Search Documents

By M. N. Shetty

LARGE copper whiskers were grown from cuprous iodide by reduction with hydrogen at about 500°C. Carefully selected single-crystal whiskers of [loo], [110], and [Ill] orientations were used and the whisker shapes and cross sections are shown in Fig. 1. Spec-trographic analysis of a typical batch of whiskers showed that the composition was better than 99.9 pct with iron and silicon as the major impurities. The test specimens varied from about 70 to 400 u in diam and they did not show a conspicuous yield drop as observed in very fine whiskers (diam <25 u), tested by Brenner.1 The characteristics of the stress-strain curves were similar to those of bulk single crystals, even though the maximum flow stresses reached in some orientations were comparable to the yield stresses observed in fine whiskers. Mechanical properties of whiskers of different materials and copper whiskers up to about 100 u in diam have been reviewed,&apos; and a mechanism of slip band propagation in fine whiskers has been recently suggested.3 Whiskers in this work were tested in a floor-model Instron testing machine using low strain rates. (Details of the testing procedure, diameter dependence of the yield stress, and the characteristics of the load elongation and stress-strain curves have appeared esewhere.4) Due to the extensive deformation, >50

Jan 1, 1970

By Holbrook Botset

EXPERIMENTS performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This con-clusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely con-solidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be intro-duced was the cementing material.

Jan 1, 1939

The opening session of the Institute was held at the rooms of the American Society of Civil Engineers, No. 4 East 23d Street, VicePresident R. W. Raymond in the chair. After a short introductory address by the chairman, the following names were presented by the Council for election as members and associates of the Institute. They were unanimously elected : MEMBERS. Abbott, James W.,.....Lake City, Col. Abbott, J. J., Jr.,...... Lake City, Col. Bartlett, J. C.,.....Cambridge, Mass. Billings, G. H.,.....Boston, Mass. Blake, Frank C.,.....Lafayette College, Easton, Pa. Dewey, Fred. P.,.....Lafayette College, Easton, Pa. Douglass, Samuel T.,. .. . Ann Arbor, Mich. Emmons, 9. F.,.....New York City. Engle, George U.,.....Philadelphia. Harrington, Dr. Bernard J.,. .. Montreal, Canada. Hayden, Wm. B.,.....Columbus, O. Hill, Leslie C.,.....Capelton, Quebec, Canada. Land, W. J.,......Atlanta, Ga. May, Wm. A.,.....Scranton, Pa. Mills, James E.,.....St. Louis, Mo. Moore, Charles W.,.... Montezuma, Ind. Page, William Byrd,.... Lexington, Ky. Putnam, Douglas, Jr.,.... Ashland, Ky. Richards, Henry,.....Dover, N. J. Boberts, Percival, Jr.,. .. . Philadelphia. Sackett, S. G.,......Brooklyn, N. Y. Schley, Wm. S.,.....Atlanta, Ga. Setz, Gustav,......Mine La Motte, Mo. Talhutt, John H.,.....Lexington, Ky. Torrey, Herbert G.,.... U. S. Assay Office, New York City. Wernlitz, Fred. W.,..., Cartersville, Bartow Co., Ga. Wiestling, Geo. B.,.....Mont Alto, Franklin Go., Pa.

By M. J. Duggin

Evidence is produced below to show that the carbide "Mn,C," reported by Kw,and ersson&apos; is really a mixture of two carbides. One is an Fe-Mn carbide which is probably isomorphous with hexagonal Mn15C4, reported by Bouchand and Pruchart.&apos; The othev is a tetragonul Fe-Mn carbide with cell dzmensions close to those reported previously by the author3 for an Fe0.1Mno. carbide. IN a recent investigation several Fe-Mn carbide specimens, each weighing about 5 g, were prepared in a manner previously reported.3 Debye-Scherrer X-ray photographs were taken of at least two samples from different parts of each specimen using a 114.6-mm-diam camera. The exposure time was 2 hr using filtered chromium radiation, a tube voltage of 35 kv and a tube current of 10 ma. In the case of one specimen, which contained nominal weight percentages of iron, manganese, and carbon of 9.40, 84. 6,, and 6.0, respectively, duplicate chemical analyses indicated f1.2 and 5.5 wt pct C to be present in the two samples taken of the specimen: no graphitic carbon was detected. One powder-diffraction pattern of this specimen indicated the presence of the tetragons: carbide reported earlier,3 (a = 6.772A, c = 9.427A), plus cementite (O), plus an unknown structure. The second powder-

Jan 1, 1970

By J. Stringer, I. W. Edington, C. R. Rarey

THE geometrical interpretation of transmission electron micrographs of hcp metals is more complicated than the equivalent interpretation of cubic metal for two reasons: firstly, prominent zone axes are not in general normal to prominent planes, so that a simple diffraction pattern often corresponds to a nonra-tional foil plane; and secondly, the Miller-Bravais sys-tem of indexing directions is not easy to visualize. In this, the indexing is referred to the Bravais four-axis system, and the direction is labeled [hkil], chosen so that and I are shown in Fig. 1. Some geometrical relationships useful for the interpretation of transmission micrographs have been calculated and are tabulated below: 6) Direction of the intersection of two planes; this is easily calculated by applying Condition 4 to both planes: a direction that lies in both planes is clearly their direction of intersection. Some of the above expressions have also recently been given by Otte and Crocker;&apos; Expression 5 is of course in most standard crystallographic texts. It is generally considered easier and quicker to use graphical methods for the interpretation of electron micrographs than analytical methods. For this purpose, it is most convenient to use a "double stereo-gram" in which both the poles alzd the rational directions are plotted. It is, of course, necessary to orient

Jan 1, 1967

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The apparatus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a ½ -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1-The fine coal, which has been thoroughly

Jan 1, 1952

By J. H. Clemes

The process of leaching silver ores with sodium hyposulphite is comparatively new, and published accounts of the details and losses of the process are as yet very few. The following account of a careful series of experiments to determine the actual loss in this process may therefore be acceptable to members of the Institute. The ore treated was highly calcareous, and the principal sulphide present was iron pyrites. Following is an analysis by Professor Price, of San Francisco, of the ore treated : Per cent. Silica,..........15.13 Sulphur,.........13.31 Arsenic,.......... 9.82 Iron............ 17.33 Alumina,..........1.35 Zinc,...........4.92 Lead,..........1.78 Carbonate of lime,..33.78 Magnesia,.......... 2.58 100.00 Ten tons were crushed dry with a 30 X 30 screen = 900 holes per square inch. In order to feel our way with this ore, two experimental or "pilot" charges were roasted. Pilot Charge No. 1. Treated 1000 pounds in a four-hearth reverberatory. 8.30 p.m.—Entered fourth hearth, remaining there one and onehalf hours; sulphur began to burn. 10 p.m.—Changed to third hearth; ore became red-hot half an hour after entering; the fireplace was kept almost destitute of fuel. 2.30 A.M.—Changed to second hearth. Charge continued, giving off a large quantity of sulphurous fume; the fireplace was kept dark.

Jan 1, 1884

By G. M. T. Marshall

Plans to bring the Geco Mines property in Manitouwadge, Ont., into production began in 1954. At that time over 12 million tons of copper-zinc ore were indicated in a zone 2700 ft long. A concentrating plant was built to handle 3300 tpd of ore and a production shaft was sunk about 1500 ft. MINE LAYOUT Vertical attitude, width, rake, and competent country rock of a 4-million ton orebody west of the main diabase dike suggested a system of blasthole stopes, undercut with scram drifts connected by a transfer raise system to a crusher on the 1250-ft level and this system was employed. A 42-in. conveyor on this level transfers the ore about 1200 ft to a loading pocket at the No. 1 shaft. The system has a number of advantages: 1) Cost of tramming is eliminated. 2) Rate of extraction from any stope is controlled only by the scraping capacity of the scram. 3) Rate of extraction from the stoping area can be very rapid. Fast extraction makes it possible to cut mining costs for the following reasons: The number of stopes actively producing is kept to an economical minimum; the operating area is concentrated-manpower can be used more effectively; and active life of the stoping block is short, making ground support problems simpler and less costly.

Jan 8, 1959

By J. L. Gillson

Historically, rock deposits and sand deposits of titanium minerals came into production about the same time, although there may be some argument as to what is meant by production. Beach de- posits of heavy minerals in India (Figs. 1-4) and Brazil (Figs. 5) were worked for monazite about the turn of century, but as there was then no market for titanium minerals, these were thrown away. The rock rutile deposits at Roseland, Va., Fig. 6, were worked to supply rutile for titanium chemicals and for coloring ceramics long before there was a titanium pigment business. The pigment industry started about the middle twenties, both in Europe and the U. S., and almost simultaneously the rock deposits at Ponte Vedra Beach near Jacksonville, Fla., were worked for titanium content. Since those days, production from both types of deposits has continued to grow at a rapid rate; many deposits of both types have been found, and reserves have grown to very large figures. In total tonnage of reserves, there is no doubt that the rock deposits are far ahead of the sand deposits; nevertheless there is a very large tonnage of commercial sands available. It is the quality of titanium mineral in the sand and the relatively lower costs of operating sand deposits that have kept them abreast, at least in annual tonnage produced, with the rock deposits.

Jan 4, 1959

By Eifu Moriyama

In 1953, Akita Plant, having a capacity of 560 tons per month, was built at Akita city by Mitsubishi Metal Mining Co., Ltd. for the purpose of treatment of the Ikuno and Akenobe Mines&apos;s zinc concentrates. Akita city, in whose neighborhood the black ore has been discovered, is located about 500 Km north of Tokyo and faced with the Japan Sea. This plant has been continuously expanded to have the capacity of 7,500 tons per month by the end of 1969. Efforts have been made to mechanize installations and to achieve continuous process. One of the characteristics of Akita Plant is the recent establishment of the residue treatment process. Many processes had been investigated, and finally commercial sulphate roasting of the residue has been carried out since 1965. At Akita Plant, special high grade electrolytic zinc, zinc alloy for die-casting (MAK brand), cadmium, cement copper and sulphur dioxide gas are produced. Sulphur dioxide gas is sent to the next door fertilizer plant to make acid. Table 1 shows production and the average assay of the electrolytic zinc and cadmium in 1969. This plant is divided into four main sections, two subsections, and residue treatment sections: Main sections are: (M-1) roasting section, (M-2) leaching and purification section, (M-3) electrolysis section, (M-4) melting and casting section,

Jan 1, 1970

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer&apos;s time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige&apos;s geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer&apos;s time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige&apos;s geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer&apos;s time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige&apos;s geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer&apos;s time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige&apos;s geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Joseph D. McClung, L. G. Austin

INTRODUCTION Run-of-mine (ROM) coal generally falls into two major groups, that from underground mining (continuous mining machines) and that from strip mining. Continuous miners produce a finer product and strip mining a coarser product that is crushed to produce the desired size. Further size reduction depends on the proposed use or uses for the coal. For example, for pulverized coal power plants as a rough general rule, the coal is ground or pulverized to 80% less than 200 mesh (0.075 mrn) before it is blown into the boiler furnace as a coal-air suspension. For solvent-refined coal processes, the desired size is about <30 mesh ( <0.60 mm) ; in fluidized bed uses, the coal is typically < in. ( < 1.6 mm); for Lurgi pressure gasifiers, the desired size is 1-2 1/2 in. (25-63 mm). Coal preparation plants typically work with a coarse size fraction of 6x1 1/4 in. (15Ox32mm). It seems probable that the next decades will see much wider application of coal cleaning before use and that the stages of crushing and pulverization from ROM coal to end use will be integrated with coal cleaning processes. Since different cleaning processes work better with different ranges of coal size and the degree of cleaning possible is inti-

Jan 1, 1979

By J. J. Scott

During 1967 wage settlements and strikes ran at a high rate and it has been estimated that union gains of 4 ½ % to 5% per year have been attained in many instances. When these events are coupled with the need to operate on lower grade and deeper deposits the need for technological advances in underground mining becomes obvious. Emphasis has been on ways to reduce the number of manshifts required per ton of product. Most significant advances have been made in rapid advance of primary mine openings, development of mobile, rubber-tired, front-end loaders and hauling units, high-speed drilling with rotary and rotary percussive units and a serious look at nuclear devices to break large volumes of ore cheaply. Boring Developments in bit manufacture and metallurgy have allowed continuous boring-type machines to be used on harder formations than was deemed feasible in the past. Hecla Mining Co. has been using raise boring equipment for drilling 9 7/8 in. diam pilot holes in raises which are later reamed in an upward direction to 48 in. diam. The machine used is a J. S. Robbins model 42R raise borer which has been used successfully to drill two relatively long 48-in. diam holes. The first was 520 ft in length at a dip of 76º, and the second was a 785-ft vertical hole.

Jan 2, 1968

By Ernest F. Burchard

MOST of the iron ore smelted in Alabama blast furnaces is mined within Alabama, although deposits in the neighboring States of Georgia and Tennessee may be drawn upon when occasion requires. Of the four commercial kinds of iron ore, the anhydrous ferric oxide, hematite (Fe2O3) ; the hydrous ferric oxide, mostly the type commonly known as limonite (2 Fe2O33H2O) ; the carbonate, siderite (FeCO3) ; and the magnetic oxide, magnetite (Fe:3O4) ; the first two are found in abundance in Alabama, the third in less than commercial quantities, and the fourth only rarely. Both the hematite and the hydroxide are found in somewhat different forms according to their geologic environment. The Red Mountain hematite, of Silurian age, that crops out in well¬defined beds for 1.50 miles northeast-southwest and 40 miles northwest-southeast is the predominant source of ore. Only a small part of this area carries ore of commercial value; Birmingham and Gadsden are now the only centers of production. The ore is of sedimentary origin, probably altered from vast deposits of greensand mixed with calcareous, fossiliferous. marine debris. Other types of hematite not vet mined commercially are in metamorphosed rocks-red ore in slates in Columbiana Mountain and specular hematite (gray ore) in quartzite in the Talladega Hills.

Jan 1, 1938

By R. W. Heckel, J. H. Smith, H. W. Paxton

The habit plane of proeutectoid cementute precipitated from austenite was studied using a two-trace surface (analysis coupled with a direct X-ray back-reflection determination of the orientatzon of the parent Matrix. The results were the same as those obtained by earlier workers1 - 2 who used Indirect methods to determine the orientation of the matrix. The data indicate that a range or habit planes in the parent phase is operative which is not in agreement with accepted existing theories. In 1933, Mehl, Barrett. and smith1 obtained a non-unique result in a study of the Widmanstätten habit plane of proeutectoid cementite. Their data are shown in Fig. 1. These results were verified by Greninger and Troiano,2 although they did not pre-sent any data. Both of these investigations relied upon indirect methods of determination of the matrix lattice orientation. Theoretical considerations of Widmanstatten precipitates have usually proved or assumed an orientation relationship between matrix and precipitate; the habit plane expressed relative to the matrix is generally unique, although it may be irrational.3 Opinion is divided as to the factors influencing the choice of habit plane. Mehl4 felt that a nucleus which was plate shaped to minimize strain energy and surface energy during its formation could maintain this shape by the point effect of diffusion; the

Jan 1, 1961

By C. H. Mathewson

BERYLLIUM, magnesium, zinc and cadmium, together with mercury, constitute a coherent sub-group of the periodic system and these metals, excepting mercury; have been studied in sufficient detail by the new X-ray diffraction methods to prove their common adherence to the hexagonal close-packed type of crystal structure with a progressive increase in axial ratio as we pass through the group from beryllium to cadmium. The first four columns of Table 1 summarize the data on crystal structure of these metals reported in the International Critical Tables.1 The last two columns are based on results obtained in the present investigation. TABLE 1.-Lattice Constants and Twinning Law of the Be-Cd Group of Hexagonal Metals Dimensions of Unit Axial Cell, A Ratio Description of Twinning Element a° c° (c°/a°) Composition Axis Plane Beryllium 2.28(3) 3.60(7) 1.58 {1012} Probably 1 {1012} Magnesium 3.22 5.23 1.621 ,1 {1012} Zinc 2.65(7) 4.94(8 1.86(2) 11012 } 1 {1012) Cadmium 2.98 5.63 1.88(5) {1012} Probably 1 {1012} Twinning has often been observed in zinc and cadmium. The general aspects of this twinning are abundantly illustrated by photomicrographs, diagrams, etc., in the papers by Romig, and Mathewson and Phillips reported to this Institute in 1927.2. A determination of the composition

Jan 1, 1928

By Edward Estabrook

THIS paper gives a brief account of the geologic and production problems encountered in the Grass Creek oil field, the methods used in their solution, and the beneficial results obtained from the work. The author wishes to acknowledge the assistance received from J. H. Pearson and Miss Ninettta A. Davis in the collection of the data and the preparation of the cross-sections. Permission for its publication was given by the officials of the Midwest Refining Co. and the Ohio Oil Co. The Grass Creek oil field is located in Ts. 98-99 W., R. 46 N., Hot Springs County, Wyo. The productive area includes about 2 1/2 mi. (4 km.) on the apex of a great anticlinal fold occupying more than 150 sq. mi. Fig. 1 shows the structural contours of the field. Oil was dicovered in the field in June, 1914; development proceeded rapidly and production rose to a maximum in 1918. The marketed production has been approximately as follows: BARRELS BARRELS 1915 94,073.5 1918 2,946,774.27 1916 1,404,183.97 1919 2,000,584.84 1917 2,780,697.51 1920 1,485,080.94 About 350 wells, 800 to 1500 ft. (243 to 457 m.) deep have been drilled to reach the upper oil sands; two companies, the Ohio Oil Co. and the Midwest Refining Co., operate the entire field.

Jan 2, 1922