Search Documents

By H. L. Luo, P. Duwez, C. C. Chao

BY rapidly cooling alloys from the liquid state, it is possible to obtain solid solutions beyond the equilibrium concentrations, provided that the components are miscible in the liquid state. Typical such cases include CU-Ag,1 Pt-Ag,2 CU-Rh,3 nickel-base alloys with silicon, germanium, and tin,4 and cobalt-base alloys with silicon, germanium, tin, aluminum, and gallium.5 In the present note it is shown that terminal solid solutions can be appreciably extended in A1-Mg alloys. The alloys whose compositions are given in Table I were prepared by induction melting in tantalum crucibles under an argon atmosphere. Both aluminum and magnesium were 99.99 pct pure. Weight losses after melting were less than 0.2 pct for the aluminum-rich alloys and less than 0.4 pct for the magnesium-rich alloys. From these weight losses it was estimated that the compositions of the ingots after melting were accurate within 0.3 at. pct for aluminum-rich alloys and within 0.5 at. pct for magnesium-rich alloys. As indicated in Table I, the compound AuCd10 in which there is an ionic contribution to the bonding. The authors thank Dr. J. H. Westbrook of the Research Laboratory, General Electric Co., for arranging the supply of materials and for his interest. This investigation was supported by the U.S. Atomic Energy Commission under Contract AT(30-1)-1002, Scope I. some of the alloys were also chemically analyzed and the results confirmed the limits of uncertainty based on weight losses. Rapid quenching from the liquid state was achieved by techniques previously described.8,7 The principle of these techniques consists of propelling a small globule of liquid alloy (about 20 mg) onto a copper substrate. The thin foils easily detached from the copper substrate were analyzed by X-ray diffraction using a Debye-Scherrer camera 114.6 mm in diameter and either nickel-filtered copper Ka or iron-filtered cobalt Ka radiation. Since the back-reflection doublets were resolved, the wavelengths used in the computatioas were CuKal = 1.54050A and CoKa1= 1.78892A. Lattice parameters were obtained by extrapolation of the Nelson-Riley function, and the tables compiled

Jan 1, 1964

By E. S. Rowland, J. Welchner, R. H Marshall

This paper presents results on an extension into the realm of high-carbon steels of some work recently published1 on the effects of time at temperature, quenching temperature and prior structure on the hardenability of one 0.20 and four 0.40 per cent carbon alloy steels. It was shown at that time that unless the conditions of time, temperature and prior structure are substantially the same in performing the hardenability test as in conducting hardening of parts in production, the correlation of hardenability information with the hardness and properties of production parts is often not of satisfactory accuracy. The general effects of these variables on the austenitic grain size, distribution of excess carbides and critical cooling rate have been known for many years and one or more have been investigated by Shepherd,2,3 Davenport and Bain,4 Digges,5,6 Digges and Jordan,' Post and associates8 and Roberts and Mehl,9 to mention only a few. There has been no systematic investigation, however, into the quantitative variations produced on the hardenability of commercial high-carbon steels by changes in these factors of time, temperature and prior structure. Procedure A plain carbon hypereutectoid steel, S.A.E. 52100 and Graph-Mo, a molybdenum-bearing high-carbon steel containing some graphite, were chosen for this investigation. The chemical analyses of these electric-furnace steels are given in Table I. The procedure used was exactly that reported previously,' hence the details will not be repeated here. Normalized (165o°F.) and spheroidized prior structures were utilized on all steels with hot-rolled and quenched (I600°F. oil) prior conditions added for the plain carbon steel. The end-quench test developed by Jominy10 was sclected for use in this investigation and, with the noted exceptions, the American Society for Testing Materials standard procedure was followed. The effect of time at temperature was examined at intervals of o, 10 and 40 min. and 4 hr., and a few 16-hr. tests were run. Salt-bath heating of the specimens was employed to control and minimize the

Jan 1, 1944

By R. H. Marshall, J. Welchner, E. S. Rowland

This paper presents results on an extension into the realm of high-carbon steels of some work recently published1 on the effects of time at temperature, quenching temperature and prior structure on the hardenability of one 0.20 and four 0.40 per cent carbon alloy steels. It was shown at that time that unless the conditions of time, temperature and prior structure are substantially the same in performing the hardenability test as in conducting hardening of parts in production, the correlation of hardenability information with the hardness and properties of production parts is often not of satisfactory accuracy. The general effects of these variables on the austenitic grain size, distribution of excess carbides and critical cooling rate have been known for many years and one or more have been investigated by Shepherd,2,3 Davenport and Bain,4 Digges,5,6 Digges and Jordan,' Post and associates8 and Roberts and Mehl,9 to mention only a few. There has been no systematic investigation, however, into the quantitative variations produced on the hardenability of commercial high-carbon steels by changes in these factors of time, temperature and prior structure. Procedure A plain carbon hypereutectoid steel, S.A.E. 52100 and Graph-Mo, a molybdenum-bearing high-carbon steel containing some graphite, were chosen for this investigation. The chemical analyses of these electric-furnace steels are given in Table I. The procedure used was exactly that reported previously,' hence the details will not be repeated here. Normalized (165o°F.) and spheroidized prior structures were utilized on all steels with hot-rolled and quenched (I600°F. oil) prior conditions added for the plain carbon steel. The end-quench test developed by Jominy10 was sclected for use in this investigation and, with the noted exceptions, the American Society for Testing Materials standard procedure was followed. The effect of time at temperature was examined at intervals of o, 10 and 40 min. and 4 hr., and a few 16-hr. tests were run. Salt-bath heating of the specimens was employed to control and minimize the

Jan 1, 1944

By John D. Sullivan

Leaching of copper ores is a comparatively old art, probably dating back to medieval times. The leaching of mixed oxidized-sulfide ores, however, is modern. The first modern plant leaching mixed ores was at Ajo, Ariz., where commercial operations commenced in 1917. While the ore at Ajo was primarily oxidized there was always some sulfide present. The Inspiration leaching plant, which was put in operation in 1926, may be considered the first plant constructed for the extraction of both sulfide and oxidized copper. The pioneers in leaching mixed ores had a difficult task before them since they had very little fundamental data on the chemical and physical factors of leaching. For the very large amount of painstaking experimental work that was done before building the Ajo and Inspiration leaching plants the reader is referred to the original articles.' For a period of several years the writer worked on problems connected with the chemistry and physics of leaching mixed oxidized-sulfide ores. This paper summarizes the experimental work and discusses various factors involved in leaching ores. It also presents many data heretofore unpublished. Among the new data are those on chrysocolla, pages 518 to 519, inclusive; dioptase, page 519; covellite, page 529; virtually all those on chalcopyrite, pages 531 to 533, inclusive; enargite, page 533; and tetrahedrite and tennantite, pages 534 and 533. The oxidized copper minerals of commercial importance in American ores are azurite, Cu3(OH)2(CO3)2; malachite, Cu2(OH)2CO3; chrysocolla, CuSi03.2H2O; tenorite (or melaconite), CuO; and cuprite, Cu2O. Dioptase, CuSiO3.H2O is less common. Brochantite, CuSO4.3Cu(OH)2, while the chief mineral in the ore at Chuquicamata, is not of major importance in the United States. Metallic copper, while chemically not so, is frequently classed as an oxidized mineral of copper. The most important sulfide minerals are chalcocite, Cu2s; covellite, CuS; bornite, Cu5FeS4; and chalcopyrite, CuFeS2. Less important complex sulfides are enargite,

Jan 1, 1934

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By G. F. Loughlin

More than 20 years have passed since the publication of Lindgren and Ransome's report on the Cripple Creek District,1 which was made when the district was much more active and prosperous than in recent years. They concluded that the output of the district, which had reached its maximum of about $18,200,000 in 1900, would gradually decline, and their conclusion has been confirmed by records of subsequent production. Between 1905 and 1915 annual declines were partly compensated by encouraging increases, especially in 1908, 1914, and 1915; but a rapid continuous decline followed, due largely to the war and its after-effect's, until in 1922 the value of output was only slightly more than $4,000,000. It rose to nearly $5,000,000 in 1924, but declined again in 1925 and in 1926, when it was about $4,400,000, and represented ores mainly from deep levels in the Cresson and Portland mines. The profitable operations of these two mines were the principal factors leading to a study of ore at deep levels in the district by the U.S. Geological Survey in cooperation with the Colorado Metal Mining Fund. The principal reasons for Lindgren and Ransome's conclusion were three: (I) the greater cost and difficulty of deep exploration; (2) the decrease in the number of veins with increasing depth, and (3) the probability that the telluride ore, believed to have formed at comparatively low temperature, would not persist indefinitely in depth. Operations since they made these statements have verified the first two, but call for some modification of the third. Rich telluride ore is being mined at a profit in the Portland mine 3000 ft. below the present surface, 07. 5000 ft. below the original surface of the Cripple Creek volcano, as interpreted by Lindgren and Ransome. The question arises, therefore, as to the number and extent of such deep deposits, and the answer, so far as it can now be given, must be based mainly on structural data, supplemented by data on the processes of ore deposition. Presentation of these data based on a study of deep mines in the southeast quarter of the district, the only

Jan 1, 1927

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By John H. Hall

The Frémont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about # by 6 by about 16 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Frémont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. In this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions. In testing coupons cut from castings heat treated by quenching and annealing, attention was drawn to the wide variations in the value of the Frémont test of specimens cut from different parts of the coupon. The latter was of the form and dimensions shown in Fig. 1, and Fremont test pieces were cut from two parts of this coupon, marked A and B in that figure. The results of the tests are shown below, tests A and B in each instance being from the same coupon: A. B. A. B. Coupon. Kilogram- Kilogram- Coupon. Kilogram- Kilogram- meters. meters. meters. meters. 1,........ 12.0 12.5 9,........ 27.5 32.5 2,........ 11.0 32.5 10,........17.5 31.0 3,........ 11.5 30.0 11,........ 14.5 31.0 4,........ 20.0 33.0 12,........ 15.0 27.5 5,........ 17.5 33.0 13,........ 19.0 30.0 6,........ 17.5 20.0 14,........ 17.5 25.5 7,........ 17.5 13.0 15,........15.0 30.0 8,........ 10.0 30.0

Jan 1, 1914

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported' that acid-soluble titanium decreased creased the hardenability, with multiplying factors less than unity according to [ ] Grossmann's system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying factors up to nearly 1.7 for about o.' per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 2.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and, Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correction for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. COMPARISON OF PLAIN-CARBON, VANADIUM AND TITANIUM STEELS The five steels used for these experiments were commercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat, containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by, adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain-carbon coarse-grained S.A.E. 1040 steel made by the basic open-hearth -process. No. 5

Jan 1, 1945

By Edward Steidle

Those who have followed the rapid progress in rock-dusting bituminous-coal mines must admit that opinion crystallized during the year just closed in support of this preventive of coal-dust explosions. Up to 1924 only one mining company in America practiced rock-dusting on a large scale, but during 1924 forty-two companies had adopted this safety measure, and the "boom" is expected to extend over the next two or three years. Alabama is represented by 1 company, Colorado by 3, Illinois by 4, Kentucky by 1, New Mexico by 4, Pennsylvania by 20, Utah by 8, and Wyoming by 1. A total of about 500 miles of entry has been dusted. Illinois leads with 275 miles of dusted entries and Pennsylvania holds second place with about 175 miles. In each case there is a sense of great security, not only on the part of the operator but by the miner as well. It is also interesting to note that during 1924 the compensation rating or inspection bureaus in twelve of our coal-producing states revised their rating schedules so that a credit would be given for rock-dusting. This credit ranges from 10 to 20 cents per $100 payroll. Recent drastic federal and state regulations approved by mine operators made rock-dusting compulsory in bituminous coal mines in Utah, beginning July 1, 1924. Legislative action favorable to rock-dusting may be expected in other states. Colorado has already proposed a change in its laws, and Pennsylvania, Maryland, Washington, and West Virginia are giving the matter consideration. If the rock-dusting problem is handled properly and proves to be entirely successful, no mining man of any standing will delay applying it in his mine. State legislation regarding this matter may or may not solve the problem. At present, the mining companies that are rock-dusting of their own choice are doing it carefully and thoroughly. In Utah, some are doing it conscientiously, trying to get what benefits can be obtained while others are reported to be doing it only to keep within state regulations. In any event, if we are to have new legislation, it is essential that the various states know what they are about and then, if possible, work for uniform regulations.

Jan 1, 1925

By T. B. Counselman

An iron blast furnace of 1000 tons daily capacity will produce a 100,000 cu. ft. per minute of blast-furnace gas. This contains a 25 per cent of carbon monoxide, and has a B.t.u. value of about 95. gas is used primarily for heating the stoves of the blast furnace, secondarily, under boilers, for steam production. Occasionally it is used in gas engines. The raw gas coming out of the furnace carries about 10 grains of dust per cubic foot of gas, under best operating conditions. With furnace "rolling" or slipping, this quantity may temporarily be gre increased. This dust would, of course, deposit on the checkers o: stoves, or plug the burners under the boilers; therefore the gas : be cleaned. Flow Sheet The first step in the cleaning operation, as shown by the flow s Fig. 1, is a dry dust catcher, of which there are several forms, partially cleaned gas next goes to a primary wet washer, where v sprays knock down most of the solid particles. If further cleani desired, the gas may then go to electrical precipitation. Again, the removed is collected in water. Dry dust catchers reduce the dust col from 10 grains to between 4 and 6 grains per cubic foot, and rec roughly half of the total flue dust in the gas. The wet washers rea most of the remaining dust, reducing the dust content to about 1/4 per cubic foot. Electrical precipitators, if used, further reduce the content to about 0.01 grain per cubic foot of gas. The flow sheet s the dust content of the gas at various steps in the treatment and als content of solids in the water. It should be noted that some plant less water on the primary wet washer than indicated, and that ofte solids content of the scrubber water will be 300 grains per gallon, or much higher. Reasons for Recovering Flue Dust.—There are two main incentive recovering flue dust from the scrubber water: (1) the value of the (2) stream or lake pollution, where such a reason applies.

Jan 1, 1937

By Henry Hebley

IN preparing this paper it has been the aim of the writer to keep the problems of both producers and consumers in mind. Until now, no attempt has been made to familiarize each group with the other's practice and limitations. This paper is an effort to acquaint the readers with some of the factors pertaining to the problem and cost of mining and preparing steam coal, and also to the economics of producing steam with such coal. In recent years all lines of endeavor have turned to intensive mechani-zation in order to lower the unit cost of production. The average fuel consumption in steam electric generating stations has dropped in 20 years from 4.0 lb. to 1.4.1b. per kilowatt-hour; while the modern power station can generate 1 kw-hr. on a fraction under 1 lb., or 13,000 B.t.u. coal. Also, the amount produced per man has in that same period risen from 3.8 to 8.2 tons, owing to the use of modernized equipment below ground for coal cutting, drilling, shooting, loading, hauling and hoisting. Unfortunately, the rapid speed of 5 tons per minute of operation at which the coal is loaded mechanically precludes any appreciable removal of impurities at the coal face, so that the raw coal is hoisted containing a markedly higher percentage of impurities than the hand-loaded coal, which was subjected to the scrutiny of the miner during loading. Also, during the past 20 years, certain seams of coal lying close to the surface have been made economically available by the improved design of electrically operated shovels and draglines for the removal of overbur-den running as high as 56 ft. This strip coal frequently contains so much ash in the raw state (Table 1) that it would have no sales value. There-fore, coal preparation must be adopted to beneficiate the raw product. Some seams in the United States have a decreasing ash content with decreasing size, owing, in all probability, to the fact that the coal is friable while the impurities are hard, causing a concentration of the low-ash material in the fine sizes. Illinois No. 6 coal being rather hard, naturally the reverse is true.

Jan 1, 1937

By Paul A. Farrar, Felix Ermains, Harold Margolin

The systems Ti-Crand Ti-Vhave been reinvesti-gated in the region up to 40 wt pct alloying addition using both conventional and rapid quenching techniques. The Ti-Cr eutectoid temperature was determined to be at 667° & 10° C and 14.5 wt pct Cr. The solubility of the Cr in a Ti was found to be less than 1 pctat 700"C. The P transus of the Ti-V system was found to be depressed to 510°C at 40 wt pct V and the solubility of V in a Ti was found to be less than 2 wt pct at 700°C. Investigation by a. d. McQuillan1-3and m. k. McQuillan4 on the systems Ti-Co, Ti-Cr, Ti-Cu, Ti-Fe, Ti-Mn, Ti-Ni, and Ti-V has cast doubt as to the position of the ß/a + ß boundaries in many of these systems. Their investigations were carried out using hydrogen pressure and/or rapid quenching experiments, as opposed to the conventional quartz capsule techniques employed by most other investigator.'" By these methods, the ß/a + ß boundary was found to be lower than that obtained by conventional techniques in all except the Ti-Fe system. In the latter, the ß/a + ß boundary was essentially the same as the boundary obtained by conventional technique.7' On the basis of rapid quenching results in the Ti-Cr system, M. K. McQuillan4 placed the eutectoid temperature below 550°C whereas other investigations using conventional techniques had placed the eutectoid variously as between 650' and 700°C,5 between 675' and 700°C,6 between 650" and 675°C,7 at 670°C,8 and above 625"C.la9l3 In order to check these results, a reinvestigation of four of the systems was undertaken using both conventional and rapid-quenching techniques. The Ti-Fe and Ti-Mn systems will be dealt with in anoth er paper, with only the Ti-Cr and Ti-V systems being discussed here. EXPERIMENTAL TECHNIQUES Alloys employed for the delineation of the systems under investigation were prepared from iodide titanium sheet capsules containing the alloying materials,

Jan 1, 1962

By R. E. Hobart

THE development of the Hauto power plant and the claims made by various engineers that electricity was more economical than steam for power purposes in and about the mines; led the Lehigh Coal and Navigation Co., in 1911, to conduct a test to ascertain the consumption of power used by a large steam hoisting engine. The question being one on which no reliable information could be found, and the opinion of various engineers differing to such an extent, it was decided that a test under actual operating conditions was necessary. This was arranged for at one of the collieries. The engine selected was a 30 by 60-in. (76.2 by 152.4-cm.) piston-valve engine of modern type, and comparatively new. The boiler plant from which the hoist received its power was about 600 ft. (182 m.) from the engine, the latter being fed by a 10-in. (25.4-cm.) steam line insulated with magnesia pipe covering. Two batteries of the boiler plant, aggregating 1200 hp., were cut off and fed into a separate steam line leading direct to the hoist engine. Steam auxiliaries, consisting of feed-water pump and blowers, were fed by the boilers in test, and their consumption charged against the hoist. A barrel weighing device was installed, as it was felt that this would be the most accurate way of determining the consumption of water. The fuel, No. 3 buckwheat, was carefully weighed, and every precaution was taken to make the test accurate in every particular. The test was run for 1 week, or a total of 168 hr. A record was kept of the number of trips hoisted or lowered, and continuous indicator cards were taken. One particular set of cards was taken with the hoist operating balanced, and also with the hoist operating with no counterweight other than the empty cage, the coal in the car being weighed. The speed of the hoist was taken by means, of a graphic recording instrument which registered the number of revolutions every 5 sec. From this record, speed-time curves were plotted.

Jan 2, 1918

By E. L. Mann

Asbestos is the generic name given to a group of fibrous mineral silicates found in nature. They are all incombustible and can be separated by mechanical means into fibers of various lengths and cross sections, but each differs in chemical composition from the others. The commercial grades of asbestos consist of a spectrum of lengths and sizes and are not definitive as are most organic fibers. It is generally recognized that there are two main groups of asbestos. The first only contains the fibrous serpentine called chrysotile and comprises about 94% of the world production of asbestos. The second group contains five minerals in the amphibole series-crocidolite, amosite, anthophyllite, tremolite, and actinolite. The latter two have no commercial importance. Properties Physical The structures of asbestos fibers have been studied intensively over a number of years. X-ray diffraction patterns have been used as a means of identification and classification. Low angle X-ray scattering techniques have shown that chrysotile fibers are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 18Å to 300 Å units, while the amphibole fibers are many times larger in cross section, have considerably smaller surface areas, and the fibers are less symmetrical than those of chrysotile. Electron micrographs of the more common types of asbestos are shown in Figs. 1-4. Fig. 1 illustrates the softness and flexibility of chrysotile which make it suitable for textile-type products. For a number of years there was considerable controversy over the exact nature of chrysotile fiber, but the photographic evidence in Figs. 5-7 clearly show that it is tubular in structure. The curvature is the result of the mismatch in the dimensions of the silica [Si2O5] and brucite [Mg(OH)2] layers which are on the inside and outside, respectively, of a double sheet. This curvature had been predicted by Pauling (1930) years ago based on the molecular dimensions of the two component structures. In contrast to this, the structure of the amphiboles consists of two ribbon chains based on Si4O11 units separated by a band of seven cations with two hydroxyl groups attached to

Jan 1, 1983

By W. C. Hagel, H. J. Beattle

DURING an earlier examination of high-temperature alloy, A-286, the presence of an unknown intermetallic compound was verified by X-ray diffraction. Owing to its prominent appearance at grain boundaries, the arbitrary name of G phase was assigned.' Low-silicon, vacuum-melted heats were found to contain no G phase, and this investigation was initiated to determine the influence of silicon on G-phase formation; additional work was undertaken to extend existing data on other intermetallic compounds and the aging reactions in this group of alloys. Taylor and Floyd2-4 observed that the Ni3Al phase (y') and the Ni8Ti phase (7)) are the only equilibrium intermetailic compounds in nickel ternary alloys containing up to 25 pct Cr and 10 pct Ti or Al. They found that y' can dissolve considerable nickel, chromium, and titanium, although the stoichio-metric composition of 7 remains fixed. Nordheim and Grant5 confirmed that age hardening of 80 pct Ni-20 pct Cr alloys of the Nimonic-80 type is due to precipitation of y', where aluminum is partially replaced by titanium. They suggest that optimum hardness and ductility result from increasing the titanium to aluminum ratio toward the end of the y' solubility range and from increasing total titanium and aluminum content to the maximum limit permitted by processing. Such information is necessary for those seeking to improve the service-temperature range and long-time structural stability of high-temperature components. Experimental Methods Compositions of materiais studied. are listed in Table I. Alloys D, E, and F possess representative A-286 analyses; silicon increases from less than 0.02 to 1.75 pct in alloys A to H; in alloys I to K, titanium decreases from 2.24 to 0.39 pct, and aluminum increases from 0.1 6 to 240 pct. Alloys A and D were solution heat treated for 4 hr at 1700°F, oil quenched and aged for 0.5, 2, 6, 12, 30, 70, 200, and 1000 hr at 1200°, 1300°, 1400°, and 1500°F. Therefore, a total of 33 specimens was required for each

Jan 1, 1958

By F. H. Wilson

Copper base alloys containing various amounts of aluminum and silicon are of considerable commercial interest. In particular the alloy containing 7 pct aluminum and 2 pet silicon shows an attractive combination of high strength with excellent, machinability. Since there is no evidence ill the literature that this ternary system has been studied since the recognition by Smith1 and Anderson2 in 1939 of the kappa phase of the binary copper-silicon system, the determination of the equilibrium phase relationships in the copper corner of the ternary diagram has been undertaken to provide a fundamental basis for understanding the behavior of these alloys. Phase boundaries have been determined by the micrographic examination of quenched samples while points on the liquidus surface have been obtained by thermal analysis. The results, of sufficient precision to serve their major purpose of providing a guide for the control of the manufacture of alloys in the region covered, are presented in a series of both isothermal and vertical sections of the diagram. Alloys StVdied For a rough survey of the copper corner of this ternary system the compositions listed in Table I (Series A) were employed. The results of examinations of these alloys indicated that the compositions listed in Table 2 (Series B) would further clarify regions of greater complexity. All alloys were prepared as 1200 g heats, the copper being melted under charcoal, and then first silicon and then aluminum were added. An excess of 0.05 pet silicon was allowed to cover deoxidation losses. Two small bars 5/8 by 1 1/4 by 5 1/4 in. were cast using Durville type casting equipment. Ailalyses were made on all alloys using material which was hot-rolled at 800 or 850°C and annealed 17 hr at 650°C. All analyses were found to be within 0.05 pet of the nominal composition. Since the precision of analysis is not much better than this, the points of both isothermal sections and vertical sections at fixed aluminum and silicon contents have been plotted at the compositions indicated by the nominal composition.

Jan 1, 1949

By Leonid V. Azároff, H. N. Murty

In the course of investigating the soft X-ray absorption spectra of Ni-A1 alloys, Das and ~zfiroff' observed an anomalous brittleness in solid solutions containing 3 to 5 at. pct Al. The brittle alloys also had anomalously larger lattice constants' and the fine structure at the nickel K edge of an alloy containing 3.96 at. pct A1 unexpectedly resembled that of NiA1 more closely than that of a solid solution containing 5.51 at. pct Al. This led them to suggest the possibility that short-range ordering was produced during the homogenization anneal to which each specimen was subjected, similar to that observed in dilute solutions of vanadium and of chromium in nickel: as the principal cause of embrittlement. It was decided to repeat the above measurements on several alloys in this composition range in order to test the above hypothesis and to establish the effect of heat treatment on the alloys' properties. Three solid solutions in this range were prepared containing, respectively, 3.16, 4.00, and 4.54 at. pct Al, in addition to alloys containing 6 and 9 pct. All samples were annealed in vacuum at 1800°F for 100 hr and then furnace-cooled to room temperature, as in the original study. The lattice constants of these alloys are shown by open circles in Fig. 1 and can be seen to fit quite closely the curve established by the previously measured values, indicated by solid circles. (The experimental errors are of the order of the size of the circles, +o.oo~R.) The three alloys containing 3 to 5 at. pct A1 were found to be quite brittle, as previously reported. In order to test the possibility of ordering, these three solid solutions were again heated to 1800°F and, following a few hours at that temperature, were quenched directly to room temperature. All three alloys lost their brittleness. In order to verify the proposed ordering hypothesis, it was decided to subject each sample to several cycles of quenching and annealing (disordering and ordering). After some experimentation, it was established that reproducible results could be obtained by anneal-

Jan 1, 1968

By C. D. Hunter, J. B. Browning

During the year 1934, Kentucky oil and gas operators have partly overcome their past depression fears and in the oil industry, with possibly more abandonments of old oil producers than the completion of new oil wells, produced 4,814,904 bbl. of oil in 1934 against 4,501,511 bbl. in 1933. In the gas industry of eastern Kentucky, 115 gas wells were completed during 1934. This production is delivered through two 20-in., one 16-in., one 12-in., one 10-in., and two 8-in. pipe lines to supply both domestic and industrial markets in Cincinnati, Ohio; Louisville, Lexington, Frankfort, Winchester, Ashland, Covington and other Kentucky towns; Washington, D.C., and other eastern cities. The largest percentage of these gas wells and production are from the Devonian black shale area of Floyd, Pike, Knott, Martin and Magoffin counties, Kentucky. In this area the largest percentage of 1889 wells, developing 421,-215 acres, has been completed in the past 10 years, of which 55.3 per cent produce from the 400 to 550 ft. of Carbonaceous Devonian black shales. The successful results obtained from these Devonian shales are due to the physical effects of the 5000 to 6000 lb. of gelatinated nitroglycerin with which the entire 400 to 550 ft. of shale is shot. A very small number of the shale wells are natural producers and do not require shooting. Other than the Devonian shale gas production, the remaining 44.5 per cent of the gas in this field is encountered throughout the entire strati-graphic section above this horizon; namely, salt sands of Pennsylvanian age and Maxon, Big Lime and Weir of Mississippian Age. A very small percentage is encountered in the Corniferous Devonian lime and the Silurian Big 6 below the black shales. In western Kentucky, in the counties of Henderson, Webster, Hopkins, McLean, Christian, Muhlenburg, Ohio, Daviess, Hancock, Brecken-ridge, Hart, Barren and Warren, many gas wells have been completed, but, because of insufficient market, activity has been somewhat desultory. The area is served by the pipe lilies of the Kentucky Natural Gas Corporation, with headquarters at Owensboro. Their market is increasing and the gas is delivered to Owensboro, Henderson, Madisonville, and many

Jan 1, 1935

By A. C. Callen

This, report represents the comments of the individual members of the A. I. M. E. Sub-committee on Physics of Mine Ventilation on the proposals of a special committee of the Institution of Mining Engineers (London). As might be expected, there is a certain diversity of opinions, for owing to the shortness of time- it was not possible for the sub-committee to get together for informal discussion. The report is presented in this form in the hope that it will bring out a full discussion by other members in the Institute. OLE SINGSTAD?, New York, N. Y.-The Atkinson formula, P =SV2 K a is quoted and it is stated that this formula is especially applicable to mine galleries but is unwieldy in application, as in many problems the value of K, S and a are assumed not to change. This is the same formula that was used during the preliminary calculations for the ventilation of the Holland Tunnel, and where the above-mentioned values were constant for a number of cases, it was a very simple matter to rewrite the equation n the form P = K1V2 and avoid the repeated use of identical figures. The Atkinson formula assumes 1. That resistance to flow is independent of the pressure. 2. Changes in volume due to change in pressure may be neglected. 3. Changes in density and viscosity may be neglected. 4. That the coefficient K is a constant. 5. That P is proportional to V2. We found, from our experiments in connection with the ventilation of the Holland Tunnel, that all the above assumptions could be safely made, with the exception of No. 3, and No. 4 at, very low velocities. In mine work, where many assumptions must necessarily be made, it would seem inconsistent to attempt to make any allowance for the other factors, which are so small that they can be determined only by the most careful experimental work. However, P does depend directly on the density of the air, and to that extent the Atkinson formula is incomplete.

Jan 2, 1926