Search Documents

By Gerhard Derge, J. Warren Stewart

Extrusion processes are used in the commercial production of a wide variety of products, as indicated by the review presented a few years ago by D. K. Crampton.' Most writers have confined themselves to a general description of the equipment and products and the engineering aspects of the process. The few studies that have dealt with the metallurgical side of extrusion have been concerned primarily with an examination of the mode of flow of the metal during extrusion. This has been accomplished by the use of composite billets, by scribing grids on symmetrical sections of billets and observing the change of dimensions in the gridwork, or by examining microstructures in extruded sections.2"8 Ariotlier limitation of these original studies is that they were confined to the extrusion of very simple shapes, usually rods having a diameter of about one-fourth that of the billet. Tin is particularly well suited to the extrusion of collapsible tubes and similar shapes in which the extruded section is very small in comparison to the diameter of the billet or slug. In modern production, impact extrusion methods are generally employed, therefore the thickness of the slug is small compared to its diameter. Under these conditions the process differs considerably from the processes that have been most fully described in the literature, and it is known that the quality of the product is very sensitive to slight variations in any one of the many variable factors involved, such as coinposition and structure of the alloy, rate of extrusion, temperature, shape of punch and die. An exhaustive examination of all of the above-mentioned problems promises to produce so many data that it seems advisable to initiate the reports at this time, even though all of the factors outlined have not been examined fully, and to confine this paper to a description of the apparatus and method. Only tin and its alloys with small amounts of copper have been considered. These are the alloys most commonly used in this country for the production of the type of articles already described.

Jan 1, 1940

By Matsubara, A.

THE problem of the equilibrium between iron, carbon, and oxygen was first carefully investigated by E. Baur and A. Glaessner,1 who determined the equilibrium conditions of the two reactions Fe304 + CO ? 3FeO + C02 (1) FeO + CO ? Fe + C02 (2) within the range of temperature of 350 to 900° C. The next series of investigations was made by R. Schenck and his co-workers,2 who sought to check the results of Baur and Glaessner's work within the range of 550° to 700° C. and to elucidate the conditions of formation of iron carbide. The equilibrium conditions at the higher temperatures, however, are generally understood to be much more complicated, owing chiefly to the formation of solid solutions between iron, its oxides, and carbide; nevertheless their determination is of much more practical importance than those at the lower temperatures. It is well known that each of the reactions is reversible; equilibrium is established when the partial pressure of oxygen in the gaseous phase has become equal to the dissociation pressure of magnetic oxide in equation 1 and that of ferrous oxide in equation 2. These equilibria are subsequently designated by "the Fe304-FeO equilibrium" and "the FeO-Fe equilibrium," respectively. As the Fe304-FeO equilibrium has three phases with three components, it must be bivariant. But the reaction involves no pressure change in the gaseous phase, hence the final composition of the latter is practically unaffected by pressure. To know, the equilibrium conditions, the compositions of the gaseous phase at different temperatures must be determined. At the higher temperature, however, iron and its oxides dissolve one another in various proportions forming solid solutions; in many cases the content of oxygen in the solid phase becomes a new independent variable.

Jan 2, 1921

By Ivor Hawkes

A wide variety of borehole gages have been developed for measuring rock stress. They all operate on the principle that stress changes around a borehole result in deformation that can be measured by the gage and interpreted in terms of the stress change either by calculation or calibration. In general terms, gages that comply with the borehole deformations are referred to as “deformation meters” and those that restrain the deformations by reason of their rigidity are referred to as “stress meters.” The main advantages claimed for stress meters are: their “stress” sensitivity is much less dependent on the rock modulus than that of deformation meters, and they are clamped firmly in the borehole. The use of each of the borehole gages developed for stress determinations in rock in the main has been confined to the laboratory responsible for its development. To be generally accepted a gage must meet the following specifications : 1) Gages to be left in place to measure stress changes must be relatively cheap, and if possible recoverable, so that large numbers can be used to obtain an overall picture of the changing conditions. This, of course, is not necessarily the case for recoverable gages designed for absolute rock stress measurements where usually only one or two gages are involved. 2) For use in the adverse environmental conditions encountered underground, it is essential that gages be robust, stable, and unaffected by high humidity, corrosive water, or dust. 3) Highly qualified technicians are rarely employed specifically for rock mechanics studies in mines or on civil engineering sites and there- fore gages designed for measuring stress changes must be easy to set and

Jan 1, 1972

By J. C. Swartz

New measurements of graphite and cementite solubilities in ferrite have been obtained to resolve disagreements among previous data. To measure graphite solubility, specimens of iron were equilibrated with rarious carburizing atmospheres at temperatures be-twee~z 480" and 1435°C. The carbon activity of each atmosphere relative to graphite was taken from published data. After quenching from each equilibration treatment the concentration of carbon (typically 10 pprn by wt) was determined from the height of the Snoek peak in the internal friction spectrum. A few inclividual analyses by combustion support the reszdts of Smith on the solubility of graphite near the eutectoid temperature. Combination of these combustion and internal friction analyses determines In a, (at 0.01 wt pct) = 24,000/RT - 12.72, where a, is the activtity relative to graphite in ferrite at fixed cornposition. The same specimens were used to determine the solubility of self-stressed cementite precipitates. The results indicate solubilities of 6.3, 23.2, and 68 pprn carbon by wt at respectively 400°, 500". and 600°C. The once large discrepancy between the cementite solubility determined by internal frictiori and that calculated from flee energy data has been almost completely resolved. A recent study1 (hereafter designated I) on the solubility of cementite in a iron did not fully resolve the disagreement among previous data. The remaining disagreement is illustrated by the phase diagram in Fig. L The data of I are represented by the line labeled "stress-free" cementite. They determine a heat of solution of cementite of (14.8 * 0.2) kcal per mole which contrasts with the (20 * 1) kcal per mole derived from Smith's graphite solubility2 and the formation energy of cementite.3 Toward resolving this disagreement we have obtained new data on the solubilities of graphite and cementite. METHODS As in I the Snoek peak in the internal friction spectrum was used to measure the concentration of carbon dissolved in ferrite. This method relies on the relation C=kQ-1 [1] in which C is the concentration of dissolved carbon, Q-I is the Snoek peak height, and k is a proportionality factor which is a function of the peak temperature, polycrystalline texture, and other parameters characteristic of the ferrite lattice. To determine true heats of solution via Eq. [1], it is necessary to establish that k is independent of the temperature from which the specimen is quenched. Some evidence on this point is contained in a separate report.* Additional evidence is shown by the data points in Fig. 1. These represent the Snoek peaks of two specimens carburized to about 10 ppm C, copper plated, and quenched first from 888º then from 588°C. The copper plate was removed before each Snoek peak measurement. These data show that there is no detectable dependence of k on quenching temperature. The solubility of graphite was determined by repeatedly carburizing various specimens of iron wire with gas mixtures of known carbon activity relative to graphite. To cover a wide temperature range within the a phase boundaries it is desirable to use as low a carbon concentration as is compatible with reasonable precision. With the present internal friction apparatus the best compromise of these desires is a concentration near 10 wt ppm. The dashed line in Fig. 1 was used to approximate the activity of carbon* for

Jan 1, 1970

By F. O. Blackwell

It is roughly estimated that some three hundred companies in the United States engaged in mining and the kindred arts now employ electricity in their operations. As all these plants have been installed within the last few years, it is evident that mining engineers have been quick to appreciate the great advantages of the use of electricity and adopt it for their many requirements. In

Jan 1, 1894

By G. L. Chierici

Starting from Muskat's theory of water and gas coning, maximum permissible oil production rates without water and/or free-gas production have been determined, in a broad range of reservoir and well parameters, using the potentiometric model technique. The main assumptions made are as follows: (1) the reservoir rock is homogeneeous (either isotropic or anisotropic); (2) the volume of the aquifer underlying the oil zone is very small, so that it does not contribute to reservoir energy; and (3) the gas cap expands at a very low rate, so that it can be assumed to be in quasi-static conditions. The results obtained are presented in the form of diagrams which can be used for solving two types of problems: (1) given the reservoir and fluids characteristics, as well as the position and length of the perforated interval, determine the maximum oil production rate without water and/or free-gas production; and (2) given the reservoir and fluids characteristics only, determine the position and length of the perforated interval which optimize the maximum permissible oil production rate, without water and/or free-gas production. INTRODUCTION In oil reservoirs where the oil-bearing formation is underlain by an aquifer which does not participate in the production mechanism, water-coning is a limiting factor to the flow rates of producing wells. Production rates are usually kept to a value that will prevent the water from entering the wells. The entry of water into a well lowers its productivity by increasing the weigbt of the fluid column; moreover, the separation of water from the effluent, at the surface, may constitute a very difficult problem in cases of heavy viscous oils. A similar situation is encountered in oil reservoirs with a gas cap overlying the oil-saturated zone; here a downward gas cone is induced by the flow of oil towards the producing wells. Production rates must be low enough to prevent the gas from being produced; producing gas from the gas cap would be a waste of energy. Of course, water-coning and gas-coning phenomena can occur at the same time in the same reservoir if the oil-producing formation is both overlain by a gas zone and underlain by a water zone. Due to its relevant practical importance, the mechanism of coning was studied by many people.2,3,5-8 Defining the conditions for getting the maximum water-free and/or gas-free oil production rate is a difficult problem, often encountered under one of the following aspects: 1. Predict the maximum flow rate that can be assigned to a completed well without the simultaneous production of water and/or free-gas. 2. Define the optimum length and position of the interval to be perforated in a well, in order to obtain the maximum water and gas-free production rate. A systematic study of these problems was made by means of the electrical analog technique. The results of this study are presented here, under the form of a set of curves providing solutions for the above stated problems. These curves are valid only for homogeneous forrnations, either isotropic or anisotropic. Should the formation be non-homogeneous (by horizontal or vertical variation of permeability, shale diaphragms, fractures, etc.), a specific potentiometric study would be required for each specific case. Especially when shale diaphragms of some radial extension are present, the critical rates observed are much larger than would be expected from the diagrams. STATEMENT OF THE PROBLEM In the present study the aquifer is supposed to be of such limited volume that it does not contribute to the energy of the reservoir. Moreover, the gas cap is supposed to expand at such a low rate that the potential gradient in the gas cap is negligible. Under static conditions water-oil and gas-oil interfaces (T1 and T2) are both horizontal. When the reservoir production starts, below each well these interfaces take a cone-like shape (Fig. 1) having as an axis the axis of the well. This shape results from the equilibrium between potential gradients in the oil zone and gravitational forces due to density differences between oil and water and between oil and gas. Assuming the oil-bearing formation to be homogeneous and the oil to be incompressible, the analysis of the problem (see Appendix) shows that the oil-water and gas-oil interfaces are stable only if the oil production rate of the well is not higher than the following values.

Jan 1, 1965

By E. H. Hamilton

THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total 100.0 THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total?100.0?20,580

Jan 1, 1924

Organization Place Date 1919 Automotive Engineers New York, N. Y. Feb. 4-6 American Institute of Mining Engineers New York, N. Y. Feb. 17-20 New England Association of Gas Engineers Boston, Mass. Feb. 19 American Institute of Electrical Engineers New York, N. Y. Feb. 19-21 National Society for the Study of Education Chicago, Ill. Feb. 25-28 American Railway Engineering Association Chicago, Ill. Mch. 18-20 American Electrochemical Society New York, N. Y. Apr. 3-5.

Jan 2, 1919

By B. B. Cox

Iraq, formerly called Mesopotamia in Asiatic Turkey, became a kingdom under British Mandate after the world war and is expected to gain its independence in 1932 when it enters the League of Nations. The kingdom is shown on Fig. 1 in its relations to neighboring countries, to the Mediterranean Sea and to the Persian Gulf. It is slightly smaller than the State of Texas with its capitol, Baghdad, inland about as far from the Persian Gulf as Breckinridge, Tex., is from the Houston Shipping Channel. The oil fields lie 180 to 225 miles north of Baghdad, or about as far as from Breckinridge to Oklahoma City, and about as far from the Mediterranean as Fort Worth is from Hobbs, N. M. A narrow-gage railway runs from Basra, the Persian Gulf port, to Baghdad. From there another narrow-gage runs into the Kurdish hills east of the Tigris to Kirkuk. A standard-gage, part of the old Berlin-Baghdad system, follows the west bank of the Tigris northward from Baghdad to Baiji, a village about 100 miles south of Mosul. No railway exists between Iraq and the Mediterranean, though the Anatolian Railways in southern Turkey come to within 50 miles of the Iraq frontier and 120 miles of Mosul. Surveys have been completed for a railway through British Mandates from Haifa to Baghdad as well as for a railway through French Mandated Syria from Tripoli to Abu Kemal near the Iraq border. Wagon roads, excepting those constructed by the oil companies, are few and indifferent in Iraq and no road exists across the desert to the Mediterranean, but contrary to prevalent beliefs the surface is firm and free from sand dunes so that motor cars can go almost anywhere in dry weather, with ease. Frequent motor car and airplane service exists between Baghdad and the Mediterranean ports and motor car service may be had between Kirkuk and Nisibin, Turkey, where on two days each week through Wagons Lits service is available to Paris. Baghdad is about 21 days distant from New York City with present transport facilities. The climate is semiarid, similar to Imperial Valley, California, the average rainfall outside the mountainous parts amounting generally to

Jan 1, 1932

Jan 1, 1969

Jan 1, 1969

By S. C. Das. Gupta, B. S. Lement

isothermal formation of martensite occurs in the range of —65o to —197oC and is always preceded by some athermal transformation. By rapid cooling the isothermal, but not the athermal, component of transformation can be suppressed. Stabilization against isothermal transformation can be induced by cycling from below M. to room temperature. A LTHOUGH the transformation of austenite to XV martensite is generally believed to occur only on cooling, recent evidence indicates that this reaction can also occur at constant temperature. Isothermal formation of martensite was observed in tool steel by Fletcher, Averbach, and Cohen.'. They found that the hardening reaction that occurs during the quenching of a plain carbon or low carbon alloy tool steel does not stop immediately when room temperature is reached; instead austenite continues S. C. DAS GUPTA is Research Fellow, Department of Metallurgy, University of Notre Dame, Notre Dame, Ind. B. S. LEMENT, Associate Member AIME, is on the Research Staff, Department of Metallurgy, Massachusetts Institute of Technology, Cambridge, Mass. Discussion on this paper, TP 3123E, may be sent, 2 copies, to AIME by Dec. 1, 1951. Manuscript, April 16, 1951. Detroit Meeting, October 1951. This paper represents part of a thesis by S. C. Das Gupta submitted in partial fulfillment of requirements for the degree of Doctor of Philosophy in Metallurgy to the University of Notre Dame. to transform at room temperature although at a decreasing rate. Since only a small amount of austenite transforms in this fashion, isothermal formation of martensite was considered to be merely a "tailing off" effect of the main hardening reaction. Another point of view was advanced by Kurd-jumov and Maksimova"' * who reported that the austenite-martensite reaction could be suppressed by rapid cooling of a 6 pct Mn-0.6 pct C steel in liquid nitrogen and that as much as 25 pct martensite could be formed by reheating to and holding at subzero temperatures above that of liquid nitrogen. These investigators came to the conclusion that martensite is thermally nucleated at certain special regions in the austenite and subsequently grows to observable dimensions. Isothermal transformation of austenite to martensite was cited by Fisher, Hollomon, and Turnbull" as evidence supporting another nucleation and growth theory of martensite formation. According

Jan 1, 1952

By R. K. Govila, E. H. Parkison

THE interplanar angles for hcp metals vary with c/a ratio, and therefore must be computed separately for each particular metal or alloy. Manual computation of these angles is laborious and time consuming, and for this reason computer programs have been developed to accomplish this task.1"3 However, these programs have certain disadvantages. For example, they require prior knowledge and understanding of ALGOL or FORTRAN languages. Further, they will not print out specific angles but instead give all angles between given limits—thus program2 prints out a total of 26,649 angles between planes with indices and in the range from (4 4 4) to (4 4 4) for any given c/a ratio. The purpose of this note is to present a simple and inexpensive computer program for accomplishing this task. This program is written in BASIC language4 which does not require any prior knowledge of computer programming, and is ideally suited for nonprofessional programmers. It also provides flexibility for the user by allowing him to select any indices for as many or few planes as desired for any given c/a ratio. The computer program proposed below is based on the relationship in which + is the angle between any two planes and . TO illustrate use of the program, consider the problem of calculating the interplanar an-

Jan 1, 1970

By H. Groeneveld, C. A. Connally, P. J. Hoenmans, J. J. Justen, W. L. Mason

A miscible displacement pilot using a slug of LPG driven by separator gas was conducted in the Cardiurn reservoir of the Pembina field. The injection pattern was a 10-acre, inverted, isolated five-spot. Upon completion of the LPG-gar phase, an experiment was conducted using a slug of water followed by gas. Calculated performance of the pilot is compared with actual performance. Equations are developed to calculate the distribution of LPG into zones of varying permeability, to estimate the progress of the flood at different times in the various zones and to estimate gas rates after breakthrough. The analysis indicates that permeability stratification was a dominant factor in controlling oil recovery and that oil was completely displaced from the swept pore volume. The results of the pilot indicated that miscible flooding is a practical means of pressure maintenance in this reservoir. The total recovery from the pilot area was good in spite of the early breakthrough of LPG. The effects of stratification were reduced by injecting a slug of water into the partially swept reservoir. INTRODUCTION The Pembina field,' located in Alberta, is the largest oil field in Canada and one of the largest in the North American continent. The reservoir is a stratigraphic trap producing from the Cardium sand. Neither bottom water nor free gas has been found. The recovery of oil by the natural depletion mechanism has been estimated at 12.5 per cent. Pressure maintenance studies of various areas have indicated that the recovery can be increased 21/2 times by water flooding, and a large area of the field is presently under water flood. However, reservoir studies of the North Pembina area indicated that miscible flooding might be competitive with water flooding. A pilot test was conducted to evaluate the performance of a miscible flood. A 10-acre, inverted, isolated, five-spot pattern was selected for the pilot. The pattern area was large enough to minimize wellbore fracturing effects and contained sufficient oil to provide significant working numbers. The performance of each of the four producers could be evaluated individually and compared. In the event of breakthrough in one direction, the effect would be isolated from the other producers. The use of a single injector minimized the volume of LPG required, and, because of the high mobility of gas, one well was sufficient to inject the necessary daily volume to replace the high rate of production. With four producers, the test could be completed in time for results to be evaluated, additional engineering studies to be made and a unit to be formed before the reservoir pressure in the North Pembina area declined below the bubble point. The pilot was located in an area developed on staggered, 80-acre spacing. The injection well was drilled at a regular location, while the four producers were drilled 467-ft north, east, south and west of the injector. Each quadrant and its associated producer were identified according to their direction from the injector— that is, north, east, south or west. The eight surrounding producers on 80-acre spacing were shut in to isolate the pilot area and provide for reservoir pressure observation. The pilot wells were completed using permanent-type completion techniques. After coring, casing was run through the pay section and cemented. Inside 51/2-in. casing, 2 1/2-in. tubing was hung. The wells were perforated opposite the Upper Cardium sand and lightly fractured. Fracturing volumes, rates and pressures were low to minimize the extent of the fractures. The fracturing treatments average 1,000 lb of 20-40 mesh sand in 700 gal of a low fluid-loss sand-carrying agent. Feed rates and wellhead fracturing pressures averaged 5.5 bbl/min at 2,535 psig, respectively. After fracturing, the productivity index was measured in each of the five pilot wells. The average PI of the four producers was 0.41 BOPD/psig drawdown. The measured PI'S were approximately the same as PI'S calculated from core analysis data, indicating that the fracturing treatments were just sufficient to overcome

CONTENTS PAGE FOGLER, M. F., and QUINN, E. J.-Scratch and Brinell Hardness of Severely Cold-rolled Metals. Discussed by H. S. Rawdon, Carl Benedicks, M. F. Fogler, A. L.Davis 1 GREEN, C. H. Eutectic Patterns in Metallic Alloys. Discussed by Carl Benedicks, Carle R. Hayward, G. E. Dalbey, George F. Comstock, C. H. Green. 3 ARCHER, ROBERT S., and JEFFRIES, ZAY.-New Developments in High-strength Aluminum Alloys. - Discussed by F. B. Coyle, M. F. Fogler, Zay. Jeffries, D. J. McAdam, Jr., Horace C. Knerr, Ernest Schweizer 6 FLICK, FULTON B.-Etching Aluminum and Its Alloys for Macroscopic and Microscopic Examination. Discussed by Samuel Daniels 22. MERICA, PAUL D., and WALTENBERG, R. G.-The Malleability of Nickel. Discussed by H. W. Gillett, Ancel St. John. L. W. McKeehan, A. L. Feild, A. L. Davis 23 ANDERSON, ROBERT J., and NORTON, JOHN T.-X-ray Evidence Versus the Amorphous-metal Hypothesis. Discussed by Zay Jeffries, Chu Phay Yap, Francis B. Foley, H. H. Lester, Edgar C. Bain, Ancel St. John, L. W. McKeehan, Carle R. Hayward, R. P: Heuer, Jerome Alexander, Carl Benedicks 26 COOK, MAURICE, and EVANS, ULICK R.-Recrystallization and Grain Growth in Soft Metals. Discussed by M. F. Fogler 36 POLUSHKIN, E. P.-Determination of Structural Composition of Alloys by a . Metallographic Planimeter. Discussed by H. S. Rawdon 36 BASSETT, WILLIAM H., and DAVIS, C. H.-Corrosion of Copper Alloys in Sea Water. Discussed by W. B. Price, W.. R. Webster, George A. Orrok, A. E. White, William H. Bassett, D. K. Crampton 38, Scratch and Brinell Hardness of Severely Cold-rolled Metals Discussion of the paper of M. F. FOGLER and E. J. QUINN, presented at the New York Meeting, February, 1925, and issued as Paper No. 1395-E with MINING AND METALLURGY, January, 1925. H. S. RAWDON, * Washington, D. C.-We had the privilege of looking over the data just given before they were published and we were not able to suggest any convincing reason for the differences that were secured

Jan 6, 1925

By H. H. Kellogg

A model of the slag-fuming process for recovery of zinc oxide fume from lead blast furnace slags, adapted to solution by a digital computer, is presented. The model incorporates the variaticm with time of the following: the fuming of zinc and lead, the change in the ferrous-ferric ratio in the slag, the transfer of sulfur to and from the slag, the temperature of the liquid slag, the temperature of the gases and fume which exit to the flue, the heat losses to the water jackets, and the amount of frozen slag on the water jackets. The assumptions which underlie the model-some of which are but crude approximations—are discussed. Despite some obvious shortcomings, the model simulates faithfully many of the important features of practical slag-fuming operations. The behavior of the model is compared with the operation of the American Smelting and Refining Co. fumzace at El Paso, Tex. The model is used to predict the effects on performance of changes in the coal rate, the temperature of the secondary air, and the composition of the coal. THE fuming of lead blast furnace slag for recovery of zinc oxide is standard practice today, and it has been the subject of several previous attempts at mathematical process analysis.'-' The mathematical process model described in this paper incorporates many of the features from the earlier studies, but it is a far more complete and realistic representation of the commercial process in that the following additional features have been included: the fuming of lead as well as zinc; the transfer of sulfur between slag and gas; the addition of slag feed in batches, over a period of time; tapping of the final slag over a period of time; the change of slag temperature with time. The additional features of the present model add greatly to the mathematical complexity, but this difficulty has been obviated by programming the model for solution by a digital computer. The IBM 7094 computer solves the model for one operating cycle of the fuming furnace in less than 1 min. It is doubtful if the same calculations could be completed with the aid of a desk calculator in less than a month. The computer program, written in the Fortran IV language, is too lengthy for presentation here.* Instead, this paper As shown in the sections which follow, it does simulate with remarkable faithfulness most of the known behavior of the industrial process. On the other hand, the model contains several gross simplifications of both the chemistry and heat balance, necessitated by the lack of more exact knowledge. In addition to these known weaknesses, it is not unlikely that those more intimately acquainted with industrial practice than the author will find other additions to or modifications of the model which will improve its utility and reliability. CHEMISTRY In brief outline, the present model treats the fuming furnace as two units, A and B, in series. In A the batch of slag reacts with the continuous stream of air (primary and secondary) and fuel injected at the tuyeres, to produce a stream of hot, reduced gases containing zinc vapor. The zinc content of both the slag and the product gas changes with time because of the batch nature of the process. Unit A is called the "lower furnace" in this paper; physically, it is considered to be that part of the fuming furnace which lies below the charge port. In B, the "upper furnace", the product gas from A is burned with the stream of "tertiary" air, to produce zinc oxide fume. The performance of B also depends on time because of the time dependence inherited from the product gas of A. The rate behavior in the lower furnace determines the important features of the process—the rate of elimination of zinc and lead from the slag, and the amount of fuel required for this purpose. Bell, Turner, and peters' published the first useful model of the lower furnace. They employed the assumption that, at any instant of time, the slag and reduced gas reach a state of equilibrium, according to the reactions: They cited only indirect evidence in support of their assumption of slag-gas equilibrium, yet several more recent laboratory studies of the activity of zinc oxide in slags4-8 have produced evidence which supports their view. On first acquaintance it seems unlikely that a high-output "rate" process like slag fuming would even approach an equilibrium state. The author, in an earlier study,' established, however, that the gas-slag interface in a fuming furnace was capable of such high mass-transfer rates that a close approach to equilibrium between gas and slag was quite probable. In devising the present model it was decided to assume a state of equilibrium between slag and gas at the outset, and then to modify this assumption as necessary in order to make the model agree with the be -havior of the actual process. Up to this time the assumption remains a part of the model, since no behavior

Jan 1, 1968

By L. A. Adorjan

The tensile strength of agglomerate models due to capillary forces has been determined by computation of the exact surface profiles. Graphs showing tensile strength as a function of moisture content and contact angle me given for spheres in cubic arrangement. Another model of cones attached to cube faces, in cubic packing, provides a better representation of angular particle agglomerates. An algebraic formula approximating tensile strength as dependent on surface tension, particle size, moisture content, contact and cone angles was developed. The phenomenon of "capillary evaporation" due to high negative capillary pressures is explained and its influence on tensile strength of agglomerates is evaluated.

Jan 1, 1977

The first record of coal anywhere in the Appalachian regions of which we now know is along the north fork of the Potomac River, above the mouth of Savage River, on a map entitled, A Plan of the upper Part of Potomack River call Cohongorooto Survey'd in the Year 1736. Benj. Winslow1 two "Cole-mines" are shown, one just above Green Island and the other just below Hopwood Run. Winslow was in charge of a surveying party to "Lay out the Bounds of the Northern Neck of Virginia," or Lord Fairfax's Grant, his party locating the liver above the mouth of the Shenandoah, while another party located it below that point, and then around Chesapeake Bay and up the Rappahannock River. The results of the two surveys were combined in a map called, The Courses of the Rivers Rappahannock and Potowmack, in Virginia, as surveyed according to Order in the Years 1736 & 1737, made by Wm. Mayo, which does not show the "cole-mines;" this map was used with the report of the boundary commission which was sent to London in the case before the Privy Council. The boundary line decided upon was surveyed on the ground in 1746, just ten years after the original one. The results of this work were shown on A Map of the Northern Neck in Virginia, According to an Actual Survey begun in the Year MDCCXXXVI, and ended in the Year MDCCXLVI, Drawn by Peter Jefferson And Robert Brooke, Surveyors, which is now in the Colonial Office in London. This map shows the "cole-mines" in the same location as on Winslow's map, and taken from his record, of course, as that part of the survey was not retraced. Faulkner, who examined all of these records in his review of the case in 1832, refers to the notes of the original survey as "No. 10. The original field notes of the survey of the Potomac River, and the mouth of the Shenandoah to the head spring of said Poto¬mac River, by Mr. Benjamin Winslow." While the notes of the 1746 survey are in the London records and photographic copies of them are in several libraries in this county, the notes of the 1736 survey cannot be found anywhere. (For Chas. J. Faulkner's report, dated Nov. 6, 1832, see Kercheval's History of the Valley of Virginia, pp. 160-173. Jas. W. Foster's Maps of the First Survey of the Potomac River, 1736-37, in Wm. and Mary College Quarterly History Mag., April, 1938, gives a complete history

Jan 1, 1942

By P. Marier, T. R. lngraham

The kinetics of the sulfation of MnO,, MnzO3, and Mn3O4 in SO,, SO3, and O, mixtures was examined and the descending order of sulfation rates at temperatures near 400°C was found to be Mn,O3 > MnO, > Mn3O4. The respective activation energies for the thermal decomposition of MnO, and Mn,O, are 39 and 47 kcal. At 900°C, the thernzal decomposition of MnSO, to MnzO3 is slower than that to Mn3O4. The respective activation energies are 62 and 51 kcal, respectitely. MANGANESE is used to improve the hot workability of steel in the proportions of approximately 13.5 Ib of ferromanganese per ton of steel produced. This requirement accounts for about 95 pct of its large industrial market in North America. The remaining 5 pct is used in the battery and chemical industries. In most North American ores, the percentage of manganese and the manganese-to-iron ratio are not suitable for the direct production of ferromanganese. Hence, most of the North American requirements for manganese are satisfied by importing ore. Typically, many of the studies done on native low-grade manganese resources have been directed toward the production of ore substittes" and the recovery of manganese from open-hearth slags.3 Of the wide variety of processes which have been proposed, the most popular involve compounds in the Mn-S-O system. The thermodynamic properties of manganese and its compounds were reviewed by ah' in 1960 and, more recently, lngrahams discussed the thermodynamics of some of the reactions involved in the Mn-S-O system at normal roasting temperatures. The conditions for producing manganese sulfide during the reduction roasting of manganese sulfate are discussed by Fuller and Edlund.9 A novel scheme was proposed recently by zimmerley7 for utilizing waste sulfur dioxide from stack gases to recover the manganese from ocean-mined manganese nodules. Very little of the work published on manganese compounds has been related to reaction rates. Singleton et 1.' studied the rates of reaction on the MnO-C and Mn7C3-3MnO systems and observed linear and parabolic kinetics respectively in the systems. Tatievskaya et a1.' studied the low-temperature reduction of Mn&, MnO,, and Mn& in HZ and CO, and reported activation energies in the range 1628 kcal. In this paper, the rates of some of the decomposition and formation reactions involving MnSO4, MnOz, MnzO3, and Mn3O4 will be examined after the conditions for the thermodynamic stability of the individual compounds have been designated. CONDITIONS FOR STABILITY OF MnSO4, MnOz, MnZO3, AND Mn3O4 The areas of stability for h'hSO4, MnOz, MnzO3, and h3O4 were established from the data of Mah4 and Ingrahams and are shown in the predominance area diagram,10 logpq- logpsq, in Fig. 1. The diagram is drawn for two temperatures, 700°K, solid lines, and 1100°K, dotted lines. The sketch for the lower temperature includes the conditions likely to prevail in the Zimmerley patent7 when manganese nodules react with sulfur dioxide and that for the higher temperature indicates the conditions for recovering MnzO3 or Mn3O4 from MnSO4 during a roasting reaction. From the fact that the boundary between the areas of stability of MnOz and hSO4 at 700°K is parallel to the abscissa, it is evident that MnOz and SO2 should react together to produce MnSO4, irrespective of the oxygen pressure in the system. If the source of sulfur for sulfation were from waste flue gases, it is likely that the oxygen content of the gas stream would be more than sufficient to oxidize any MnsO4 to MnzO3, 107 atm of O2 required, or even to convert any Mnz03 to MnOz, 0.02 atm OZ required, prior to sulfation. At 1100°K, the diagram indicates that MnSO4 may be converted directly to either MnzO3 of Mn3O4, depending upon the prevailing partial pressure of oxygen. When the gas stream contains more than 1 pct Oz, logpq = -2, only MnzO3 would be recovered from an experiment done under equilibrium conditions. At oxygen partial pressures of less than 1 pct, one would expect to bring about a reversible exchange between MnSO4 and Mn3O4 by appropriate adjustment of the partial pressure of SOZ. These various reactions will be described in the subsequent kinetic experiments.

Jan 1, 1969

By G. M. Ault, G. C. Deutsch

The paper reviews the efforts made to utilize powder metallurgy to solve problems encountered when using alloys at high temperatures. The following subjects are discussed: comparison of wrought and sintered super alloys, sintered aluminum powder, porous materials for transpiration cooling, molybdenum, and cermets. TODAY, powder-metallurgy techniques are be-JL coming increasingly important, producing materials which at the present time cannot be made by any other method. Among these materials are high melting-point metals such as tantalum and tungsten, porous metals for filters and lubricant-containing bearings, electrical contacts and electrodes (i.e., tungsten-copper), cutting tools of the cemented carbides, and magnet alloys. In addition, the powder-metallurgy industry has grown because, through the application of its methods, shaped parts, such as gears, can be produced at tremendous rates with a low scrap loss in comparison with manufacture by casting or forging and machining. In the past few years, by utilizing powder metallurgy, several approaches to the problem of high temperature materials have been investigated. In this paper the authors will review some of the studies on application of materials having properties above 1350°F. Since their experience lies in the aeronautical field, possible uses of powder-metallurgy techniques in the production of aircraft en- gines will be emphasized. A large portion of the work is classified, but such a restriction has not eliminated any field from discussion, although limiting the amount of detail it is possible to present. The development of high temperature alloys from powders and porous metals for cooling will be discussed as well as research done on molybdenum and molybdenum alloys, cermets, and intermetallics. Some studies on the utilization of cermets will be considered along with special problems that have been revealed through these investigations. Special interest in certain factors of sintered aluminum powder (SAP) makes it desirable to discuss this material although its use temperature is below the 1350°F limitation set for this paper. High Temperature Alloys from Powders In general, components made from powders for room-temperature application have been investigated with the primary purpose of taking advantage of the high production rates and economies made possible by powder metallurgy. From the standpoint of properties, the ojective of the powder metallurgist has been to obtain a product comparable to the cast or wrought product that is to be replaced. Comparisons of the properties of alloys made by powder-metallurgy methods with those of similar compositions made by casting and forging are reported in the literature.12 In many cases equivalent

Jan 1, 1955