Previous determinations of the cementite solubility are summarized in Table I. The method of cementite formation for each reference was studied to ascertain the state of stress of the cementite. The results judged to be for stress-free and stressed cementite are distinguished in the table. In the next section an estimate of the stress effect is obtained which is clearly too small to account for the large difference between the previous results in parts A and B of the table. THEORETICAL Let AGO be the standard free-energy change of the reaction Fe3C (eem.) = 3Fe (a) + C (in a) [1] in the absence of stresses. Since cementite precipitates appear to be rather pure10 and the carbon is so dilute in the iron,8 the cementite and iron of Eq. [ I] for the stress-free case have essentially unit activities and the activity of carbon equals its atom fraction xoC Then the stress-free equilibrium is expressed by RT In XoC = -?GO 121 To first approximation the change in the chemical potential of carbon due to the precipitation stresses equals the elastic strain energy W accompanying precipitation of a mole of cementite.2 Hence, in the presence of the precipitation stresses the equilibrium is described by RT In x sq = -?G° + W [3] where xsC is the mole fraction of dissolved carbon in the stressed case. An approximate value of W can be obtained from analysis of the inclusion problem in elasticity theory. The inclusion is a small portion of the matrix phase which has suffered a transformation while still imbedded in the matrix. In the absence of the constraint of the matrix the transformation would be equivalent to a uniform dilational strain eT. Both the matrix (a) phase and inclusion (0) phase are assumed to be homogeneous, isotropic materials. When the a and 0 phases have the same elastic moduli, which is approximately true for iron and cementite,11 the total strain energy per mole ß is12 2µVß(eT)2(3 +4 µx)-I [4]

Jan 1, 1968

By J. D. Wood, J. T. Smith

ALLOYS with a dispersed second phase in a metallic matrix are generally much stronger than the matrix itself. Plastic deformation in dispersion-strengthened alloys is usually confined to the matrix phase when recovery processes are active, while in the absence of recovery both phases may yield.' The alloy system studied in the present research was WC-12 wt pct Co and consisted of noncoherent WC particles dispersed in the cobalt matrix. Some particle-to-particle contact existed but not enough to produce a continuous WC skeleton. The microstruc-ture of the WC particles was characterized by very straight edges, forming a trapezoidal shape in any plane of polish. Previous investigations with WC-Co alloys at room temperature have shown that fracture of the WC particles occurs in transverse rupture testing.' Room-temperature slip was reported for WC particles after indentation for hardness measurements.3 Elevated-temperature deformation of WC particles in a WC-12 pct Co alloy was suggested by recent electron microscope studies of specimens deformed at 900' to 1000°C.4 In highly deformed alloys, the WC edges were serrated in contrast to the usual straight or smooth appearance. WC-12 pct Co and WC-15 pct Co alloys have been previously studied under elevated-temperature com-pressive-creep conditions by the present authors. Electron microscope studies of two-stage replicas from deformed specimens showed no evidence of slip or fracture of the WC particles. These specimens were brought to temperature and allowed to equilibrate prior to the application of the creep load. It was believed that the load-application rate, a crosshead speed of 0.005 in. per min on an Instron universal testing machine, was sufficiently low that recovery within the cobalt matrix was sufficient to limit the deformation to this matrix. A series of experiments was performed to evaluate the influence of loading rate on the deformation of WC-Co alloys. A WC-12 pct Co alloy was selected for these determinations. The average WC particle size was 4.45 p with an average linear separation between particles of 0.59 p. The selected temperature was 800°C and was monitored with a Chromel-Alumel thermocouple attached to the specimen. Testing was conducted in an argon-atmosphere chamber to prevent oxidation of the WC-Co specimens. This chamber was mounted on an Instron universal testing machine equipped to apply the load at a fixed rate. Each specimen was loaded to 110,000 psi compression stress at 0.05 and 0.5 in. per min. The loading rate was monitored prior to insertion of the test chamber and was found to be almost precisely the nominal rate selected. The specimens were raised to temperature and held to equilibrate with the surroundings, and then the load was applied and held for 4 hr to duplicate the exposure time utilized for the creep specimens. The time to reach full load at a crosshead speed of 0.005 in. per min was some 500 sec and was reduced to 50 and 5 sec as the loading rate was increased to 0.05 and 0.5 in, per min, respectively. The model developed by Ansell,' when recovery processes do not occur, considers that fracture or deformation of the dispersed particles is necessary to relieve back stresses on dislocation sources and allow dislocations piled up against particles to sweep out in the matrix to cause plastic deformation; he further states that, even at elevated temperatures, the dispersed-particle deformation is necessary for yielding in the absence of recovery. For the case of straight dislocation segments piled up against a straight barrier, such as the straight-sided WC particles, the shear stress, 7 exerted on a particle is: where h is the spacing between particles (0.59 p), a is the applied stress (110,000 psi), p, is the shear modulus of the matrix (6.7 X lo6 psi at 80O°C), and b is the Burgers vector of the matrix dislocation. From Eq. [I], the shear stress, 7, exerted on the WC particles when no recovery occurs is of the order of 6 X lo6 psi at 800°C. The limiting stress, F, that will

Jan 1, 1969

By E. S. Machlin, W. R. Yankee

IN a previous study1 of the effect of heating com-mercial titanium in air on its subsequent friction coefficient against other metals, as well as itself, it was found that the friction coefficient markedly decreased from a value of about 0.7 to about 0.3. A tentative explanation was given that surfaces normally produced at room temperature are not contaminated sufficiently to prevent seizing or welding of the titanium to the softer mating metals. The latter tend to cleanse themselves during rubbing over the harder titanium. It was thought that the lack of a contaminant protective film on the titanium was due to the high solubility of titanium for oxygen and nitrogen and hence an inability to form a contaminant oxide or nitride. This explanation requires the ratio of the surface absorption rate to the diffusion rate to become much lower at room temperature than it is at high temperatures. In order to check the phenomenon further, commercial titanium specimens were nitrided or oxidized at 800°C for 20 hr in flows of prepurified N2 and 01, respectively, at about 1/2 in. H2O above atmospheric pressure. Friction runs were made in argon using a freshly cut copper hemisphere (cut in argon) on surfaces cut successively into the diffusion layers in the titanium (cut in argon) using the techniques described in a previous publication.' DPH values (100 gram load) were made as a function of depth into the diffusion layer using a Tukon tester. Also, micrographs were taken at separate cross sections to indicate the diffusion layers. The results obtained are presented in Figs. 1 and 2, which show the "static" friction coefficient vs hardness for the nitrided and oxidized specimens, respectively. A separate measurement of the friction coefficient of clean copper vs iodide titanium also was made. From results reported in the literature' giving the oxygen and nitrogen contents as functions of the hardness, cross plots were made showing the friction coefficients as functions of the amount of interstitial solute. These plots are given in Figs. 3 and 4. From micrographs of the diffusion layers and the phase diagrams, it was deduced that the data in Figs. l through 4 correspond to the single phase a region. The points observed on the compound regions have been excluded from the figures. It is apparent that nitrogen or oxygen in solution in the a titanium markedly affects the friction coefficient against a softer mating metal. Discussion of Results These results are extremely interesting from both a practical and theoretical viewpoint. The theoretical implications will be discussed first. According to Bowden, the friction coefficient should be given to a good approximation by the relation where a is the fraction of contact area that has welded, a is the shear strength of weaker component, and H is the hardness of softer component. Using this relation alone, it is difficult to understand the results because none of the terms should be affected by a variation in the oxygen or nitrogen content of the harder and stronger metal, titanium. Even if the ratio of S/H for titanium is used in Eq. 1, the ratio has been shown to be independent of oxy-gen or nitrogen content.' If a more rigorous equa-tion is used combining Eq. 1 and a result given pre-viously" for the case where welding is absent, then the relation obtained is µ = a S/H + (1-a) a W aß/H where a is constant and Waß is the work of adhesion between the two metals comprising the friction couple. This relation states that if a is less than 1/2 or so, variation in the work of adhesion Waß between copper and the titanium should affect the friction coefficient markedly. It is reasonable to expect that the work of adhesion will depend on the oxygen or nitrogen content of the titanium. Available data4 show that clean metals and oxides have much lower works of adhesion than the same metals against the

Jan 1, 1955

By Eugene Stephenson

CRITICAL analyses of the work expended in producing oil by the utilization of gas energy have appeared in the publications of Shaw,1 Pierce and Lewis,2 and Herold,3 authors who have ably discussed the factors which must be taken into consideration in comparing energy consumed per barrel in various wells which are flowed by means of gas-lift. However, two distinct phases of oil production are concerned with the ratio of gas energy consumed to oil produced. One of these phases is the gas-lift, which utilizes the differential gas pressures for the purpose of flowing oil, whether these pressures be natural reservoir pressures or be induced by artificial compression of gas or air. The other phase has to do with prorating oil production in pools which are operated either as units, or are subject to such restrictions as those imposed at Oklahoma City by the Corporation Commission, or, by similar controlling groups in other fields. An abundance of literature is available relative to the problems of flowing wells by gas-lift, but the first suggestion that the energy of the gas within the oil and gas pool might serve as a basis for proration, appeared in the timely article by McWilliams.4 Much of the. dissatisfaction with proration in certain fields is because some operators feel that besides the hazard to the wells which accompanies the test, the method of allocating production on the basis of the "potential" gage is inequitable and gives some operators a distinct advantage over others.5 The most severe penalty may be exacted from the most progressive operators or those who attempt to produce their oil with a minimum quantity of reservoir gas. If :no difficulties ever

Jan 1, 1931

By E. K. Landis

IK connection with the interesting paper of Mr. Glenn on "Sampling Ores Without Use of Machinery " (page 156 of the present volume), I venture to offer the results of ten years' experience in the sampling of iron-ore by a method adopted when I first became

Jan 1, 1892

Jan 1, 1903

By C. C. Miller, A. R. Belyea, C. H. Herty, E. B. Burkart

The removal of sulfur from steel has been studied by many investigators, but the quantitative relationships between the factors involved have not been determined. This is undoubtedly due to the number of variables encountered in practice, an attempt to study any one reaction or relation being affected by other reactions the relative importance of which cannot be estimated. The factors that affect the extent of removal of sulfur in the basic open-hearth process are generally considered to be: 1. Basicity of the slag: (a) Iron oxides in the slag; (b) carbon in the metal or carbide in the slag; (c) temperature. These factors affect the reactions: FeS + CaO = CaS + FeO FeS + CaO + C = CaS + CO + Fe. 2. Amount of sulfur in the gas. 3. Amount of manganese in the metal. The factors which affect the rate of removal of sulfur include, in addition to these: 4. Fluidity of the slag: (a) Normal changes in fluidity with temperature; (b) changes in fluidity because of the addition of special reagents such as fluorspar. 5. Agitation of the bath. Within the past two years, two papers have been presented dealing with the influence of sulfur in the gas on slag and metal. Nead' has shown that if a gas high in sulfur be used for heating, the metal and slag will absorb sulfur. Whitely2 concluded from his experiments that if a

Jan 1, 1925

By Arthur L. Hall

The purpose of this symposium is to challenge industry to better air classification, and as a first step toward fulfillment, to spotlight three fairly recent, aerodynamically designed, highly efficient air classifiers. This discussion does not intend to imply that present practice is bad. Actually, when present air separators are used for the jobs for which they were originally designed, they give high production and uniform operation, with a minimum of maintenance. The customers of nonmetallic mineral pigment producers, however, are making increasing demands for finer products, such as 99.9 pct -20µ, which appears to be beyond the economic capabilities of standard air separators industrially used over the last 10 to 30 years. Here is an actual example. A 10-ft diam pebble mill is in closed circuit with a conventional 12-ft diam centrifugal air separator, grinding 20-mesh wollastonite to a series of fine grades up to 99.97 pct - U.S. No. 325 mesh (44µ). Fig. 1 shows variations in fineness of mill discharge (or air separator feed), recycle for regrinding (or air separator tails), and product as measured by a wet rotating sieve test. For example, when the mill is turning out a product 80 pct -325, the mill discharge or separator feed is 30 pct -325, and the coarse tailings or recycle is only 5 pct -325. Hence 25 pct of the 30 pct available is accepted as product. This is efficient separation, and the ratio of recycle to feed is only about 2: 1. How- ever, to make a product testing 99.97 pct -325 the separator feed is 62 pct -325 and the coarse tailing 60 pct -325. In this case the recycle ratio is about 13: 1 and the economic limit to produce fineness has been substantially reached with this given equipment and process arrangement.

Jan 10, 1957

By R. W. Carpenter, J. C. Ogle

It is possible, by using pack-rolling instead of conventional rolling, to reduce a number of metals to thicknesses of 2µm or less. Such thinfoils are generally made at room temperature without intermediate annealing. In addition, pack-rolled foils fail by developing pinholes at thicknesses near 2µm instead of developing the shear cracks usually observed in cold-rolled ductile metals. This paper presents the results of a general investigation of the deformation substructure and texture developed in copper and iron pack -rolled from 130 to about 2µm thickness. Electron microscopy showed that in both metals a fine (0.2 to 0.5?µ m) deformation subgrain structure formed during pack-rolling; in neither case was this substructure grossly different from substructures formed during conventional rolling. The deformation texture formed in pack-rolled iron was quite similar to usual bcc textures; however, in the case of copper, the cube texture was stable during pack-rolling and the normal copper deformation texture was unstable. It is shown analytically that the constraining pack induced a large hydrostatic pressure in the foils during pack-rolling. The pinhole failure mechanism is attributed to the presence of the large hydrostatic pressure during pack-rolling; this strongly suppressed the growth of shear cracks. The stability of the cube texture in copper is also probably due to the unusuul stress distribution developed during pack-rolling. EXPERIMENTS at several laboratories have shown that very thin foils of the common structural metals and many of the rare earths can be made by "pack-rolling". 1-3 The technique was originally developed to make specimens for nuclear scattering experiments and foils for X-ray filters. It is also useful for making experimental laminar metallic composite bodies and foils thin enough for direct examination by ultra-high voltage electron microscopy without the need for special thinning techniques. Pack-rolling in the present context means a three-layer pack, with the material to be rolled into foil comprising the center layer. The outer two layers, which constrain the foil during reduction, are ordinarily austenitic stainless steel. Typically, a 130 µm (0.005 in.) metal strip can be reduced to a final thickness of 2 µm or less by this process. This is accomplished at room temperature, without intermediate annealing. It has been observed that foils produced by this process do not exhibit at any stage of their reduction the severe work-hardening found in strip rolled by conventional cold-rolling methods. Neither is the failure characteristic the same."&apos; Conventionally cold-rolled ductile metal strip fails by developing shear cracks on planes whose normals nearly bisect the angle between the rolling direction and normal to the rolling plane; these are planes of maximum shear stress. In pack-rolling this mechanism has not been observed; failure occurs by the formation of pinholes on the foil surface (penetrating the foil). If pack-rolling is continued the hole density increases. These differences in behavior imply the existence of appreciably different substructure in pack-rolled foils compared to substructure in conventionally rolled material, or perhaps that the geometry of pack-rolling has an effect on the foil behavior. This paper describes an investigation of deformation substructure and texture in some specimens of pack-rolled copper and iron, and some considerations of the stress distribution in the foils during rolling that result from the geometry of pack-rolling. EXPERIMENTAL DETAILS Three different materials were used for pack-rolling in the present work: soft copper sheet (99.8 pct Cu, 0.03 pct 0, electrolytic tough pitch) and two types of iron, Ferrovac E* and Armco iron. Each was "Crucible Stccl Co. initially in the form of 130 µm annealed strip with grain size ranges of approximately 10 to 40 µm. The initial texture of the copper (determined as noted below) was the normally observed cube type (001)[100]; there was evidence of a small amount of material in the cube-twin orientation reported by Beck and Hu.4 The initial texture of the Ferrovac E was similar to that reported for recrystallized iron by Kurdjumov and sachs,5 who list the principal orientations as {111}<112>, {001}<110> 15degfrom RD and a weak component {112}(110) 15 deg from RD. The starting texture of the Armco iron was not determined. Pack-Rolling Procedure. A four-high mill was used for all specimens. The work roll and backing roll diameters were 1.625 and 5.25 in., respectively. The peripheral roll speed of the work rolls was about 2.5 in. per sec. All foils were initially reduced from 130 to 100 µm by conventional straight rolling and then inserted into a pack, without any intermediate annealing, for further reduction. The pack consisted of an 0.033 in. (838 µm) thick 3 by 6 in. polished sheet of austenitic stainless steel, folded to make a 3 by 3 in. jacket. After folding, the jacket was given a small reduction to close the fold tightly before insertion of the foil. During pack-rolling a constant change in roll spacing was made every third pass. The roll-spacing change corresponded to a 5 pct reduction in thickness for a new pack. This approached a 10 pct reduction when the pack had decreased to about half its original thickness. At this point the deformed pack was discarded and a new one

Jan 1, 1970

By John T. Thorndyke

MOST important of the naturalcalcium silicates is the meta¬silicate, CaSi03, known as wollastonite, after W. H. Wollaston. A large deposit of this mineral was dis¬covered some seven years ago near Code Siding, Rademacher mining dis¬trict, Kern County, Calif., the deposit being some 7500 ft. long and of an average width of 300 ft. It consists of a series of small domes striking north¬erly and southerly and with a dip of 81 ° to the south. This deposit was opened up by a series of small quarries showing a potential tonnage of 12,000,¬000 tons, allowing of cheap mining and transportation, the Southern Pa¬cific R.R. spur track being one mile north of the workings. Numerous sam¬ples taken from different points on the deposit, tested by Mr. Brinker, of the California Testing Laboratories, Los Angeles, showed an average as fol¬lows: Per Cent Silica (SiO2) 47.12 Lime (CaO) 41.72 Magnesia (MgO) 2.72 Alkalies (R,0) Trace Iron (Fe.,O,) 1.60 whereas the theoretical composition of of wollastonite, as given by William Shirley Bayley, is as follows: Silica 51.75 Lime 45.25 The tonnage and purity of this de¬posit led to investigations into its com¬mercial development. Early work es¬tablished the fact that wollastonite was ideal for the manufacture of a tough, almost unbreakable, glass similar to Pyrex. It also established the fact that wollastonite was particularly adapted for use in the manufacture of mineral wool, towards which further research was then directed. Briefly, the prin¬cipal advantages were the substantially unvarying chemical composition of the naturally occurring mineral and its characteristic of being relatively flexi¬ble and highly resilient when fused into a glass. A mineral wool produced therefrom is thus not only of highly uniform composition and color but is most desirable because of the high mechanical strength and length of the individual fibers constituting the wool. It is well known that mineral wool may be prepared by melting a suitable charge of raw material and then intro¬ducing a stream of a suitable fluid, such as air or steam, into a stream of the molten raw material. By this means the molten material is blown into threads or fibers, which are collected in a suitable chamber similar to a tun¬nel, from which they are removed from time to time or continuously. Com¬mercial manufacture of mineral wool has been carried on for only about 50 years, but volcanoes, specifically Kilauea in the Hawaiian Islands, have

Jan 1, 1936

By H. R. Ogden

The notch sensitivity of titanium alloys is affected by impurity content, microstructure, and heat treatment. Using notch tensile properties to evaluate notch sensitivity, three commercial titanium-base alloys were investigated over the temperature range of -320o to 390°F. The alloys studied were Ti-5Al-2.5Sn, Ti-6Al-4V, and Ti-2Fe-2Cr-2Mo. Six interstitial levels were studied for each alloy in four mi-crostmctural conditions. The ff- 0 alloys were studied in both the annealed and heat-treated condition. All tests were conducted using 1/4-in. diam round tensile samples. The notched samples had a 50 pct notch with a notch sharpness (a/r) of 53, corresponding to Kt 6.3. Notch sensitivity was increased by increased interstitial content, low temperature, and acicular-type microstructures. The heat-treated, high-interstitial content - 13 alloys were more notch sensitive than the same alloys in the annealed condition. In addition, minima in the notch tensile-temperature curves were observed at temperatures near 32°F. These minima became more pronounced with increasing interstitial content. 1 HE increaseduse of titanium alloys in high strength applications at subzero temperatures requires that a better under standing of the low-temperature behavior of the alloys be obtained. At low temperatures, metals generally exhibit increased strength with lowered ductility and tohness. Notch sensitivity and the factors which influence it become more important as the strength level is increased and the temperature is decreased. Some of the factor s which affect notch sensitivity in ti- tanium alloys are composition, interstitial content, microstructure, and heat-treatment condition. In this paper, the results of a study of these variables on the notch sensitivity of three titanium alloys at temperatures from —320o to 390o are reported. The notch geometry selected for this program was chosen to provide a severe test of notch sensitivity. The ability of the metal to flow without initiating fracture under these severe conditions is reflected in the notch-strength values. Since notch strength is, in part, determined by the constraint exerted by the combined tensile stresses, the behavior of notch specimens reflects the properties of the material under combined stresses. For example, a material with a high notch-unnotch strength ratio may be expected to withstand the biaxial stresses encountered in a pressure vessel better than a material with a low ratio of notch-unnotch strengths. This implies that maximum strength alone is not a sufficient criterion for applications of this type. It further may be concluded that the various conditions that promote poor notch behavior also will affect adversely the performance of materials under combined stresses. In the alloys studied, these included low temperatures, high interstitial levels, and hasformed microstructures. EXPERIMENTAL PROCEDURES Three alloys, Ti-5Al-2.5Sn, Ti-6Al-4V, and Ti-2Fe-2Cr-2Mo, were purchased from commercial producers as 2-in.-dam rod stock. Oxygen and nitrogen were added to these alloys by remelting to obtain a variety of interstitial contents as shown in Table I. In order to Compensate for the much more potent strengthening effect of nitrogen compared with oxygen, an oxygen equivalent content is used to describe the total oxygen plus nitrogen contents studied. It has been suggested previously1 thatnitro-gen is approximately twice as effective in strengthening as oxygen, and carbon, to the extent it is in so-

Jan 1, 1962

By S. Shapiro, G. Krauss

RECENT investigations1 3 of the products of marten-sitic transformation in Fe-Ni and Fe-Ni-C alloys have made use of light microscopy to describe mar-tensitic fine structure. The application of conventional metallographic techniques to this problem was possible because of the similarity of distributions of parallel striations developed by etching polished surfaces to distributions of transformation twins which are positively identified in thin films by transmission electron microscopy. The surface striations frequently are not well-defined, and could also be due to, for example, rows of etch pits which are not resolved by the light microscope. This note describes the etching effects revealed by examination of surface replicas of mar-tensite in the electron microscope. The application of a replica technique both extends the observations of fine structure made with the light microscope and allows the results of conventional metallography to be used with more confidence. Samples of an Fe-33 wt pct Ni alloy were used for this study because of the detailed knowledge of the fine structure of martensite which has been developed&apos;-4 for alloys of about this composition. Samples transformed to martensite at -120°C, and transformed samples heated to 340°C to effect a small amount of reversal of martensite to austenite, were examined. Surfaces were first prepared for replication by elec-tropolishing in a chromium oxide-acetic acid electrolyte at a current density of 0.1 amp per sq cm and a temperature of 15°C or a perchloric acid-acetic acid electrolyte at a current density of approximately 2 amps per sq cm and a temperature of 15°C. The polished surfaces were then etched for 4 to 7 sec by immersion in a solution of equal parts HC1, HNO,, and H20. Application of the etchant for this period of time produced discrete attack of certain features without loss of resolution due to overlapping of areas most susceptible to etching. The etched surfaces were replicated by 1) preshadowing with Pt-Pd alloy at an angle of 20 to 30 deg, 2) depositing a thin carbon film, and 3) stripping the film and shadowing material by immersion in a 5 pct nital solution. Two types of etching effects were observed by examination of the surface replicas in the electron microscope: l) continuous striations centered at the bottom of long grooves or the tops of pyramidal elevations on the sample surface, and 2) high densities of fine etch pits. Examples of both types of features are shown in Figs. 1 to 4. The striations are in each case continuous and have the same characteristic configurations as do transformation twins in martensite. Fig. 1 shows that the density of grooves decreases toward the edge of a martensite plate and Fig. 2 shows a region where the striations are of varying length. Similar examples of transformation twin arrangements determined by transmission electron microscopy of thinned foils of martensite have been shown in the literature,&apos;~ and, based on these similarities, the striations and their associated grooves or mounds are considered to be evidence for the presence of transformation twins. The transf~rmation twins in martensite are on the order of l00 A thick, much too fine for resolution by the light microscope. It appears that orientation-dependent etching of the matrix martensite about the twins results in grooves or surface elevations which

Jan 1, 1967