Search Documents

By J. P. Newell, R. W. Storey

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120". This head design proved to be very satis-

Jan 1, 1953

By Gerald A. Munson, Fremont F. Clarke

DURING recent years the use of lithium has expanded greatly in industrial, chemical, and metallurgical fields, while at the same time modernized methods of mining and refining lithium have increased production. Technical literature includes many papers describing the geology and mineralogy of lithium deposits. Mining and beneficiating problems, however, have not been thoroughly described. Published reports have failed to emphasize that one of the chief reasons lithium minerals were not extensively mined until recently is the difficulty of beneficiation. Four lithium minerals of pegmatites and the lithium-sodium-phosphate byproduct from the brines at Searles Lake, Calif., have been sources of lithium. Among the pegmatite minerals, only spodu-mene and petaline are known to occur in deposits large enough to support large tonnage operations. Spodumene, a lithium-aluminum-silicate, is the principal lithium mineral mined in the U. S. Lithium Corp. of America, during its rapid development and growth, has successfully employed three different methods of concentration: 1) hand sorting, 2) Heavy Media separation, and 3) froth flotation. Each method, though economic in its sphere, is becoming outdated as extractive techniques improve. The most recent development has taken place at Lithium Corp.'s new operation in North Carolina, where the extractive process yields lithium compounds directly from mined rock without an intervening concentrating step. Until 1954 Lithium Corp. mined only in the southern part of the Black Hills of South Dakota, where the various types of lithium-bearing pegmatite could be used to develop untried processes of beneficiation. Concentrates from these operations are shipped to the corporation's chemical plant in St. Louis Park, Minn., where actual extraction of lithium and production of commercial compounds takes place. Nature of Deposits The geology of the southern Black Hills pegmatite deposits is admirably presented by a U. S. Geological Survey publication.' Only the factors pertinent to exploitation need be mentioned here. Lithium Corp. has been interested primarily in three deposits, the Edison, the Mateen, and the Longview-Beecher No. 2. The history of these deposits dates back to the mining boom of 1880 to 1900 in the Black Hills, when most of the deposits were prospected for tin by the ill-fated Harney Peak Tin Mining Co. The three deposits described here, however, lay idle and unwanted until Lithium Corp. opened the Edison mine in 1943 and the Mateen and Longview-Beecher No. 2 in 1951. Edison Deposit: The Edison deposit is about a mile southeast of Keystone, S. D., on the northeastern flank of the Harney Peak uplift. The deposit consists of no less than four and probably at least six separate pegmatites that coalesce in a central mass from which the individual pegmatites finger outward and downward in complexly folded schist and gneiss beds of the country rock.

Jan 1, 1956

By P. K. Foh, C. G. Dunn

IN an investigation of the rolling and recrystalliz-ing textures obtained from single crystals of Si-Fe, Koh and Dunn included specimens in the (111) [lie] orientation.1,2 This note reports some additional results obtained on samples of this orientation set aside for further study. After, primary recrystallization longer annealing treatments at 980°C produced only normal grain growth; after 16 hr at 980°C the largest grains were approximately 0.010 to 0.020 in. in diam. The orientations of 13 of the larger grains were found by the transmission Laue method. The unidentified (110) poles of these grains have been added to the (110) pole figure obtained after primary recrystallization2 to give the plot shown in Fig. 1. When grain identifications are also included, such a plot reveals the following. Two orientations agree almost exactly with the peak pole ,density positions of component B of the primary recrystallization texture, one with component A, and one with component C. All the remaining orientations except one have (110) poles near weaker and unidentified pole density peaks. In fact, the correlation is good enough for an identification of eight components. Previously only components A, B, and C were certain. The results are perhaps even more informative when combined with the (110) pole figure of the cold-rolled crystal to give the plot shown in Fig. 2. Each of the 13 orientations is identified and uniquely determined by selecting two (110) poles per crystal, which are 90" apart. The plot shows that every grain of the 13, except grain 6, has a (110) pole in common with a (110) pole concentration of the cold-rolled crystal. The orientation relationship with the cold-rolled orientation may be expressed as approximately 25" rotations about <110> axes, which is in agreement with the results found for coarse-grained primary recrystallization.2 If primary recrystallization had occurred according to the <110> rule without preference, there would have been 12 components. Actually our limited data reveals nine of the possible 12. The integrated pole figure also shows preferences among them, since three are considerably stronger than the rest. In addition to the above direct information, the following conclusions may be drawn. Primary recrystallization of the (111) [110] cold-rolled crystal produces a limited number of weak and strong components with the larger than average primary grains from these components related to the cold-rolled crystal by 25° <110> relationships. In arriving at this conclusion of limited orientations the (111) [110] orientation has to be ruled out as a source of large primaries for two reasons. First, growth in this orientation was not observed, despite an expected high grain boundary mobility (due to its 25" <110> relationship with every component of the texture). Secondly, primary recrystallization usually produces grains in new orientations, particularly in a single orientation matrix; but (111) [110] is not new. Other orientations besides those of the <110> type may be considered unlikely, of course, because the <110> relationship holds quite well for primary recrystallization2 and should produce the large primaries. There are exceptions to this rule, but probably not enough to provide large

Jan 1, 1958

By A. A. Burr, D. Caplan

IN carrying out experiments in metal-gas systems, it is often difficult to estimate how long a reaction period must be allowed for equilibration. This is especially true in systems for which the diffusion coefficient is not known. In an investigation of the Cr-O system, the necessary information was obtained in the way described subsequently. Two pieces of chromium sheet of different thicknesses were packed in mixed powders of chromium and Cr2O3 and sealed into an evacuated metal capsule by welding. Austenitic stainless steel proved suitable as a capsule material up to 1350°C and molybdenum at higher temperatures. The capsule then was heated at a specific temperature for a time sufficient to saturate with oxygen the thinner but not the thicker specimen. The time is readily estimated from a preliminary experiment if a sufficient thickness differential is chosen. Under these experimental conditions, the metal sheet is exposed to a partial pressure of oxygen equal to that of the dissociation pressure of the oxide and hence can become saturated with oxygen without developing any second phase. After cooling, both samples were analyzed for oxygen by the vacuum fusion technique. Assuming that the surface of the specimens is kept saturated with oxygen throughout the experiment, the diffusivity can be calculated by application of the appropriate solution to Fick&apos;s second law. This is most conveniently accomplished by use of a plot of mean fractional saturation (Cm-Co) / (Cs-Co) vs (Dt) ½/L as given by Darken,&apos; where t is time, L the half-thickness of the sheet, and D the diffusion coefficient. Cm, the mean concentration at time t, is given by the oxygen percentage in the thicker specimen; Cs, the constant surface concentration, is the oxygen percentage in the thinner specimen; Co is the oxygen content of the original chromium sheet. (Cm-Co) / (Cs-Co) is calculated and the corresponding (Dt) ½/L is read from the graph and D thereby calculated. By performing the experiment at two temperatures and plotting log D vs 1/T, the D for any temperature is established. (The activation energy for diffusion may be obtained from the slope of the line.) Once D is known as a function of temperature, it is a simple matter to estimate the correct reaction time for experiments with single specimens at other temperatures by equating (Dt) ½/L to its value for effective saturation. Darken&apos; points out that this is approximately unity. The solubility of oxygen in chromium, as determined from the thin samples at each temperature, proved to be approximately 0.03 pct at 1350°C and less at lower temperatures. Due to low solubility and to the known difficulties of the vacuum fusion method in this low range, the values obtained for D (5x10-0 sq cm per sec at 1350°C) are estimated to be correct only within an order of magnitude. Nevertheless, the method has proved useful in estimating reaction times. Its usefulness will be greater in metal-gas systems where the solubility is appreciable. A second function of the method is to permit the determination of diffusion coefficients in systems for which the conventional techniques are experimentally difficult or impossible.

Jan 1, 1956

By L. Bombardieri, H. F. Mills

IRON KING mine, producing gold-silver-lead-zinc ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pattern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length. with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth. the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 51/2 -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material To secure a cheap source of waste fill for stoping operations, a block cave area was undercut In the hanging wall near the north end of the mine above the 600 level. Waste from the block cave is drawn from any of three large drawpoints on the 600 level, and a series of hanging wall transfer raises with controls and bypasses on each level provide a fast low-cost material for fill. The block cave is worked vertically through to surface in the form of a steep-sided hole 350x250 ft and several hundred feet deep, the sides of which cave and provide fill material without any blasting. Fill is a mixture of caliche-cemented surface gravel and small particles of hanging wall schist. Level Development: An orebody 300 times as long as it is wide requires a lot of development work. Former practice consisted of driving a haulage drift about 30 ft from the ore in an andesitic footwall, a drift on the ore, and crosscuts from the haulage drift at 100-ft intervals. Crosscuts are about 90 ft long. At present, only the odd numbered levels are so developed, and on the even numbered levels only the haulage drift and crosscuts are driven. Little or no timber is used for this development. This change resulted in 20 pct reduction of development costs and 50 pet reduction of square set stoping required for removal of floor pillars. Elimination of ore drifts on alternate levels leaves

Jan 1, 1957

By H. R. Nelson, Martin S. Maier

The diffusion of metals plays an important role in many metallurgical processes,lJ as, for example, the formation of alloys by the annealing of mixed powders, the homogenization of segregated alloys, and the carburization of steel. Other equally important phenomena, such as recrystalli-zation and creep, are based on the movement of like atoms. Although much is known concerning the effects of diffusion in metals, very little is known concerning the details of the physical processes involved. 1,3-5 The data that should give most information concerning the processes involved in diffusion are those on the diffusion of like atoms—self-diffusion. Very little is known concerning the rates of self-diffusion of metals because before the discovery of artificial radioactivity in 1934 there was no means of detecting the movement of the diffusing atoms through the solvent metal except in the elements possessing natural radioactive isotopes—lead, thallium and bismuth. Using the induced radioactivity of the element as an indicator, atoms can now be "tagged" so that the rate of diffusion of the radioactive isotopes of an element (tagged atoms) into the stable isotopes of the same element can be measured. As the radioactive and stable isotopes of an element differ only in nuclear structure, it is quite certain that all isotopes of an element diffuse at the same rate. Two techniques have been used to measure self-diffusion. In one, a thin layer of radioactive metal is deposited on the face of the solvent metal, and the decrease in the surface activity as the radioactive atoms diffuse into the solvent metal is measured. This method has been used to determine the coefficients of self-diffusion of lead6-l0 and bismuth10 using natural radioactive isotopes, and of gold1&apos; and copper12 using artificial radioactive isotopes. In the other technique a thin layer of the radioactive metal is deposited oil one face of the solvent metal, and after diffusion has occurred the specimen is cut in thin sections to obtain the concentration-penetration curve. This method has been used to determine the coefficients of self-diffusion of gold,13 zinc,14-l6 silver," and copper.17 The second method was used for the work described in this paper. Materials The coefficients of self-diffusion were determined in two grades of polycrystalline copper and in single crystals of copper. Commercial OFHC copper was used in the form of disks I in. in diameter by % in. thick. Samples of high-purity copper described by Phillips and Skinnerl9 were supplied through the courtesy of the American Smelting and Refining Co. The high-purity copper rod was used without remelting by cross-rolling to a thickness of 0.075 in., from which disks 7/8 in. in diameter were cut. A good grade of bus-bar copper was used to make the single crystals.

Jan 1, 1942

By J. W. Stewart

THE aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula. Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I), It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the I5 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year. PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1941

By Martin S. Maier, H. R. Nelson

The diffusion of metals plays an important role in many metallurgical processes,lJ as, for example, the formation of alloys by the annealing of mixed powders, the homogenization of segregated alloys, and the carburization of steel. Other equally important phenomena, such as recrystalli-zation and creep, are based on the movement of like atoms. Although much is known concerning the effects of diffusion in metals, very little is known concerning the details of the physical processes involved. 1,3-5 The data that should give most information concerning the processes involved in diffusion are those on the diffusion of like atoms—self-diffusion. Very little is known concerning the rates of self-diffusion of metals because before the discovery of artificial radioactivity in 1934 there was no means of detecting the movement of the diffusing atoms through the solvent metal except in the elements possessing natural radioactive isotopes—lead, thallium and bismuth. Using the induced radioactivity of the element as an indicator, atoms can now be "tagged" so that the rate of diffusion of the radioactive isotopes of an element (tagged atoms) into the stable isotopes of the same element can be measured. As the radioactive and stable isotopes of an element differ only in nuclear structure, it is quite certain that all isotopes of an element diffuse at the same rate. Two techniques have been used to measure self-diffusion. In one, a thin layer of radioactive metal is deposited on the face of the solvent metal, and the decrease in the surface activity as the radioactive atoms diffuse into the solvent metal is measured. This method has been used to determine the coefficients of self-diffusion of lead6-l0 and bismuth10 using natural radioactive isotopes, and of gold1&apos; and copper12 using artificial radioactive isotopes. In the other technique a thin layer of the radioactive metal is deposited oil one face of the solvent metal, and after diffusion has occurred the specimen is cut in thin sections to obtain the concentration-penetration curve. This method has been used to determine the coefficients of self-diffusion of gold,13 zinc,14-l6 silver," and copper.17 The second method was used for the work described in this paper. Materials The coefficients of self-diffusion were determined in two grades of polycrystalline copper and in single crystals of copper. Commercial OFHC copper was used in the form of disks I in. in diameter by % in. thick. Samples of high-purity copper described by Phillips and Skinnerl9 were supplied through the courtesy of the American Smelting and Refining Co. The high-purity copper rod was used without remelting by cross-rolling to a thickness of 0.075 in., from which disks 7/8 in. in diameter were cut. A good grade of bus-bar copper was used to make the single crystals.

Jan 1, 1942

By J. J. Jakosky

The strategic importance of the metallic minerals in our industrial economy, and the declining rates of discovery have focused attention on means of exploration for new mineral deposits. A consideration of exploration techniques leads to an attempt to evaluate the effectiveness of geophysics as a tool for mining exploration. One means of evaluation will be to compare the use of geophysics in petroleum exploration with its possible uses in mining. Geophysics in Petroleum Exploration During the past twenty years, the petroleum industry has established an effective exploration technique. Geology is the basic tool in those areas where reliable predictions can be made from surface conditions. In the other areas, where the geological studies are inadequate, they must be supplemented with geophysics or direct exploration, such as drilling. Since geophysical work is far less costly than any form of direct explbration, it is used almost exclusively as the means for obtaining the desired subsurface information. The geological and geophysical techniques are credited with locating sites which yielded one producer for three dry holes during the year 1947.&apos; For the wells located without geology or geophysics, there is a ratio of one producing well to sixteen dry holes. From these figures it is seen that the geological and geophysical techniques are more than four times as successful as the nontechnical exploration. It will be in order to consider further this ratio of one producer to three dry holes. The geophysical methods in use today† do not pretend to locate oil directly; their function is to locate anomalies or structures favorable for the accumulation of oil. For a producing oil well we must have not only structure, but also other favorable conditions, namely: petroliferous source beds, the required porosity and permeability in the reservoir rocks, an impermeable cap rock over the reser- voir, and the necessary water or gravity drive to force the oil into the bore hole. Since the geophysical work can only detect and sometimes delimit the anomaly, these other necessary conditions can be determined only by direct exploration. The success of modern geophysical work in locating and limiting the structure itself is remarkably high, probably over 95 pct accurate. Geophysical work renders an important service in the delineation of the structurally unfavorable areas and their elimination from the drilling phase of the exploration program. When attempting to locate any material of scarce occurrence in the earth, it is of paramount importance to know where not to dig. This elimination of barren areas is the least appreciated but is of great economic importance. For illustration, the difference between one producer to three dry holes, and one producer to sixteen dry holes, represents a saving of thirteen drilled wells, which would require an expenditure many times the cost of the geophysical work that might have revealed the nonfavorable structural conditions. The percentage of geophysically-located wells necessarily will continue to increase in the statistics of future years, as the search for oil is extended

Jan 1, 1950

R,. P. JaRvis,* El Oro, Estado de México, México.—The practical problem raised by Mr. Wisser—that is, the determination of the lower limit of ore deposition, below which it is useless to look for ore shoots—is one of the most important in economic geology. He asks: "Can we learn to determine the position of such a line?" For individual districts, yes; but its determination has always been by empirical methods; that is by actually exploring the veins to such depths that the values drop below the economic limits. Usually the signs are plain enough that values have been bottomed without confirmation by the chemist or assayer. Most veins, when approaching their limit, begin to split into branches or stringers; the vein matter itself undergoes a change from "lively looking" rock to one that is dull and unpromising, the quartz, instead of having segregated into clean vein matter, has simply spread itself into the country rock, rendering this more siliceous but no richer—these, together with inclusions of the country rock in the vein, are all positive indications of the limit. Mr. Wisser seems disposed not to accept the law of cause and effect, which he calls "empiricism." He says: "Empiricism embodies an assumption perhaps not evident at first glance. It is this: that like effects spring from like causes and therefore necessarily have a common meaning." There can be no doubt as to the validity of this law, since it is the foundation stone upon which are built all inductive sciences, including economic geology. When demonstrable, proved facts become confused with inferences, as they seem to be generally in the paper under examination, no sound conclusions can be reached. Mr. Wisser has failed to give sufficient data covering the two vein systems which he cites as examples. Presumably they are situated in the Pachuca District of Mexico, but not everybody is familiar with the vein systems there in spite of the fact that it is world famous as a silver producer. Are these two systems separated some distance horizontally from one another and how far? He has given no estimate of the amount and kind of rock that has been eroded from over the present veins. His description of the two systems appears on page 100, beginning: "1. East-west veins," and ends on page 101, "they would lack spaces there in which to deposit." On page 101, with the paragraph beginning "On the other hand," he gives a picture of what he believes takes place in class 2 veins. The sum of this seems to be, according to Mr. Wisser&apos;s observations, that, in the east-west veins, class 1, there has been an invasion of an "altering solution," which I judge has been responsible for the formation of extensive "alteration haloes"; that these alteration solutions have followed along pre-existing fractures or fissures; and that after these alteration solutions finished their work the mineralizing solutions deposited the vein matter and metallic values. Mr. Wisser does not specify clearly what the "alteration haloes" consist of; in other words, what change the original rock has suffered, whether oxidizing, carbonating, or sulphidizing. If they came from depth they could not be oxidizing or carbonating, and in this case it is a bit

Jan 1, 1941

R,. P. JaRvis,* El Oro, Estado de México, México.—The practical problem raised by Mr. Wisser—that is, the determination of the lower limit of ore deposition, below which it is useless to look for ore shoots—is one of the most important in economic geology. He asks: "Can we learn to determine the position of such a line?" For individual districts, yes; but its determination has always been by empirical methods; that is by actually exploring the veins to such depths that the values drop below the economic limits. Usually the signs are plain enough that values have been bottomed without confirmation by the chemist or assayer. Most veins, when approaching their limit, begin to split into branches or stringers; the vein matter itself undergoes a change from "lively looking" rock to one that is dull and unpromising, the quartz, instead of having segregated into clean vein matter, has simply spread itself into the country rock, rendering this more siliceous but no richer—these, together with inclusions of the country rock in the vein, are all positive indications of the limit. Mr. Wisser seems disposed not to accept the law of cause and effect, which he calls "empiricism." He says: "Empiricism embodies an assumption perhaps not evident at first glance. It is this: that like effects spring from like causes and therefore necessarily have a common meaning." There can be no doubt as to the validity of this law, since it is the foundation stone upon which are built all inductive sciences, including economic geology. When demonstrable, proved facts become confused with inferences, as they seem to be generally in the paper under examination, no sound conclusions can be reached. Mr. Wisser has failed to give sufficient data covering the two vein systems which he cites as examples. Presumably they are situated in the Pachuca District of Mexico, but not everybody is familiar with the vein systems there in spite of the fact that it is world famous as a silver producer. Are these two systems separated some distance horizontally from one another and how far? He has given no estimate of the amount and kind of rock that has been eroded from over the present veins. His description of the two systems appears on page 100, beginning: "1. East-west veins," and ends on page 101, "they would lack spaces there in which to deposit." On page 101, with the paragraph beginning "On the other hand," he gives a picture of what he believes takes place in class 2 veins. The sum of this seems to be, according to Mr. Wisser&apos;s observations, that, in the east-west veins, class 1, there has been an invasion of an "altering solution," which I judge has been responsible for the formation of extensive "alteration haloes"; that these alteration solutions have followed along pre-existing fractures or fissures; and that after these alteration solutions finished their work the mineralizing solutions deposited the vein matter and metallic values. Mr. Wisser does not specify clearly what the "alteration haloes" consist of; in other words, what change the original rock has suffered, whether oxidizing, carbonating, or sulphidizing. If they came from depth they could not be oxidizing or carbonating, and in this case it is a bit

Jan 1, 1941

• "This country eventually may have to rely on foreign sources for some metals, not because it does not have them here but because it may have difficulty getting the labor to mine them. Few people realize the extent to which the &apos;old timers&apos; are still the backlog of the important districts." --Fred Searls, Jr. • A new filter has been developed by Arthur D. Little, Inc., for the ABC which will remove all dust from the air. Submicroscopic asbestos fibers are used as filter media and are claimed to stop all dust and pollen while passing suitable quantities of air. •Out in front public relationswise is the Peabody Coal Co. which has launched a 15-min television news program on WNBQ at 10:30 C.S.T., Tuesday and Thursday nights. Clifton Utley, news commentator, will tell how coal is mined today and indicate, with pictures, the improvement in efficiency and safety which has resulted from today&apos;s mechanized operations. •Two hundred coal mining companies are using roof bolts as a means of supporting about 14 million sq ft of roof surface, Edward Thomas of the Bureau of Mines reported. Various types of metal and wooden pins can be used. The method was first used by the St. Joseph Lead Co. over 20 years ago, but is now being studied and adopted widely in metal, nonmetallic, and coal mines. * The first ten technical graduates have reported at Hanford Works in the state of Washington, to begin the newly installed General Electric rotational training program, believed to be the first of its kind at any U.S. atomic energy plant. The program is to provide suitably trained personnel for the nation&apos;s atomic energy program. •The need for top-notch scientists and engineers to stimulate mining programs in British colonies is acute. About 60 American experts are being sought for the ECA sponsored program. Positions for mining engineers, geologists, assayers, topographers, and petrologists are open. •Production of primary aluminum for the first quarter of 1950 was 322,4250008 lb which is 6 1/2 million lb more than was produced in the first quarter of 1949. Shipments of aluminum sheet, plate, and strip amounted to 259.772,1571b for the first quarter. •Policy on manganese procurement for the stockpile is being studied by a House Armed Services Subcommittee with the possibility of lowering specifications. The U. S. Bureau of Mines is drafting a bill to encourage domestic production for stockpiling through producer subsidies. &apos;It will have to be cleared by the Bureau of the Budget and other agencies before going to Congress. •Oil men consider dry holes a necessary evil in their search for oil. Last year 34 out of every 100 wells drilled were dry holes. Yet Texas Technological College is attempting to drill a dry hole on its campus at Lubbock, taking every precaution to make sure it is a "duster" so its petroleum engineering students can play around with experiments without being bothered by any messy crude oil. --Natural Resources Notes. •A portable alertness indicator which signals lethargy in persons doing monotonous jobs has been developed for the Navy&apos;s Special Devices Center. A possible application to hoistmen is indicated but broaching the matter to them would be tricky.

Jan 6, 1950

By G. S. Hume

Activity in geological exploration and drilling continued in Canada in 1945 at about the same rate as in the previous year, but with disappointing results as far as new production is .concerned. Both in the foothills and on the Plains of Alberta, however, there are wildcat wells that have either given encouraging shows or some production, which are very important in relation to future developments. The normal decline of Turner Valley, the largest producing field in Canada, has continued, and this decrease has not been offset by new discoveries. In addition, the closing of the Canol pipe line on March 31, 1945, isolated the Norman Wells field in the Mackenzie River valley, and the outlet at present. is confined to supplying the relatively small local requirements. This

Jan 1, 1946

By J. T. Norton, N. J. Grant, A. R. Chaudhuri

MOST of the recent work to establish the mech-anism of creep in metals at high temperatures has utilized aluminum as the experimental material. It was thought desirable to initiate an investigation of a hexagonal close-packed metal, because of the relatively simple slip system, and compare the observed deformation characteristics with those that have been observed for the face-centerd cubic metals. High-purity magnesium was chosen for this purpose, first, because its strength and other mechanical properties are similar to those of aluminum in the same temperature range, and second, because the existing equipment was ideally suited to observe magnesium during creep. It is proposed in this paper to present a pictorial and qualitative account of the changes that high-purity magnesium undergoes during creep at 500°F. The characteristics of deformation of aluminum described below have been observed by various workers and accounts of these may be obtained from the papers of Chang and Grant.&apos;- These characteristics are: slip, subgrain formation, grain boundary sliding and migration, fold formation, deformation bands, and kink bands. It is well known that in a flat magnesium specimen, slip on the basal plane (0001) in the [1120] direction results in the formation of straight bands on the surface of the specimen. Schmid and co-workers&apos; have shown that this system is operative in the temperature range of -185" to 300°C (-300° to 572°F). They have also shown that a second system, slip on the pyramidal planes {1071} or {1012} in the [1120] direction, is operative at temperatures higher than 225°C (437°F). Between 225° and 300°C (437" to 572°F), therefore, deformation by both these systems is expected. Bakarian and Mathewson5 confirmed the occurrence of pyramidal slip on the {1011} plane and found that it resulted in irregular markings on the surfaces of their specimens. Burke and Hibbard6 obtained evidence of pyramidal slip in single crystals of magnesium deformed at room temperature. Bakarian and Mathewson5 suggested that the irregular appearance of these bands was due to slip on both of the pyramidal planes occurring simultaneously but in the same direction, the close angular relationship between the planes making this process possible. Furthermore, since neither of these planes is close enough to the basal plane, slip on the latter does not exhibit the irregular appearance of slip bands resulting from pyramidal slip. Experimental Procedure High-purity magnesium, supplied by the Dow Chemical Co., was used in these experiments. The analysis was as follows: Al, 0.0002 pct; Mn, 0.0018; Fe, 0.0024; Cu, 0.0002; Sn, 0.001; Ca, 0.01; Ni, 0.0003; Zn, 0.01; Pb, 0.0005; Si, 0.001; and Mg, 99.972. The magnesium was supplied in the form of 1/2 in. diam rods. The specimens had an overall length of 21/4 in., the round ends being threaded to fit the specimen holders. The previously round 3/16 in. diam gage section of the specimen had two parallel flats machined on opposite sides for microscopic observation, yielding a test zone having the dimensions of lx3/16x7/64 in. The specimens were electrolytically polished (without prior mechanical polishing of the machined flats), in a solution composed of 375 ml of ortho-phosphoric acid and 625 ml of ethyl alcohol.&apos; The cathode was a stainless steel sheet bent so that the specimen was completely surrounded. The voltage for successful polishing was 1.5 v at 100 to 300 milli-amp current. Electropolishing for about 45 min sufficed to obtain a good metallographic surface on the specimens after they had been machined. The creep tests were performed under constant load, and two types of equipment were used. In the first, designed by Servi and Grant,V he specimens were beam-loaded, and a furnace could be lowered to surround the specimen. As the microstructural changes could not be observed during the course of the test, the tests had to be interrupted periodically by removing the specimen for microscopic examination. The second unit was a high temperature microscopy furnace designed by Chang and Grant.&apos; The furnace was fitted with an optically flat quartz window having area dimensions 1.25x0.5 in., so that the whole test portion could be viewed through it at magnifications up to x240. The metallurgical microscope had three mutually perpendicular axes of motion, and, in addition, it was possible to measure angular displacements by rotation of the eyepiece. It was thus possible to make precise observations of the specimen during creep, and micrographs could be taken by attaching a camera to the eyepiece of the microscope. The average grain size of the specimens that were tested was about 1 to 3 mm. This grain size could

Jan 1, 1954

By Stanley L. Lopata, Eric B. Kula

SEVERAL methods are available for determining pole figures by X-ray means.&apos; The earlier film methods have been replaced by techniques in which the intensities are measured by Geiger counters on an X-ray diffractometerZm7. These methods utilize either flat transmission or reflection samples,214°8 cylindrical specimens,3 or spherical specimens.7 A single transmission or reflection sample will not yield information over the complete pole figure. The cylindrical specimens suggested by Nortod and the spherical specimen of Jetter and Borie7 have the advantage of allowing the whole pole figure to be obtained without any corrections to the intensity for absorption, There is a lower limit to the size of sheet which can be conveniently studied, however, and sample preparation can be rather tedious. Probably the most common method today for determining the complete pole figure is that developed by Schulz. A flat reflection sample is used for determining the pole figure from the center out to about 70". Because of the geometry of the system used, little or no correction for absorption or irradiated volume is necessary.4&apos;6 A separate transmission sample is used for the region near the edge of the pole figure. This procedure requires two separate samples, one of which must be a thin carefully-prepared transmission sample. Furthermore, since the reflection and transmission data are in different arbitrary intensity units, a region of overlap must be obtained, and the intensity data from one set of measurements converted to units of the other. These are serious disadvantages of this method, and they point out the need for a simplified procedure. Since the reflection technique can be used for planes whose normals lie up to about 70° from the sample surface normal, it is apparent that a complete pole figure can be obtained by reflection alone if sample surfaces are cut at oblique angles to the rolling plane Specifically, if a rolled sample is cut so that the normal to the surface formed lies equidistant (54" 44&apos;) from the rolling plane normal, rolling direction, and transverse direction, then complete information for one quadrant of the pole figure can be obtained by reflection from the surface. Fig. 1 shows this oblique surface, as well as the position of the pole of this surface in the pole figure. When a surface has been cut oblique to the rolling plane, the standard polar stereographic net is inconvenient to use, and it would be more desirable to have the center of the net coincide with the pole of the oblique plane. Fig. 2 shows such a net, where the center has been offset 54&apos; 44&apos; to correspond to a specimen cut as in Fig. 1. This net was in effect obtained by rotating a standard polar stereographic net 54" 44&apos; with the help of a Wulff net. With the experimental setup used. a sample can be cut from plate of 1/2-in. thickness or br Gen- erally thinner sheet is under investigation, and a composite specimen must be used. A convenient procedure has been to bond together, using epoxy resin, sufficient sheets to form a cube. These are clamped in a vise, and when dry, the whole vise is rotated and a flat surface ground at the required angle. The sample is then mounted inside a larger steel ring using Koldmount, the backside ground flat and parallel to the approximate desired thickness. The sample is then polished and etched to remove any effects of cold working during grinding. With this method only one quadrant of the pole figure is obtained. Often pole figures show symmetry around the rolling and transverse directions, and any slight asymmetry is due to scatter. Should the pole figure not be symmetrical, four oblique surfaces, corresponding to the four quadrants of the pole figure, would have to be examined. In most cases there is symmetry at least around the rolling direction, which reduces to two the number of quadrants to be investigated. For many purposes all that is required is an average polefigure for the four quadrants. This canreadilybe obtained with composite specimens of sheet material, where sheets Corresponding to each of the four quadrants can be intermixed. The four quadrants can be obtained by considering sheet in the normal position, and by rotatiolls of 180" around the sheet normal, the rolling direction, and the transverse direction. If desired, the whole thickness of the sheet can be used, yielding an average of the surface and interior textures; or the surface material can be removed from each sheet, resulting in a pole figure for the center alone. Eugene S. Meieran of the Massachusetts Institute of Technology has independently developed the same method. His results, adapted to a pole figure goniometer with a specimen spiraler, will be described in another publication.

Jan 1, 1962

By William B. Heroy

LOOKING back over the industrial and commercial progress of the United States during the last half century the outstanding influence has been the growth of the use of the fluid fuels, petroleum and natural gas. At the turn of the century these fuels supplied only 8 per cent of the energy requirements of the nation. Last year nearly 45 per cent of our heat and power supply were derived from these fuels. These figures are merely statistical reflections of the fundamental change in our national economy which has affected, in so many amazing ways, the life of this generation. The factors which have caused this change are still operative. The trend which has thus been established still continues and growth in the use of these fuels is, in all probability, still well below the peak, both for this country and for other parts of the world. Two great wars have not essentially changed this basic trend; if anything they have served to accelerate it. World War II did not alone increase our requirements for liquid fuels; it demonstrated the absolute essentially of petroleum resources to our national security. Petroleum is no longer just an important factor in our national standard of living; it is the most important single element in our national defence-

Jan 1, 1946

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By James T. Wood

Stratigraphy, structure and closure of the Paloma field are discussed, with some details regarding the present state of development. The Paloma anticline, a large dome modified by faults, is the largest single closed dome in the southern San Joaquin valley without surface outcrop or topographic expression. It owes its discovery to geophysics. Of nine wells drilled to the Stevens sand, seven are productive. The ultimate productive area may approximate 3000 acres when the limits of the field are determined. Introduction The Paloma field derives its name from the Paloma school, ½ mile north of what is now the center of the field. The field is 17 miles southwest of Bakers-field, in the south central part of the San Joaquin Valley (Fig. I). The present developed area and its expected extensions are in townships 31 and 32S., R.26E. It is the most southerly of several fields that produce from the Stevens sand zone. The first well to produce condensate was a joint test drilled by the Western Gulf Oil Co. and The Texas Co. near the center of sec. 3, T.32S., R.26E., well No. 54-3. This well was completed on Aug. 31, 1939, at a depth of 10,178 ft. The initial production was 2280 bbl. a day of condensate and 14,750,000 cu. ft. of gas (½-hr. gauge) through a ?-in. bean. Prior to the drilling of this well, the Ohio Oil Co. discovered and developed a small gas field, which embraces a part of three townships about their common corner but lies chiefly in secs. 31 and 32, T.31S., R.26E. The first well was completed on July I, 1934, at a plugged depth of 5239 ft. after having been drilled to 7957 ft, production was found in a 59-ft. zone IIO ft. below the Fourth Mya bed, within the Sari Joaquin clays. Until recently this field was known as the Buena Vista gas field. It is now carried by the Division of Oil and Gas as the Paloma gas field. Production within the Paloma gas field is derived from six wells, producing from several different zones in the interval from 4177 to 5548 feet. Geology Stratigraphy The sediments penetrated by wells in the Paloma held range in age from Recent to Upper Miocene. The entire section, which exceeds 10,000 ft. in thickness, conforms generally to the standard section of the south central San Joaquin Valley. The producing zone, sometimes called the Paloma sand, is the approximate equivalent of the Stevens sand zone of the Ten Section, Canal, Coles Levee and other fields. The stratigraphic section is shown in Table I. Paloma Producing Zone* (Stevens Sand Zone, Upper Miocene) .-The Paloma producing zone (Fig. 2), frequently referred to as the Paloma sand, is encountered at depths ranging from 9950 to 10,300 ft. In general, it is a massive, firm to hard, not too well sorted, fine to medium fine sand. It is interbedded with thin, hard, calcareous sand shells of similar texture and cherty

Jan 1, 1942

By James T. Wood

Stratigraphy, structure and closure of the Paloma field are discussed, with some details regarding the present state of development. The Paloma anticline, a large dome modified by faults, is the largest single closed dome in the southern San Joaquin valley without surface outcrop or topographic expression. It owes its discovery to geophysics. Of nine wells drilled to the Stevens sand, seven are productive. The ultimate productive area may approximate 3000 acres when the limits of the field are determined. Introduction The Paloma field derives its name from the Paloma school, ½ mile north of what is now the center of the field. The field is 17 miles southwest of Bakers-field, in the south central part of the San Joaquin Valley (Fig. I). The present developed area and its expected extensions are in townships 31 and 32S., R.26E. It is the most southerly of several fields that produce from the Stevens sand zone. The first well to produce condensate was a joint test drilled by the Western Gulf Oil Co. and The Texas Co. near the center of sec. 3, T.32S., R.26E., well No. 54-3. This well was completed on Aug. 31, 1939, at a depth of 10,178 ft. The initial production was 2280 bbl. a day of condensate and 14,750,000 cu. ft. of gas (½-hr. gauge) through a ?-in. bean. Prior to the drilling of this well, the Ohio Oil Co. discovered and developed a small gas field, which embraces a part of three townships about their common corner but lies chiefly in secs. 31 and 32, T.31S., R.26E. The first well was completed on July I, 1934, at a plugged depth of 5239 ft. after having been drilled to 7957 ft, production was found in a 59-ft. zone IIO ft. below the Fourth Mya bed, within the Sari Joaquin clays. Until recently this field was known as the Buena Vista gas field. It is now carried by the Division of Oil and Gas as the Paloma gas field. Production within the Paloma gas field is derived from six wells, producing from several different zones in the interval from 4177 to 5548 feet. Geology Stratigraphy The sediments penetrated by wells in the Paloma held range in age from Recent to Upper Miocene. The entire section, which exceeds 10,000 ft. in thickness, conforms generally to the standard section of the south central San Joaquin Valley. The producing zone, sometimes called the Paloma sand, is the approximate equivalent of the Stevens sand zone of the Ten Section, Canal, Coles Levee and other fields. The stratigraphic section is shown in Table I. Paloma Producing Zone* (Stevens Sand Zone, Upper Miocene) .-The Paloma producing zone (Fig. 2), frequently referred to as the Paloma sand, is encountered at depths ranging from 9950 to 10,300 ft. In general, it is a massive, firm to hard, not too well sorted, fine to medium fine sand. It is interbedded with thin, hard, calcareous sand shells of similar texture and cherty

Jan 1, 1942